White Electronic Designs Display Systems Division ENH064V1-300/450 ENH064V1-300/450 Color TFT-LCD Module Features GENERAL DESCRIPTION Panelview provides optically enhanced solutions to the standard Sharp LQ64D343 color active matrix LCD module. The first enhancement is an index matching (IM) film lamination to the front surface of the display polarizer. The IM film is available in two surface treatments - IM/Clear and IM/110 (a 10% diffusion).The second enhancement is the incorporation of an enhanced light guide (ELG) providing for up to 30% increase in brightness. This module is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a backlight unit. Graphics and text can be displayed on a 640 X 3 X 480 dot panel with 262, 144 color by supplying 18-bit data signal (6bit/color), four timing signals, +5V DC supply voltage for TFT-LCD panel driving and supply voltage for backlight. The TFT-LCD panel used for this module is a low-reflection and higher-color-saturation type. Therefore, this module is also suitable for multimedia use. Viewing angle is 6 o'clock direction. This module is the type of wide viewing angle and high brightness (350cd/m2). Backlight-driving DC/AC inverter is not built in this module. Panelview assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. Panelview does assume the responsibility for the warranty of the enhanced product. MECHANICAL SPECIFICATIONS Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions (1) Mass Surface treatment Specifications 16 (6.4") Diagonal 130.6 (H) x 97.0 (V) 640 (H) x 480 (V) (1 pixel=R+G+B dots) 0.204 (H) x 0.202 (V) R,G,B vertical stripe Normally white 175.0 (W) x 126.5 (H) x 12.0(D) 290 ± 20 IM/Clear (glossy) or IM/110 and hardcoat 3H Units cm mm pixel mm mm g - Note: 1. Excluding backlight cables. Note: This measurement is typical, and see Fig. 3 for details. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 1 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division INPUT TERMINALS TTL-LCD Panel Driving 1 CN1 Used connector: Corresponding connector: 31 2 30 ENH064V1-300/450 DF9BA-31P-1V (Hirose Electric Co., LA.) DF9 -31S-1V (Hirose Electric Co., LA.) DF9A-31 S-1V (Hirose Electric Co., LA.) DF9B-31S-1V(Hirose Electric Co., LA.) DF9M-31S-1V(Hirose Electric Co., LA.) CN1 pin arrangement from module surface (Transparent view) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Symbol GND CK HSYNC VSYNC GND R0 R1 R2 R3 R4 R5 GND G0 G1 G2 G3 G4 G5 GND B0 B1 B2 B3 B4 B5 GND ENAB VCC VCC R/L U/D Function Clock signal for sampling each data signal Horizontal synchronous signal Vertical synchronous signal RED data signal (LSB) RED data signal RED data signal RED data signal RED data signal RED data signal (MSB) GREEN data signal (LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal (MSB) BLUE data signal (LSB) BLUE data signal BLUE data signal BLUE data signal BLUE data signal BLUE data signal (MSB) Signal to settle the horizontal display position +5.0V power supply +5.0V power supply Horizontal display mode select signal Vertical display mode select signal Remarks (1) (1) (2) (3) (4) The shielding case is not connected with GND. Note: 1. 480 line, 400 line or 350 line mode is selected by the polarity combination of both synchronous signals. 2. The horizontal display start timing is settled in accordance with a rising timing of ENAB signal. In case ENAB is fixed "Low", the horizontal start timing is determined as described in Horizontal Display Position, p.6. Don't keep ENAB "High" during operation. Mode HSYNC VSYNC 480 lines negative negative 400 lines negative positive 350 lines positive negative White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 2 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH064V1-300/450 3. CDEW WEDC R/L=OPEN, U/D=OPEN display reverse R/L=LOW, U/D=OPEN 4. WEDC WEDC R/L=OPEN, U/D=OPEN display reverse BACKLIGHT DRIVING CNA, CNB Pin No. 1 2 3 Symbol VHIGH NC VLOW R/L=OPEN, U/D=LOW Used connector: Corresponding connector: BHR-03VS-1(JST) SM02(8.0)B-BHS(JST) Function Power supply for lamp (High voltage side) This is electrically opened Power supply for lamp (Low voltage side) ABSOLUTE MAXIMUM RATINGS Parameter Input voltage +5V supply voltage Storage temperature Operating temperature (Ambient) Symbol VI VCC tSTG Topa Condition tA=25°C tA=25°C - Ratings -0.3~ VCC + 0.3 0~ + 6 -25~ + 70 0~ + 55 Unit V V °C °C Remark (1) (2) Notes: 1. CK, RO~R5, G0~G5, B0`B5, HSYNC, VSYNC, ENAB, R/L, U/D 2. Humidity: 95%RH Max. at tA < 40°C Maximum wet-bulb temperature at 39°C or less at tA < 40°C No condensation. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 3 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH064V1-300/450 ELECTRICAL CHARACTERISTICS TFT-LCD PANEL DRIVING +5V Parameter Supply voltage Current dissipation Permissive input ripple voltage Input voltage (Low) Input voltage (High) Input current (Low) Input current (High) Symbol VCC MIN +4.5 TYP +5.0 MAX +5.5 Unit V Remarks (1) ICC VRF VIL VIH IOL1 IOL2 IOH1 IOH2 0.7VCC - 250 - mA mVp-p V V µA µA µA µA (2) VCC=+5V (3) - 360 100 0.3VCC 1.0 60.0 1.0 60.0 Notes: 1. VCC-turn-on conditions t1 < 10ms 0 < t2 < 10ms 0 < t3 < 1s VI=0V (4) VI=0V (5) VI=VCC(6) VI=VCC(7) Vcc 4.5V 2.7V 4.5V data t3 t2 t1 2.7V VCC-dip conditions 1. 2.7V < VCC < 4.5V td < 10ms 2. VCC < 2.7V VCC-dip conditions should also follow the VCC-turn-on conditions 4.5V Vcc td Notes: 2. Typical current situation: 3. 4. 5. 6. 7. 16-gray-bar pattern 480 line mode Vcc=+5.0V CK,R0~R5,G0~G5,B0~B5,HSYNC,VSYNC,ENAB,R/L,U/D CK,R0~R5,G0~G5,B0~B5,HSYNC,VSYNC,ENAB R/L CK,R0~R5,G0~G5,B0~B5,HSYNC,VSYNC ENAB,U/D RGB RGB RGB G3O G34 G38 ... RGB RGB G350 G310 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 4 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH064V1-300/450 BACKLIGHT DRIVING SECTION The backlight system is an edge-lighting type with single CCFT (Cold Cathode Fluorescent Tube). The characteristics of a single lamp are shown in the folliowing table.. Parameter Lamp current Lamp power consumption Lamp frequency Kickoff voltage Lamp life time Symbol IL PL FL VS LL MIN 2.0 20 - TYP 6.0 2.16 35 25000 MAX 6.5 60 800 1000 - Unit mArms W KHz Vrms Vrms hour Remark (1) (2) (3) tA=25°C tA=0°C (4) (5) Notes: 1. Lamp current is measured with current meter for high frequency as shown below. 1 Module 3 A ~ Inverter 3 pin is VLOW 2. 3. 4. 5. At the condition of YL= (300) cd/m2 Lamp frequency may produce interference with horizontal synchronous frequency,and this may cause horizontal beat on the display. Therefore, lamp frequency shall be detached as much as possible from the horizontal synchronous frequency and from the harmonics of horizontal synchronous to avoid interference. The open output voltage of the inverter shall be maintained for more than 1 sec; otherwise the lamp may not be turned on. Since lamp is consumables, the life time written above is referential value and it is not guaranteed in this specification sheet by WEDC. Lamp life time is defined that it applied either (1) or (2) under this condition (Continuous turning on at tA=25°C, IL=6mArms) 1. Brightness becomes 50% of the original value under standard condition. 2. Kick-off voltage at tA=0°C exceeds maximum value,1000 Vrms. If operating under lower temp environment, the lamp exhaistion is accelerated and the brightness becomes lower. (Continuous operating for around 1 month under lower temp condition may reduce the brightness to half of the original brightness.) In case of such usage under lower temp environment, periodical lamp exchange is recommended Note: 1. The performance of the backlight, for example life time; or brightness, is infuenced by the characteristics of the DC-AC inverter for the lamp. When designing or ordering the inverter, make sure that poor lighting caused by the mismatch of the backlight and the inverter (mis-lighting,flicker, etc.) do not occur. Once this is confirmed, the module should be operated in the same condition as it is installed in the instrument. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 5 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH064V1-300/450 TIMING CHARACTERISTICS OF INPUT SIGNALS Timing diagrams of input signal are shown in Fig. 2-1~3. TIMING CHARACTERISTICS Clock Parameter Clock Frequency High Time Data Horizontal sync. signal Vertical sync. signal Symbol 1/Tc Tch Mode all Min. 5 Typ. 25.18 - Max. 28.33 - Unit MHz ns Low Time Tcl 10 - - ns Set up time Tds 5 - - ns Hold time Tdh 10 - - ns Cycle TH 30.00 31.78 - µs 770 800 900 clock Pulse width THp 2 96 200 clock Cycle TV 515 446 447 2 640 525 449 449 640 560 480 510 34 640 line line line line clock 480 400 350 all Pulse width Horizontal display period TVp THd HSYNC-Clock phase difference THc 10 - Tc-10 ns HSYNC.-VSYNC. phase difference TVh 0 - TH-THp clock Notes: 1. In case of lower frequency, deterioration of the display quality, flicker, etc. may occur. HORIZONTAL DISPLAY POSITION The horizontal display position is determined by ENAB signal and the input data corresponding to the rising edge ENAB signal is displayed at the left end of the active area. Parameter Set-up time Pulse width HSYNC-enable signal phase difference Enable signal Symbol Tes Tep THe MIN 5 2 44 TYP 640 - MAX Tc-10 640 TH-664 Unit ns clock clock Notes: 1. When ENAB is fixed at "Low", the display starts from the data of C104 (clock) as shown in Fig. 2-1~3. Be careful the module does not work when ENAB is fixed "High". White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 6 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division VERTICAL DISPLAY POSITION The vertical display position is automatically centered in the active area at each mode of VGA,480-,400-,and 350-line mode. Each mode is selected depending on the polarity of the synchronous signals described in Note 1 on page 2. In each mode, the data of TVn is displayed at the top line of the active area. The display position will be centered Mode V-data start (TVs) V-data Perioc (TVd) 480 34 400 34 350 61 ENH064V1-300/450 on the screen like the following figure when the period of vertical synchronous signal, TV, is typical value. In 400-,and 350-line mode, the data in the vertical data invalid period is also displayed. So, inputting all data “()” is recommended during vertical data invalid period. ENAB signal has no relation to the vertical display position. V-display Start (TVn) V-display Period Unit 480 34 480 line 400 443-TV 480 line 350 445-TV 480 lute data invalid period 4 0 lines 6 5 lines data invalid period data period data period 3 5 0 lines 4 0 0 lines data invalid period 4 0 lines 6 5 lines data invalid period 350 lines mode (TV=449) 400 lines mode (TV=449) INPUT DATA SIGNALS AND DISPLAY POSITION ON THE SCREEN Display position of input data (480 lines mode) UP D1, DH1 D2, DH1 D1, DH2 D2, DH2 D3, DH1 D640, DH1 D1, DH3 R G B R/L = OPEN U/D = OPEN D1, DH480 D640, DH480 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 7 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 Data signal (R0~R5, G0~G5 B0~B5) Horizontal sync. signal (Hsync) Vertical sync. signal (Vsync) Data enable signal (ENAB) Data signal (R0~R5, G0~G5 B0~B5) Clock signal (CK) Horizontal sync. signal (Hsync) 0.3Vcc THc TVh 0.3Vcc 1 2 TVp 0.7Vcc Tes TVs D1 D2 D3 Tep THd 0.3Vcc 0.7Vcc 0.3Vcc Tdh 0.7Vcc Tds Tc Tch Tc TH 34 D640 DH1 Number of line D639 DH2 0.3Vcc DH3 TVd Horizontal invalid data period Number of H-data Fig 2-1 Input signal waveforms (480 line mode) Vertical invalid data period 0.7Vcc THe Horizontal invalid data period 0.3Vcc 0.3Vcc C104* C2* Number of clock 0.7Vcc *Only when enable terminal is fixed "low" 0.3Vcc C1* 0.7Vcc 0.3Vcc 0.3Vcc THp TV DH479 DH480 0.3Vcc Number of V-data line Vertical invalid data period 0.3Vcc White Electronic Designs Display Systems Division ENH064V1-300/450 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 8 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 0.3Vcc Data signal (R0~R5, G0~G5, B0~B5) Horizontal sync. signal (Hsync) Vertical sync. signal (Vsync) Data enable signal (ENAB) Data signal (R0~R5, G0~G5, B0~B5) Clock signal (CK) Horizontal sync. signal (Hsync) THc C1* 0.7Vcc TVh 1 0.7Vcc 2 TVp 0.7Vcc D1 TVs Tes C104* D2 0.7Vcc 0.3Vcc THd 0.3Vcc 0.7Vcc 0.3Vcc Tep D3 Tds Tdh Tc Tch Tc TH 34 D640 DH1 Number of line D639 DH2 0.3Vcc DH3 TVd Horizontal invalid data period Number of H-data Fig. 2-2 Input signal waveforms (400 line mode) Vertical invalid data period THe 0.3Vcc Number of clock C2* 0.3Vcc *Only when enable terminal (ENAB) is fixed "Low" 0.3Vcc 0.7Vcc Horizontal invalid data period 0.3Vcc THp TV DH399 DH400 0.3Vcc Vertical invalid data period Number of V-data line 0.7Vcc White Electronic Designs Display Systems Division ENH064V1-300/450 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 9 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 Data signal (R0~R5, G0~G5, B0~B5) Horizontal sync. signal (Hsync) Vertical sync. signal (Vsync) Data enable signal (ENAB) Data signal (R0~R5, G0~G5, B0~B5) Clock signal (CK) (Hsync) Horizontal sync. signal 0.7Vcc 0.3Vcc THc C1* 0.3Vcc Number of clock TVh 0.3Vcc 2 TVp 0.7Vcc D1 Vertical invalid data period 0.3Vcc 1 THe C2* 0.3Vcc D2 0.7Vcc D3 0.3Vcc 0.7Vcc 0.3Vcc Tep THd Tdh 0.7Vcc Tds Tc Tch Tc 61 D640 DH1 Number of line D639 DH2 0.3Vcc DH3 TVd Horizontal invalid data period Number of H-data Fig 2-3 Input signal waveforms (350 line mode) TVs Tes C104* *Only when enable terminal (ENAB) fixed "low" 0.3Vcc Horizontal invalid data period THp 0.7Vcc TH TV DH349 DH350 0.7Vcc Number of V-data line Vertical invalid data period 0.3Vcc White Electronic Designs Display Systems Division ENH064V1-300/450 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 10 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH064V1-300/450 INPUT SIGNALS, BASIC DISPLAY COLORS AND GRAY SCALE OF EACH COLOR Gray Scale of Red Basic Color Colors & Grayscale Black Blue Green Cyan Red Magenta Yellow White Black Darker Brighter Gray Scale of Green Red Black Darker Brighter Gray Scale of Blue Green Black Darker Brighter Blue Data signal Gray Scale GS0 GS1 GS2 R0 0 0 0 0 1 1 1 1 0 1 0 R1 0 0 0 0 1 1 1 1 0 0 1 R2 0 0 0 0 1 1 1 1 0 0 0 R3 0 0 0 0 1 1 1 1 0 0 0 R4 0 0 0 0 1 1 1 1 0 0 0 R5 0 0 0 0 1 1 1 1 0 0 0 G0 0 0 1 1 0 0 1 1 0 0 0 G1 0 0 1 1 0 0 1 1 0 0 0 G2 0 0 1 1 0 0 1 1 0 0 0 G3 0 0 1 1 0 0 1 1 0 0 0 G4 0 0 1 1 0 0 1 1 0 0 0 G5 0 0 1 1 0 0 1 1 0 0 0 B0 0 1 0 1 0 1 0 1 0 0 0 B1 0 1 0 1 0 1 0 1 0 0 0 B2 0 1 0 1 0 1 0 1 0 0 0 B3 0 1 0 1 0 1 0 1 0 0 0 B4 0 1 0 1 0 1 0 1 0 0 0 B5 0 1 0 1 0 1 0 1 0 0 0 GS61 GS62 GS63 GS0 GS1 GS2 1 0 1 0 0 0 0 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS61 GS62 GS63 GS0 GS1 GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS61 GS62 GS63 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Notes: 1. 0: Low level voltage 1: High level voltage. 2. Each basic color can be displayed in 64 gray scales from 6 bit data signals. 3. According to the combination of total 18 bit data signals, the 262, 144-color display can be achieved on the screen. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 11 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH064V1-300/450 OPTICAL CHARACTERISTICS tA=25°C, VCC=+5V Viewing Angle Range Parameter Horizontal Vertical Contrast Ratio Response Time Rise Decay Luminance of White Chromaticity of White White Uniformity Viewing Angle Range as a Brightness Definition Horizontal Vertical Symbol θ21, θ22 Condition (CR>5) θ11 θ12 CR tr td YL x y δw θ21, θ22 θ11, θ12 Best Viewing Angle θ = 0° 50% of the maximum brightness Min 60 35 55 100 240 40,000 Typ 70 40 70 20 40 300 0.313 0.325 45 Max 1.45 - Unit Deg. Deg. Deg. ms ms cd/m2 Deg. Remarks (4) (2, 4) (3, 4) (4) (5) (1) Notes: 1. The measurements shall be executed 30 minutes after lighting at rating. (typical condition: IL=6mArms) The optical characteristics shall be measured in a dark room or equivalent state with the method shown in Fig. 3 below. Photodetector (BM-5A: TOPCON) Parameter Luminance of White IM Film IM, ELG Min. Typ. Max. Unit 240 320 300 450 - cd/m2 Field=2° 400mm TFT-LCD Module LCD Panel Center of the screen White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 12 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division Notes: 1. Definition of viewing angle range: ENH064V1-300/450 Normal line θ22 θ12 θ11 θ21 6 o'clock direction Definition of contrast ratio The contrast ratio is defined as follows: Contrast Ratio (CR)= 3. black white Luminance (brightness) with all pixels white Luminance (brightness) with all pixels black Definition of response time The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white". Photodetector output (Relative Value) 2. white 100% 90% 10% 0% τd τr time 160 4. 5. This shall be measured at the center of the screen. Definition of white uniformity: White uniformity is defined as the following with five measurements. 320 A (A~E). 480 pixel D C B δw= 120 240 E 360 pixel Maximum Luminance of five points (brightness) Minimum Luminance of five points (brightness) White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 13 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH064V1-300/450 HANDLING PRECAUTIONS 10. Laminated film is attached to the module surface to prevent it from being scratched . Before use, peel the film off slowly, with strict attention to electrostatic charges. Ionized air shall be blown over during the action. Blow off ‘dust’ on the polarizer by using an ionized nitrogen gun. 1. Be sure to turn off the power supply when inserting or disconnecting the cable. 11. Connect GND to 4 place of mounting holes to stabilize against EMI and external noise 2. Design the cabinet so that the module can be installed without any extra stress such as warp or twist. 12. The high voltage portions on the backlight are very dangerous. Careless handling may lead to electrical shock. DISPLAY QUALITY The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. 3. Since the front polarizer is easily damaged, pay attention to avoid rubbing with something hard or sharp. PACKING FORM 4. Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 1. Piling number of cartons : MAX 10 2. Package quantity in one carton: 20pcs 5. When the panel surface is soiled,use an absorbent cotton or other soft cloth to wipe it off. 3. Carton size: 355(W) X 282(D) X 265(H)mm 6. Since the panel is made of glass and refined wires and components, it may break,crack or internal wire breaking if dropped or bumped on hard surface. Handle with care. OTHERS 7. Since CMOS LSI is used in this module, make certain one is grounded when handling. 8. Observe all other precautionary requirements in handling components. 9. This module has its circuitry PCBs on the rear side and should be carefully handled in order to avoid being stressed. 4. Total mass of 1 carton filled with full modules : 7.0kg 1. Disassembling the module can cause permanent damage and should be avoided. 2. Image retention may occur when a fixed pattern is displayed for a long time. EXCHANGE OF LAMPS This must be action performed by Panelview. RELIABILITY TEST ITEMS No. 1 2 3 4 5 6 7 Test items High temperature storage test Low temperature storage test High temperature and high humidity operating test High temperature operating test Low temperature operating test Vibration Test (Non-operating) Shock test (non-operating) Conditions tA=70°C tA=-25°C tP=40°C, 95%RH (No condensation) tA=55°C tA=-0°C Frequency Sweep time Test Period Max gravity Pulse width Direction 240h 240h 240h 240h 240h :10~57Hz/Vibration width (one side): 0.075mm :58~500Hz/Gravity: 9.8m/s2 :11 minutes :3 hours (1 hour for each direction of X, Y, Z) :490m/s2 :11 minutes :±X, ±Y, ±Z (once for each direction.) White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 14 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH064V1-300/450 96.2 CNA 3. GND 1. HOT Active Area: 96.96 x 130.56 136.2 (Bezel Opening) Active Area Center CN1 122 108 73.4 100 (Bezel Opening) 69.4 (Bezel Opening) 144.2 126.5 1.5 175 122 2.1 ARROW SHOWS 6 O'CLOCK VIEWING ANGLE Front View 120 +10 -5 CNB 1. HOT 3. GND SEE DETAIL C 94 SEE DETAIL A SEE DETAIL B 12 170.5 7.4 4.2 Ø2.2 3 ENLARGED DETAIL B 1. TOLERANCE X-DIRECTION A:4x12±0x8 2. TOLERANCE X-DIRECTION B:1x52±0x8 3. TOLERANCE Y-DIRECTION C:1x52±0x8 4. TOLERANCE Y-DIRECTION D:1x52±0x8 5. OBLIQUITY OF DISPLAY AREA BEZEL FACE Full-R 4.5 4.5 ENLARGED DETAIL A 2.2 4.5 4.5 HEIGHT OF I/F PRINTED WIRING BOARD CN1 5 7.6 ENLARGED DETAIL C Notes: 1. Unspecified tolerance to be ±0.5. 2. Floating of PWB and chassis are excluded from module thickness. 3. Diameter of mounting boss shall be the range of 3.5mm to 4mm. (center of oval hole) IE-FI<0x8 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 15 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH064V1-300/450 91.2 10.7 No. 30 24.6 No. 31 CN1 23.4 (35.7) No. 1 No. 2 Note: 1. Unspecified tolerance to be ±0.5. 2. Floating of PWB and chassis are excluded from module thickness. 3. Diameter of mounting boss shall be range of 3.5mm to 4mm. (Center of oval hole) CONNECTOR OF I/F AND CIRCUMFERENCE DIAGRAM H=0 H=1mm Max (35.7) 24.6 10.8 10.7 (91.2) H=3.4mm HEIGHT STANDARD (H=0) IS PRINTED WIRING BOARD White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 16 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0