TI BQ2004H Fast-charge ic Datasheet

bq2004E/H
Fast-Charge ICs
Features
General Description
ture and voltage are within configured limits.
➤ Fast charge and conditioning of
nickel cadmium or nickel-metal
hydride batteries
The bq2004E and bq2004H Fast
Charge ICs provide comprehensive
fast charge control functions together
with high-speed switching power control circuitry on a monolithic CMOS
device.
Temperature, voltage, and time are
monitored throughout fast charge.
Fast charge is terminated by any of
the following:
➤ Hysteretic PWM switch-mode
current regulation or gated control of an external regulator
➤ Easily integrated into systems or
used as a stand-alone charger
➤ Pre-charge qualification of temperature and voltage
➤ Configurable, direct LED outputs
display battery and charge status
➤ Fast-charge termination by ∆ temperature/∆ time, peak volume detection, -∆V, maximum voltage,
maximum temperature, and maximum time
➤ O ption al t op -off charge and
pulsed current maintenance
charging
➤ Logic-level controlled low-power
mode (< 5µA standby current)
Pin Connections
Integration of closed-loop current
control circuitry allows the bq2004
to be the basis of a cost-effective solution for stand-alone and systemintegrated chargers for batteries of
one or more cells.
Switch-activated discharge-beforecharge allows bq2004E/H-based chargers to support battery conditioning
and capacity determination.
High-efficiency power conversion is
accomplished using the bq2004E/H as
a hysteretic PWM controller for
switch-mode regulation of the charging current. The bq2004E/H may alternatively be used to gate an externally regulated charging current.
Fast charge may begin on application
of the charging supply, replacement
of the battery, or switch depression.
For safety, fast charge is inhibited
unless/until the battery tempera-
Rate of temperature rise
(∆T/∆t)
n
Peak voltage detection (PVD)
n
Negative delta voltage (-∆V)
n
Maximum voltage
n
Maximum temperature
n
Maximum time
After fast charge, optional top-off
and pulsed current maintenance
phases with appropriate display
mode selections are available.
The bq2004H diffe r s fr o m the
bq2004E only in that fast charge,
hold-off, and top-off time units have
been scaled up by a factor of two,
and the bq2004H provides different
display selections. Timing differences between the two ICs are illustrated in Table 1. Display differences are shown in Table 2.
Pin Names
DCMD
Discharge command
SNS
Sense resistor input
DSEL
Display select
LED1
Charge status output 1
VSEL
Voltage termination
select
LED2
Charge status output 2
VSS
System ground
VCC
5.0V ± 10% power
MOD
Charge current control
DIS
Discharge control
output
INH
Charge inhibit input
DCMD
1
16
INH
DSEL
2
15
DIS
VSEL
3
14
MOD
TM1
4
13
VCC
TM1
Timer mode select 1
TM2
5
12
VSS
TM2
Timer mode select 2
TCO
6
11
LED2
TCO
Temperature cutoff
TS
7
10
LED1
BAT
8
9
SNS
TS
Temperature sense
BAT
Battery voltage
16-Pin Narrow DIP
or Narrow SOIC
n
PN2004E01.eps
SLUS081 - JUNE 1999
1
bq2004E/H
SNS
Pin Descriptions
DCMD
SNS controls the switching of MOD based on
an external sense resistor in the current
path of the battery. SNS is the reference potential for both the TS and BAT pins. If
SNS is connected to VSS, then MOD switches
high at the beginning of charge and low at
the end of charge.
Discharge-before-charge control input
The DCMD input controls the conditions
that enable discharge-before-charge. DCMD
is pulled up internally. A negative-going
pulse on DCMD initiates a discharge to endof-discharge voltage (EDV) on the BAT pin,
followed by a new charge cycle start. Tying
DC MD to ground enables auto matic
discharge-before-charge on every new charge
cycle start.
DSEL
LED1–
LED2
Display select input
Vss
Ground
This three-state input configures the charge
status display mode of the LED1 and LED2 outputs and can be used to disable top-off and
pulsed-trickle. See Table 2.
VCC
VCC supply input
5.0V, ±10% power input.
MOD is a push-pull output that is used to
control the charging current to the battery.
MOD switches high to enable charging current to flow and low to inhibit charging
current flow.
DIS
Timer mode inputs
INH
Temperature sense input
Input, referenced to SNS, for an external
thermister monitoring battery temperature.
BAT
Charge inhibit input
When low, the bq2004E/H suspends all
charge actions, drives all outputs to high impedance, and assumes a low-power operational state. When transitioning from low to
high, a new charge cycle is started.
Temperature cut-off threshold input
Input to set maximum allowable battery
temperature. If the potential between TS
and SNS is less than the voltage at the TCO
input, then fast charge or top-off charge is terminated.
TS
Discharge control output
Push-pull output used to control an external
transistor to discharge the battery before
charging.
TM1 and TM2 are three-state inputs that
configure the fast charge safety timer, voltage
termination hold-off time, “top-off ”, and
trickle charge control. See Table 1.
TCO
Charge current control output
Voltage termination select input
This three-state input controls the voltageterm inat ion technique used by the
bq2004E/H. When high, PVD is active.
When floating, -∆V is used. When pulled low,
both PVD and -∆V are disabled.
TM1–
TM2
Charge status outputs
Push-pull outputs indicating charging
status. See Table 2.
MOD
VSEL
Charging current sense input
Battery voltage input
BAT is the battery voltage sense input, referenced to SNS. This is created by a highimpedance resistor-divider network connected between the positive and the negative
terminals of the battery.
2
bq2004E/H
Functional Description
Discharge-Before-Charge
Figure 2 shows a block diagram and Figure 3 shows a
state diagram of the bq2004E/H.
The DCMD input is used to command discharge-beforecharge via the DIS output. Once activated, DIS becomes
active (high) until VCELL falls below VEDV, at which time
DIS goes low and a new fast charge cycle begins.
Battery Voltage and Temperature
Measurements
The DCMD input is internally pulled up to VCC (its inactive state). Leaving the input unconnected, therefore,
results in disabling discharge-before-charge. A negative
going pulse on DCMD initiates discharge-before-charge
at any time regardless of the current state of the
bq2004. If DCMD is tied to VSS, discharge-before-charge
will be the first step in all newly started charge cycles.
Battery voltage and temperature are monitored for
maximum allowable values. The voltage presented on
the battery sense input, BAT, should represent a
two-cell potential for the battery under charge. A
resistor-divider ratio of:
RB1 N
=
-1
RB2 2
Starting A Charge Cycle
is recommended to maintain the battery voltage within
the valid range, where N is the number of cells, RB1 is
the resistor connected to the positive battery terminal,
and RB2 is the resistor connected to the negative battery terminal. See Figure 1.
A new charge cycle is started by:
1.
Application of VCC power.
2.
VCELL falling through the maximum cell voltage,
VMCV where:
Note: This resistor-divider network input impedance to
end-to-end should be at least 200kΩ and less than 1MΩ.
VMCV = 0.8 ∗ VCC ± 30mV
3.
A ground-referenced negative temperature coefficient thermistor placed in proximity to the battery may be used as a
low-cost temperature-to-voltage transducer. The temperature sense voltage input at TS is developed using a
resistor-thermistor network between VCC and VSS. See
Figure 1. Both the BAT and TS inputs are referenced to
SNS, so the signals used inside the IC are:
A transition on the INH input from low to high.
If DCMD is tied low, a discharge-before-charge will be
executed as the first step of the new charge cycle. Otherwise, pre-charge qualification testing will be the first
step.
The battery must be within the configured temperature
and voltage limits before fast charging begins.
VBAT - VSNS = VCELL
and
The valid battery voltage range is VEDV < VBAT < VMCV
where:
VTS - VSNS = VTEMP
VEDV = 0.4 ∗ VCC ± 30mV
Negative Temperature
Coefficient Thermister
VCC
PACK +
RT1
PACK+
bq2004E/H
TS
RB1
bq2004E/H
BAT
RB2
SNS
RT2
SNS
PACK-
N
T
C
PACK -
Fg2004a.eps
Figure 1. Voltage and Temperature Monitoring
3
bq2004E/H
TM1 TM2
TCO
Timing
Control
TCO
Check
OSC
LED1
LED2
DSEL
TS
LTF
Check
Display
Control
VTS - VSNS
DCMD
DVEN
VBAT - VSNS
Charge Control
State Machine
A/D
SNS
EDV
Check
Discharge
Control
MOD
Control
PWR
Control
DIS
MOD
INH
MCV
Check
BAT
VCC VSS
BD200401.eps
Figure 2. Block Diagram
Fast charge continues until termination by one or more
of the six possible termination conditions:
The valid temperature range is VHTF < VTEMP < VLTF,
where:
VLTF = 0.4 ∗ VCC ± 30mV
n
Delta temperature/delta time (∆T/∆t)
VHTF = [(1/3 ∗ VLTF) + (2/3 ∗ VTCO)] ± 30mV
n
Peak voltage detection (PVD)
n
Negative delta voltage (-∆V)
n
Maximum voltage
n
Maximum temperature
n
Maximum time
VTCO is the voltage presented at the TCO input pin, and is
configured by the user with a resistor divider between VCC
and ground. The allowed range is 0.2 to 0.4 ∗ VCC.
If the temperature of the battery is out of range, or the
voltage is too low, the chip enters the charge pending
state and waits for both conditions to fall within their allowed limits. During the charge-pending mode, the IC
first applies a top-off charge to the battery.
PVD and -∆V Termination
The bq2004E/H samples the voltage at the BAT pin once
every 34s. When -∆V termination is selected, if VCELL is
lower than any previously measured value by 12mV
±4mV (6mV/cell), fast charge is terminated. When PVD
termination is selected, if VCELL is lower than any previously measured value by 6mV ±2mV (3mV/cell), fast
charge is terminated. The PVD and -∆V tests are valid
in the range 0.4 ∗ VCC < VCELL < 0.8 ∗ VCC.
The top-off charge, at the rate of 1 8 of the fast charge,
continues until the fast-charge conditions are met or the
top-off time-out period is exceeded. The IC then trickle
charges until the fast-charge conditions are met. There
is no time limit on the charge pending state; the charger
remains in this state as long as the voltage or temperature conditons are outside of the allowed limits. If the
voltage is too high, the chip goes to the battery absent
state and waits until a new charge cycle is started.
4
bq2004E/H
VSEL Input
Low
Float
High
∆T/∆t Termination
Voltage Termination
Disabled
The bq2004E/H samples at the voltage at the TS pin
every 34s, and compares it to the value measured two
samples earlier. If VTEMP has fallen 16mV ±4mV or
more, fast charge is terminated. The ∆T/∆t termination
test is valid only when VTCO < VTEMP < VLTF.
-∆V
PVD
Voltage Sampling
Temperature Sampling
Each sample is an average of voltage measurements.
The IC takes 32 measurements in PVD mode and 16
measurements in -∆V mode. The resulting sample periods (9.17ms and 18.18ms, respectively) filter out harmonics centered around 55Hz and 109Hz. This technique minimizes the effect of any AC line ripple that
may feed through the power supply from either 50Hz or
60Hz AC sources. Tolerance on all timing is ±16%.
Each sample is an average of 16 voltage measurements.
The resulting sample period (18.18ms) filters out harmonics around 55Hz. This technique minimizes the effect of any AC line ripple that may feed through the
power supply from either 50Hz or 60Hz AC sources. Tolerance on all timing is ±16%.
Maximum Voltage, Temperature, and Time
Temperature and Voltage Termination
Hold-off
Anytime VCELL rises above VMCV, the LEDs go off and current flow into the battery ceases immediately. If VCELL
then falls back below VMCV before tMCV = 1.5s ±0.5s, the
chip transitions to the Charge Complete state (maximum
voltage termination). If VCELL remains above VMCV at the
expiration of tMCV, the bq2004E/H transitions to the Battery Absent state (battery removal). See Figure 3.
A hold-off period occurs at the start of fast charging.
During the hold-off period, -∆V and ∆T/∆t termination
are disabled. The MOD pin is enabled at a duty cycle of
260µs active for every 1820µs inactive. This modulation
results in an average rate 1/8th that of the fast charge
rate. This avoids premature termination on the voltage
spikes sometimes produced by older batteries when
fast-charge current is first applied. Maximum voltage
and maximum temperature terminations are not affected by the hold-off period.
Maximum temperature termination occurs anytime
V TEMP falls below the temperature cutoff threshold
VTCO. Charge will also be terminated if VTEMP rises
above the low temperature fault threshold, VLTF, after
fast charge begins.
Table 1. Fast Charge Safety Time/Hold-Off/Top-Off Table
Typical
Fast-Charge
Safety
Time (min)
Corresponding
Fast-Charge
Rate
2004E
2004H
TM1
TM2
Typical
PVD, -∆V
Hold-Off
Time (s)
2004E
2004H
2004E
Top-Off
Rate
2004H 2004E
2004H
PulseTrickle
Rate
PulseTrickle
Period (Hz)
2004E
2004H
C/4
C/8
Low
Low
325
650
137
273
Disabled
Disabled
C/2
C/4
Float
Low
154
325
546
546
Disabled
C/512
1C
C/2
High
Low
77
154
273
546
Disabled
C/512
7.5
15
2C
1C
Low
Float
39
77
137
273
Disabled
C/512
3.75
7.5
4C
2C
Float
Float
19
39
68
137
Disabled
C/512
1.88
3.75
C/2
C/4
High
Float
154
325
546
546
C/16
C/32
C/512
15
30
1C
C/2
Low
High
77
154
273
546
C/8
C/16
C/512
7.5
15
2C
1C
Float
High
39
77
137
273
C/4
C/18
C/512
3.75
7.5
4C
2C
High
High
19
39
68
137
C/2
C/4
C/512
1.88
3.75
Note: Typical conditions = 25°C, VCC = 5.0V.
5
Disabled
15
30
bq2004E/H
Table 2. bq2004E/H LED Output Summary
Mode 1
bq2004E
DSEL = VSS
Charge Action State
LED1
LED2
Battery absent
Low
Low
Fast charge pending or a discharge-before-charge in progress
High
High
Fast charging
Low
High
Fast charge complete, top-off, and/or trickle
High
Low
LED1
LED2
Mode 1
bq2004H
DSEL = VSS
Charge Action State
Battery absent
Low
Low
Discharge-before-charge in progress
High
High
Fast charge pending
Low
Fast charging
Low
High
Fast charge complete, top-off, and/or trickle
High
Low
LED1
LED2
Battery absent
Low
Low
Fast charge pending or discharge-before-charge in progress
High
High
Fast charging
Low
High
Fast charge complete, top-off, and/or trickle
High
Low
LED1
LED2
Mode 2
bq2004E
Charge Action State (See note)
1
second high
second low
8
1
8
DSEL = Floating
Mode 2
bq2004H
Charge Action State (See note)
Battery absent
Low
Low
Discharge-before-charge in progress
High
High
DSEL = Floating Fast charge pending
Note:
1
second high
second low
8
1
8
Fast charging
Low
High
Fast charge complete, top-off, and/or trickle
High
Low
Mode 3
bq2004E/H
DSEL = VCC
Low
LED1
LED2
Battery absent
Charge Action State
Low
Low
Fast charge pending or discharge-before-charge in progress
Low
Fast charging
Low
High
Fast charge complete, top-off, and/or trickle
High
Low
Pulse trickle is inhibited in Mode 2.
6
1
8
1
8
second high
second low
bq2004E/H
Maximum charge time is configured using the TM pin.
Time settings are available for corresponding charge
rates of C/4, C/2, 1C, and 2C. Maximum time-out termination is enforced on the fast-charge phase, then reset,
and enforced again on the top-off phase, if selected.
There is no time limit on the trickle-charge phase.
Charge Current Control
Top-off Charge
When used in switch mode configuration, the nominal
regulated current is:
The bq2004E/H controls charge current through the MOD
output pin. The current control circuitry is designed to support implementation of a constant-current switching regulator
or to gate an externally regulated current source.
An optional top-off charge phase may be selected to
follow fast charge termination for the C/2 through 4C
rates. This phase may be necessary on NiMH or other
battery chemistries that have a tendency to terminate
charge prior to reaching full capacity. With top-off enabled, charging continues at a reduced rate after
fast-charge termination for a period of time equal to
0.235∗ the fast-charge safety time (See Table 1.) During top-off, the MOD pin is enabled at a duty cycle of
260µs active for every 1820µs inactive. This modulation results in an average rate 1/8th that of the fast
charge rate. Maximum voltage, time, and temperature
are the only termination methods enabled during topoff.
IREG = 0.225V/RSNS
Charge current is monitored at the SNS input by the
voltage drop across a sense resistor, RSNS, between the
low side of the battery pack and ground. RSNS is sized to
provide the desired fast charge current.
If the voltage at the SNS pin is less than VSNSLO, the
MOD output is switched high to pass charge current to
the battery.
When the SNS voltage is greater than VSNSHI, the MOD
output is switched low—shutting off charging current to
the battery.
VSNSLO = 0.04 ∗ VCC ± 25mV
Pulse-Trickle Charge
VSNSHI = 0.05 ∗ VCC ± 25mV
Pulse-trickle charging may be configured to follow the
fast charge and optional top-off charge phases to compensate for self-discharge of the battery while it is idle
in the charger.
When used to gate an externally regulated current
source, the SNS pin is connected to VSS, and no sense resisitor is required.
In the pulse-trickle mode, MOD is active for 260µs of a
period specified by the settings of TM1 and TM2. See
Table 1. The resulting trickle-charge rate is C/512.
Both pulse trickle and top-off may be disabled by tying
TM1 and TM2 to VSS or by selecting Mode 2 in the display.
Charge Status Indication
Charge status is indicated by the LED1 and LED2 outputs. The state of these outputs in the various charge cycle phases is given in Table 2 and illustrated in Figure 3.
In all cases, if VCELL exceeds the voltage at the MCV
pin, both LED1 and LED2 outputs are held low regardless of other conditions. Both can be used to directly
drive an LED.
7
bq2004E/H
New Charge Cycle Started by
Any One of:
Falling Edge
on DCMD
VCC Rising to Valid Level
Yes
Battery Replacement
(VCELL Falling through VMCV)
DCMD Tied to Ground?
Inhibit (INH) Released
No
VEDV < VCELL < VMCV
Charge
Pending
VCELL < VEDV
Battery Voltage?
VCELL < VEDV
VTEMP > VLTF or
VTEMP < VHTF
Top-Off and
Pulse-Trickle
Charge
Battery Temperature?
DischargeBefore-Charge
VCELL > VMCV
VCELL > VMCV
VCELL >
VMCV
VHTF < VTEMP < VLTF
Battery
Absent
VEDV < VCELL < VMCV
and
VHTF < VTEMP < VLTF
Fast
Charge
VCELL > VMCV
- V or
T/ t or
VTEMP < VTCO
or
Maximum Time Out
Top-Off
Selected?
Pulse
Trickle
Charge
t > tMCV
Pulse
Trickle
Charge
VCELL <
VMCV
VCELL >
VMCV
Top-Off
Charge
Yes
VTEMP < VTCO
or 0.235 Maximum
Time Out
No
Charge
Complete
VCELL >
VMCV
Pulse
Trickle
Charge
SD2004EH.eps
Figure 3. Charge Algorithm State Diagram
8
bq2004E/H
Absolute Maximum Ratings
Symbol
Parameter
Minimum
Maximum
Unit
VCC
VCC relative to VSS
-0.3
+7.0
V
VT
DC voltage applied on any pin excluding VCC relative to VSS
-0.3
+7.0
V
TOPR
Operating ambient temperature
-20
+70
°C
TSTG
Storage temperature
-55
+125
°C
TSOLDER
Soldering temperature
-
+260
°C
TBIAS
Temperature under bias
-40
+85
°C
Note:
Symbol
VSNSLO
Commercial
10 sec max.
Permanent device damage may occur if Absolute Maximum Ratings are exceeded. Functional operation should be limited to the Recommended DC Operating Conditions detailed in this data sheet. Exposure to conditions beyond the operational limits for extended periods of time may affect device reliability.
DC Thresholds
VSNSHI
Notes
(TA = TOPR; VCC ± 10%)
Parameter
High threshold at SNS resulting in MOD = Low
Low threshold at SNS resulting in MOD = High
Rating
Tolerance
Unit
0.05 * VCC
±0.025
V
0.04 * VCC
±0.010
V
Notes
VTEMP ≥ VLTF inhibits/terminates charge
VLTF
Low-temperature fault
0.4 * VCC
±0.030
V
VHTF
High-temperature fault
(1/3 * VLTF) + (2/3 * VTCO)
±0.030
V
VEDV
End-of-discharge voltage
0.4 * VCC
±0.030
V
VMCV
Maximum cell voltage
0.8 * VCC
±0.030
V
VTHERM
TS input change for∆T/∆t
detection
-16
±4
mV
VCC = 5V, TA = 25°C
-12
±4
mV
VCC = 5V, TA = 25°C
-6
±2
mV
VCC = 5V, TA = 25°C
-∆V
PVD
BAT input change for -∆V
detection
BAT input change for PVD
detection
9
VTEMP ≤ VHTF inhibits
charge
VCELL < VEDV inhibits
fast charge
VCELL > VMCV inhibits/
terminates charge
bq2004E/H
Recommended DC Operating Conditions (TA = TOPR)
Symbol
Condition
Minimum
Typical
Maximum
Unit
Notes
VCC
Supply voltage
4.5
5.0
5.5
V
VBAT
Battery input
0
-
VCC
V
VCELL
BAT voltage potential
0
-
VCC
V
VTS
Thermistor input
0
-
VCC
V
VTEMP
TS voltage potential
0
-
VCC
V
VTS - VSNS
VTCO
Temperature cutoff
0.2 * VCC
-
0.4 * VCC
V
Valid ∆T/∆t range
Logic input high
2.0
-
-
V
DCMD, INH
Logic input high
VCC - 0.3
-
-
V
TM1, TM2, DSEL, VSEL
Logic input low
-
-
0.8
V
DCMD, INH
Logic input low
-
-
0.3
V
TM1, TM2, DSEL, VSEL
VBAT - VSNS
VIH
VIL
VOH
Logic output high
VCC - 0.8
-
-
V
DIS, MOD, LED1, LED2,
IOH ≤ -10mA
VOL
Logic output low
-
-
0.8
V
DIS, MOD, LED1, LED2,
IOL ≤ 10mA
ICC
Supply current
-
1
3
mA
Outputs unloaded
ISB
Standby current
-
-
1
µA
INH = VIL
IOH
DIS, LED1, LED2, MOD source
-10
-
-
mA
@VOH = VCC - 0.8V
IOL
DIS, LED1, LED2, MOD sink
10
-
-
mA
@VOL = VSS + 0.8V
Input leakage
-
-
±1
µA
INH, BAT, V = VSS to VCC
Input leakage
50
-
400
µA
DCMD, V = VSS to VCC
IL
IIL
Logic input low source
-
-
70
µA
TM1, TM2, DSEL, VSEL,
V = VSS to VSS + 0.3V
IIH
Logic input high source
-70
-
-
µA
TM1, TM2, DSEL, VSEL,
V = VCC - 0.3V to VCC
IIZ
Tri-state
-2
-
2
µA
TM1, TM2, DSEL, and VSEL
should be left disconnected
(floating) for Z logic input state
Note:
All voltages relative to VSS except as noted.
10
bq2004E/H
Impedance
Symbol
Parameter
Minimum
Typical
Maximum
Unit
RBAT
Battery input impedance
50
-
-
MΩ
RTS
TS input impedance
50
-
-
MΩ
RTCO
TCO input impedance
50
-
-
MΩ
RSNS
SNS input impedance
50
-
-
MΩ
Timing
Symbol
(TA = 0 to +70°C; VCC ± 10%)
Parameter
tPW
Pulse width for DCMD
and INH pulse command
dFCV
Time base variation
fREG
Minimum Typical
Maximum
Unit
Notes
1
-
-
µs
Pulse start for charge or discharge
before charge
-16
-
16
%
VCC = 4.75V to 5.25V
MOD output regulation
frequency
-
-
300
kHz
tMCV
Maximum voltage termination time limit
1
-
2
s
Note:
Typical is at TA = 25°C, VCC = 5.0V.
11
Time limit to distinguish battery removed from charge complete.
bq2004E/H
16-Pin DIP Narrow (PN)
16-Pin PN (0.300" DIP)
Inches
12
Millimeters
Dimension
Min.
Max.
Min.
Max.
A
0.160
0.180
4.06
4.57
A1
0.015
0.040
0.38
1.02
B
0.015
0.022
0.38
0.56
B1
0.055
0.065
1.40
1.65
C
0.008
0.013
0.20
0.33
D
0.740
0.770
18.80
19.56
E
0.300
0.325
7.62
8.26
E1
0.230
0.280
5.84
7.11
e
0.300
0.370
7.62
9.40
G
0.090
0.110
2.29
2.79
L
0.115
0.150
2.92
3.81
S
0.020
0.040
0.51
1.02
bq2004E/H
16-Pin SOIC Narrow (SN)
16-Pin SN (0.150" SOIC)
Inches
D
e
B
E
H
A
C
A1
.004
L
13
Millimeters
Dimension
Min.
Max.
Min.
Max.
A
0.060
0.070
1.52
1.78
A1
0.004
0.010
0.10
0.25
B
0.013
0.020
0.33
0.51
C
0.007
0.010
0.18
0.25
D
0.385
0.400
9.78
10.16
E
0.150
0.160
3.81
4.06
e
0.045
0.055
1.14
1.40
H
0.225
0.245
5.72
6.22
L
0.015
0.035
0.38
0.89
bq2004E/H
Data Sheet Revision History
Change No.
Page No.
1
All
2
3
Description
Nature of Change
Combined bq2004E and bq2004H, revised and
expanded format of this data sheet
Clarification
7
Separated bq2004E and bq2004H in Table 2, LED
Output Summary
Clarification
5
Description of charge-pending state
Clarification
4
Note:
Change 1 = Oct. 1997 B changes from Sept. 1996 (bq2004E), Feb. 1997 (bq2004H).
Change 2 = Feb. 1998 C changes from Oct. 1997 B.
Change 3 = Dec. 1998 D changes from Feb. 1998 C.
Change 4 = June 1999 E changes from Dec. 1998 D.
14
bq2004E/H
Ordering Information
bq2004
Package Option:
PN = 16-pin narrow plastic DIP
SN = 16-pin narrow SOIC
Device:
E = bq2004E Fast-Charge IC
H= bq2004H Fast-Charge IC
15
PACKAGE OPTION ADDENDUM
www.ti.com
23-May-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
BQ2004EPN
ACTIVE
PDIP
N
16
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
BQ2004EPNG4
ACTIVE
PDIP
N
16
25
Green (RoHS &
no Sb/Br)
CU NIPDAU
N / A for Pkg Type
BQ2004ESN
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BQ2004ESNG4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BQ2004ESNTR
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BQ2004ESNTRG4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BQ2004HPN
ACTIVE
PDIP
N
16
25
TBD
CU NIPDAU
N / A for Pkg Type
BQ2004HSN
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BQ2004HSNG4
ACTIVE
SOIC
D
16
40
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BQ2004HSNTR
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
BQ2004HSNTRG4
ACTIVE
SOIC
D
16
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-May-2007
TAPE AND REEL INFORMATION
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
23-May-2007
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
BQ2004ESNTR
D
16
TAI
330
16
6.5
10.3
2.5
8
16
Q1
BQ2004HSNTR
D
16
TAI
330
16
6.5
10.3
2.5
8
16
Q1
TAPE AND REEL BOX INFORMATION
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
BQ2004ESNTR
D
16
TAI
346.0
346.0
33.0
BQ2004HSNTR
D
16
TAI
346.0
346.0
33.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated