CYW4356 ADVANCE Single-Chip 5G WiFi IEEE 802.11ac 2×2 MAC/ Baseband/Radio with Integrated Bluetooth 4.1, FM Receiver, and Wireless Charging The Cypress CYW4356 is a complete dual-band (2.4 GHz and 5 GHz) 5G WiFi 2 × 2 MIMO MAC/PHY/Radio System-on-a-Chip. This Wi-Fi single-chip device provides a high level of integration with dual-stream IEEE 802.11ac MAC/baseband/radio, Bluetooth 4.1, and FM radio receiver. Additionally, it supports wireless charging. In IEEE 802.11ac mode, the WLAN operation supports rates of MCS0– MCS9 (up to 256 QAM) in 20 MHz, 40 MHz, and 80 MHz channels for data rates up to 867 Mbps. In addition, all the rates specified in IEEE 802.11a/b/g/n are supported. Included on-chip are 2.4 GHz and 5 GHz transmit power amplifiers and receive low noise amplifiers. For the WLAN section, several alternative host interface options are included: an SDIO v3.0 interface that can operate in 4b or 1b modes, and a PCIe v3.0 compliant interface running at Gen1 speeds. For the Bluetooth section, host interface options of a high-speed 4-wire UART and USB 2.0 full-speed (12 Mbps) are provided. The CYW4356 uses advanced design techniques and process technology to reduce active and idle power, and includes an embedded power management unit that simplifies the system power topology. In addition, the CYW4356 implements highly sophisticated enhanced collaborative coexistence hardware mechanisms and algorithms that ensure that WLAN and Bluetooth collaboration is optimized for maximum performance. Coexistence support for external radios (such as LTE cellular and GPS) is provided via an external interface. As a result, enhanced overall quality for simultaneous voice, video, and data transmission on a handheld system is achieved. This data sheet provides details on the functional, operational, and electrical characteristics for the Cypress CYW4356. It is intended for hardware design, application, and OEM engineers. Cypress Part Numbering Scheme Cypress is converting the acquired IoT part numbers from Broadcom to the Cypress part numbering scheme. Due to this conversion, there is no change in form, fit, or function as a result of offering the device with Cypress part number marking. The table provides Cypress ordering part number that matches an existing IoT part number. Table 1. Mapping Table for Part Number between Broadcom and Cypress Broadcom Part Number Cypress Part Number BCM4356 CYW4356 BCM4330 CYW4330 BCM4356XKUBG CYW4356XKUBG BCM4356XKWBG CYW4356XKWBG Cypress Semiconductor Corporation Document Number: 002-15053 Rev. *D • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised Monday, November 14, 2016 ADVANCE CYW4356 Figure 1. Functional Block Diagram ‘ VIO VBAT WL_REG_ON WLAN Host I/F PCIe SDIO 5G WLAN T/R Switch Ant1 Diplexer External Coexistence I/F COEX 2G WLAN T/R Switch 5G WLAN T/R Switch CLK_REQ BT_REG_ON CYW4356 USB 2.0 Bluetooth Host I/F FM Rx Host I/F Ant0 Diplexer UART 2G WLAN Tx I2S 2.G WL/BT Rx PCM 3PST Switch BT_DEV_WAKE BT Tx BT_HOST_WAKE FM Rx FM Audio Out FM I/F I2S Features IEEE 802.11X Key Features ■ IEEE 802.11ac Draft compliant. ■ ■ Dual-stream spatial multiplexing up to 867 Mbps data rate. Internal fractional nPLL allows support for a wide range of reference clock frequencies. ■ Supports IEEE 802.15.2 external coexistence interface to optimize bandwidth utilization with other co-located wireless technologies such as LTE or GPS. ■ Supports standard SDIO v3.0 (up to SDR104 mode at 208 MHz, 4-bit and 1-bit) host interfaces. ■ Backward compatible with SDIO v2.0 host interfaces. ■ PCIe mode complies with PCI Express base specification revision 3.0 for ×1 lane and power management running at Gen1 speeds. ■ Supports Active State Power Management (ASPM). ■ Integrated ARMCR4 processor with tightly coupled memory for complete WLAN subsystem functionality, minimizing the need to wake up the applications processor for standard WLAN functions. This allows for further minimization of power consumption, while maintaining the ability to field upgrade with future features. On-chip memory includes 768 KB SRAM and 640 KB ROM. ■ Supports 20, 40, and 80 MHz channels with optional SGI (256 QAM modulation). ■ Full IEEE 802.11a/b/g/n legacy compatibility with enhanced performance. ■ TX and RX low-density parity check (LDPC) support for improved range and power efficiency. ■ Supports IEEE 802.11ac/n beamforming. ■ On-chip power amplifiers and low-noise amplifiers for both bands. ■ Supports various RF front-end architectures including: ❐ Two antennas with one each dedicated to Bluetooth and WLAN. ❐ Two antennas with WLAN diversity and a shared Bluetooth antenna. ■ Shared Bluetooth and WLAN receive signal path eliminates the need for an external power splitter while maintaining excellent sensitivity for both Bluetooth and WLAN. ■ ■ Document Number: 002-15053 Rev. *D OneDriver™ software architecture for easy migration from existing embedded WLAN and Bluetooth devices as well as future devices. Supports A4WP wireless charging with the BCM59350. Page 2 of 155 ADVANCE Bluetooth and FM Key Features CYW4356 General Features ■ Complies with Bluetooth Core Specification Version 4.1 with provisions for supporting future specifications. ■ Supports battery range from 3.0V to 5.25V supplies with internal switching regulator ■ Bluetooth Class 1 or Class 2 transmitter operation. ■ Programmable dynamic power management ■ Supports extended synchronous connections (eSCO), for enhanced voice quality by allowing for retransmission of dropped packets. ■ 484 bytes of user-accessible OTP for storing board parameters Adaptive frequency hopping (AFH) for reducing radio frequency interference. ■ GPIOs: 11 in WLBGA, 16 in WLCSP ■ ■ ■ Interface support, host controller interface (HCI) using a USB or high-speed UART interface and PCM for audio data. Package options: ❐ 192-ball WLBGA (4.87 mm × 7.67 mm, 0.4 mm pitch ❐ 395-bump WLCSP (4.87 mm × 7.67 mm, 0.2 mm pitch) ■ USB 2.0 full-speed (12 Mbps) supported for Bluetooth. ■ ■ The FM unit supports HCI for communication. ■ Low power consumption improves battery life of handheld devices. ■ FM receiver: 65 MHz to 108 MHz FM bands; supports the European radio data systems (RDS) and the North American radio broadcast data system (RBDS) standards. Security: ❐ WPA and WPA2 (Personal) support for powerful encryption and authentication ❐ AES and TKIP in hardware for faster data encryption and IEEE 802.11i compatibility ❐ Reference WLAN subsystem provides Cisco Compatible Extensions (CCX, CCX 2.0, CCX 3.0, CCX 4.0, CCX 5.0) ❐ Reference WLAN subsystem provides Wi-Fi Protected Setup (WPS) ■ Supports multiple simultaneous Advanced Audio Distribution Profiles (A2DP) for stereo sound. ■ Worldwide regulatory support: Global products supported with worldwide homologated design. ■ Automatic frequency detection for standard crystal and TCXO values. Document Number: 002-15053 Rev. *D Page 3 of 155 ADVANCE CYW4356 Contents 1. Overview ........................................................................ 6 1.1 Overview ............................................................... 6 1.2 Features ................................................................ 8 1.3 Standards Compliance .......................................... 9 2. Power Supplies and Power Management ................. 10 2.1 Power Supply Topology ...................................... 10 2.2 CYW4356 PMU Features .................................... 10 2.3 WLAN Power Management ................................. 12 2.4 PMU Sequencing ................................................ 12 2.5 Power-Off Shutdown ........................................... 13 2.6 Power-Up/Power-Down/Reset Circuits ............... 13 2.7 Wireless Charging ............................................... 13 3. Frequency References ............................................... 16 3.1 Crystal Interface and Clock Generation .............. 16 3.2 External Frequency Reference ............................ 16 3.3 External 32.768 kHz Low-Power Oscillator ......... 18 4. Bluetooth + FM Subsystem Overview ...................... 19 4.1 Features .............................................................. 19 4.2 Bluetooth Radio ................................................... 20 5. Bluetooth Baseband Core ......................................... 22 5.1 Bluetooth 4.1 Features ........................................ 22 5.2 Bluetooth Low Energy ......................................... 22 5.3 Link Control Layer ............................................... 22 5.4 Test Mode Support .............................................. 23 5.5 Bluetooth Power Management Unit ..................... 23 5.6 Adaptive Frequency Hopping .............................. 26 5.7 Advanced Bluetooth/WLAN Coexistence ............ 26 5.8 Fast Connection (Interlaced Page and Inquiry Scans) ................................................................. 26 6. Microprocessor and Memory Unit for Bluetooth ..... 27 6.1 RAM, ROM, and Patch Memory .......................... 27 6.2 Reset ................................................................... 27 7. Bluetooth Peripheral Transport Unit ........................ 28 7.1 SPI Interface ........................................................ 28 7.2 SPI/UART Transport Detection ........................... 28 7.3 PCM Interface ..................................................... 28 7.4 USB Interface ...................................................... 36 7.5 UART Interface .................................................... 38 7.6 I2S Interface ........................................................ 39 8. FM Receiver Subsystem ............................................ 42 8.1 FM Radio ............................................................. 42 8.2 Digital FM Audio Interfaces ................................. 42 8.3 FM Over Bluetooth .............................................. 42 8.4 eSCO ................................................................... 42 8.5 Wideband Speech Link ....................................... 42 8.6 A2DP ................................................................... 42 8.7 Autotune and Search Algorithms ......................... 42 8.8 Audio Features .................................................... 43 8.9 RDS/RBDS .......................................................... 45 9. WLAN Global Functions ............................................ 46 9.1 WLAN CPU and Memory Subsystem .................. 46 9.2 One-Time Programmable Memory ...................... 46 9.3 GPIO Interface .................................................... 46 9.4 External Coexistence Interface ........................... 47 9.5 UART Interface .................................................... 48 Document Number: 002-15053 Rev. *D 9.6 JTAG Interface .................................................... 48 9.7 SPROM Interface ................................................ 48 10. WLAN Host Interfaces .............................................. 49 10.1 SDIO v3.0 .......................................................... 49 10.2 PCI Express Interface ....................................... 51 11. Wireless LAN MAC and PHY ................................... 53 11.1 IEEE 802.11ac Draft MAC ................................. 53 11.2 IEEE 802.11ac Draft PHY ................................. 55 12. WLAN Radio Subsystem ......................................... 57 12.1 Receiver Path .................................................... 59 12.2 Transmit Path .................................................... 59 12.3 Calibration ......................................................... 59 13. Pin Information ......................................................... 60 13.1 Ball Maps ........................................................... 60 13.2 Pin Lists ............................................................. 61 13.3 Signal Descriptions ............................................ 77 13.4 WLAN/BT GPIO Signals and Strapping Options 90 13.5 GPIO Alternative Signal Functions .................... 91 13.6 I/O States .......................................................... 93 14. DC Characteristics ................................................... 96 14.1 Absolute Maximum Ratings ............................... 96 14.2 Environmental Ratings ...................................... 96 14.3 Electrostatic Discharge Specifications .............. 96 14.4 Recommended Operating Conditions and DC Characteristics ............................................ 97 15. Bluetooth RF Specifications .................................... 99 16. FM Receiver Specifications ................................... 105 17. WLAN RF Specifications ........................................ 109 17.1 Introduction ...................................................... 109 17.2 2.4 GHz Band General RF Specifications ....... 109 17.3 WLAN 2.4 GHz Receiver Performance Specifications ................................................. 110 17.4 WLAN 2.4 GHz Transmitter Performance Specifications .................................................. 115 17.5 WLAN 5 GHz Receiver Performance Specifications .................................................. 117 17.6 WLAN 5 GHz Transmitter Performance Specifications .................................................. 123 18. Internal Regulator Electrical Specifications ........ 124 18.1 Core Buck Switching Regulator ....................... 124 18.2 3.3V LDO (LDO3P3) ....................................... 125 18.3 3.3V LDO (LDO3P3_B) ................................... 126 18.4 2.5V LDO (BTLDO2P5) ................................... 127 18.5 CLDO .............................................................. 128 18.6 LNLDO ............................................................ 129 19. System Power Consumption ................................. 130 19.1 WLAN Current Consumption ........................... 130 19.2 Bluetooth and FM Current Consumption ......... 132 20. Interface Timing and AC Characteristics ............. 133 20.1 SDIO Timing .................................................... 133 20.2 PCI Express Interface Parameters .................. 141 20.3 JTAG Timing ................................................... 142 21. Power-Up Sequence and Timing ........................... 143 21.1 Sequencing of Reset and Regulator Control Signals ............................................................ 143 Page 4 of 155 ADVANCE 22. Package Information .............................................. 148 22.1 Package Thermal Characteristics ................... 148 22.2 Junction Temperature Estimation and PSIJT Versus ThetaJC ........................................................................... 148 22.3 Environmental Characteristics ......................... 148 23. Mechanical Information ......................................... 149 24. Ordering Information .............................................. 153 Document Number: 002-15053 Rev. *D CYW4356 25. Additional Information ........................................... 153 25.1 Acronyms and Abbreviations ........................... 153 25.2 References ...................................................... 153 26. IoT Resources ......................................................... 153 Document History ......................................................... 154 Sales, Solutions, and Legal Information .................... 155 Page 5 of 155 ADVANCE CYW4356 1. Overview 1.1 Overview The Cypress CYW4356 single-chip device provides the highest level of integration for a mobile or handheld wireless system, with integrated IEEE 802.11 a/b/g/n/ac MAC/baseband/radio, Bluetooth 4.1 + EDR (enhanced data rate), FM receiver, and Alliance for Wireless Power (A4WP) support. The wireless charging feature works in collaboration with the Wireless Power Transfer (WPT) BCM59350 front-end IC. It provides a small form-factor solution with minimal external components to drive down cost for mass volumes and allows for handheld device flexibility in size, form, and function. Comprehensive power management circuitry and software ensure the system can meet the needs of highly mobile devices that require minimal power consumption and reliable operation. Figure 2 shows the interconnect of all the major physical blocks in the CYW4356 and their associated external interfaces, which are described in greater detail in the following sections. Table 2. Device Options and Features Feature WLBGA WLCSP Package ball count 192 pins 395 bumps PCIe Yes Yes USB2.0 (Bluetooth) Yes Yes I2S Multiplexed onto six parallel Flash pins No GPIO 11 16 SDIO 3.0 Yes Yes WPT (BSC, GPIO) Yes Yes SPROM Yes Yes Document Number: 002-15053 Rev. *D Page 6 of 155 ADVANCE CYW4356 Figure 2. CYW4356 Block Diagram CYW4356 JTAG WLAN BT/FM FM RF FM Digital Cortex M3 PMU Controller SDIO ETM JTAG SDP FM RX *SDIO or *PCIe 2.0 PCIe Debug PTU UART/USB ROM APB Patch WD Timer Inter Ctrl SW Timer DMA OTP Bus Arb GPIO GPIO Ctrl RAM Debug UART CLB I2S/PCM1 802.11abgn SMPS Control GNSS LNA ANT Control BTFM Control Clock Sleep Clock Timer Management Wake/Sleep Control LPO PMU PMU Controller XO Buffer BT‐WLAN ECI POR UART JTAG JTAG I2S/PCM2 GPIO GPIO UART 2X2 LCNXNPHY IO Port Control BT Digital IO ROM BT RF BT PHY OTP ARM AHB SLIMBus MEIF XTAL POR AXI BACKPLANE Power XTAL OSC RAM AHB2 APB Bridge JTAG AHB Bus Matrix WPT Power Supply LDO LPO AHB BSC, GPIO SW REG Radio CORE0 CORE1 2.4 GHz 5 GHz 2.4 GHz 5 GHz FMRX 5 GHz IPA BPF LNA 2.4 GHz IPA Diplexer BPF LNA 5 GHz IPA BPF LNA 2.4 GHz IPA Diplexer BPF Shared LNA BT RX BT TX XTAL Document Number: 002-15053 Rev. *D VBAT VREG POR EXT LNA RF Switch Control Page 7 of 155 ADVANCE CYW4356 1.2 Features The CYW4356 supports the following features: ■ IEEE 802.11a/b/g/n/ac dual-band 2x2 MIMO radio with virtual-simultaneous dual-band operation ■ Bluetooth v4.1 + EDR with integrated Class 1 PA ■ Concurrent Bluetooth, FM (RX) RDS/RBDS, and WLAN operation ■ On-chip WLAN driver execution capable of supporting IEEE 802.11 functionality ■ Single- and dual-antenna support ❐ Single antenna with shared LNA ❐ Simultaneous BT/WLAN receive with single antenna ■ WLAN host interface options: ❐ SDIO v3.0 (1 bit/4 bit)—up to 208 MHz clock rate in SDR104 mode ❐ PCIe v3.0 for x1 lane and power management, running at Gen 1 speeds ■ BT host digital interface (can be used concurrently with above interfaces): ❐ UART (up to 4 Mbps) ■ BT supports full-speed USB 2.0-compliant interface ■ ECI—enhanced coexistence support, ability to coordinate BT SCO transmissions around WLAN receives ■ I2S/PCM for FM/BT audio, HCI for FM block control ■ HCI high-speed UART (H4, H4+, H5) transport support ■ Wideband speech support (16 bits linear data, MSB first, left justified at 4K samples/s for transparent air coding, both through I2S and PCM interface) ■ Bluetooth SmartAudio® technology improves voice and music quality to headsets ■ Bluetooth low power inquiry and page scan ■ Bluetooth Low Energy (BLE) support ■ Bluetooth Packet Loss Concealment (PLC) ■ Bluetooth Wideband Speech (WBS) ■ FM advanced internal antenna support ■ FM auto search/tuning functions ■ FM multiple audio routing options: I2S, PCM, eSCO, and A2DP ■ FM mono-stereo blend and switch, and soft mute support ■ FM audio pause detect support ■ Audio rate-matching algorithms ■ Multiple simultaneous A2DP audio stream ■ FM over Bluetooth operation and on-chip stereo headset emulation (SBC) ■ A4WP support Document Number: 002-15053 Rev. *D Page 8 of 155 ADVANCE CYW4356 1.3 Standards Compliance The CYW4356 supports the following standards: ■ Bluetooth 2.1 + EDR ■ Bluetooth 3.0 + HS ■ Bluetooth 4.1 (Bluetooth Low Energy) ■ 65 MHz to 108 MHz FM bands (US, Europe, and Japan) ■ IEEE802.11ac mandatory and optional requirements for 20 MHz, 40 MHz, and 80 MHz channels ■ IEEE 802.11n—Handheld Device Class (Section 11) ■ IEEE 802.11a ■ IEEE 802.11b ■ IEEE 802.11g ■ IEEE 802.11d ■ IEEE 802.11h ■ IEEE 802.11i ■ Security: ❐ WEP ❐ WPA Personal ❐ WPA2 Personal ❐ WMM ❐ WMM-PS (U-APSD) ❐ WMM-SA ❐ AES (Hardware Accelerator) ❐ TKIP (HW Accelerator) ❐ CKIP (SW Support) ■ Proprietary Protocols: ❐ CCXv2 ❐ CCXv3 ❐ CCXv4 ❐ CCXv5 ■ IEEE 802.15.2 Coexistence Compliance—on silicon solution compliant with IEEE 3 wire requirements The CYW4356 will support the following future drafts/standards: ■ IEEE 802.11r—Fast Roaming (between APs) ■ IEEE 802.11w—Secure Management Frames ■ A4WP Wireless Power Transfer System Baseline System Specification V1.0 ■ IEEE 802.11 Extensions: ❐ IEEE 802.11e QoS Enhancements (In accordance with the WMM specification, QoS is already supported.) ❐ IEEE 802.11h 5 GHz Extensions ❐ IEEE 802.11i MAC Enhancements ❐ IEEE 802.11k Radio Resource Measurement Document Number: 002-15053 Rev. *D Page 9 of 155 ADVANCE CYW4356 2. Power Supplies and Power Management 2.1 Power Supply Topology One Buck regulator, multiple LDO regulators, and a power management unit (PMU) are integrated into the CYW4356. All regulators are programmable via the PMU. These blocks simplify power supply design for Bluetooth, WLAN, and FM functions in embedded designs. A single VBAT (3.0V to 5.25V DC max.) and VIO supply (1.8V to 3.3V) can be used, with all additional voltages being provided by the regulators in the CYW4356. Two control signals, BT_REG_ON and WL_REG_ON, are used to power-up the regulators and take the respective section out of reset. The CBUCK CLDO and LNLDO power up when any of the reset signals are deasserted. All regulators are powered down only when both BT_REG_ON and WL_REG_ON are deasserted. The CLDO and LNLDO may be turned off/on based on the dynamic demands of the digital baseband. The CYW4356 allows for an extremely low power-consumption mode by completely shutting down the CBUCK, CLDO, and LNLDO regulators. When in this state, LPLDO1 (which is a low-power linear regulator supplied by the system VIO supply) provides the CYW4356 with all the voltages it requires, further reducing leakage currents. 2.2 CYW4356 PMU Features ■ VBAT to 1.35Vout (600 mA maximum) Core-Buck (CBUCK) switching regulator ■ VBAT to 3.3Vout (600 mA maximum) LDO3P3 ■ VBAT to 3.3Vout (150 mA maximum) LDO3P3_B ■ VBAT to 2.5V out (70 mA maximum) BTLDO2P5 ■ 1.35V to 1.2Vout (150 mA maximum) LNLDO ■ 1.35V to 1.2Vout (300 mA maximum) CLDO with bypass mode for deep-sleep ■ Additional internal LDOs (not externally accessible) Figure 3 illustrates the typical power topology for the CYW4356. The shaded areas are internal to the CYW4356. Document Number: 002-15053 Rev. *D Page 10 of 155 ADVANCE CYW4356 Figure 3. Typical Power Topology for the CYW4356 Internal LNLDO Internal LNLDO Internal VCOLDO Internal LNLDO XTAL LDO 30 mA 1.2V WL RF – AFE 1.2V WL RF – TX (2.4 GHz, 5 GHz) 1.2V WL RF – LOGEN (2.4 GHz, 5 GHz) 1.2V WL RF – RX/LNA (2.4 GHz, 5 GHz) 1.2V WL RF – XTAL WL RF – RFPLL PFD/MMD LNLDO Max. 150 mA 1.2V BT RF/FM DFE/DFLL WL_REG_ON PCIE PLL/RXTX BT_REG_ON Core Buck Regulator CBUCK Mx. 600 mA VBAT WLAN BBPLL/DFLL 1.35V WLAN/BT/CLB/Top, Always‐on WL OTP VDDIO LPLDO1 3 mA 1.1V CLDO Max. 300 mA (Bypass in deep sleep) WL PHY 1.2V–1.1V WL DIGITAL BT DIGITAL WL/BT SRAMs BTLDO2P5 Max. 70 mA 2.5V BT CLASS 1 PA WL RF‐PA (2.4 GHz, 5 GHz) LDO3P3 Max. 600 mA WL PAD (2.4 GHz, 5 GHz) 3.3V VDDIO_RF 3.3V Internal LNLDO Internal LNLDO Document Number: 002-15053 Rev. *D 2.5V LDO3P3_B Max. 150 mA 2.5V WL OTP 3.3V WL RF – VCO WL RF – CP Page 11 of 155 ADVANCE CYW4356 2.3 WLAN Power Management The CYW4356 has been designed with the stringent power consumption requirements of mobile devices in mind. All areas of the chip design are optimized to minimize power consumption. Silicon processes and cell libraries were chosen to reduce leakage current and supply voltages. Additionally, the CYW4356 integrated RAM is a high Vt memory with dynamic clock control. The dominant supply current consumed by the RAM is leakage current only. Additionally, the CYW4356 includes an advanced WLAN power management unit (PMU) sequencer. The PMU sequencer provides significant power savings by putting the CYW4356 into various power management states appropriate to the current environment and activities that are being performed. The power management unit enables and disables internal regulators, switches, and other blocks based on a computation of the required resources and a table that describes the relationship between resources and the time needed to enable and disable them. Power up sequences are fully programmable. Configurable, free-running counters (running at 32.768 kHz LPO clock) in the PMU sequencer are used to turn on/ turn off individual regulators and power switches. Clock speeds are dynamically changed (or gated altogether) for the current mode. Slower clock speeds are used wherever possible. The CYW4356 WLAN power states are described as follows: ■ Active mode— All WLAN blocks in the CYW4356 are powered up and fully functional with active carrier sensing and frame transmission and receiving. All required regulators are enabled and put in the most efficient mode based on the load current. Clock speeds are dynamically adjusted by the PMU sequencer. ■ Deep-sleep mode—Most of the chip including both analog and digital domains and most of the regulators are powered off. All main clocks (PLL, crystal oscillator, or TCXO) are shut down to reduce active power to the minimum. The 32.768 kHz LPO clock is available only for the PMU sequencer. This condition is necessary to allow the PMU sequencer to wake up the chip and transition to Active mode. Logic states in the digital core are saved and preserved into a retention memory in the always-ON domain before the digital core is powered off. Upon a wake-up event triggered by the PMU timers, an external interrupt or a host resumes through the SDIO bus and logic states in the digital core are restored to their pre-deep-sleep settings to avoid lengthy HW reinitialization. In Deep-sleep mode, the primary source of power consumption is leakage current. ■ Power-down mode—The CYW4356 is effectively powered off by shutting down all internal regulators. The chip is brought out of this mode by external logic reenabling the internal regulators. 2.4 PMU Sequencing The PMU sequencer is responsible for minimizing system power consumption. It enables and disables various system resources based on a computation of the required resources and a table that describes the relationship between resources and the time needed to enable and disable them. Resource requests may come from several sources: clock requests from cores, the minimum resources defined in the ResourceMin register, and the resources requested by any active resource request timers. The PMU sequencer maps clock requests into a set of resources required to produce the requested clocks. Each resource is in one of four states: enabled, disabled, transition_on, and transition_off and has a timer that contains 0 when the resource is enabled or disabled and a non-zero value in the transition states. The timer is loaded with the time_on or time_off value of the resource when the PMU determines that the resource must be enabled or disabled. That timer decrements on each 32.768 kHz PMU clock. When it reaches 0, the state changes from transition_off to disabled or transition_on to enabled. If the time_on value is 0, the resource can go immediately from disabled to enabled. Similarly, a time_off value of 0 indicates that the resource can go immediately from enabled to disabled. The terms enable sequence and disable sequence refer to either the immediate transition or the timer load-decrement sequence. During each clock cycle, the PMU sequencer performs the following actions: ■ Computes the required resource set based on requests and the resource dependency table. ■ Decrements all timers whose values are non zero. If a timer reaches 0, the PMU clears the ResourcePending bit for the resource and inverts the ResourceState bit. ■ Compares the request with the current resource status and determines which resources must be enabled or disabled. ■ Initiates a disable sequence for each resource that is enabled, no longer being requested, and has no powered up dependents. ■ Initiates an enable sequence for each resource that is disabled, is being requested, and has all of its dependencies enabled. Document Number: 002-15053 Rev. *D Page 12 of 155 ADVANCE CYW4356 2.5 Power-Off Shutdown The CYW4356 provides a low-power shutdown feature that allows the device to be turned off while the host, and any other devices in the system, remain operational. When the CYW4356 is not needed in the system, VDDIO_RF and VDDC are shut down while VBAT and VDDIO remain powered. This allows the CYW4356 to be effectively off while keeping the I/O pins powered so that they do not draw extra current from any other devices connected to the I/O. During a low-power shut-down state, provided VDDIO remains applied to the CYW4356, all outputs are tristated, and most inputs signals are disabled. Input voltages must remain within the limits defined for normal operation. This is done to prevent current paths or create loading on any digital signals in the system, and enables the CYW4356 to be fully integrated in an embedded device and take full advantage of the lowest power-savings modes. When the CYW4356 is powered on from this state, it is the same as a normal power-up and the device does not retain any information about its state from before it was powered down. 2.6 Power-Up/Power-Down/Reset Circuits The CYW4356 has two signals (see Table 3) that enable or disable the Bluetooth and WLAN circuits and the internal regulator blocks, allowing the host to control power consumption. For timing diagrams of these signals and the required power-up sequences, see Section 21. Power-Up Sequence and Timing. Table 3. Power-Up/Power-Down/Reset Control Signals Signal Description WL_REG_ON This signal is used by the PMU (with BT_REG_ON) to power up the WLAN section. It is also OR-gated with the BT_REG_ON input to control the internal CYW4356 regulators. When this pin is high, the regulators are enabled and the WLAN section is out of reset. When this pin is low, the WLAN section is in reset. If BT_REG_ON and WL_REG_ON are both low, the regulators are disabled. This pin has an internal 200 k pull-down resistor that is enabled by default. It can be disabled through programming. BT_REG_ON This signal is used by the PMU (with WL_REG_ON) to decide whether or not to power down the internal CYW4356 regulators. If BT_REG_ON and WL_REG_ON are low, the regulators will be disabled. This pin has an internal 200 k pull-down resistor that is enabled by default. It can be disabled through programming. 2.7 Wireless Charging The CYW4356 combo IC is designed for paired operation with the BCM59350 wireless power transfer front-end chip. Working together, the two chips form a power receiver unit (PRU) that is compliant with the Alliance for Wireless Power specification (A4WP). High-level functional block diagram for wireless charging is provided in Figure 4. The power transmit unit (PTU) resides in the charging pad while the power receive unit is integrated into the mobile device. The charging process begins as the mobile device is placed onto the charging pad. The power is transferred from PTU to PRU through the TX and RX coils by means of magnetic induction. The Bluetooth control link handles communications, i.e., handshaking, between them. PTU is a BLE client, which gets performance data from the BLE server (PRU) in order to adapt its power to the mobile's need. Figure 4. High-Level Functional Block Diagram for Wireless Charging Power Transmit Unit (PTU) Power Receiver Unit (PRU) USB VBUS Detect VBUCK WPT Transmit WPT Tx Coil Resonator Wireless Power Transfer WPT Rx Coil Resonator BCM59350 WPT Front End WPT Control BLE BT Antenna Bluetooth Control Link Document Number: 002-15053 Rev. *D BT Antenna Power Switch Battery PMU GPIO WPT 1.8/3.3 System power CYW4356 Bluetooth Low‐Energy (BLE) Charger System control i/f Application Processor Page 13 of 155 ADVANCE CYW4356 Further details on the PRU are depicted in Figure 5. It shows both ICs along with a power switch, charger, power management IC, and the application processor (system). Figure 5. Power Receiver Unit Switch kept always ON unless disabled by 59350 USB connector VBUS DP DM GND VRECT cntl filter VBUS sense 59350 VRECT VRECT VIN_BUCK VBUS detect AUXLDO Register controlled input select WPC /PMA coil Vrect_low Vrect_high 20V LDO VBUCK AUXLDO VRECT comparator 1.8V VSRC PWR MGR POR OTP A4WP coil RECT control VLDO VLDO VRECT VBUCK IBUCK FieldCLK Charger / OTG Buck cntl 1.2A CLK GEN CHGsrc FB PMIC System interface VBUCK_FB VBUCK ADC Tjunc Tntc VRECT WPC / PMA controller Control Logic both LDOs ON (FIELD_S) VBUCK 1V8 LDO 3V3 LDO 100 mA 100 mA Register controlled LDO input select SYSVDDIO (1.8V) VBAT (2.9V‐4.5V) Pre‐OVP Z‐Tune BSC, INTb, GPIO NTC ADC bias in GPIO GPIO 1V8 1p8 SPDT VBAT SPDT VDDO Digtest VDD5otp VSRC INTb SCL SDA Test pins BSC INTb VDDIO VBAT WPT interface PMU BLE antenna Logical OR BLE subsys POR WLAN‐BLE combo Document Number: 002-15053 Rev. *D POR Internal pwr System interfaces (SDIO, PCIe, LPO, GPIO) BT_REG_ON WL_REG_ON Page 14 of 155 ADVANCE CYW4356 Figure 6 shows pin-to-pin connections between the CYW4356 and BCM59350, which consist of the following: ■ Two Broadcom Serial Control (BSC)1 data and clock lines. ■ Two DC power supply lines. ■ One interrupt (INTb) to the WLAN chip. ■ One GPIO line, which is passed through an OR gate along with another signal from the application processor AP. This is for BT_REG_ON function, as illustrated in Figure 6. Figure 6. BCM59350 and CYW4356 Interface BCM59350 CYW4356 3V3LDO VBAT 1V8LDO VDDIO SCL SDA INTb GPIO AP BT_GPIO_5 BT_GPIO_4 BT_GPIO_3 BT_REG_ON BT_GPIO_2 1. The Broadcom Serial Control bus is a proprietary bus compliant with the Philips I2C bus/interface. Document Number: 002-15053 Rev. *D Page 15 of 155 ADVANCE CYW4356 3. Frequency References An external crystal is used for generating all radio frequencies and normal operation clocking. As an alternative, an external frequency reference may be used. In addition, a low-power oscillator (LPO) is provided for lower power mode timing. 3.1 Crystal Interface and Clock Generation The CYW4356 can use an external crystal to provide a frequency reference. The recommended configuration for the crystal oscillator including all external components is shown in Figure 7. Consult the reference schematics for the latest configuration. Figure 7. Recommended Oscillator Configuration C* W R F _X TA L _IN 3 7 .4 M H z C* X o h m s* W R F _X TA L _O U T * V alu e s d e te rm in e d b y crystal d rive le ve l. S e e re fe re n ce sch e m atics fo r d e tails . A fractional-N synthesizer in the CYW4356 generates the radio frequencies, clocks, and data/packet timing, enabling it to operate using a wide selection of frequency references. For SDIO and PCIe WLAN host applications, the recommended default frequency reference is a 37.4 MHz crystal. For PCIe applications, see Table 4 for details on alternatives for the external frequency reference. The signal characteristics for the crystal oscillator interface are also listed in Table 4. Note: Although the fractional-N synthesizer can support alternative reference frequencies, frequencies other than the default require support to be added in the driver, plus additional extensive system testing. Contact Cypress for further details. 3.2 External Frequency Reference For operation in SDIO mode only, an alternative to a crystal (an external precision frequency reference) can be used. The recommended default frequency is 52 MHz ±10 ppm, and it must meet the phase noise requirements listed in Table 4. If used, the external clock should be connected to the WRF_XTAL_IN pin through an external 1000 pF coupling capacitor, as shown in Figure 8. The internal clock buffer connected to this pin will be turned OFF when the CYW4356 goes into sleep mode. When the clock buffer turns ON and OFF there will be a small impedance variation. Power must be supplied to the WRF_XTAL_VDD1P5 pin. Figure 8. Recommended Circuit to Use with an External Reference Clock 1000 pF Reference Clock WRF_XTAL_IN NC Document Number: 002-15053 Rev. *D WRF_XTAL_OUT Page 16 of 155 ADVANCE CYW4356 Table 4. Crystal Oscillator and External Clock—Requirements and Performance Parameter Min. Frequency External Frequency Referenceb, c Crystala Conditions/Notes Typ. Max. Min. Typ. Max. Units 2.4G and 5G bands: IEEE 802.11ac 35 operation, SDIO3.0, and PCIe WLAN interfaces 37.4 – – 52 – MHz 2.4G and 5G bands, IEEE 802.11ac – operation, PCIe interface alternative frequency 40 – – – – MHz 5G band: IEEE 802.11n operation only 19 – 52 35 – 52 MHz 2.4G band: IEEE 802.11n operation, and both bands legacy 802.11a/b/g operation only Ranges between 19 MHz and 52 MHzd, e Frequency tolerance over the lifetime of the equipment, including temperaturef Without trimming –20 – 20 –20 – 20 ppm Crystal load capacitance – – 12 – – – – pF ESR – – – 60 – – – Ω Drive level External crystal must be able to tolerate this drive level. 200 – – – – – μW Input impedance (WRF_XTAL_IN) Resistive – – – 30 100 – kΩ Capacitive – – 7.5 – – 7.5 pF WRF_XTAL_IN Input low level DC-coupled digital signal – – – 0 – 0.2 V WRF_XTAL_IN Input high level DC-coupled digital signal – – – 1.0 – 1.26 V WRF_XTAL_IN input voltage (see Figure 8) AC-coupled analog signal – – – 400 – 1200 mVp-p Duty cycle 37.4 MHz clock – – – 40 50 60 % Noiseg Phase (IEEE 802.11b/g) 37.4 MHz clock at 10 kHz offset – – – – – –129 dBc/Hz 37.4 MHz clock at 100 kHz offset – – – – – –136 dBc/Hz Phase Noiseg (IEEE 802.11a) 37.4 MHz clock at 10 kHz offset – – – – – –137 dBc/Hz 37.4 MHz clock at 100 kHz offset – – – – – –144 dBc/Hz Phase Noiseg (IEEE 802.11n, 2.4 GHz) 37.4 MHz clock at 10 kHz offset – – – – – –134 dBc/Hz 37.4 MHz clock at 100 kHz offset – – – – – –141 dBc/Hz Phase Noiseg,h (IEEE 802.11n, 5 GHz) 37.4 MHz clock at 10 kHz offset – – – – – –142 dBc/Hz 37.4 MHz clock at 100 kHz offset – – – – – –149 dBc/Hz Phase Noiseg (IEEE 802.11ac, 5 GHz) 37.4 MHz clock at 10 kHz offset – – – – – –150 dBc/Hz 37.4 MHz clock at 100 kHz offset – – – – – –157 dBc/Hz a. (Crystal) Use WRF_XTAL_IN and WRF_XTAL_OUT. b. See External Frequency Reference for alternate connection methods. c. For a clock reference other than 37.4 MHz, 20 × log10(f/ 37.4) dB should be added to the limits, where f = the reference clock frequency in MHz. d. BT_TM6 should be tied low for a 52 MHz clock reference. For other frequencies, BT_TM6 should be tied high. Note that 52 MHz is not an auto–detected frequency using the LPO clock. e. The frequency step size is approximately 80 Hz resolution. f. It is the responsibility of the equipment designer to select oscillator components that comply with these specifications. g. Assumes that external clock has a flat phase noise response above 100 kHz. h. If the reference clock frequency is <35 MHz the phase noise requirements must be tightened by an additional 2 dB. Document Number: 002-15053 Rev. *D Page 17 of 155 ADVANCE CYW4356 3.3 External 32.768 kHz Low-Power Oscillator The CYW4356 uses a secondary low-frequency clock for Low-Power mode timing. Either the internal low- precision LPO or an external 32.768 kHz precision oscillator is required. The internal LPO frequency range is approximately 33 kHz (± 30%) over process, voltage, and temperature, which is adequate for some applications. However, one trade-off caused by this wide LPO tolerance is a small current consumption increase during power save mode that is incurred by the need to wake up earlier to avoid missing beacons. Whenever possible, the preferred approach is to use a precision external 32.768 kHz clock which meets the requirements listed in Table 5. Table 5. External 32.768 kHz Sleep Clock Specifications Parameter LPO Clock Unit Nominal input frequency 32.768 kHz Frequency accuracy ±200 ppm Duty cycle 30 – 70 % Input signal amplitude 200–3300a, b mV, p-p Signal type Square-wave or sine-wave – Input impedancec > 100k Ω <5 pF < 10,000 ppm Clock jitter (during initial start-up) a. The LPO_IN input has an internal DC blocking capacitor, no external DC blocking is required. b. The input DC offset must be ≥ 0V to avoid conduction by the ESD protection diode. c. When power is applied or switched off. Document Number: 002-15053 Rev. *D Page 18 of 155 ADVANCE CYW4356 4. Bluetooth + FM Subsystem Overview The Cypress CYW4356 is a Bluetooth 4.1 + EDR-compliant, baseband processor/2.4 GHz transceiver with an integrated FM/RDS/ RBDS receiver. It features the highest level of integration and eliminates all critical external components, thus minimizing the footprint, power consumption, and system cost of a Bluetooth plus FM radio solution. The CYW4356 is the optimal solution for any Bluetooth voice and/or data application that also requires an FM radio receiver. The Bluetooth subsystem presents a standard Host Controller Interface (HCI) via a high-speed UART and PCM for audio. The FM subsystem supports the HCI control interface, analog output, as well as I2S and PCM interfaces. The CYW4356 incorporates all Bluetooth 4.1 features including secure simple pairing, sniff subrating, and encryption pause and resume. The CYW4356 Bluetooth radio transceiver provides enhanced radio performance to meet the most stringent mobile phone temperature applications and the tightest integration into mobile handsets and portable devices. It is fully compatible with any of the standard TCXO frequencies and provides full radio compatibility to operate simultaneously with GPS, WLAN, and cellular radios. The Bluetooth transmitter also features a Class 1 power amplifier with Class 2 capability. 4.1 Features Major Bluetooth features of the CYW4356 include: ■ Supports key features of upcoming Bluetooth standards ■ Fully supports Bluetooth Core Specification version 4.1 + (Enhanced Data Rate) EDR features: ❐ Adaptive Frequency Hopping (AFH) ❐ Quality of Service (QoS) ❐ Extended Synchronous Connections (eSCO)—Voice Connections ❐ Fast Connect (interlaced page and inquiry scans) ❐ Secure Simple Pairing (SSP) ❐ Sniff Subrating (SSR) ❐ Encryption Pause Resume (EPR) ❐ Extended Inquiry Response (EIR) ❐ Link Supervision Timeout (LST) ■ UART baud rates up to 4 Mbps ■ Supports all Bluetooth 4.1 packet types ■ Supports maximum Bluetooth data rates over HCI UART ■ BT supports full-speed USB 2.0-compliant interface ■ Multipoint operation with up to seven active slaves ❐ Maximum of seven simultaneous active ACL links ❐ Maximum of three simultaneous active SCO and eSCO connections with scatternet support ■ Trigger Broadcom fast connect (TBFC) ■ Narrowband and wideband packet loss concealment ■ Scatternet operation with up to four active piconets with background scan and support for scatter mode ■ High-speed HCI UART transport support with low-power out-of-band BT_DEV_WAKE and BT_HOST_WAKE signaling (see “Host Controller Power Management”) ■ Channel quality driven data rate and packet type selection ■ Standard Bluetooth test modes ■ Extended radio and production test mode features ■ Full support for power savings modes ❐ Bluetooth clock request ❐ Bluetooth standard sniff ❐ Deep-sleep modes and software regulator shutdown ■ TCXO input and auto-detection of all standard handset clock frequencies. Also supports a low-power crystal, which can be used during power-save mode for better timing accuracy. Document Number: 002-15053 Rev. *D Page 19 of 155 ADVANCE CYW4356 Major FM Radio features include: ■ 65 MHz to 108 MHz FM bands supported (US, Europe, and Japan) ■ FM subsystem control using the Bluetooth HCI interface ■ FM subsystem operates from reference clock inputs. ■ Improved audio interface capabilities with full-featured bidirectional PCM and I2S ■ I2S can be master or slave. FM receiver-specific features include: ■ Excellent FM radio performance with 1 µV sensitivity for 26 dB (S+N)/N ■ Signal-dependent stereo/mono blending ■ Signal dependent soft mute ■ Auto search and tuning modes ■ Audio silence detection ■ RSSI, IF frequency, status indicators ■ RDS and RBDS demodulator and decoder with filter and buffering functions ■ Automatic frequency jump 4.2 Bluetooth Radio The CYW4356 has an integrated radio transceiver that has been optimized for use in 2.4 GHz Bluetooth wireless systems. It has been designed to provide low-power, low-cost, robust communications for applications operating in the globally available 2.4 GHz unlicensed ISM band. It is fully compliant with the Bluetooth Radio Specification and EDR specification and meets or exceeds the requirements to provide the highest communication link quality of service. 4.2.1 Transmit The CYW4356 features a fully integrated zero-IF transmitter. The baseband transmit data is GFSK-modulated in the modem block and upconverted to the 2.4 GHz ISM band in the transmitter path. The transmitter path consists of signal filtering, I/Q upconversion, output power amplifier, and RF filtering. The transmitter path also incorporates /4-DQPSK for 2 Mbps and 8-DPSK for 3 Mbps to support EDR. The transmitter section is compatible to the Bluetooth Low Energy specification. The transmitter PA bias can also be adjusted to provide Bluetooth class 1 or class 2 operation. 4.2.2 Digital Modulator The digital modulator performs the data modulation and filtering required for the GFSK, /4-DQPSK, and 8-DPSK signal. The fully digital modulator minimizes any frequency drift or anomalies in the modulation characteristics of the transmitted signal and is much more stable than direct VCO modulation schemes. 4.2.3 Digital Demodulator and Bit Synchronizer The digital demodulator and bit synchronizer take the low-IF received signal and perform an optimal frequency tracking and bitsynchronization algorithm. 4.2.4 Power Amplifier The fully integrated PA supports Class 1 or Class 2 output using a highly linearized, temperature-compensated design. This provides greater flexibility in front-end matching and filtering. Due to the linear nature of the PA combined with some integrated filtering, external filtering is required to meet the Bluetooth and regulatory harmonic and spurious requirements. For integrated mobile handset applications in which Bluetooth is integrated next to the cellular radio, external filtering can be applied to achieve near thermal noise levels for spurious and radiated noise emissions. The transmitter features a sophisticated on-chip transmit signal strength indicator (TSSI) block to keep the absolute output power variation within a tight range across process, voltage, and temperature. Document Number: 002-15053 Rev. *D Page 20 of 155 ADVANCE CYW4356 4.2.5 Receiver The receiver path uses a low-IF scheme to downconvert the received signal for demodulation in the digital demodulator and bit synchronizer. The receiver path provides a high degree of linearity, an extended dynamic range, and high-order on-chip channel filtering to ensure reliable operation in the noisy 2.4 GHz ISM band. The front-end topology with built-in out-of-band attenuation enables the CYW4356 to be used in most applications with minimal off-chip filtering. For integrated handset operation, in which the Bluetooth function is integrated close to the cellular transmitter, external filtering is required to eliminate the desensitization of the receiver by the cellular transmit signal. 4.2.6 Digital Demodulator and Bit Synchronizer The digital demodulator and bit synchronizer take the low-IF received signal and perform an optimal frequency tracking and bit synchronization algorithm. 4.2.7 Receiver Signal Strength Indicator The radio portion of the CYW4356 provides a Receiver Signal Strength Indicator (RSSI) signal to the baseband, so that the controller can take part in a Bluetooth power-controlled link by providing a metric of its own receiver signal strength to determine whether the transmitter should increase or decrease its output power. 4.2.8 Local Oscillator Generation Local Oscillator (LO) generation provides fast frequency hopping (1600 hops/second) across the 79 maximum available channels. The LO generation subblock employs an architecture for high immunity to LO pulling during PA operation. The CYW4356 uses an internal RF and IF loop filter. 4.2.9 Calibration The CYW4356 radio transceiver features an automated calibration scheme that is fully self contained in the radio. No user interaction is required during normal operation or during manufacturing to provide the optimal performance. Calibration optimizes the performance of all the major blocks within the radio to within 2% of optimal conditions, including gain and phase characteristics of filters, matching between key components, and key gain blocks. This takes into account process variation and temperature variation. Calibration occurs transparently during normal operation during the settling time of the hops and calibrates for temperature variations as the device cools and heats during normal operation in its environment. Document Number: 002-15053 Rev. *D Page 21 of 155 ADVANCE CYW4356 5. Bluetooth Baseband Core The Bluetooth Baseband Core (BBC) implements all of the time critical functions required for high-performance Bluetooth operation. The BBC manages the buffering, segmentation, and routing of data for all connections. It also buffers data that passes through it, handles data flow control, schedules SCO/ACL TX/RX transactions, monitors Bluetooth slot usage, optimally segments and packages data into baseband packets, manages connection status indicators, and composes and decodes HCI packets. In addition to these functions, it independently handles HCI event types, and HCI command types. The following transmit and receive functions are also implemented in the BBC hardware to increase reliability and security of the TX/ RX data before sending over the air: ■ Symbol timing recovery, data deframing, forward error correction (FEC), header error control (HEC), cyclic redundancy check (CRC), data decryption, and data dewhitening in the receiver. ■ Data framing, FEC generation, HEC generation, CRC generation, key generation, data encryption, and data whitening in the transmitter. 5.1 Bluetooth 4.1 Features The BBC supports all Bluetooth 4.1 features, with the following benefits: ■ Dual-mode bluetooth Low Energy (BT and BLE operation) ■ Extended Inquiry Response (EIR): Shortens the time to retrieve the device name, specific profile, and operating mode. ■ Encryption Pause Resume (EPR): Enables the use of Bluetooth technology in a much more secure environment. ■ Sniff Subrating (SSR): Optimizes power consumption for low duty cycle asymmetric data flow, which subsequently extends battery life. ■ Secure Simple Pairing (SSP): Reduces the number of steps for connecting two devices, with minimal or no user interaction required. ■ Link Supervision Time Out (LSTO): Additional commands added to HCI and Link Management Protocol (LMP) for improved link time-out supervision. ■ QoS enhancements: Changes to data traffic control, which results in better link performance. Audio, human interface device (HID), bulk traffic, SCO, and enhanced SCO (eSCO) are improved with the erroneous data (ED) and packet boundary flag (PBF) enhancements. 5.2 Bluetooth Low Energy The CYW4356 supports the Bluetooth Low Energy operating mode. 5.3 Link Control Layer The link control layer is part of the Bluetooth link control functions that are implemented in dedicated logic in the link control unit (LCU). This layer consists of the command controller that takes commands from the software, and other controllers that are activated or configured by the command controller, to perform the link control tasks. Each task performs a different state in the Bluetooth Link Controller. ■ Major states: ❐ Standby ❐ Connection ■ Substates: ❐ Page ❐ Page Scan ❐ Inquiry ❐ Inquiry Scan ❐ Sniff Document Number: 002-15053 Rev. *D Page 22 of 155 ADVANCE CYW4356 5.4 Test Mode Support The CYW4356 fully supports Bluetooth Test mode as described in Part I:1 of the Specification of the Bluetooth System Version 3.0. This includes the transmitter tests, normal and delayed loopback tests, and reduced hopping sequence. In addition to the standard Bluetooth Test Mode, the CYW4356 also supports enhanced testing features to simplify RF debugging and qualification and type-approval testing. These features include: ■ Fixed frequency carrier wave (unmodulated) transmission ❐ Simplifies some type-approval measurements (Japan) ❐ Aids in transmitter performance analysis ■ Fixed frequency constant receiver mode ❐ Receiver output directed to I/O pin ❐ Allows for direct BER measurements using standard RF test equipment ❐ Facilitates spurious emissions testing for receive mode ■ Fixed frequency constant transmission ❐ Eight-bit fixed pattern or PRBS-9 ❐ Enables modulated signal measurements with standard RF test equipment 5.5 Bluetooth Power Management Unit The Bluetooth Power Management Unit (PMU) provides power management features that can be invoked by either software through power management registers or packet handling in the baseband core. The power management functions provided by the CYW4356 are: ■ RF Power Management ■ Host Controller Power Management ■ BBC Power Management ■ FM Power Management 5.5.1 RF Power Management The BBC generates power-down control signals for the transmit path, receive path, PLL, and power amplifier to the 2.4 GHz transceiver. The transceiver then processes the power-down functions accordingly. 5.5.2 Host Controller Power Management When running in UART mode, the CYW4356 may be configured so that dedicated signals are used for power management handshaking between the CYW4356 and the host. The basic power saving functions supported by those hand-shaking signals include the standard Bluetooth defined power savings modes and standby modes of operation. Table 6 describes the power-control hand-shake signals used with the UART interface. Table 6. Power Control Pin Description Signal Mapped to Pin Type Description BT_DEV_WAKE BT_GPIO_0 I Bluetooth device wake-up: Signal from the host to the CYW4356 indicating that the host requires attention. ■ Asserted: The Bluetooth device must wake-up or remain awake. ■ Deasserted: The Bluetooth device may sleep when sleep criteria are met. The polarity of this signal is software configurable and can be asserted high or low. BT_HOST_ WAKE BT_GPIO_1 O Host wake up. Signal from the CYW4356 to the host indicating that the CYW4356 requires attention. ■ Asserted: host device must wake-up or remain awake. ■ Deasserted: host device may sleep when sleep criteria are met. The polarity of this signal is software configurable and can be asserted high or low. CLK_REQ BT_CLK_REQ_OUT WL_CLK_REQ_OUT O The CYW4356 asserts CLK_REQ when Bluetooth or WLAN wants the host to turn on the reference clock. The CLK_REQ polarity is active-high. Add an external 100 kΩ pull-down resistor to ensure the signal is deasserted when the CYW4356 powers up or resets when VDDIO is present. Note: Pad function Control Register is set to 0 for these pins. See “DC Characteristics” for more details. Document Number: 002-15053 Rev. *D Page 23 of 155 ADVANCE CYW4356 The timing for the startup sequence is defined in Figure 9. Figure 9. Startup Signaling Sequence LPO VDDIO HostResetX Host I/Os unconfigured Host I/Os configured T1 BT_GPIO_0 (BT_DEV_WAKE ) BT_REG_ON BTH I/Os unconfigured T2 BT_GPIO_1 (BT_HOST_WAKE) BTH I/Os configured T3 Host side drives this line low BT_UART_CTS_N T4 BTH device drives this line low indicating transport is ready BT_UART_RTS_N CLK_REQ_OUT T5 Driven Pulled Notes: T1 is the time for Host to settle it’s IOs after a reset. T2 is the time for Host to drive BT_REG_ON high after the Host IOs are configured . T3 is the time for BTH (Bluetooth) device to settle its IOs after a reset and reference clock settling time has elapsed . T4 is the time for BTH device to drive BT_UART_RTS_N low after the Host drives BT_UART_CTS_N low. This assumes the BTH device has already completed initialization. T5 is the time for BTH device to drive CLK_REQ_OUT high after BT_REG_ON goes high. Note this pin is used for designs that use an external reference clock source from the Host. This pin is irrelevant for Crystal reference clock based designs where the BTH device generates it’s own reference clock from an external crystal connected to it’s oscillator circuit. Timing diagram assumes VBAT is present. Document Number: 002-15053 Rev. *D Page 24 of 155 ADVANCE CYW4356 5.5.3 BBC Power Management The following are low-power operations for the BBC: ■ Physical layer packet-handling turns the RF on and off dynamically within transmit/receive packets. ■ Bluetooth-specified low-power connection modes: sniff, hold, and park. While in these modes, the CYW4356 runs on the low-power oscillator and wakes up after a predefined time period. ■ A low-power shutdown feature allows the device to be turned off while the host and any other devices in the system remain operational. When the CYW4356 is not needed in the system, the RF and core supplies are shut down while the I/O remains powered. This allows the CYW4356 to effectively be off while keeping the I/O pins powered so they do not draw extra current from any other devices connected to the I/O. During the low-power shut-down state, provided VDDIO remains applied to the CYW4356, all outputs are tristated, and most input signals are disabled. Input voltages must remain within the limits defined for normal operation. This is done to prevent current paths or create loading on any digital signals in the system and enables the CYW4356 to be fully integrated in an embedded device to take full advantage of the lowest power-saving modes. Two CYW4356 input signals are designed to be high-impedance inputs that do not load the driving signal even if the chip does not have VDDIO power supplied to it: the frequency reference input (WRF_TCXO_IN) and the 32.768 kHz input (LPO). When the CYW4356 is powered on from this state, it is the same as a normal power-up, and the device does not contain any information about its state from the time before it was powered down. 5.5.4 FM Power Management The CYW4356 FM subsystem can operate independently of, or in tandem with, the Bluetooth RF and BBC subsystems. The FM subsystem power management scheme operates in conjunction with the Bluetooth RF and BBC subsystems. The FM block does not have a low power state, it is either on or off. 5.5.5 Wideband Speech The CYW4356 provides support for wideband speech (WBS) using on-chip SmartAudio technology. The CYW4356 can perform subband-codec (SBC), as well as mSBC, encoding and decoding of linear 16 bits at 16 kHz (256 Kbps rate) transferred over the PCM bus. 5.5.6 Packet Loss Concealment Packet Loss Concealment (PLC) improves apparent audio quality for systems with marginal link performance. Bluetooth messages are sent in packets. When a packet is lost, it creates a gap in the received audio bit-stream. Packet loss can be mitigated in several ways: ■ Fill in zeros. ■ Ramp down the output audio signal toward zero (this is the method used in current Bluetooth headsets). ■ Repeat the last frame (or packet) of the received bit-stream and decode it as usual (frame repeat). These techniques cause distortion and popping in the audio stream. The CYW4356 uses a proprietary waveform extension algorithm to provide dramatic improvement in the audio quality. Figure 10 and Figure 11 show audio waveforms with and without Packet Loss Concealment. Cypress PLC/BEC algorithms also support wideband speech. Figure 10. CVSD Decoder Output Waveform Without PLC Packet Loss Causes Ramp-down Document Number: 002-15053 Rev. *D Page 25 of 155 ADVANCE CYW4356 Figure 11. CVSD Decoder Output Waveform After Applying PLC 5.5.7 Audio Rate-Matching Algorithms The CYW4356 has an enhanced rate-matching algorithm that uses interpolation algorithms to reduce audio stream jitter that may be present when the rate of audio data coming from the host is not the same as the Bluetooth or FM audio data rates. 5.5.8 Codec Encoding The CYW4356 can support SBC and mSBC encoding and decoding for wideband speech. 5.5.9 Multiple Simultaneous A2DP Audio Stream The CYW4356 has the ability to take a single audio stream and output it to multiple Bluetooth devices simultaneously. This allows a user to share his or her music (or any audio stream) with a friend. 5.5.10 FM Over Bluetooth FM Over Bluetooth enables the CYW4356 to stream data from FM over Bluetooth without requiring the host to be awake. This can significantly extend battery life for usage cases where someone is listening to FM radio on a Bluetooth headset. 5.5.11 Burst Buffer Operation The CYW4356 has a data buffer that can buffer data being sent over the HCI and audio transports, then send the data at an increased rate. This mode of operation allows the host to sleep for the maximum amount of time, dramatically reducing system current consumption. 5.6 Adaptive Frequency Hopping The CYW4356 gathers link quality statistics on a channel by channel basis to facilitate channel assessment and channel map selection. The link quality is determined using both RF and baseband signal processing to provide a more accurate frequency-hop map. 5.7 Advanced Bluetooth/WLAN Coexistence The CYW4356 includes advanced coexistence technologies that are only possible with a Bluetooth/WLAN integrated die solution. These coexistence technologies are targeted at small form-factor platforms, such as cell phones and media players, including applications such as VoWLAN + SCO and Video-over-WLAN + High Fidelity BT Stereo. Support is provided for platforms that share a single antenna between Bluetooth and WLAN. Dual-antenna applications are also supported. The CYW4356 radio architecture allows for lossless simultaneous Bluetooth and WLAN reception for shared antenna applications. This is possible only via an integrated solution (shared LNA and joint AGC algorithm). It has superior performance versus implementations that need to arbitrate between Bluetooth and WLAN reception. The CYW4356 integrated solution enables MAC-layer signaling (firmware) and a greater degree of sharing via an enhanced coexistence interface. Information is exchanged between the Bluetooth and WLAN cores without host processor involvement. The CYW4356 also supports Transmit Power Control on the STA together with standard Bluetooth TPC to limit mutual interference and receiver desensitization. Preemption mechanisms are utilized to prevent AP transmissions from colliding with Bluetooth frames. Improved channel classification techniques have been implemented in Bluetooth for faster and more accurate detection and elimination of interferers (including non-WLAN 2.4 GHz interference). The Bluetooth AFH classification is also enhanced by the WLAN core’s channel information. 5.8 Fast Connection (Interlaced Page and Inquiry Scans) The CYW4356 supports page scan and inquiry scan modes that significantly reduce the average inquiry response and connection times. These scanning modes are compatible with the Bluetooth version 2.1 page and inquiry procedures. Document Number: 002-15053 Rev. *D Page 26 of 155 ADVANCE CYW4356 6. Microprocessor and Memory Unit for Bluetooth The Bluetooth microprocessor core is based on the ARM Cortex-M3 32-bit RISC processor with embedded ICE-RT debug and JTAG interface units. It runs software from the link control (LC) layer, up to the host controller interface (HCI). The ARM core is paired with a memory unit that contains 668 KB of ROM memory for program storage and boot ROM, 200 KB of RAM for data scratchpad and patch RAM code. The internal ROM allows for flexibility during power-on reset to enable the same device to be used in various configurations. At power-up, the lower-layer protocol stack is executed from the internal ROM memory. External patches may be applied to the ROM-based firmware to provide flexibility for bug fixes or features additions. These patches may be downloaded from the host to the CYW4356 through the UART transports. The mechanism for downloading via UART is identical to the proven interface of the CYW4330 device. 6.1 RAM, ROM, and Patch Memory The CYW4356 Bluetooth core has 200 KB of internal RAM which is mapped between general purpose scratch pad memory and patch memory and 668 KB of ROM used for the lower-layer protocol stack, test mode software, and boot ROM. The patch memory capability enables the addition of code changes for purposes of feature additions and bug fixes to the ROM memory. 6.2 Reset The CYW4356 has an integrated power-on reset circuit that resets all circuits to a known power-on state. The BT power-on reset (POR) circuit is out of reset after BT_REG_ON goes High. If BT_REG_ON is low, then the POR circuit is held in reset. Document Number: 002-15053 Rev. *D Page 27 of 155 ADVANCE CYW4356 7. Bluetooth Peripheral Transport Unit 7.1 SPI Interface The CYW4356 supports a slave SPI HCI transport with an input clock range of up to 16 MHz. Higher clock rates can be possible. The physical interface between the SPI master and the CYW4356 consists of the four SPI signals (SPI_CSB, SPI_CLK, SPI_SI, and SPI_SO) and one interrupt signal (SPI_INT). The SPI signals are muxed onto the UART signals, see Table 7. The CYW4356 can be configured to accept active-low or active-high polarity on the SPI_CSB chip select signal. It can also be configured to drive an activelow or active-high SPI_INT interrupt signal. Bit ordering on the SPI_SI and SPI_SO data lines can be configured as either little-endian or big-endian. Additionally, proprietary sleep mode and half-duplex handshaking is implemented between the SPI master and the CYW4356. The SPI_INT is required to negotiate the start of a transaction. The SPI interface does not require flow control in the middle of a payload. The FIFO is large enough to handle the largest packet size. Only the SPI master can stop the flow of bytes on the data lines, since it controls SPI_CSB and SPI_CLK. Flow control should be implemented in the higher layer protocols. Table 7. SPI to UART Signal Mapping SPI Signals UART Signals SPI_CLK UART_CTS_N SPI_CSB UART_RTS_N SPI_MISO UART_TXD SPI_MOSI UART_RXD SPI_INT BT_DEV_WAKE 7.2 SPI/UART Transport Detection The BT_HOST_WAKE (BT_GPIO1) pin is also used for BT transport detection. The transport detection occurs during the power-up sequence. It selects either UART or SPI transport operation based on the following pin state: ■ If the BT_HOST_WAKE (BT_GPIO1) pin is pulled low by an external pull-down during power-up, it selects the SPI transport interface. ■ If the BT_HOST_WAKE (BT_GPIO1) pin is not pulled low externally during power-up, then the default internal pull-up is detected as a high and it selects the UART transport interface. When the A4WP feature is not used and USB is selected as the Bluetooth interface to the host, an external pull-up (outside the chip) 10 KΩ resistor to BT_VDDIO is required. The pull-up is not necessary but is recommended when the Bluetooth/host interface is UART instead of USB. 7.3 PCM Interface The CYW4356 supports two independent PCM interfaces that share the pins with the I2S interfaces. The PCM Interface on the CYW4356 can connect to linear PCM codec devices in master or slave mode. In master mode, the CYW4356 generates the PCM_CLK and PCM_SYNC signals, and in slave mode, these signals are provided by another master on the PCM interface and are inputs to the CYW4356. The configuration of the PCM interface may be adjusted by the host through the use of vendor-specific HCI commands. 7.3.1 Slot Mapping The CYW4356 supports up to three simultaneous full-duplex SCO or eSCO channels through the PCM interface. These three channels are time-multiplexed onto the single PCM interface by using a time-slotting scheme where the 8 kHz or 16 kHz audio sample interval is divided into as many as 16 slots. The number of slots is dependent on the selected interface rate of 128 kHz, 512 kHz, or 1024 kHz. The corresponding number of slots for these interface rate is 1, 2, 4, 8, and 16, respectively. Transmit and receive PCM data from an SCO channel is always mapped to the same slot. The PCM data output driver tristates its output on unused slots to allow other devices to share the same PCM interface signals. The data output driver tristates its output after the falling edge of the PCM clock during the last bit of the slot. 7.3.2 Frame Synchronization The CYW4356 supports both short- and long-frame synchronization in both master and slave modes. In short-frame synchronization mode, the frame synchronization signal is an active-high pulse at the audio frame rate that is a single-bit period in width and is synchronized to the rising edge of the bit clock. The PCM slave looks for a high on the falling edge of the bit clock and expects the first bit of the first slot to start at the next rising edge of the clock. In long-frame synchronization mode, the frame synchronization signal is again an active-high pulse at the audio frame rate; however, the duration is three bit periods and the pulse starts coincident with the first bit of the first slot. Document Number: 002-15053 Rev. *D Page 28 of 155 ADVANCE CYW4356 7.3.3 Data Formatting The CYW4356 may be configured to generate and accept several different data formats. For conventional narrowband speech mode, the CYW4356 uses 13 of the 16 bits in each PCM frame. The location and order of these 13 bits can be configured to support various data formats on the PCM interface. The remaining three bits are ignored on the input and may be filled with 0s, 1s, a sign bit, or a programmed value on the output. The default format is 13-bit 2’s complement data, left justified, and clocked MSB first. 7.3.4 Wideband Speech Support When the host encodes Wideband Speech (WBS) packets in transparent mode, the encoded packets are transferred over the PCM bus for an eSCO voice connection. In this mode, the PCM bus is typically configured in master mode for a 4 kHz sync rate with 16bit samples, resulting in a 64 Kbps bit rate. The CYW4356 also supports slave transparent mode using a proprietary rate-matching scheme. In SBC-code mode, linear 16-bit data at 16 kHz (256 Kbps rate) is transferred over the PCM bus. 7.3.5 Multiplexed Bluetooth and FM Over PCM In this mode of operation, the CYW4356 multiplexes both FM and Bluetooth audio PCM channels over the same interface, reducing the number of required I/Os. This mode of operation is initiated through an HCI command from the host. The format of the data stream consists of three channels: a Bluetooth channel followed by two FM channels (audio left and right). In this mode of operation, the bus data rate only supports 48 kHz operation per channel with 16 bits sent for each channel. This is done to allow the low data rate Bluetooth data to coexist in the same interface as the higher speed I2S data. To accomplish this, the Bluetooth data is repeated six times for 8 kHz data and three times for 16 kHz data. An initial sync pulse on the PCM_SYNC line is used to indicate the beginning of the frame. To support multiple Bluetooth audio streams within the Bluetooth channel, both 16 kHz and 8 kHz streams can be multiplexed. This mode of operation is only supported when the Bluetooth host is the master. Figure 12 shows the operation of the multiplexed transport with three simultaneous SCO connections. To accommodate additional SCO channels, the transport clock speed is increased. To change between modes of operation, the transport must be halted and restarted in the new configuration. Figure 12. Functional Multiplex Data Diagram 1 Frame BT SCO 1 Rx BT SCO 2 Rx BT SCO 3 Rx PCM_OUT BT SCO 1 Tx BT SCO 2 Tx FM Right FM Left FM Right FM Left 16 bits per frame 16 bits per frame BT SCO 3 Tx PCM_IN PCM_SYNC CLK PCM_CLK 16 bits per SCO frame Each SCO channel duplicates the data 6 times. Each WBS frame duplicates the data three times per frame 7.3.6 Burst PCM Mode In this mode of operation, the PCM bus runs at a significantly higher rate of operation to allow the host to duty cycle its operation and save current. In this mode of operation, the PCM bus can operate at a rate of up to 24 MHz. This mode of operation is initiated with an HCI command from the host. Document Number: 002-15053 Rev. *D Page 29 of 155 ADVANCE CYW4356 7.3.7 PCM Interface Timing Short Frame Sync, Master Mode Figure 13. PCM Timing Diagram (Short Frame Sync, Master Mode) 1 2 3 PCM_BCLK 4 PCM_SYNC 8 PCM_OUT HIGH IMPEDANCE 5 7 6 PCM_IN Table 8. PCM Interface Timing Specifications (Short Frame Sync, Master Mode) Ref No. 1 Characteristics PCM bit clock frequency Minimum – Typical – Maximum 12 Unit MHz 2 PCM bit clock LOW 41 – – ns 3 PCM bit clock HIGH 41 – – ns 4 PCM_SYNC delay 0 – 25 ns 5 PCM_OUT delay 0 – 25 ns 6 PCM_IN setup 8 – – ns 7 PCM_IN hold 8 – – ns 8 Delay from rising edge of PCM_BCLK during last bit period to PCM_OUT becoming high impedance 0 – 25 ns Document Number: 002-15053 Rev. *D Page 30 of 155 ADVANCE CYW4356 Short Frame Sync, Slave Mode Figure 14. PCM Timing Diagram (Short Frame Sync, Slave Mode) 1 2 3 PCM_BCLK 4 5 PCM_SYNC 9 PCM_OUT HIGH IMPEDANCE 6 8 7 PCM_IN Table 9. PCM Interface Timing Specifications (Short Frame Sync, Slave Mode) Ref No. Characteristics Minimum Typical Maximum Unit 1 PCM bit clock frequency – – 12 MHz 2 PCM bit clock LOW 41 – – ns 3 PCM bit clock HIGH 41 – – ns 4 PCM_SYNC setup 8 – – ns 5 PCM_SYNC hold 8 – – ns 6 PCM_OUT delay 0 – 25 ns 7 PCM_IN setup 8 – – ns 8 PCM_IN hold 8 – – ns 9 Delay from rising edge of PCM_BCLK during last bit period to PCM_OUT becoming high impedance 0 – 25 ns Document Number: 002-15053 Rev. *D Page 31 of 155 ADVANCE CYW4356 Long Frame Sync, Master Mode Figure 15. PCM Timing Diagram (Long Frame Sync, Master Mode) 1 2 3 PCM_BCLK 4 PCM_SYNC 8 PCM_OUT Bit 0 Bit 1 Bit 0 Bit 1 HIGH IMPEDANCE 5 6 PCM_IN 7 Table 10. PCM Interface Timing Specifications (Long Frame Sync, Master Mode) Ref No. Characteristics Minimum Typical Maximum Unit 1 PCM bit clock frequency – – 12 MHz 2 PCM bit clock LOW 41 – – ns 3 PCM bit clock HIGH 41 – – ns 4 PCM_SYNC delay 0 – 25 ns 5 PCM_OUT delay 0 – 25 ns 6 PCM_IN setup 8 – – ns 7 PCM_IN hold 8 – – ns 8 Delay from rising edge of PCM_BCLK during last bit period to PCM_OUT becoming high impedance 0 – 25 ns Document Number: 002-15053 Rev. *D Page 32 of 155 ADVANCE CYW4356 Long Frame Sync, Slave Mode Figure 16. PCM Timing Diagram (Long Frame Sync, Slave Mode) 1 2 3 PCM_BCLK 4 5 PCM_SYNC 9 Bit 0 PCM_OUT HIGH IMPEDANCE Bit 1 6 7 PCM_IN Bit 0 8 Bit 1 Table 11. PCM Interface Timing Specifications (Long Frame Sync, Slave Mode) Ref No. Characteristics Minimum Typical Maximum Unit 1 PCM bit clock frequency – – 12 MHz 2 PCM bit clock LOW 41 – – ns 3 PCM bit clock HIGH 41 – – ns 4 PCM_SYNC setup 8 – – ns 5 PCM_SYNC hold 8 – – ns 6 PCM_OUT delay 0 – 25 ns 7 PCM_IN setup 8 – – ns 8 PCM_IN hold 8 – – ns 9 Delay from rising edge of PCM_BCLK during last bit period to PCM_OUT becoming high impedance 0 – 25 ns Document Number: 002-15053 Rev. *D Page 33 of 155 ADVANCE CYW4356 Short Frame Sync, Burst Mode Figure 17. PCM Burst Mode Timing (Receive Only, Short Frame Sync) 1 2 3 PCM_BCLK 4 5 PCM_SYNC 6 7 PCM_IN Table 12. PCM Burst Mode (Receive Only, Short Frame Sync) Ref No. Characteristics Minimum Typical Maximum Unit 1 PCM bit clock frequency – – 24 MHz 2 PCM bit clock LOW 20.8 – – ns 3 PCM bit clock HIGH 20.8 – – ns 4 PCM_SYNC setup 8 – – ns 5 PCM_SYNC hold 8 – – ns 6 PCM_IN setup 8 – – ns 7 PCM_IN hold 8 – – ns Document Number: 002-15053 Rev. *D Page 34 of 155 ADVANCE CYW4356 Long Frame Sync, Burst Mode Figure 18. PCM Burst Mode Timing (Receive Only, Long Frame Sync) 1 3 2 PCM_BCLK 4 5 PCM_SYNC 6 PCM_IN Bit 0 7 Bit 1 Table 13. PCM Burst Mode (Receive Only, Long Frame Sync) Ref No. Characteristics Minimum Typical Maximum Unit 1 PCM bit clock frequency – – 24 MHz 2 3 PCM bit clock LOW 20.8 – – ns PCM bit clock HIGH 20.8 – – ns 4 PCM_SYNC setup 8 – – ns 5 PCM_SYNC hold 8 – – ns 6 PCM_IN setup 8 – – ns 7 PCM_IN hold 8 – – ns Document Number: 002-15053 Rev. *D Page 35 of 155 ADVANCE CYW4356 7.4 USB Interface 7.4.1 Features The following USB interface features are supported: ■ USB Protocol, Revision 2.0, full-speed (12 Mbps) compliant including the hub ■ Optional hub compound device with up to three device cores internal to device ■ Bus or self-power, dynamic configuration for the hub ■ Global and selective suspend and resume with remote wakeup ■ Bluetooth HCI ■ HID, DFU, UHE (proprietary method to emulate an HID device at system bootup) ■ Integrated detach resistor 7.4.2 Operation When the A4WP feature is not used and USB is selected as the Bluetooth interface to the host, an external pull-up (outside the chip) 10 KΩ resistor to BT_VDDIO is required. The pull-up is not necessary but is recommended when the Bluetooth/host interface is UART instead of USB. The CYW4356 can be configured to boot up as either a single USB peripheral or a USB hub with several USB peripherals attached. As a single peripheral, the host detects a single USB Bluetooth device. In hub mode, the host detects a hub with one to three of the ports already connected to USB devices (see Figure 19). Figure 19. USB Compounded Device Configuration Host USB Compounded Device Hub Controller USB Device 1 HID Keyboard USB Device 2 HID Mouse USB Device 3 Bluetooth Depending on the desired hub mode configuration, the CYW4356 can boot up showing the three ports connected to logical USB devices internal to the CYW4356: a generic Bluetooth device, a mouse, and a keyboard. In this mode, the mouse and keyboard are emulated devices, since they connect to real HID devices via a Bluetooth link. The Bluetooth link to these HID devices is hidden from the USB host. To the host, the mouse and/or keyboard appear to be directly connected to the USB port. This Cypress proprietary architecture is called USB HID Emulation (UHE). The USB device, configuration, and string descriptors are fully programmable, allowing manufacturers to customize the descriptors, including vendor and product IDs, the CYW4356 uses to identify itself on the USB port. To make custom USB descriptor information available at boot time, stored it in external NVRAM. Despite the mode of operation (single peripheral or hub), the Bluetooth device is configured to include the following interfaces: Interface 0 Contains a Control endpoint (Endpoint 0x00) for HCI commands, a Bulk In Endpoint (Endpoint 0x82) for receiving ACL data, a Bulk Out Endpoint (Endpoint 0x02) for transmitting ACL data, and an Interrupt Endpoint (Endpoint 0x81) for HCI events. Interface 1 Contains Isochronous In and Out endpoints (Endpoints 0x83 and 0x03) for SCO traffic. Several alternate Interface 1 settings are available for reserving the proper bandwidth of isochronous data (depending on the application). Interface 2 Contains Bulk In and Bulk Out endpoints (Endpoints 0x84 and 0x04) used for proprietary testing and debugging purposes. These endpoints can be ignored during normal operation. Document Number: 002-15053 Rev. *D Page 36 of 155 ADVANCE CYW4356 7.4.3 USB Hub and UHE Support The CYW4356 supports the USB hub and device model (USB, Revision 2.0, full-speed compliant). Optional mouse and keyboard devices utilize Cypress’s proprietary USB HID Emulation (UHE) architecture, which allows these devices appear as standalone HID devices even though connected through a Bluetooth link. The presence of UHE devices requires the hub to be enabled. The CYW4356 cannot appear as a single keyboard or a single mouse device without the hub. Once either mouse or keyboard UHE device is enabled, the hub must also be enabled. When the hub is enabled, the CYW4356 handles all standard USB functions for the following devices: ■ HID keyboard ■ HID mouse ■ Bluetooth All hub and device descriptors are firmware-programmable. This USB compound device configuration (see Figure 19) supports up to three downstream ports. This configuration can also be programmed to a single USB device core. The device automatically detects activity on the USB interface when connected. Therefore, no special configuration is needed to select HCI as the transport. The hub’s downstream port definition is as follows: ■ Port 1 USB lite device core (for HID applications) ■ Port 2 USB lite device core (for HID applications) ■ Port 3 USB full device core (for Bluetooth applications) When operating in hub mode, all three internal devices do not have to be enabled. Each internal USB device can be optionally enabled. The configuration record in NVRAM determines which devices are present. 7.4.4 USB Full-Speed Timing Table 14 shows timing specifications for the VDD_USB = 3.3V, VSS = 0V, and TA = 0°C to 85°C operating temperature range. Table 14. USB Full-Speed Timing Specifications Reference Characteristics Minimum Maximum Unit 1 Transition rise time 4 20 ns 2 Transition fall time 4 20 ns 3 Rise/fall timing matching 90 111 % 4 Full-speed data rate 12 – 0.25% 12 + 0.25% Mb/s Figure 20. USB Full-Speed Timing 2 1 D+ 90% 90% VCRS 10% 10% D- Document Number: 002-15053 Rev. *D Page 37 of 155 ADVANCE CYW4356 7.5 UART Interface The CYW4356 shares a single UART for Bluetooth and FM. The UART is a standard 4-wire interface (RX, TX, RTS, and CTS) with adjustable baud rates from 9600 bps to 4.0 Mbps. The interface features an automatic baud rate detection capability that returns a baud rate selection. Alternatively, the baud rate may be selected through a vendor-specific UART HCI command. UART has a 1040-byte receive FIFO and a 1040-byte transmit FIFO to support EDR. Access to the FIFOs is conducted through the AHB interface through either DMA or the CPU. The UART supports the Bluetooth 4.1 UART HCI specification: H4, a custom Extended H4, and H5. The default baud rate is 115.2 Kbaud. The UART supports the 3-wire H5 UART transport, as described in the Bluetooth specification (“Three-wire UART Transport Layer”). Compared to H4, the H5 UART transport reduces the number of signal lines required by eliminating the CTS and RTS signals. The CYW4356 UART can perform XON/XOFF flow control and includes hardware support for the Serial Line Input Protocol (SLIP). It can also perform wake-on activity. For example, activity on the RX or CTS inputs can wake the chip from a sleep state. Normally, the UART baud rate is set by a configuration record downloaded after device reset, or by automatic baud rate detection, and the host does not need to adjust the baud rate. Support for changing the baud rate during normal HCI UART operation is included through a vendor-specific command that allows the host to adjust the contents of the baud rate registers. The CYW4356 UARTs operate correctly with the host UART as long as the combined baud rate error of the two devices is within ±2%. Table 15. Example of Common Baud Rates Desired Rate Actual Rate Error (%) 4000000 4000000 0.00 3692000 3692308 0.01 3000000 3000000 0.00 2000000 2000000 0.00 1500000 1500000 0.00 1444444 1454544 0.70 921600 923077 0.16 460800 461538 0.16 230400 230796 0.17 115200 115385 0.16 57600 57692 0.16 38400 38400 0.00 28800 28846 0.16 19200 19200 0.00 14400 14423 0.16 9600 9600 0.00 Document Number: 002-15053 Rev. *D Page 38 of 155 ADVANCE CYW4356 Figure 21. UART Timing UART_CTS_N 1 2 UART_TXD Midpoint of STOP bit Midpoint of STOP bit UART_RXD 3 UART_RTS_N Table 16. UART Timing Specifications Ref No. Characteristics Min. Typ. Max. Unit 1 Delay time, UART_CTS_N low to UART_TXD valid – – 1.5 Bit periods 2 Setup time, UART_CTS_N high before midpoint of stop bit – – 0.5 Bit periods 3 Delay time, midpoint of stop bit to UART_RTS_N high – – 0.5 Bit periods 7.6 I2S Interface The CYW4356 supports two independent I2S digital audio ports: one for Bluetooth audio, and one for high-fidelity FM audio. The I2S interface for FM audio supports both master and slave modes. The I2S signals are: ■ I2S clock: BT_I2S_CLK ■ I2S Word Select: BT_I2S_WS ■ I2S Data Out: BT_I2S_DO ■ I2S Data In: BT_I2S_DI BT_I2S_CLK and BT_I2S_WS become outputs in master mode and inputs in slave mode, whereas BT_I2S_DO always stays as an output. The channel word length is 16 bits, and the data is justified so that the MSB of the left-channel data is aligned with the MSB of the I2S bus, in accord with the I2S specification. The MSB of each data word is transmitted one bit clock cycle after the BT_I2S_WS transition, synchronous with the falling edge of the bit clock. Left-channel data is transmitted when IBT_I2S_WS is low, and rightchannel data is transmitted when BT_I2S_WS is high. Data bits sent by the CYW4356 are synchronized with the falling edge of BT_I2S_CLK and should be sampled by the receiver on the rising edge of BT_I2S_CLK. The clock rate in master mode is either of the following: 48 kHz x 32 bits per frame = 1.536 MHz 48 kHz x 50 bits per frame = 2.400 MHz The master clock is generated from the input reference clock using a N/M clock divider. In the slave mode, any clock rate is supported to a maximum of 3.072 MHz. Document Number: 002-15053 Rev. *D Page 39 of 155 ADVANCE CYW4356 7.6.1 I2S Timing Note: Timing values specified in Table 17 are relative to high and low threshold levels. Table 17. Timing for I2S Transmitters and Receivers Transmitter Lower LImit Min. Clock Period T Ttr Upper Limit Max. – Receiver Min. – Lower Limit Max. Min. Upper Limit Max. Min. Notes Max. – Tr – – – a Master Mode: Clock generated by transmitter or receiver HIGH tHC 0.35Ttr – – – 0.35Ttr – – – b LOWtLC 0.35Ttr – – – 0.35Ttr – – – b Slave Mode: Clock accepted by transmitter or receiver HIGH tHC – 0.35Ttr – – – 0.35Ttr – – c LOW tLC – 0.35Ttr – – – 0.35Ttr – – c Rise time tRC – – 0.15Ttr – – – – d Delay tdtr – – – 0.8T – – – – e Hold time thtr 0 – – – – – – – d Setup time tsr – – – – – 0.2Tr – – f Hold time thr – – – – – 0 – – f Transmitter Receiver a. The system clock period T must be greater than Ttr and Tr because both the transmitter and receiver have to be able to handle the data transfer rate. b. At all data rates in master mode, the transmitter or receiver generates a clock signal with a fixed mark/space ratio. For this reason, tHC and tLC are specified with respect to T. c. In slave mode, the transmitter and receiver need a clock signal with minimum HIGH and LOW periods so that they can detect the signal. So long as the minimum periods are greater than 0.35Tr, any clock that meets the requirements can be used. d. Because the delay (tdtr) and the maximum transmitter speed (defined by Ttr) are related, a fast transmitter driven by a slow clock edge can result in tdtr not exceeding tRC which means thtr becomes zero or negative. Therefore, the transmitter has to guarantee that thtr is greater than or equal to zero, so long as the clock rise-time tRC is not more than tRCmax, where tRCmax is not less than 0.15Ttr. e. To allow data to be clocked out on a falling edge, the delay is specified with respect to the rising edge of the clock signal and T, always giving the receiver sufficient setup time. f. The data setup and hold time must not be less than the specified receiver setup and hold time. Document Number: 002-15053 Rev. *D Page 40 of 155 ADVANCE CYW4356 Note: The time periods specified in Figure 22 and Figure 23 are defined by the transmitter speed. The receiver specifications must match transmitter performance. Figure 22. I2S Transmitter Timing T tRC* tLC > 0.35T tHC > 0.35T V H = 2.0V SCK V L = 0.8V thtr > 0 totr < 0.8T SD and WS T = Clock period Ttr = Minimum allowed clock period for transmitter T = Ttr * tRC is only relevant for transmitters in slave mode. Figure 23. I2S Receiver Timing T tLC > 0.35T tHC > 0.35 VH = 2.0V SCK VL = 0.8V tsr > 0.2T thr > 0 SD and WS T = Clock period Tr = Minimum allowed clock period for transmitter T > Tr Document Number: 002-15053 Rev. *D Page 41 of 155 ADVANCE CYW4356 8. FM Receiver Subsystem 8.1 FM Radio The CYW4356 includes a completely integrated FM radio receiver with RDS/RBDS covering all FM bands from 65 MHz to 108 MHz. The receiver is controlled through commands on the HCI. FM received audio is available as stereo or in digital form through I2S or PCM. The FM radio operates from the external clock reference. 8.2 Digital FM Audio Interfaces The FM audio can be transmitted via the shared PCM and I2S pins, and the sampling rate is programmable. The CYW4356 supports a three-wire PCM or I2S audio interface in either master or slave configuration. The master or slave configuration is selected using vendor specific commands over the HCI interface. In addition, multiple sampling rates are supported, derived from either the FM or Bluetooth clocks. In master mode, the clock rate is either of the following: ■ 48 kHz × 32 bits per frame = 1.536 MHz ■ 48 kHz × 50 bits per frame = 2.400 MHz In slave mode, any clock rate is supported up to a maximum of 3.072 MHz. 8.3 FM Over Bluetooth The CYW4356 can output received FM audio onto Bluetooth using one of following three links: eSCO, WBS, and A2DP. In all of the above modes, once the link has been set up, the host processor can enter sleep mode while the CYW4356 continues to stream FM audio to the remote Bluetooth device, allowing the system current consumption to be minimized. 8.4 eSCO In this use case, the stereo FM audio is downsampled to 8 kHz and a mono or stereo stream is then sent through the Bluetooth eSCO link to a remote Bluetooth device, typically a headset. Two Bluetooth voice connections must be used to transport stereo. 8.5 Wideband Speech Link In this case, the stereo FM audio is downsampled to 16 kHz and a mono or stereo stream is then sent through the Bluetooth wideband speech link to a remote Bluetooth device, typically a headset. Two Bluetooth voice connections must be used to transport stereo. 8.6 A2DP In this case, the stereo FM audio is encoded by the on-chip SBC encoder and transported as an A2DP link to a remote Bluetooth device. Sampling rates of 48 kHz, 44.1 kHz, and 32 kHz joint stereo are supported. An A2DP “lite” stack is implemented in the CYW4356 to support this use case, which eliminates the need to route the SBC-encoded audio back to the host to create the A2DP packets. 8.7 Autotune and Search Algorithms The CYW4356 supports a number of FM search and tune functions that allows the host to implement many convenient user functions, which are accessed through the Cypress FM stack. ■ Tune to Play: Allows the FM receiver to be programmed to a specific frequency. ■ Search for SNR > Threshold: Checks the power level of the available channel and the estimated SNR of the channel to help achieve precise control of the expected sound quality for the selected FM channel. Specifically, the host can adjust its SNR requirements to retrieve a signal with a specific sound quality, or adjust this to return the weakest channels. ■ Alternate Frequency Jump: Allows the FM receiver to automatically jump to an alternate FM channel that carries the same information, but has a better SNR. For example, when traveling, a user may pass through a region where a number of channels carry the same station. When the user passes from one area to the next, the FM receiver can automatically switch to another channel with a stronger signal to spare the user from having to manually change the channel to continue listening to the same station. Document Number: 002-15053 Rev. *D Page 42 of 155 ADVANCE CYW4356 8.8 Audio Features A number of features are implemented in the CYW4356 to provide the best possible audio experience for the user. ■ Mono/Stereo Blend or Switch: The CYW4356 provides automatic control of the stereo or mono settings based on the FM signal carrier-to-noise ratio (C/N). This feature is used to maintain the best possible audio SNR based on the FM channel condition. Two modes of operation are supported: ❐ Blend: In this mode, fine control of stereo separation is used to achieve optimal audio quality over a wide range of input C/N. The amount of separation is fully programmable. In Figure 24, the separation is programmed to maintain a minimum 50 dB SNR across the blend range. ❐ Extended blend: In this mode, stereo separation is maximized across a wide range of input CNR. Cypress static suppression typically gives a static-free user experience to within 3 dB of ultimate sensitivity. Figure 24. Example Blend/Switch Usage Document Number: 002-15053 Rev. *D Page 43 of 155 ADVANCE ❐ CYW4356 Switch: In this mode, the audio switches from full stereo to full mono at a predetermined level to maintain optimal audio quality. The stereo-to-mono switch point and the mono-to-stereo switch points are fully programmable to provide the desired amount of audio SNR. In Figure 25, the switch point is programmed to switch to mono to maintain a 40 dB SNR. Figure 25. Example Blend/Switch Separation ■ Soft Mute: Improves the user experience by dynamically muting the output audio proportionate to the FM signal C/N. This prevents the user from being assaulted with a blast of static. The mute characteristic is fully programmable to accommodate fine tuning of the output signal level. An example mute characteristic is shown in Figure 26. Figure 26. Example Soft Mute Characteristic Document Number: 002-15053 Rev. *D Page 44 of 155 ADVANCE CYW4356 ■ High Cut: A programmable high-cut filter is provided to reduce the amount of high-frequency noise caused by static in the output audio signal. Like the soft mute circuit, it is fully programmable to allow for any amount of high cut based on the FM signal C/N. ■ Audio Pause Detect: The FM receiver monitors the magnitude of the audio signal and notifies the host through an interrupt when the magnitude of the signal has fallen below the threshold set for a programmable period. This feature can be used to provide alternate frequency jumps during periods of silence to minimize disturbances to the listener. Filtering techniques are used within the audio pause detection block to provide more robust presence-to-silence detection and silence-to-presence detection. ■ Automatic Antenna Tuning: The CYW4356 has an on-chip automatic antenna tuning network. When used with a single off-chip inductor, the on-chip circuitry automatically chooses an optimal on-chip matching component to obtain the highest signal strength for the desired frequency. The high-Q nature of this matching network simultaneously provides out-of-band blocking protection as well as a reduction of radiated spurious emissions from the FM antenna. It is designed to accommodate a wide range of external wire antennas. 8.9 RDS/RBDS The CYW4356 integrates a RDS/RBDS modem and codec, the decoder includes programmable filtering and buffering functions, and the encoder includes the option to encode messages to PS or RT frame format with programmable scrolling in PS mode. The RDS/ RBDS data can be read out in receive mode or delivered in transmit mode through either the HCI interface. In addition, the RDS/RBDS functionality supports the following: Receive ■ Block decoding, error correction and synchronization ■ Flywheel synchronization feature, allowing the host to set parameters for acquisition, maintenance, and loss of sync. (It is possible to set up the CYW4356 such that synch is achieved when a minimum of two good blocks (error free) are decoded in sequence. The number of good blocks required for sync is programmable.) ■ Storage capability up to 126 blocks of RDS data ■ Full or partial block B match detect and interrupt to host ■ Audio pause detection with programmable parameters ■ Program Identification (PI) code detection and interrupt to host ■ Automatic frequency jump ■ Block E filtering ■ Soft mute ■ Signal dependent mono/stereo blend ■ Programmable preemphasis Document Number: 002-15053 Rev. *D Page 45 of 155 ADVANCE CYW4356 9. WLAN Global Functions 9.1 WLAN CPU and Memory Subsystem The CYW4356 WLAN section includes an integrated ARM Cortex-R4 32-bit processor with internal RAM and ROM. The ARM CortexR4 is a low-power processor that features low gate count, low interrupt latency, and low-cost debug capabilities. It is intended for deeply embedded applications that require fast interrupt response features. Delivering a performance gain of more than 30% over the ARM7TDMI processor, the ARM Cortex-R4 processor implements the ARM v7-R architecture with support for the Thumb-2 instruction set. At 0.19 µW/MHz, the Cortex-R4 is the most power efficient general-purpose microprocessor available, outperforming 8- and 16-bit devices on MIPS/µW. Using multiple technologies to reduce cost, the ARM Cortex-R4 offers improved memory utilization, reduced pin overhead, and reduced silicon area. It supports independent buses for Code and Data access (ICode/DCode and System buses), integrated sleep modes, and extensive debug features including real time trace of program execution. On-chip memory for the CPU includes 768 KB SRAM and 640 KB ROM. 9.2 One-Time Programmable Memory Various hardware configuration parameters may be stored in an internal One-Time Programmable (OTP) memory, which is read by the system software after device reset. In addition, customer-specific parameters, including the system vendor ID and the MAC address can be stored, depending on the specific board design. Up to 484 bytes of user-accessible OTP are available. The initial state of all bits in an unprogrammed OTP device is 0. After any bit is programmed to a 1, it cannot be reprogrammed to 0. The entire OTP array can be programmed in a single write cycle using a utility provided with the Cypress WLAN manufacturing test tools. Alternatively, multiple write cycles can be used to selectively program specific bytes, but only bits which are still in the 0 state can be altered during each programming cycle. Prior to OTP programming, all values should be verified using the appropriate editable nvram.txt file, which is provided with the reference board design package. 9.3 GPIO Interface The CYW4356 has 11 general-purpose I/O (GPIO) pins in the WLAN section that can be used to connect to various external devices. Upon power-up and reset, these pins become tristated. Subsequently, they can be programmed to be either input or output pins via the GPIO control register. In addition, the GPIO pins can be assigned to various other functions, see Table 27. Document Number: 002-15053 Rev. *D Page 46 of 155 ADVANCE CYW4356 9.4 External Coexistence Interface An external handshake interface is available to enable signaling between the device and an external co-located wireless device, such as GPS, LTE, or UWB, to manage wireless medium sharing for optimal performance. Figure 27 and Figure 28 show the LTE coexistence interface (including UART) for each CYW4356 package type. See Table 27 for further details on multiplexed signals, such as the GPIO pins. See Table 16 for the UART baud rate. Figure 27. Cypress GCI Mode LTE Coexistence Interface SECI_OUT WLAN SECI_IN UART_IN UART_OUT GCI BTFM CYW4356 LTE/IC Notes: OR’ing to generate ISM_RX_PRIORITY for ERCX_TXCONF or BT_RX_PRIORITY is achieved by setting the GPIO mask registers appropriately. SECI_OUT and SECI_IN are multiplexed on the GPIOs. Figure 28. Legacy 3-Wire LTE Coexistence Interface GCI_GPIO_2 WLAN WCN_PRIORITY GCI_GPIO_1 GCI MWS_RX, LTE_PRIORITY GCI_GPIO_0 LTE_FRAME_SYNC BT/FM CYW4356 LTE/IC Note: OR’ing to generate WCN_PRIORITY FOR ERCX_TXCONF or BT_RX_PRIORITY is achieved by setting the GPIO mask registers appropriately. Document Number: 002-15053 Rev. *D Page 47 of 155 ADVANCE CYW4356 9.5 UART Interface One 2-wire UART interface can be enabled by software as an alternate function on GPIO pins. Refer to Table 27. Provided primarily for debugging during development, this UART enables the CYW4356 to operate as RS-232 data termination equipment (DTE) for exchanging and managing data with other serial devices. It is compatible with the industry standard 16550 UART, and provides a FIFO size of 64 × 8 in each direction. 9.6 JTAG Interface The CYW4356 supports the IEEE 1149.1 JTAG boundary scan standard for performing device package and PCB assembly testing during manufacturing. In addition, the JTAG interface allows Cypress to assist customers by using proprietary debug and characterization test tools during board bring-up. Therefore, it is highly recommended to provide access to the JTAG pins by means of test points or a header on all PCB designs. Refer to Table 27 for JTAG pin assignments. 9.7 SPROM Interface Various hardware configuration parameters may be stored in an external SPROM instead of the OTP. The SPROM is read by system software after device reset. In addition, depending on the board design, customer-specific parameters may be stored in SPROM. The four SPROM control signals —SPROM_CS, SPROM_CLK, SPROM_MI, and SPROM_MO are multiplexed on the SDIO interface (see Table 27 for additional details). By default, the SPROM interface supports 2 Kbit serial SPROMs, and it can also support 4 Kbit and 16 Kbit serial SPROMs by using the appropriate strapping option. Document Number: 002-15053 Rev. *D Page 48 of 155 ADVANCE CYW4356 10. WLAN Host Interfaces 10.1 SDIO v3.0 All three package options of the CYW4356 WLAN section provide support for SDIO version 3.0, including the new UHS-I modes: ■ DS: Default speed (DS) up to 25 MHz, including 1- and 4-bit modes (3.3V signaling). ■ HS: High-speed up to 50 MHz (3.3V signaling). ■ SDR12: SDR up to 25 MHz (1.8V signaling). ■ SDR25: SDR up to 50 MHz (1.8V signaling). ■ SDR50: SDR up to 100 MHz (1.8V signaling). ■ SDR104: SDR up to 208 MHz (1.8V signaling) ■ DDR50: DDR up to 50 MHz (1.8V signaling). Note: The CYW4356 is backward compatible with SDIO v2.0 host interfaces. The SDIO interface also has the ability to map the interrupt signal on to a GPIO pin for applications requiring an interrupt different from the one provided by the SDIO interface. The ability to force control of the gated clocks from within the device is also provided. SDIO mode is enabled by strapping options. Refer to Table 24 WLAN GPIO Functions and Strapping Options. The following three functions are supported: ■ Function 0 Standard SDIO function (max. BlockSize/ByteCount = 32B) ■ Function 1 Backplane Function to access the internal system-on-chip (SoC) address space (max. BlockSize/ByteCount = 64B) ■ Function 2 WLAN Function for efficient WLAN packet transfer through DMA (max. BlockSize/ByteCount = 512B) 10.1.1 SDIO Pins Table 18. SDIO Pin Descriptions SD 4-Bit Mode SD 1-Bit Mode DATA0 Data line 0 DATA Data line DATA1 Data line 1 or Interrupt IRQ Interrupt DATA2 Data line 2 or Read Wait RW Read Wait DATA3 Data line 3 N/C Not used CLK Clock CLK Clock CMD Command line CMD Command line Figure 29. Signal Connections to SDIO Host (SD 4-Bit Mode) CLK SD Host CMD CYW4356 DAT[3:0] Document Number: 002-15053 Rev. *D Page 49 of 155 ADVANCE CYW4356 Figure 30. Signal Connections to SDIO Host (SD 1-Bit Mode) CLK CMD SD Host DATA CYW4356 IRQ RW Note: Per Section 6 of the SDIO specification, pull-ups in the 10 kΩ to 100 kΩ range are required on the four DATA lines and the CMD line. This requirement must be met during all operating states either through the use of external pull-up resistors or through proper programming of the SDIO host’s internal pull-ups. Document Number: 002-15053 Rev. *D Page 50 of 155 ADVANCE CYW4356 10.2 PCI Express Interface The PCI Express (PCIe) core on the CYW4356 is a high-performance serial I/O interconnect that is protocol compliant and electrically compatible with the PCI Express Base Specification v3.0 running at Gen1 speeds. This core contains all the necessary blocks, including logical and electrical functional subblocks to perform PCIe functionality and maintain high-speed links, using existing PCI system configuration software implementations without modification. Organization of the PCIe core is in logical layers: Transaction Layer, Data Link Layer, and Physical Layer, as shown in Figure 31. A configuration or link management block is provided for enumerating the PCIe configuration space and supporting generation and reception of System Management Messages by communicating with PCIe layers. Each layer is partitioned into dedicated transmit and receive units that allow point-to-point communication between the host and CYW4356 device. The transmit side processes outbound packets whereas the receive side processes inbound packets. Packets are formed and generated in the Transaction and Data Link Layer for transmission onto the high-speed links and onto the receiving device. A header is added at the beginning to indicate the packet type and any other optional fields. Figure 31. PCI Express Layer Model HW/SW Interface HW/SW Interface Transaction Layer Transaction Layer Data Link Layer Data Link Layer Physical Layer Physical Layer Logical Subblock Logical Subblock Electrical Subblock Electrical Subblock TX RX TX RX 10.2.1 Transaction Layer Interface The PCIe core employs a packet-based protocol to transfer data between the host and CYW4356 device, delivering new levels of performance and features. The upper layer of the PCIe is the Transaction Layer. The Transaction layer is primarily responsible for assembly and disassembly of Transaction Layer Packets (TLPs). TLP structure contains header, data payload, and End-to-End CRC (ECRC) fields, which are used to communicate transactions, such as read and write requests and other events. A pipelined full split-transaction protocol is implemented in this layer to maximize efficient communication between devices with creditbased flow control of TLP, which eliminates wasted link bandwidth due to retries. 10.2.2 Data Link Layer The data link layer serves as an intermediate stage between the transaction layer and the physical layer. Its primary responsibility is to provide reliable, efficient mechanism for the exchange of TLPs between two directly connected components on the link. Services provided by the data link layer include data exchange, initialization, error detection and correction, and retry services. Data Link Layer Packets (DLLPs) are generated and consumed by the data link layer. DLLPs are the mechanism used to transfer link management information between data link layers of the two directly connected components on the link, including TLP acknowledgement, power management, and flow control. Document Number: 002-15053 Rev. *D Page 51 of 155 ADVANCE CYW4356 10.2.3 Physical Layer The physical layer of the PCIe provides a handshake mechanism between the data link layer and the high-speed signaling used for Link data interchange. This layer is divided into the logical and electrical functional subblocks. Both subblocks have dedicated transmit and receive units that allow for point-to-point communication between the host and CYW4356 device. The transmit section prepares outgoing information passed from the data link layer for transmission, and the receiver section identifies and prepares received information before passing it to the data link layer. This process involves link initialization, configuration, scrambler, and data conversion into a specific format. 10.2.4 Logical Subblock The logical sub block primary functions are to prepare outgoing data from the data link layer for transmission and identify received data before passing it to the data link layer. 10.2.5 Scrambler/Descrambler This PCIe PHY component generates pseudo-random sequence for scrambling of data bytes and the idle sequence. On the transmit side, scrambling is applied to characters prior to the 8b/10b encoding. On the receive side, descrambling is applied to characters after 8b/10b decoding. Scrambling may be disabled in polling and recovery for testing and debugging purposes. 10.2.6 8B/10B Encoder/Decoder The PCIe core on the CYW4356 uses an 8b/10b encoder/decoder scheme to provide DC balancing, synchronizing clock and data recovery, and error detection. The transmission code is specified in the ANSI X3.230-1994, clause 11 and in IEEE 802.3z, 36.2.4. Using this scheme, 8-bit data characters are treated as 3 bits and 5 bits mapped onto a 4-bit code group and a 6-bit code group, respectively. The control bit in conjunction with the data character is used to identify when to encode one of the twelve Special Symbols included in the 8b/10b transmission code. These code groups are concatenated to form a 10-bit symbol, which is then transmitted serially. Special Symbols are used for link management, frame TLPs, and DLLPs, allowing these packets to be quickly identified and easily distinguished. 10.2.7 Elastic FIFO An elastic FIFO is implemented in the receiver side to compensate for the differences between the transmit clock domain and the receive clock domain, with worse case clock frequency specified at 600 ppm tolerance. As a result, the transmit and receive clocks can shift one clock every 1666 clocks. In addition, the FIFO adaptively adjusts the elastic level based on the relative frequency difference of the write and read clock. This technique reduces the elastic FIFO size and the average receiver latency by half. 10.2.8 Electrical Subblock The high-speed signals utilize the Common Mode Logic (CML) signaling interface with on-chip termination and de-emphasis for bestin-class signal integrity. A de-emphasis technique is employed to reduce the effects of Intersymbol Interference (ISI) due to the interconnect by optimizing voltage and timing margins for worst case channel loss. This results in a maximally open “eye” at the detection point, thereby allowing the receiver to receive data with acceptable Bit-Error Rate (BER). To further minimize ISI, multiple bits of the same polarity that are output in succession are de-emphasized. Subsequent same bits are reduced by a factor of 3.5 dB in power. This amount is specified by PCIe to allow for maximum interoperability while minimizing the complexity of controlling the de-emphasis values. The high-speed interface requires AC coupling on the transmit side to eliminate the DC common mode voltage from the receiver. The range of AC capacitance allowed is 75 nF to 200 nF. 10.2.9 Configuration Space The PCIe function in the CYW4356 implements the configuration space as defined in the PCI Express Base Specification v3.0. Document Number: 002-15053 Rev. *D Page 52 of 155 ADVANCE CYW4356 11. Wireless LAN MAC and PHY 11.1 IEEE 802.11ac Draft MAC The CYW4356 WLAN MAC is designed to support high-throughput operation with low-power consumption. It does so without compromising the Bluetooth coexistence policies, thereby enabling optimal performance over both networks. In addition, several power saving modes have been implemented that allow the MAC to consume very little power while maintaining network-wide timing synchronization. The architecture diagram of the MAC is shown in Figure 32. The following sections provide an overview of the important modules in the MAC. Figure 32. WLAN MAC Architecture Embedded CPU Interface Host Registers, DMA Engines TX‐FIFO 32 KB PMQ RX‐FIFO 10 KB PSM PSM UCODE Memory IFS Backoff, BTCX WEP TKIP, AES, WAPI TSF SHM BUS IHR NAV BUS EXT‐ IHR TXE TX A‐MPDU RXE RX A‐MPDU Shared Memory 6 KB MAC‐PHY Interface The CYW4356 WLAN media access controller (MAC) supports features specified in the IEEE 802.11 base standard, and amended by IEEE 802.11n. The key MAC features include: ■ Enhanced MAC for supporting IEEE 802.11ac Draft features ■ Transmission and reception of aggregated MPDUs (A-MPDU) for high throughput (HT) ■ Support for power management schemes, including WMM power-save, power-save multi-poll (PSMP) and multiphase PSMP operation ■ Support for immediate ACK and Block-ACK policies ■ Interframe space timing support, including RIFS ■ Support for RTS/CTS and CTS-to-self frame sequences for protecting frame exchanges ■ Back-off counters in hardware for supporting multiple priorities as specified in the WMM specification ■ Timing synchronization function (TSF), network allocation vector (NAV) maintenance, and target beacon transmission time (TBTT) generation in hardware ■ Hardware offload for AES-CCMP, legacy WPA TKIP, legacy WEP ciphers, WAPI, and support for key management ■ Support for coexistence with Bluetooth and other external radios ■ Programmable independent basic service set (IBSS) or infrastructure basic service set functionality ■ Statistics counters for MIB support Document Number: 002-15053 Rev. *D Page 53 of 155 ADVANCE CYW4356 PSM The programmable state machine (PSM) is a micro-coded engine, which provides most of the low-level control to the hardware, to implement the IEEE 802.11 specification. It is a microcontroller that is highly optimized for flow control operations, which are predominant in implementations of communication protocols. The instruction set and fundamental operations are simple and general, which allows algorithms to be optimized until very late in the design process. It also allows for changes to the algorithms to track evolving IEEE 802.11 specifications. The PSM fetches instructions from the microcode memory. It uses the shared memory to obtain operands for instructions, as a data store, and to exchange data between both the host and the MAC data pipeline (via the SHM bus). The PSM also uses a scratchpad memory (similar to a register bank) to store frequently accessed and temporary variables. The PSM exercises fine-grained control over the hardware engines, by programming internal hardware registers (IHR). These IHRs are co-located with the hardware functions they control, and are accessed by the PSM via the IHR bus. The PSM fetches instructions from the microcode memory using an address determined by the program counter, instruction literal, or a program stack. For ALU operations the operands are obtained from shared memory, scratchpad, IHRs, or instruction literals, and the results are written into the shared memory, scratchpad, or IHRs. There are two basic branch instructions: conditional branches and ALU based branches. To better support the many decision points in the IEEE 802.11 algorithms, branches can depend on either a readily available signals from the hardware modules (branch condition signals are available to the PSM without polling the IHRs), or on the results of ALU operations. WEP The wired equivalent privacy (WEP) engine encapsulates all the hardware accelerators to perform the encryption and decryption, and MIC computation and verification. The accelerators implement the following cipher algorithms: legacy WEP, WPA TKIP, WPA2 AESCCMP. The PSM determines, based on the frame type and association information, the appropriate cipher algorithm to be used. It supplies the keys to the hardware engines from an on-chip key table. The WEP interfaces with the TXE to encrypt and compute the MIC on transmit frames, and the RXE to decrypt and verify the MIC on receive frames. TXE The transmit engine (TXE) constitutes the transmit data path of the MAC. It coordinates the DMA engines to store the transmit frames in the TXFIFO. It interfaces with WEP module to encrypt frames, and transfers the frames across the MAC-PHY interface at the appropriate time determined by the channel access mechanisms. The data received from the DMA engines are stored in transmit FIFOs. The MAC supports multiple logical queues to support traffic streams that have different QoS priority requirements. The PSM uses the channel access information from the IFS module to schedule a queue from which the next frame is transmitted. Once the frame is scheduled, the TXE hardware transmits the frame based on a precise timing trigger received from the IFS module. The TXE module also contains the hardware that allows the rapid assembly of MPDUs into an A-MPDU for transmission. The hardware module aggregates the encrypted MPDUs by adding appropriate headers and pad delimiters as needed. RXE The receive engine (RXE) constitutes the receive data path of the MAC. It interfaces with the DMA engine to drain the received frames from the RXFIFO. It transfers bytes across the MAC-PHY interface and interfaces with the WEP module to decrypt frames. The decrypted data is stored in the RXFIFO. The RXE module contains programmable filters that are programmed by the PSM to accept or filter frames based on several criteria such as receiver address, BSSID, and certain frame types. The RXE module also contains the hardware required to detect A-MPDUs, parse the headers of the containers, and disaggregate them into component MPDUS. Document Number: 002-15053 Rev. *D Page 54 of 155 ADVANCE CYW4356 IFS The IFS module contains the timers required to determine interframe space timing including RIFS timing. It also contains multiple backoff engines required to support prioritized access to the medium as specified by WMM. The interframe spacing timers are triggered by the cessation of channel activity on the medium, as indicated by the PHY. These timers provide precise timing to the TXE to begin frame transmission. The TXE uses this information to send response frames or perform transmit frame-bursting (RIFS or SIFS separated, as within a TXOP). The backoff engines (for each access category) monitor channel activity, in each slot duration, to determine whether to continue or pause the backoff counters. When the backoff counters reach 0, the TXE gets notified, so that it may commence frame transmission. In the event of multiple backoff counters decrementing to 0 at the same time, the hardware resolves the conflict based on policies provided by the PSM. The IFS module also incorporates hardware that allows the MAC to enter a low-power state when operating under the IEEE power save mode. In this mode, the MAC is in a suspended state with its clock turned off. A sleep timer, whose count value is initialized by the PSM, runs on a slow clock and determines the duration over which the MAC remains in this suspended state. Once the timer expires the MAC is restored to its functional state. The PSM updates the TSF timer based on the sleep duration ensuring that the TSF is synchronized to the network. The IFS module also contains the PTA hardware that assists the PSM in Bluetooth coexistence functions. TSF The timing synchronization function (TSF) module maintains the TSF timer of the MAC. It also maintains the target beacon transmission time (TBTT). The TSF timer hardware, under the control of the PSM, is capable of adopting timestamps received from beacon and probe response frames in order to maintain synchronization with the network. The TSF module also generates trigger signals for events that are specified as offsets from the TSF timer, such as uplink and downlink transmission times used in PSMP. NAV The network allocation vector (NAV) timer module is responsible for maintaining the NAV information conveyed through the duration field of MAC frames. This ensures that the MAC complies with the protection mechanisms specified in the standard. The hardware, under the control of the PSM, maintains the NAV timer and updates the timer appropriately based on received frames. This timing information is provided to the IFS module, which uses it as a virtual carrier-sense indication. MAC-PHY Interface The MAC-PHY interface consists of a data path interface to exchange RX/TX data from/to the PHY. In addition, there is an programming interface, which can be controlled either by the host or the PSM to configure and control the PHY. 11.2 IEEE 802.11ac Draft PHY The CYW4356 WLAN Digital PHY is designed to comply with IEEE 802.11ac Draft and IEEE 802.11a/b/g/n dual-stream specifications to provide wireless LAN connectivity supporting data rates from 1 Mbps to 866.7 Mbps for low-power, high-performance handheld applications. The PHY has been designed to work in the presence of interference, radio nonlinearity, and various other impairments. It incorporates optimized implementations of the filters, FFT and Viterbi decoder algorithms. Efficient algorithms have been designed to achieve maximum throughput and reliability, including algorithms for carrier sense/rejection, frequency/phase/timing acquisition and tracking, channel estimation and tracking. The PHY receiver also contains a robust IEEE 802.11b demodulator. The PHY carrier sense has been tuned to provide high throughput for IEEE 802.11g/11b hybrid networks with Bluetooth coexistence. It has also been designed for sharing an antenna between WL and BT to support simultaneous RX-RX. The key PHY features include: ■ Programmable data rates from MCS0–15 in 20 MHz, 40 MHz, and 80 MHz channels, as specified in IEEE 802.11ac Draft ■ Supports Optional Short GI and Green Field modes in TX and RX ■ TX and RX LDPC for improved range and power efficiency ■ Beamforming support ■ All scrambling, encoding, forward error correction, and modulation in the transmit direction and inverse operations in the receive direction. ■ Supports IEEE 802.11h/k for worldwide operation ■ Advanced algorithms for low power, enhanced sensitivity, range, and reliability Document Number: 002-15053 Rev. *D Page 55 of 155 ADVANCE CYW4356 ■ Algorithms to improve performance in presence of Bluetooth ■ Closed loop transmit power control ■ Digital RF chip calibration algorithms to handle CMOS RF chip non-idealities ■ On-the-fly channel frequency and transmit power selection ■ Supports per packet RX antenna diversity ■ Available per-packet channel quality and signal strength measurements ■ Designed to meet FCC and other worldwide regulatory requirements Figure 33. WLAN PHY Block Diagram CCK/DSSS Demodulate Filters and Radio Comp Frequency and Timing Synch OFDM Demodulate Radio Control Block Carrier Sense, AGC, and Rx FSM Buffers Viterbi Decoder Descramble and Deframe MAC Interface FFT/IFFT AFE and Radio Tx FSM Common Logic Block Modulation and Coding Frame and Scramble Filters and Radio Comp PA Comp Modulate/ Spread COEX Document Number: 002-15053 Rev. *D Page 56 of 155 ADVANCE CYW4356 12. WLAN Radio Subsystem The CYW4356 includes an integrated dual-band WLAN RF transceiver that has been optimized for use in 2.4 GHz and 5 GHz Wireless LAN systems. It has been designed to provide low-power, low-cost, and robust communications for applications operating in the globally available 2.4 GHz unlicensed ISM or 5 GHz U-NII bands. The transmit and receive sections include all on-chip filtering, mixing, and gain control functions. Sixteen RF control signals are available (eight per core) to drive external RF switches and support optional external power amplifiers and low-noise amplifiers for each band. See the reference board schematics for further details. A block diagram of the radio subsystem (core 0) is shown in Figure 34. Core 1, is identical to Core 0 without the Bluetooth blocks. Note that integrated on-chip baluns (not shown) convert the fully differential transmit and receive paths to single-ended signal pins. Document Number: 002-15053 Rev. *D Page 57 of 155 ADVANCE CYW4356 Figure 34. Radio Functional Block Diagram (Core 0) WL DAC WL PA WL PAD WL PGA WL A‐PA WL A‐PAD WL A‐PGA WL TXLPF WL TX G‐Mixer WL DAC WL TXLPF WL TX A‐Mixer WL RX A‐Mixer Voltage Regulators WLAN BB WL ADC WL A‐LNA11 WL A‐LNA12 WL RXLPF MUX WL ADC SLNA WL G‐LNA12 WL RXLPF WL RX G‐Mixer WL ATX CLB WL ARX WL GTX WL GRX WL LOGEN WL PLL Gm BT LNA GM Shared XO BT RX BT TX BT LOGEN BT PLL LPO/Ext LPO/RCAL BT ADC BT RXLPF BT ADC BT LNA Load BT RX Mixer BT RXLPF BT BB BT PA BT FM BT DAC BT DAC BT TX Mixer Document Number: 002-15053 Rev. *D BT TXLPF Page 58 of 155 ADVANCE CYW4356 12.1 Receiver Path The CYW4356 has a wide dynamic range, direct conversion receiver that employs high order on-chip channel filtering to ensure reliable operation in the noisy 2.4 GHz ISM band or the entire 5 GHz U-NII band. An on-chip low noise amplifier (LNA) in the 2.4 GHz path in core 0 is shared between the Bluetooth and WLAN receivers, whereas the 5 GHz receive path and the core 1 2.4 GHz receive path have dedicated on-chip LNAs. Control signals are available that can support the use of external LNAs for each band, which can increase the receive sensitivity by several dB. 12.2 Transmit Path Baseband data is modulated and upconverted to the 2.4 GHz ISM or 5 GHz U-NII bands, respectively. Linear on-chip power amplifiers are included, which are capable of delivering high output power while meeting IEEE 802.11ac and IEEE 802.11a/b/g/n specifications, and without the need for external PAs. When using the internal PAs, closed-loop output power control is completely integrated. 12.3 Calibration The CYW4356 features dynamic and automatic on-chip calibration to continually compensate for temperature and process variations across components. These calibration routines are performed periodically in the course of normal radio operation. Examples of some of the automatic calibration algorithms are baseband filter calibration for optimum transmit and receive performance, and LOFT calibration for carrier leakage reduction. In addition, I/Q Calibration, R Calibration, and VCO Calibration are performed on-chip. No per-board calibration is required in manufacturing test, which helps to minimize the test time and cost in large volume production. Document Number: 002-15053 Rev. *D Page 59 of 155 ADVANCE CYW4356 13. Pin Information 13.1 Ball Maps Figure 35 shows the WLBGA ball map. Figure 35. CYW4356 A2 WLBGA BALL MAP; 12 × 18 Array; 192 Balls; Bottom View (Balls Facing Up) 12 11 10 9 8 7 6 5 4 3 2 A SR_PVSS SR_VLX WL_REG_ON SDIO_CMD SDIO_CLK BT_GPIO_5 BT_GPIO_2 PCIE_REFCLKN PCIE_REFCLKP PCIE_TDN PCIE_TDP B SR_VDDBATP5V SR_VDDBATA5V PMU_AVSS SDIO_DATA_0 SDIO_DATA_2 VDDC NC PCIE_PLL_AVSS PCIE_RXTX_AVSS PCIE_PLL_AVDD1P2 PCIE_RXTX_AVDD1 P2 PCIE_RDN B C LDO_VDD1P5 VOUT_CLDO VSSC SDIO_DATA_1 SDIO_DATA_3 NC NC PCIE_PME_L PCIE_PERST_L PCIE_TESTP PCIE_TESTN PCIE_RDP C D VOUT_BTLDO2P5 VOUT_LNLDO BT_REG_ON JTAG_SEL BT_GPIO_3 VSSC PCIE_CLKREQ_L VDDC VSSC E LDO_VDDBAT5V VOUT_LDO3P3_B VDDIO VDDC VDDIO_SD GPIO_7 GPIO_9 BT_USB_DN BT_VDDC F VOUT_3P3 GPIO_2 GPIO_1 GPIO_5 GPIO_6 GPIO_8 LPO_IN BT_USB_DP CLK_REQ G VSSC GPIO_0 VDDC GPIO_3 VSSC AVSS_BBPLL BT_I2S_DO BT_I2S_DI H GPIO_10 VDDIO_RF GPIO_4 J VDDC RF_SW_CTRL_9 RF_SW_CTRL_12 K RF_SW_CTRL_8 M RF_SW_CTRL_10 N WRF_XTAL_OUT P WRF_XTAL_IN VDDC RF_SW_CTRL_11 RF_SW_CTRL_14 WRF_XTAL_GND1P2 WRF_XTAL_VDD1P2 WRF_XTAL_VDD1P5 A D FM_AUDIOVDD1P2 FM_AOUT1 E FM_PLLVDD1P2 FM_AUDIOVSS FM_AOUT2 F VSSC FM_PLLVSS FM_VCOVSS FM_LNAVCOVDD1P 2 G BT_UART_RXD BT_PCM_OUT BT_VDDC FM_LNAVSS FM_RFIN H BT_I2S_CLK BT_UART_TXD BT_PCM_IN BT_HOST_WAKE BT_VCOVSS BT_VCOVDD1P2 J BT_VDDO BT_PCM_SYNC BT_UART_RTS_N BT_GPIO_4 BT_IFVDD1P2 BT_PLLVDD1P2 BT_LNAVDD1P2 K RF_SW_CTRL_15 VSSC BT_I2S_WS BT_UART_CTS_N BT_DEV_WAKE BT_PLLVSS BT_PAVSS BT_RF L RF_SW_CTRL_7 VDDC BT_PCM_CLK BT_VDDC VSSC BT_IFVSS BT_PAVDD2P5 M RF_SW_CTRL_1 RF_SW_CTRL_3 RF_SW_CTRL_4 RF_SW_CTRL_5 RF_SW_CTRL_6 AVDD_BBPLL VDDC RF_SW_CTRL_13 VSSC L 1 RF_SW_CTRL_2 WRF_AFE_GND1P2_ WRF_TX_GND1P2_ CORE0 CORE0 WRF_PA2G_VBAT_ WRF_RFOUT_2G_C GND3P3_CORE0 ORE0 N P R WRF_BUCK_GND1P WRF_BUCK_VDD1P 5_CORE1 5_CORE1 WRF_LOGEN_GND1 WRF_LOGENG_GND WRF_GPIO_OUT_C WRF_PADRV_VBAT WRF_PA2G_VBAT_ P2 1P2 ORE0 _VDD3P3_CORE0 GND3P3_CORE0 WRF_PA2G_VBAT_ VDD3P3_CORE0 R T WRF_RX5G_GND1P WRF_TSSI_A_CORE WRF_PADRV_VBAT WRF_PADRV_VBAT WRF_TX_GND1P2_ WRF_RX2G_GND1P WRF_PADRV_VBAT WRF_PA5G_VBAT_ WRF_MMD_GND1P2 WRF_MMD_VDD1P2 WRF_PFD_VDD1P2 2_CORE1 1 _GND3P3_CORE1 _VDD3P3_CORE1 CORE1 2_CORE1 _GND3P3_CORE0 GND3P3_CORE0 WRF_PA5G_VBAT_ VDD3P3_CORE0 T U WRF_LNA_5G_GND WRF_PA5G_VBAT_ 1P2_CORE1 GND3P3_CORE1 WRF_PA2G_VBAT_ WRF_LNA_2G_GND WRF_BUCK_VDD1P WRF_TSSI_A_CORE WRF_PA5G_VBAT_ WRF_RFOUT_5G_C WRF_VCO_GND1P2 WRF_PFD_GND1P2 GND3P3_CORE1 1P2_CORE1 5_CORE0 0 GND3P3_CORE0 ORE0 U V WRF_RFIN_5G_COR WRF_RFOUT_5G_C WRF_PA5G_VBAT_ E1 ORE1 VDD3P3_CORE1 12 11 WRF_GPIO_OUT_C WRF_AFE_GND1P2_ ORE1 CORE1 WRF_RX2G_GND1P WRF_LNA_2G_GND WRF_RFIN_2G_COR 2_CORE0 1P2_CORE0 E0 WRF_PA5G_VBAT_ GND3P3_CORE1 WRF_PA2G_VBAT_ GND3P3_CORE1 RF_SW_CTRL_0 WRF_PA2G_VBAT_ WRF_RFOUT_2G_C WRF_RFIN_2G_COR WRF_SYNTH_VBAT VDD3P3_CORE1 ORE1 E1 _VDD3P3 10 Document Number: 002-15053 Rev. *D 9 8 7 6 WRF_CP_GND1P2 5 WRF_BUCK_GND1P WRF_RX5G_GND1P WRF_LNA_5G_GND WRF_RFIN_5G_COR 5_CORE0 2_CORE0 1P2_CORE0 E0 4 3 2 V 1 Page 60 of 155 ADVANCE CYW4356 13.2 Pin Lists Table 19. Pin List by Pin Number (192-Pin WLBGA Package) WLBGA Ball# Pin Name A10 WL_REG_ON A11 SR_VLX A12 SR_PVSS A2 PCIE_TDP0 A3 PCIE_TDN0 A4 PCIE_REFCLKP A5 PCIE_REFCLKN A6 BT_GPIO_2 A7 BT_GPIO_5 A8 SDIO_CLK A9 SDIO_CMD B1 PCIE_RDN0 B10 PMU_AVSS B11 SR_VDDBATA5V B12 SR_VDDBATP5V B2 PCIE_RXTX_AVDD1P2 B3 PCIE_PLL_AVDD1P2 B4 PCIE_RXTX_AVSS B5 PCIE_PLL_AVSS B6 NC B7 VDD/VDDC B8 SDIO_DATA_2 B9 SDIO_DATA_0 C1 PCIE_RDP0 C10 VSSC/VSS C11 VOUT_CLDO C12 LDO_VDD1P5 C2 PCIE_TESTN C3 PCIE_TESTP C4 PCIE_PERST_L C5 PCIE_PME_L C6 NC C7 NC C8 SDIO_DATA_3 C9 SDIO_DATA_1 D10 BT_REG_ON D11 VOUT_LNLDO D12 VOUT_BTLDO2P5 D3 VSSC/VSS D4 VDD/VDDC D5 PCIE_CLKREQ_L Document Number: 002-15053 Rev. *D Table 19. Pin List by Pin Number (192-Pin WLBGA Package) WLBGA Ball# Pin Name D6 VSSC/VSS D7 BT_GPIO_3 D9 JTAG_SEL E1 FM_AOUT1 E10 VDDIO E11 VOUT_LDO3P3_B E12 LDO_VDDBAT5V E2 FM_AUDIOVDD1P2 E4 BT_VDDC E5 BT_USB_DN E6 GPIO_9 E7 GPIO_7 E8 VDDIO_SD E9 VDD/VDDC F1 FM_AOUT2 F10 GPIO_1 F11 GPIO_2 F12 VOUT_3P3 F2 FM_AUDIOVSS F3 FM_PLLVDD1P2 F4 CLK_REQ F5 BT_USB_DP F6 LPO_IN F7 GPIO_8 F8 GPIO_6 F9 GPIO_5 G1 FM_LNAVCOVDD1P2 G10 VDD/VDDC G11 GPIO_0 G12 VSSC/VSS G2 FM_VCOVSS G3 FM_PLLVSS G4 VSSC/VSS G5 BT_I2S_DI G6 BT_I2S_DO G7 AVSS_BBPLL G8 VSSC/VSS G9 GPIO_3 H1 FM_RFIN H11 VDDIO_RF H12 GPIO_10 Page 61 of 155 ADVANCE Table 19. Pin List by Pin Number (192-Pin WLBGA Package) WLBGA Ball# Pin Name CYW4356 Table 19. Pin List by Pin Number (192-Pin WLBGA Package) WLBGA Ball# Pin Name H2 FM_LNAVSS M6 BT_PCM_CLK H3 BT_VDDC M7 VDD/VDDC H4 BT_PCM_OUT M8 RF_SW_CTRL_7 H5 BT_UART_RXD N1 WRF_RFIN_2G_CORE0 H7 AVDD_BBPLL N10 WRF_XTAL_VDD1P2 H9 GPIO_4 N11 WRF_XTAL_GND1P2 J1 BT_VCOVDD1P2 N12 WRF_XTAL_OUT J11 RF_SW_CTRL_9 N2 WRF_LNA_2G_GND1P2_CORE0 J12 VDD/VDDC N3 WRF_RX2G_GND1P2_CORE0 J2 BT_VCOVSS N5 RF_SW_CTRL_4 J3 BT_HOST_WAKE N7 RF_SW_CTRL_3 J4 BT_PCM_IN N8 RF_SW_CTRL_1 J5 BT_UART_TXD P1 WRF_RFOUT_2G_CORE0 J6 BT_I2S_CLK P11 WRF_XTAL_VDD1P5 J8 VDD/VDDC P12 WRF_XTAL_IN J9 RF_SW_CTRL_12 P2 WRF_PA2G_VBAT_GND3P3_CORE0 K1 BT_LNAVDD1P2 P3 WRF_TX_GND1P2_CORE0 K10 RF_SW_CTRL_13 P4 WRF_AFE_GND1P2_CORE0 K12 RF_SW_CTRL_8 P5 RF_SW_CTRL_6 K2 BT_PLLVDD1P2 P7 RF_SW_CTRL_5 K3 BT_IFVDD1P2 P9 RF_SW_CTRL_2 K4 BT_GPIO_4 R1 WRF_PA2G_VBAT_VDD3P3_CORE0 K5 BT_UART_RTS_L R11 WRF_BUCK_VDD1P5_CORE1 K6 BT_PCM_SYNC R12 WRF_BUCK_GND1P5_CORE1 K7 BT_VDDIO R2 WRF_PA2G_VBAT_GND3P3_CORE0 L1 BT_RF R3 WRF_PADRV_VBAT_VDD3P3_CORE0 L10 VDD/VDDC R4 WRF_GPIO_OUT_CORE0 L11 VSSC/VSS R5 WRF_LOGENG_GND1P2 L2 BT_PAVSS R6 WRF_LOGEN_GND1P2 L3 BT_PLLVSS R7 RF_SW_CTRL_0 L4 BT_DEV_WAKE R8 WRF_AFE_GND1P2_CORE1 L5 BT_UART_CTS_L R9 WRF_GPIO_OUT_CORE1 L6 BT_I2S_WS T1 WRF_PA5G_VBAT_VDD3P3_CORE0 L7 VSSC/VSS T10 WRF_PADRV_VBAT_GND3P3_CORE1 L8 RF_SW_CTRL_15 T11 WRF_TSSI_A_CORE1 L9 RF_SW_CTRL_11 T12 WRF_RX5G_GND1P2_CORE1 M1 BT_PAVDD2P5 T2 WRF_PA5G_VBAT_GND3P3_CORE0 M10 RF_SW_CTRL_14 T3 WRF_PADRV_VBAT_GND3P3_CORE0 M12 RF_SW_CTRL_10 T4 WRF_PFD_VDD1P2 M3 BT_IFVSS T5 WRF_MMD_VDD1P2 M4 VSSC/VSS T6 WRF_MMD_GND1P2 M5 BT_VDDC T7 WRF_RX2G_GND1P2_CORE1 Document Number: 002-15053 Rev. *D Page 62 of 155 ADVANCE CYW4356 Table 19. Pin List by Pin Number (192-Pin WLBGA Package) WLBGA Ball# Pin Name T8 WRF_TX_GND1P2_CORE1 T9 WRF_PADRV_VBAT_VDD3P3_CORE1 U1 WRF_RFOUT_5G_CORE0 U10 WRF_PA5G_VBAT_GND3P3_CORE1 U11 WRF_PA5G_VBAT_GND3P3_CORE1 U12 WRF_LNA_5G_GND1P2_CORE1 U2 WRF_PA5G_VBAT_GND3P3_CORE0 U3 WRF_TSSI_A_CORE0 U4 WRF_BUCK_VDD1P5_CORE0 U5 WRF_PFD_GND1P2 U6 WRF_VCO_GND1P2 U7 WRF_LNA_2G_GND1P2_CORE1 U8 WRF_PA2G_VBAT_GND3P3_CORE1 U9 WRF_PA2G_VBAT_GND3P3_CORE1 V1 WRF_RFIN_5G_CORE0 V10 WRF_PA5G_VBAT_VDD3P3_CORE1 V11 WRF_RFOUT_5G_CORE1 V12 WRF_RFIN_5G_CORE1 V2 WRF_LNA_5G_GND1P2_CORE0 V3 WRF_RX5G_GND1P2_CORE0 V4 WRF_BUCK_GND1P5_CORE0 V5 WRF_CP_GND1P2 V6 WRF_SYNTH_VBAT_VDD3P3 V7 WRF_RFIN_2G_CORE1 V8 WRF_RFOUT_2G_CORE1 V9 WRF_PA2G_VBAT_VDD3P3_CORE1 Document Number: 002-15053 Rev. *D Page 63 of 155 ADVANCE Table 20. Pin List by Pin Name (192-Pin WLBGA Package) Pin Name CYW4356 Table 20. Pin List by Pin Name (192-Pin WLBGA Package) WLBGA Ball# Pin Name WLBGA Ball# AVDD_BBPLL H7 FM_AUDIOVSS F2 AVSS_BBPLL G7 FM_LNAVCOVDD1P2 G1 BT_DEV_WAKE L4 FM_LNAVSS H2 BT_GPIO_2 A6 FM_PLLVDD1P2 F3 BT_GPIO_5 A7 FM_PLLVSS G3 BT_GPIO_3 D7 FM_RFIN H1 BT_GPIO_4 K4 FM_VCOVSS G2 BT_HOST_WAKE J3 GPIO_0 G11 BT_I2S_CLK J6 GPIO_1 F10 BT_I2S_DI G5 GPIO_10 H12 BT_I2S_DO G6 GPIO_2 F11 BT_I2S_WS L6 GPIO_3 G9 BT_IFVDD1P2 K3 GPIO_4 H9 BT_IFVSS M3 GPIO_5 F9 BT_LNAVDD1P2 K1 GPIO_6 F8 BT_PAVDD2P5 M1 GPIO_7 E7 BT_PAVSS L2 GPIO_8 F7 BT_PCM_CLK M6 GPIO_9 E6 BT_PCM_IN J4 JTAG_SEL D9 BT_PCM_OUT H4 LDO_VDD1P5 C12 BT_PCM_SYNC K6 LDO_VDDBAT5V E12 BT_PLLVDD1P2 K2 LPO_IN F6 BT_PLLVSS L3 NC B6 BT_REG_ON D10 NC C7 BT_RF L1 NC C6 BT_UART_CTS_L L5 PCIE_PME_L C5 BT_UART_RTS_L K5 PCIE_CLKREQ_L D5 BT_UART_RXD H5 PCIE_PERST_L C4 BT_UART_TXD J5 PCIE_PLL_AVDD1P2 B3 BT_USB_DN E5 PCIE_PLL_AVSS B5 BT_USB_DP F5 PCIE_RDN0 B1 BT_VCOVDD1P2 J1 PCIE_RDP0 C1 BT_VCOVSS J2 PCIE_REFCLKN A5 BT_VDDC E4 PCIE_REFCLKP A4 BT_VDDC H3 PCIE_RXTX_AVDD1P2 B2 BT_VDDC M5 PCIE_RXTX_AVSS B4 BT_VDDIO K7 PCIE_TDN0 A3 CLK_REQ F4 PCIE_TDP0 A2 FM_AOUT1 E1 PCIE_TESTN C2 FM_AOUT2 F1 PCIE_TESTP C3 E2 PMU_AVSS B10 FM_AUDIOVDD1P2 Document Number: 002-15053 Rev. *D Page 64 of 155 ADVANCE Table 20. Pin List by Pin Name (192-Pin WLBGA Package) Pin Name CYW4356 Table 20. Pin List by Pin Name (192-Pin WLBGA Package) WLBGA Ball# Pin Name WLBGA Ball# RF_SW_CTRL_0 R7 VSSC/VSS C10 RF_SW_CTRL_1 N8 VSSC/VSS D3 RF_SW_CTRL_10 M12 VSSC/VSS D6 RF_SW_CTRL_11 L9 VSSC/VSS G12 RF_SW_CTRL_12 J9 VSSC/VSS G4 RF_SW_CTRL_13 K10 VSSC/VSS G8 RF_SW_CTRL_14 M10 VSSC/VSS L11 RF_SW_CTRL_15 L8 VSSC/VSS L7 RF_SW_CTRL_2 P9 VSSC/VSS M4 RF_SW_CTRL_3 N7 WL_REG_ON A10 RF_SW_CTRL_4 N5 WRF_AFE_GND1P2_CORE0 P4 RF_SW_CTRL_5 P7 WRF_AFE_GND1P2_CORE1 R8 RF_SW_CTRL_6 P5 WRF_BUCK_GND1P5_CORE0 V4 RF_SW_CTRL_7 M8 WRF_BUCK_GND1P5_CORE1 R12 RF_SW_CTRL_8 K12 WRF_BUCK_VDD1P5_CORE0 U4 RF_SW_CTRL_9 J11 WRF_BUCK_VDD1P5_CORE1 R11 SDIO_CLK A8 WRF_CP_GND1P2 V5 SDIO_CMD A9 WRF_GPIO_OUT_CORE0 R4 SDIO_DATA_0 B9 WRF_GPIO_OUT_CORE1 R9 SDIO_DATA_1 C9 WRF_LNA_2G_GND1P2_CORE0 N2 SDIO_DATA_2 B8 WRF_LNA_2G_GND1P2_CORE1 U7 SDIO_DATA_3 C8 WRF_LNA_5G_GND1P2_CORE0 V2 SR_PVSS A12 WRF_LNA_5G_GND1P2_CORE1 U12 SR_VDDBATA5V B11 WRF_LOGEN_GND1P2 R6 SR_VDDBATP5V B12 WRF_LOGENG_GND1P2 R5 SR_VLX A11 WRF_MMD_GND1P2 T6 VDD/VDDC B7 WRF_MMD_VDD1P2 T5 VDD/VDDC D4 WRF_PA2G_VBAT_GND3P3_CORE0 P2 VDD/VDDC E9 WRF_PA2G_VBAT_GND3P3_CORE0 R2 VDD/VDDC G10 WRF_PA2G_VBAT_GND3P3_CORE1 U8 VDD/VDDC J12 WRF_PA2G_VBAT_GND3P3_CORE1 U9 VDD/VDDC J8 WRF_PA2G_VBAT_VDD3P3_CORE0 R1 VDD/VDDC L10 WRF_PA2G_VBAT_VDD3P3_CORE1 V9 VDD/VDDC M7 WRF_PA5G_VBAT_GND3P3_CORE0 T2 VDDIO E10 WRF_PA5G_VBAT_GND3P3_CORE0 U2 VDDIO_RF H11 WRF_PA5G_VBAT_GND3P3_CORE1 U10 VDDIO_SD E8 WRF_PA5G_VBAT_GND3P3_CORE1 U11 VOUT_3P3 F12 WRF_PA5G_VBAT_VDD3P3_CORE0 T1 VOUT_BTLDO2P5 D12 WRF_PA5G_VBAT_VDD3P3_CORE1 V10 VOUT_CLDO C11 WRF_PADRV_VBAT_GND3P3_CORE0 T3 VOUT_LDO3P3_B E11 WRF_PADRV_VBAT_GND3P3_CORE1 T10 VOUT_LNLDO D11 Document Number: 002-15053 Rev. *D Page 65 of 155 ADVANCE CYW4356 Table 20. Pin List by Pin Name (192-Pin WLBGA Package) Pin Name WLBGA Ball# WRF_PADRV_VBAT_VDD3P3_CORE0 R3 WRF_PADRV_VBAT_VDD3P3_CORE1 T9 WRF_PFD_GND1P2 U5 WRF_PFD_VDD1P2 T4 WRF_RFIN_2G_CORE0 N1 WRF_RFIN_2G_CORE1 V7 WRF_RFIN_5G_CORE0 V1 WRF_RFIN_5G_CORE1 V12 WRF_RFOUT_2G_CORE0 P1 WRF_RFOUT_2G_CORE1 V8 WRF_RFOUT_5G_CORE0 U1 WRF_RFOUT_5G_CORE1 V11 WRF_RX2G_GND1P2_CORE0 N3 WRF_RX2G_GND1P2_CORE1 T7 WRF_RX5G_GND1P2_CORE0 V3 WRF_RX5G_GND1P2_CORE1 T12 WRF_SYNTH_VBAT_VDD3P3 V6 WRF_TSSI_A_CORE0 U3 WRF_TSSI_A_CORE1 T11 WRF_TX_GND1P2_CORE0 P3 WRF_TX_GND1P2_CORE1 T8 WRF_VCO_GND1P2 U6 WRF_XTAL_GND1P2 N11 WRF_XTAL_IN P12 WRF_XTAL_OUT N12 WRF_XTAL_VDD1P2 N10 WRF_XTAL_VDD1P5 P11 Document Number: 002-15053 Rev. *D Page 66 of 155 ADVANCE CYW4356 Table 21. 395-Bump WLCSP Coordinates Coordinates (0,0 center of die) No. Net Name Bump Side X Top Side Y X Y 1 PCIE_RXTX_AVSS 2300.51 3659.87 –2300.51 3659.87 2 PCIE_PLL_AVSS 1966.81 3659.87 –1966.81 3659.87 3 PCIE_REFCLKP 1966.81 3434.87 –1966.81 3434.87 4 PCIE_REFCLKN 1800.31 3547.37 –1800.31 3547.37 5 PCIE_TDN0 2134.01 3547.37 –2134.01 3547.37 6 PCIE_TDP0 2134.01 3322.37 –2134.01 3322.37 7 PCIE_RXTX_AVDD1P2 2134.01 3068.53 –2134.01 3068.53 8 PCIE_RDP0 2300.51 3209.87 –2300.51 3209.87 9 PCIE_RDN0 2300.51 3434.87 –2300.51 3434.87 10 PCIE_PLL_AVSS 1966.81 3209.87 –1966.81 3209.87 11 PCIE_PLL_AVDD1P2 1800.31 3322.37 –1800.31 3322.37 12 NC 508.44 3481.00 –508.44 3481.00 13 NC 768.62 3062.57 –768.62 3062.57 14 NC 508.44 3281.00 –508.44 3281.00 15 NC 1177.22 3062.57 –1177.22 3062.57 16 NC 972.92 3062.57 –972.92 3062.57 17 NC 553.11 3681.00 –553.11 3681.00 18 NC 753.11 3681.00 –753.11 3681.00 19 NC 773.17 3481.00 –773.17 3481.00 20 NC 773.17 3281.00 –773.17 3281.00 21 NC 974.72 3481.00 –974.72 3481.00 22 NC 974.72 3281.00 –974.72 3281.00 23 NC 982.37 3681.00 –982.37 3681.00 24 NC 1176.88 3281.00 –1176.88 3281.00 25 NC 1176.88 3481.00 –1176.88 3481.00 26 NC 1186.67 3681.00 –1186.67 3681.00 27 NC 526.91 3062.57 –526.91 3062.57 28 NC 1177.22 2860.07 –1177.22 2860.07 29 NC 768.62 2860.07 –768.62 2860.07 30 GND 1601.79 3595.19 –1601.79 3595.19 31 NC 1601.79 2792.39 –1601.79 2792.39 32 GND 1401.09 3394.49 –1401.09 3394.49 33 NC 1601.79 3394.49 –1601.79 3394.49 34 GND 1601.79 2993.09 –1601.79 2993.09 35 NC 1601.79 3193.79 –1601.79 3193.79 36 GND 1401.09 2792.39 –1401.09 2792.39 37 GND 1401.09 3595.19 –1401.09 3595.19 38 NC 1401.09 2993.09 –1401.09 2993.09 39 GND 1401.09 3193.79 –1401.09 3193.79 Document Number: 002-15053 Rev. *D Page 67 of 155 ADVANCE CYW4356 Table 21. 395-Bump WLCSP Coordinates (Cont.) Coordinates (0,0 center of die) No. Net Name Bump Side X Top Side Y X Y 40 BT_PAVSS 2217.95 –736.50 –2217.95 –736.50 41 BT_AGPIO 2017.95 –1298.03 –2017.95 –1298.03 42 BT_IFVDD1P2 1768.91 –1298.03 –1768.91 –1298.03 43 BT_IFVSS 1568.92 –1298.03 –1568.92 –1298.03 44 BT_LNAVDD1P2 2228.18 –392.72 –2228.18 –392.72 45 BT_LNAVSS 1843.60 –524.82 –1843.60 –524.82 46 BT_PAVDD2P5 2176.03 –1164.53 –2176.03 –1164.53 47 BT_PLLVDD1P2 1768.91 –223.55 –1768.91 –223.55 48 BT_PLLVSS 1568.92 –223.55 –1568.92 –223.55 49 BT_RF 2252.39 –936.50 –2252.39 –936.50 50 BT_VCOVDD1P2 2227.01 –189.65 –2227.01 –189.65 51 BT_VCOVSS 1967.62 –45.40 –1967.62 –45.40 52 FM_AUDIOVDD1P2 2044.00 931.81 –2044.00 931.81 53 FM_AUDIOAVSS 2044.00 1143.58 –2044.00 1143.58 54 FM_AOUT1 2244.00 1143.58 –2244.00 1143.58 55 FM_AOUT2 2244.00 931.81 –2244.00 931.81 56 FM_IFVDD1P2 1614.95 371.79 –1614.95 371.79 57 FM_IFVSS 1614.95 171.80 –1614.95 171.80 58 FM_PLLVSS 1793.21 871.61 –1793.21 871.61 59 FM_PLLVDD1P2 1686.40 695.87 –1686.40 695.87 60 FM_RFAUX 2273.40 68.08 –2273.40 68.08 61 FM_RFIN 2260.02 313.69 –2260.02 313.69 62 FM_LNAVDD1P2 2060.02 354.59 –2060.02 354.59 63 FM_LNAVSS 2060.02 154.59 –2060.02 154.59 64 FM_VCOVDD1P2 2273.40 731.81 –2273.40 731.81 65 FM_VCOVSS 2273.40 531.81 –2273.40 531.81 66 RF_SW_CTRL_0 –2202.33 –1494.00 2202.33 –1494.00 67 VDDC –661.10 –1355.99 661.10 –1355.99 68 VSSC 740.99 2052.00 –740.99 2052.00 69 VSSC –616.50 –408.01 616.50 –408.01 70 VSSC –459.00 –198.00 459.00 –198.00 71 VSSC –546.71 –1008.00 546.71 –1008.00 72 VSSC –546.71 –708.00 546.71 –708.00 73 VSSC –459.00 252.00 459.00 252.00 74 VDDC –661.10 –21.01 661.10 –21.01 75 VSSC 740.99 2352.00 –740.99 2352.00 76 VDDIO_SD –405.00 2299.50 405.00 2299.50 77 SDIO_DATA_1 –337.05 2531.57 337.05 2531.57 78 SDIO_CLK –337.05 2731.57 337.05 2731.57 79 SDIO_DATA_3 –337.05 2931.58 337.05 2931.58 Document Number: 002-15053 Rev. *D Page 68 of 155 ADVANCE CYW4356 Table 21. 395-Bump WLCSP Coordinates (Cont.) Coordinates (0,0 center of die) No. Net Name Bump Side Top Side X Y X Y 80 SDIO_DATA_2 –337.05 3131.59 337.05 3131.59 81 SDIO_CMD –337.05 3331.59 337.05 3331.59 82 SDIO_DATA_0 –337.05 3531.60 337.05 3531.60 83 VSSC –316.50 –408.01 316.50 –408.01 84 VSSC –266.51 –1008.00 266.51 –1008.00 85 VSSC –266.51 –708.00 266.51 –708.00 86 RF_SW_CTRL_4 –2072.12 –1125.00 2072.12 –1125.00 87 VDDC –261.11 –21.01 261.11 –21.01 88 VSSC –259.00 1651.99 259.00 1651.99 89 VSSC –159.00 252.00 159.00 252.00 90 VSSC –159.00 552.00 159.00 552.00 91 VSSC –159.00 851.99 159.00 851.99 92 VSSC –159.00 1151.99 159.00 1151.99 93 VSSC –159.00 1451.99 159.00 1451.99 94 VSSC –159.00 2052.00 159.00 2052.00 95 VSSC –459.00 552.00 459.00 552.00 96 GND –67.05 2286.36 67.05 2286.36 97 GND –67.05 2486.57 67.05 2486.57 98 VDDC_98 –67.05 2686.57 67.05 2686.57 99 NC –67.05 2886.58 67.05 2886.58 100 NC –67.05 3086.59 67.05 3086.59 101 NC –67.05 3286.59 67.05 3286.59 102 VDDC_102 –67.05 3486.60 67.05 3486.60 103 VDDC –61.11 –1220.99 61.11 –1220.99 104 VSSC –61.11 –1008.00 61.11 –1008.00 105 VSSC –61.11 –708.00 61.11 –708.00 106 VSSC –61.11 –408.01 61.11 –408.01 107 VDDC –61.11 –21.01 61.11 –21.01 108 VDDC –61.11 1843.97 61.11 1843.97 109 VDDC 138.89 –1220.99 –138.89 –1220.99 110 VDDC 138.89 –1021.00 –138.89 –1021.00 111 VDDC 138.89 –821.00 –138.89 –821.00 112 VDDC –261.11 –1220.99 261.11 –1220.99 113 VDDC 138.89 –421.00 –138.89 –421.00 114 VDDC 138.89 –221.00 –138.89 –221.00 115 VDDC 138.89 –21.01 –138.89 –21.01 116 VSSC 140.99 252.00 –140.99 252.00 117 VSSC 140.99 552.00 –140.99 552.00 118 VSSC 140.99 851.99 –140.99 851.99 119 VSSC 140.99 1151.99 –140.99 1151.99 Document Number: 002-15053 Rev. *D Page 69 of 155 ADVANCE CYW4356 Table 21. 395-Bump WLCSP Coordinates (Cont.) Coordinates (0,0 center of die) No. Net Name Bump Side X Top Side Y X Y 120 VSSC 140.99 1451.99 –140.99 1451.99 121 VSSC 140.99 1651.99 –140.99 1651.99 122 VSSC 140.99 2052.00 –140.99 2052.00 123 PACKAGEOPTION_4 140.99 2352.00 –140.99 2352.00 124 BT_VSSC 768.37 –1186.86 –768.37 –1186.86 125 BT_VSSC 816.40 21.84 –816.40 21.84 126 BT_VSSC 599.69 –715.49 –599.69 –715.49 127 VDDC 338.89 443.99 –338.89 443.99 128 VDDC 338.89 643.99 –338.89 643.99 129 VDDC 338.89 1843.97 –338.89 1843.97 130 VSSC –459.00 851.99 459.00 851.99 131 PACKAGEOPTION_2 440.99 2352.00 –440.99 2352.00 132 PACKAGEOPTION_3 440.99 2592.00 –440.99 2592.00 133 BT_VSSC 468.37 –1186.86 –468.37 –1186.86 134 VDDC 538.88 643.99 –538.88 643.99 135 VDDC 538.88 843.98 –538.88 843.98 136 VDDC 538.88 1043.98 –538.88 1043.98 137 VDDC 538.88 1243.98 –538.88 1243.98 138 VDDC 538.88 1443.98 –538.88 1443.98 139 VDDC 538.88 1643.98 –538.88 1643.98 140 VDDC 538.88 1843.97 –538.88 1843.97 141 BT_VDDC_ISO_1 601.19 –970.04 –601.19 –970.04 142 BT_VDDC_ISO_2 620.91 –500.07 –620.91 –500.07 143 AVDD_BBPLL 655.50 168.14 –655.50 168.14 144 AVSS_BBPLL 655.50 437.48 –655.50 437.48 145 BT_VDDC 1480.37 555.67 –1480.37 555.67 146 PACKAGEOPTION_1 740.99 2592.00 –740.99 2592.00 147 BT_VDDC 1480.37 780.66 –1480.37 780.66 148 BT_VDDIO 830.29 –445.06 –830.29 –445.06 149 BT_VDDIO 840.29 –724.53 –840.29 –724.53 150 BT_VDDIO 865.28 –245.06 –865.28 –245.06 151 BT_VDDIO 915.28 –973.39 –915.28 –973.39 152 PACKAGEOPTION_0 1040.99 2592.00 –1040.99 2592.00 153 BT_GPIO_5 1048.37 420.67 –1048.37 420.67 154 BT_GPIO_3 1048.37 620.67 –1048.37 620.67 155 BT_GPIO_2 1048.37 820.67 –1048.37 820.67 156 BT_I2S_DI 1444.06 1426.01 –1444.06 1426.01 157 BT_UART_TXD 1444.06 1643.00 –1444.06 1643.00 158 BT_I2S_WS 1143.51 1940.00 –1143.51 1940.00 159 LPO_IN 1143.51 2237.00 –1143.51 2237.00 Document Number: 002-15053 Rev. *D Page 70 of 155 ADVANCE CYW4356 Table 21. 395-Bump WLCSP Coordinates (Cont.) Coordinates (0,0 center of die) No. Net Name Bump Side Top Side X Y X Y 160 OTP_VDD33 1348.51 2444.00 –1348.51 2444.00 161 BT_CLK_REQ 1644.06 1426.01 –1644.06 1426.01 162 BT_UART_RXD 1644.06 1643.00 –1644.06 1643.00 163 BT_PCM_SYNC 1343.51 1940.00 –1343.51 1940.00 164 BT_USB_DN 1343.51 2237.00 –1343.51 2237.00 165 PCIE_PME_L 1548.50 2444.00 –1548.50 2444.00 166 BT_TM1 1844.06 1346.00 –1844.06 1346.00 167 BT_I2S_CLK 1844.06 1643.00 –1844.06 1643.00 168 BT_GPIO_4 1543.51 1940.00 –1543.51 1940.00 169 BT_USB_DP 1543.51 2237.00 –1543.51 2237.00 170 BT_HOST_WAKE 2044.05 1346.00 –2044.05 1346.00 171 BT_I2S_DO 2044.05 1643.00 –2044.05 1643.00 172 BT_UART_CTS_N 1743.51 1940.00 –1743.51 1940.00 173 BT_PCM_IN 1743.51 2237.00 –1743.51 2237.00 174 PCIE_CLKREQ_L 1858.50 2534.00 –1858.50 2534.00 175 RF_SW_CTRL_1 –2002.32 –1494.00 2002.32 –1494.00 176 BT_DEV_WAKE 2244.05 1346.00 –2244.05 1346.00 177 BT_PCM_OUT 2244.05 1643.00 –2244.05 1643.00 178 BT_UART_RTS_N 1943.51 1940.00 –1943.51 1940.00 179 BT_PCM_CLK 1943.51 2237.00 –1943.51 2237.00 180 PERST_L 2058.50 2534.00 –2058.50 2534.00 181 RF_SW_CTRL_8 –1945.91 –806.00 1945.91 –806.00 182 GPIO_13 –2040.71 516.01 2040.71 516.01 183 RF_SW_CTRL_5 –1872.11 –1125.00 1872.11 –1125.00 184 RF_SW_CTRL_12 –1760.12 –327.01 1760.12 –327.01 185 GPIO_10 –1959.30 229.01 1959.30 229.01 186 RF_SW_CTRL_2 –1802.31 –1494.00 1802.31 –1494.00 187 RF_SW_CTRL_9 –1745.90 –806.00 1745.90 –806.00 188 GPIO_14 –1840.71 516.01 1840.71 516.01 189 GPIO_7 –1853.50 –18.00 1853.50 –18.00 190 RF_SW_CTRL_6 –1672.10 –1125.00 1672.10 –1125.00 191 RF_SW_CTRL_13 –1560.11 –327.01 1560.11 –327.01 192 GPIO_11 –1759.91 279.00 1759.91 279.00 193 RF_SW_CTRL_3 –1602.31 –1494.00 1602.31 –1494.00 194 RF_SW_CTRL_10 –1545.89 –806.00 1545.89 –806.00 195 GPIO_15 –1640.70 516.01 1640.70 516.01 196 GPIO_8 –1593.91 22.00 1593.91 22.00 197 RF_SW_CTRL_7 –1472.09 –1125.00 1472.09 –1125.00 198 RF_SW_CTRL_14 –1360.11 –327.01 1360.11 –327.01 199 GPIO_12 –1559.91 279.00 1559.91 279.00 Document Number: 002-15053 Rev. *D Page 71 of 155 ADVANCE CYW4356 Table 21. 395-Bump WLCSP Coordinates (Cont.) Coordinates (0,0 center of die) No. Net Name Bump Side Top Side X Y X Y 200 VSSC –459.00 1151.99 459.00 1151.99 201 VSSC –459.00 1451.99 459.00 1451.99 202 RF_SW_CTRL_11 –1346.09 –756.00 1346.09 –756.00 203 VDDC –459.00 1651.99 459.00 1651.99 204 VDDC –1345.37 1017.54 1345.37 1017.54 205 GPIO_9 –1393.90 22.00 1393.90 22.00 206 VDDIO –1215.90 576.00 1215.90 576.00 207 RF_SW_CTRL_15 –1160.10 –327.01 1160.10 –327.01 208 VDDC –1261.10 1843.97 1261.10 1843.97 209 VDDC –1061.11 –1156.00 1061.11 –1156.00 210 VDDC –1061.11 –776.00 1061.11 –776.00 211 VDDC –1061.10 –1355.99 1061.10 –1355.99 212 VDDC_ISO_PHY –1402.10 –1494.00 1402.10 –1494.00 213 VDDC –1180.10 –587.00 1180.10 –587.00 214 VDDC_ISO_PHY –1151.11 –956.00 1151.11 –956.00 215 VDDC_ISO_DIG –1058.99 2052.00 1058.99 2052.00 216 VDDC_ISO_DIG –816.10 1843.97 816.10 1843.97 217 VSSC –459.00 2052.00 459.00 2052.00 218 GPIO_0 –996.05 2877.58 996.05 2877.58 219 GPIO_1 –996.05 3077.59 996.05 3077.59 220 GPIO_2 –996.05 3277.59 996.05 3277.59 221 GPIO_3 –996.05 3477.60 996.05 3477.60 222 VDDIO –990.90 576.00 990.90 576.00 223 VDDIO_RF –960.10 –117.00 960.10 –117.00 224 VDDC –1061.10 1843.97 1061.10 1843.97 225 VDDC_ISO_PHY –1061.10 843.98 1061.10 843.98 226 VDDC_ISO_PHY –1058.99 1151.99 1058.99 1151.99 227 VDDIO_RF –852.10 –387.00 852.10 –387.00 228 VDDC –461.11 –1355.99 461.11 –1355.99 229 GPIO_4 –769.05 3196.59 769.05 3196.59 230 VDDIO_PCIE –759.00 252.00 759.00 252.00 231 VDDIO –759.00 552.00 759.00 552.00 232 VSSC –1359.90 279.00 1359.90 279.00 233 VSSC –1319.39 2052.00 1319.39 2052.00 234 VSSC –1358.99 2302.00 1358.99 2302.00 235 VSSC –1351.11 –956.00 1351.11 –956.00 236 GPIO_6 –751.05 2996.59 751.05 2996.59 237 GPIO_5 –751.05 3396.60 751.05 3396.60 238 VDDIO_SD –745.50 2352.00 745.50 2352.00 239 JTAG_SEL –733.05 2796.58 733.05 2796.58 Document Number: 002-15053 Rev. *D Page 72 of 155 ADVANCE CYW4356 Table 21. 395-Bump WLCSP Coordinates (Cont.) Coordinates (0,0 center of die) No. Net Name Bump Side Top Side X Y X Y 240 VDDC_ISO_PHY –729.00 –220.50 729.00 –220.50 241 VDDC –951.31 –956.00 951.31 –956.00 242 VDDC –861.10 –1355.99 861.10 –1355.99 243 VSSC –1440.90 576.00 1440.90 576.00 244 VSSC –1159.90 –98.00 1159.90 –98.00 245 VSSC –1159.90 279.00 1159.90 279.00 246 VDDC –616.10 1843.97 616.10 1843.97 247 WRF_SYNTH_VBAT_VDD3P3 75.91 –3598.00 –75.91 –3598.00 248 WRF_XTAL_GND1P2 –2003.12 –1834.98 2003.12 –1834.98 249 WRF_XTAL_VDD1P5 –2003.12 –2065.65 2003.12 –2065.65 250 WRF_VCO_GND1P2 198.52 –3109.71 –198.52 –3109.71 251 WRF_XTAL_IN –2205.82 –2065.65 2205.82 –2065.65 252 WRF_LOGEN_GND1P2 126.11 –2303.63 –126.11 –2303.63 253 WRF_XTAL_OUT –2205.82 –1818.42 2205.82 –1818.42 254 WRF_XTAL_VDD1P2 –1807.98 –1960.54 1807.98 –1960.54 255 WRF_TX_GND1P2_CORE1 –437.83 –2417.93 437.83 –2417.93 256 WRF_BUCK_GND1P5_CORE1 –2137.36 –2823.85 2137.36 –2823.85 257 WRF_RX5G_GND1P2_CORE1 –1968.14 –2944.01 1968.14 –2944.01 258 WRF_GPIO_OUT_CORE1 –877.08 –2398.01 877.08 –2398.01 259 WRF_RX2G_GND1P2_CORE1 –167.27 –2716.52 167.27 –2716.52 260 WRF_RFIN_5G_CORE1 –2253.44 –3538.14 2253.44 –3538.14 261 WRF_RFIN_2G_CORE1 –201.47 –3598.00 201.47 –3598.00 262 WRF_PFD_VDD1P2 901.40 –2994.96 –901.40 –2994.96 263 WRF_PFD_GND1P2 818.12 –3198.01 –818.12 –3198.01 264 WRF_PADRV_VBAT_VDD3P3_CORE1 –1090.70 –2792.61 1090.70 –2792.61 265 WRF_PADRV_VBAT_GND3P3_CORE1 –1401.46 –2798.01 1401.46 –2798.01 266 WRF_PA5G_VBAT_VDD3P3_CORE1 –1401.46 –3679.00 1401.46 –3679.00 267 WRF_AFE_GND1P2_CORE1 –631.56 –2293.35 631.56 –2293.35 268 WRF_PA5G_VBAT_GND3P3_CORE0 1825.51 –2798.01 –1825.51 –2798.01 269 WRF_PA5G_VBAT_VDD3P3_CORE0 2297.50 –2998.01 –2297.50 –2998.01 270 WRF_MMD_VDD1P2 692.41 –2994.96 –692.41 –2994.96 271 WRF_MMD_GND1P2 499.12 –2798.01 –499.12 –2798.01 272 WRF_PA2G_VBAT_GND3P3_CORE0 1744.51 –1940.22 –1744.51 –1940.22 273 WRF_LNA_5G_GND1P2_CORE0 1877.39 –3673.49 –1877.39 –3673.49 274 WRF_CP_GND1P2 539.26 –3598.00 –539.26 –3598.00 275 WRF_LNA_2G_GND1P2_CORE0 1798.51 –1598.02 –1798.51 –1598.02 276 WRF_TSSI_A_CORE1 –1839.15 –2716.77 1839.15 –2716.77 277 WRF_BUCK_VDD1P5_CORE0 1024.35 –3433.91 –1024.35 –3433.91 278 WRF_LOGENG_GND1P2 770.31 –2353.01 –770.31 –2353.01 279 WRF_RFOUT_2G_CORE1 –601.47 –3679.00 601.47 –3679.00 Document Number: 002-15053 Rev. *D Page 73 of 155 ADVANCE CYW4356 Table 21. 395-Bump WLCSP Coordinates (Cont.) Coordinates (0,0 center of die) No. Net Name Bump Side X Top Side Y X Y 280 WRF_RFOUT_5G_CORE0 2288.50 –3198.01 –2288.50 –3198.01 281 WRF_AFE_GND1P2_CORE0 880.13 –2028.11 –880.13 –2028.11 282 WRF_LNA_2G_GND1P2_CORE1 –201.47 –3198.01 201.47 –3198.01 283 WRF_LNA_5G_GND1P2_CORE1 –2276.94 –3276.89 2276.94 –3276.89 284 WRF_PA2G_VBAT_GND3P3_CORE1 –543.68 –3144.01 543.68 –3144.01 285 WRF_PA2G_VBAT_VDD3P3_CORE1 –801.47 –3697.00 801.47 –3697.00 286 WRF_PA5G_VBAT_GND3P3_CORE1 –1801.46 –3225.01 1801.46 –3225.01 287 WRF_PA5G_VBAT_VDD3P3_CORE0 2279.50 –2798.01 –2279.50 –2798.01 288 WRF_PADRV_VBAT_GND3P3_CORE0 1398.51 –2798.01 –1398.51 –2798.01 289 WRF_PADRV_VBAT_VDD3P3_CORE0 1393.11 –2487.25 –1393.11 –2487.25 290 WRF_RFIN_2G_CORE0 2198.50 –1598.02 –2198.50 –1598.02 291 WRF_RX2G_GND1P2_CORE0 1317.02 –1563.82 –1317.02 –1563.82 292 WRF_RX5G_GND1P2_CORE0 1544.51 –3364.69 –1544.51 –3364.69 293 WRF_TX_GND1P2_CORE0 1018.43 –1834.38 –1018.43 –1834.38 294 WRF_TSSI_A_CORE0 1317.27 –3235.69 –1317.27 –3235.69 295 WRF_BUCK_GND1P5_CORE0 1424.35 –3533.90 –1424.35 –3533.90 296 WRF_BUCK_VDD1P5_CORE1 –2237.36 –2423.85 2237.36 –2423.85 297 WRF_GPIO_OUT_CORE0 998.51 –2273.63 –998.51 –2273.63 298 WRF_RFOUT_2G_CORE0 2279.50 –1998.02 –2279.50 –1998.02 299 WRF_RFOUT_5G_CORE1 –1801.46 –3688.00 1801.46 –3688.00 300 WRF_PA2G_VBAT_GND3P3_CORE0 1714.63 –2523.25 –1714.63 –2523.25 301 WRF_PA2G_VBAT_GND3P3_CORE1 –1126.70 –3114.13 1126.70 –3114.13 302 WRF_RFIN_5G_CORE0 2138.64 –3649.99 –2138.64 –3649.99 303 WRF_PA5G_VBAT_GND3P3_CORE0 1825.51 –3198.01 –1825.51 –3198.01 304 WRF_PA5G_VBAT_GND3P3_CORE1 –1401.46 –3225.01 1401.46 –3225.01 305 WRF_PA2G_VBAT_VDD3P3_CORE0 2279.50 –2398.01 –2279.50 –2398.01 306 WRF_PA2G_VBAT_VDD3P3_CORE0 2297.50 –2198.02 –2297.50 –2198.02 307 WRF_RX2G_GND1P2_CORE0 1488.79 –1700.51 –1488.79 –1700.51 308 WRF_BUCK_VDD1P5_CORE0 1024.35 –3633.90 –1024.35 –3633.90 309 WRF_BUCK_VDD1P5_CORE0 1224.35 –3633.90 –1224.35 –3633.90 310 WRF_BUCK_VDD1P5_CORE0 1224.35 –3433.91 –1224.35 –3433.91 311 WRF_BUCK_VDD1P5_CORE1 –2037.36 –2423.85 2037.36 –2423.85 312 WRF_BUCK_VDD1P5_CORE1 –2037.36 –2623.85 2037.36 –2623.85 313 WRF_BUCK_VDD1P5_CORE1 –2237.36 –2623.85 2237.36 –2623.85 314 WRF_PA5G_VBAT_VDD3P3_CORE1 –1601.46 –3697.00 1601.46 –3697.00 315 WRF_PA2G_VBAT_VDD3P3_CORE1 –1001.47 –3679.00 1001.47 –3679.00 316 WRF_LOGEN_GND1P2 326.11 –2303.63 –326.11 –2303.63 317 WRF_RX2G_GND1P2_CORE1 –303.96 –2888.29 303.96 –2888.29 318 WRF_CP_GND1P2 339.26 –3598.00 –339.26 –3598.00 319 WL_REG_ON –1710.77 3277.01 1710.77 3277.01 Document Number: 002-15053 Rev. *D Page 74 of 155 ADVANCE CYW4356 Table 21. 395-Bump WLCSP Coordinates (Cont.) Coordinates (0,0 center of die) No. Net Name Bump Side X Top Side Y X Y 320 BT_REG_ON –1569.35 1721.37 1569.35 1721.37 321 LDO_VDDBAT5V –1852.20 1721.37 1852.20 1721.37 322 LDO_VDDBAT5V –1852.20 1438.53 1852.20 1438.53 323 LDO_VDDBAT5V –1852.20 1155.69 1852.20 1155.69 324 VOUT_3P3 –1993.62 1297.11 1993.62 1297.11 325 VOUT_3P3 –2135.04 1155.69 2135.04 1155.69 326 VDDIO_PMU –1710.77 1297.11 1710.77 1297.11 327 LDO_VDDBAT5V –1852.20 872.84 1852.20 872.84 328 LDO_VDDBAT5V –2135.04 872.84 2135.04 872.84 329 LDO_VDDBAT5V –2276.46 1014.26 2276.46 1014.26 330 VOUT_3P3_SENSE –2276.46 1297.11 2276.46 1297.11 331 LDO_VDDBAT5V –1710.77 1862.79 1710.77 1862.79 332 VOUT_3P3 –1993.62 1579.95 1993.62 1579.95 333 VSSC –1569.35 1155.69 1569.35 1155.69 334 VSSC –1569.35 1438.53 1569.35 1438.53 335 PMU_AVSS –1569.35 2287.06 1569.35 2287.06 336 SR_VLX –1569.35 2852.74 1569.35 2852.74 337 SR_VLX –1569.35 3135.59 1569.35 3135.59 338 SR_PVSS –1852.20 3135.59 1852.20 3135.59 339 SR_VLX –1852.20 2852.74 1852.20 2852.74 340 SR_VDDBATA5V –1852.20 2569.90 1852.20 2569.90 341 VOUT_CLDO –1852.20 2287.06 1852.20 2287.06 342 LDO_VDD1P5 –1852.20 2004.21 1852.20 2004.21 343 LDO_VDDBAT5V –1993.62 1014.26 1993.62 1014.26 344 VOUT_3P3 –2135.04 1438.53 2135.04 1438.53 345 LDO_VDDBAT5V –2135.04 1721.37 2135.04 1721.37 346 VOUT_LDO3P3_B –2135.04 2004.21 2135.04 2004.21 347 LDO_VDD1P5 –2135.04 2287.06 2135.04 2287.06 348 SR_VDDBATP5V –2135.04 2569.90 2135.04 2569.90 349 SR_PVSS –2135.04 3135.59 2135.04 3135.59 350 VDDIO_PMU –1710.77 1579.95 1710.77 1579.95 351 VOUT_LNLDO –1710.77 2145.64 1710.77 2145.64 352 VOUT_CLDO –1710.77 2428.48 1710.77 2428.48 353 SR_VLX –1710.77 2711.32 1710.77 2711.32 354 SR_VLX –1710.77 2994.17 1710.77 2994.17 355 VOUT_LDO3P3_B –1993.62 1862.79 1993.62 1862.79 356 LDO_VDD1P5 –1993.62 2145.64 1993.62 2145.64 357 VOUT_CLDO –1993.62 2428.48 1993.62 2428.48 358 SR_VDDBATP5V –1993.62 2711.32 1993.62 2711.32 359 SR_VLX –1993.62 2994.17 1993.62 2994.17 Document Number: 002-15053 Rev. *D Page 75 of 155 ADVANCE CYW4356 Table 21. 395-Bump WLCSP Coordinates (Cont.) Coordinates (0,0 center of die) No. Net Name Bump Side X Top Side Y X Y 360 SR_PVSS –1993.62 3277.01 1993.62 3277.01 361 VOUT_3P3 –2276.46 1862.79 2276.46 1862.79 362 VOUT_BTLDO2P5 –2276.46 2145.64 2276.46 2145.64 363 LDO_VDD1P5 –2276.46 2428.48 2276.46 2428.48 364 SR_PVSS –2276.46 3277.01 2276.46 3277.01 365 VOUT_3P3 –2276.46 1579.95 2276.46 1579.95 366 SR_VDDBATP5V –2276.46 2711.32 2276.46 2711.32 367 PCIE_TESTP 1800.31 3068.53 –1800.31 3068.53 368 PCIE_TESTN 1966.81 2956.03 –1966.81 2956.03 369 BT_VDDC 1480.37 1005.66 –1480.37 1005.66 370 BT_VDDC 1480.37 1225.66 –1480.37 1225.66 371 BT_VDDC 1408.19 248.05 –1408.19 248.05 372 BT_VDDC 1322.34 55.02 –1322.34 55.02 373 BT_VDDC 1060.28 –1186.86 –1060.28 –1186.86 374 BT_VDDC 666.40 –198.15 –666.40 –198.15 375 BT_VDDC 617.61 –1324.61 –617.61 –1324.61 376 BT_VSSC 338.89 –475.07 –338.89 –475.07 377 BT_VSSC 1040.28 –724.53 –1040.28 –724.53 378 BT_VSSC 1063.38 1020.66 –1063.38 1020.66 379 BT_VSSC 1063.38 1320.66 –1063.38 1320.66 380 BT_VSSC 1273.37 505.67 –1273.37 505.67 381 BT_VSSC 1273.37 705.66 –1273.37 705.66 382 BT_VSSC 1273.37 1005.66 –1273.37 1005.66 383 BT_VSSC 1273.37 1225.66 –1273.37 1225.66 384 VSSC 440.99 2052.00 –440.99 2052.00 385 VSSC –1293.24 –1317.60 1293.24 –1317.60 386 VSSC –1202.10 –1504.00 1202.10 –1504.00 387 VSSC –1058.99 1451.99 1058.99 1451.99 388 VSSC –1058.99 2302.00 1058.99 2302.00 389 VSSC –959.90 279.00 959.90 279.00 390 VSSC –759.00 851.99 759.00 851.99 391 VSSC –759.00 1151.99 759.00 1151.99 392 VSSC –759.00 1451.99 759.00 1451.99 393 VSSC –759.00 2052.00 759.00 2052.00 394 VSSC –746.31 –956.00 746.31 –956.00 395 VSSC –746.31 –756.00 746.31 –756.00 Document Number: 002-15053 Rev. *D Page 76 of 155 ADVANCE CYW4356 13.3 Signal Descriptions The signal name, type, and description of each pin in the CYW4356 is listed in Table 22 and Table 23. The symbols shown under Type indicate pin directions (I/O = bidirectional, I = input, O = output) and the internal pull-up/pull-down characteristics (PU = weak internal pull-up resistor and PD = weak internal pull-down resistor), if any. Table 22. WLCSP Signal Descriptions Bump# Signal Name Type Description WLAN and Bluetooth Receive RF Signal Interface 290 WRF_RFIN_2G_CORE0 I 2.4 GHz Bluetooth and WLAN CORE0 receiver shared input 261 WRF_RFIN_2G_CORE1 I 2.4 GHz Bluetooth and WLAN CORE1 receiver shared input 302 WRF_RFIN_5G_CORE0 I 5 GHz WLAN CORE0 receiver input 260 WRF_RFIN_5G_CORE1 I 5 GHz WLAN CORE1 receiver input 298 WRF_RFOUT_2G_CORE0 O 2.4 GHz WLAN CORE0 PA output 279 WRF_RFOUT_2G_CORE1 O 2.4 GHz WLAN CORE1 PA output 280 WRF_RFOUT_5G_CORE0 O 5 GHz WLAN CORE0 PA output 299 WRF_RFOUT_5G_CORE1 O 5 GHz WLAN CORE1 PA output 294 WRF_TSSI_A_CORE0 I 5 GHz TSSI CORE0 input from an optional external power amplifier/power detector. 276 WRF_TSSI_A_CORE1 I 5 GHz TSSI CORE1 input from an optional external power amplifier/power detector. 297 WRF_GPIO_OUT_CORE0 I/O GPIO or 2.4 GHz TSSI CORE0 input from an optional external power amplifier/power detector 258 WRF_GPIO_OUT_CORE1 I/O GPIO or 2.4 GHz TSSI CORE1 input from an optional external power amplifier/power detector Programmable RF switch control lines. The control lines are programmable via the driver and NVRAM file. RF Switch Control Lines 66 RF_SW_CTRL_0 O 175 RF_SW_CTRL_1 O 186 RF_SW_CTRL_2 O 193 RF_SW_CTRL_3 O 86 RF_SW_CTRL_4 O 183 RF_SW_CTRL_5 O 190 RF_SW_CTRL_6 O 197 RF_SW_CTRL_7 O 181 RF_SW_CTRL_8 O 187 RF_SW_CTRL_9 O 194 RF_SW_CTRL_10 O 202 RF_SW_CTRL_11 O 184 RF_SW_CTRL_12 O 191 RF_SW_CTRL_13 O 198 RF_SW_CTRL_14 O 207 RF_SW_CTRL_15 O WLAN PCI Express Interface 174 PCIE_CLKREQ_L Document Number: 002-15053 Rev. *D OD PCIe clock request signal which indicates when the REFCLK to the PCIe interface can be gated. 1 = the clock can be gated 0 = the clock is required Page 77 of 155 ADVANCE CYW4356 Table 22. WLCSP Signal Descriptions (Cont.) Bump# Signal Name Type Description 180 PCIE_PERST_L I (PU) PCIe System Reset. This input is the PCIe reset as defined in the PCIe base specification version 1.1. 9 PCIE_RDN0 I Receiver differential pair (×1 lane) 8 PCIE_RDP0 I 4 PCIE_REFCLKN I 3 PCIE_REFCLKP I 5 PCIE_TDN0 O 6 PCIE_TDP0 O 165 PCIE_PME_L OD PCI power management event output. Used to request a change in the device or system power state. The assertion and deassertion of this signal is asynchronous to the PCIe reference clock. This signal has an open-drain output structure, as per the PCI Bus Local Bus Specification, revision 2.3. 367 PCIE_TESTP – PCIe test pin 368 PCIE_TESTN – PCIE Differential Clock inputs (negative and positive). 100 MHz differential. Transmitter differential pair (×1 lane) WLAN SDIO Bus Interface These signals can support alternate functionality depending on package and host interface mode. See Table 27. 78 SDIO_CLK I SDIO clock input 81 SDIO_CMD I/O SDIO command line 82 SDIO_DATA_0 I/O SDIO data line 0 77 SDIO_DATA_1 I/O SDIO data line 1 80 SDIO_DATA_2 I/O SDIO data line 2 79 SDIO_DATA_3 I/O SDIO data line 3 WLAN GPIO Interface The GPIO signals can be multiplexed via software and the JTAG_SEL pin to support other functions. See Table 24 and Table 27 for additional details. 218 GPIO_0 I/O 219 GPIO_1 I/O 220 GPIO_2 I/O 221 GPIO_3 I/O 229 GPIO_4 I/O 237 GPIO_5 I/O 236 GPIO_6 I/O 189 GPIO_7 I/O 196 GPIO_8 I/O 205 GPIO_9 I/O 185 GPIO_10 I/O 192 GPIO_11 I/O 199 GPIO_12 I/O 182 GPIO_13 I/O 188 GPIO_14 I/O 195 GPIO_15 I/O Document Number: 002-15053 Rev. *D Programmable GPIO pins Page 78 of 155 ADVANCE CYW4356 Table 22. WLCSP Signal Descriptions (Cont.) Bump# Signal Name Type Description JTAG Interface 239 JTAG_SEL I/O JTAG select: pull high to select the JTAG interface. If the JTAG interface is not used this pin may be left floating or connected to ground. Note: See Table 27 for the JTAG signal pins. 251 WRF_XTAL_IN I XTAL oscillator input 253 WRF_XTAL_OUT O XTAL oscillator output 159 LPO_IN I External sleep clock input (32.768 kHz) 161 CLK_REQ O Reference clock request (shared by BT and WLAN). If not used, this can be no-connect. Clocks Bluetooth/FM Transceiver 49 BT_RF O Bluetooth PA output 61 FM_RFIN I FM radio antenna port 60 FM_RFAUX I FM radio auxiliary antenna port 54 FM_AOUT1 O FM DAC output 1 55 FM_AOUT2 O FM DAC output 2 Bluetooth PCM 179 BT_PCM_CLK I/O PCM clock; can be master (output) or slave (input) 173 BT_PCM_IN I PCM data input 177 BT_PCM_OUT O PCM data output 163 BT_PCM_SYNC I/O PCM sync; can be master (output) or slave (input). Bluetooth USB Interface 164 BT_USB_DN I/O USB (Host) data negative. Negative terminal of the USB transceiver. 169 BT_USB_DP I/O USB (Host) data positive. Positive terminal of the USB transceiver. Bluetooth UART 172 BT_UART_CTS_L I UART clear-to-send. Active-low clear-to-send signal for the HCI UART interface. 178 BT_UART_RTS_L O UART request-to-send. Active-low request-to-send signal for the HCI UART interface. BT LED control pin. 162 BT_UART_RXD I UART serial input. Serial data input for the HCI UART interface. 157 BT_UART_TXD O UART serial output. Serial data output for the HCI UART interface. Bluetooth/FM I2S 167 BT_I2S_CLK I/O I2S clock, can be master (output) or slave (input). 171 BT_I2S_DO I/O I2S data output 156 BT_I2S_DI I/O I2S data input 158 BT_I2S_WS I/O I2S WS; can be master (output) or slave (input). I/O Bluetooth general-purpose I/O Bluetooth GPIOs 155 BT_GPIO_2 Document Number: 002-15053 Rev. *D Page 79 of 155 ADVANCE CYW4356 Table 22. WLCSP Signal Descriptions (Cont.) Bump# Signal Name Type Description 154 BT_GPIO_3 I/O Bluetooth general-purpose I/O 168 BT_GPIO_4 I/O Bluetooth general-purpose I/O 153 BT_GPIO_5 I/O Bluetooth general-purpose I/O Miscellaneous 319 WL_REG_ON I Used by PMU to power up or power down the internal CYW4356 regulators used by the WLAN section. Also, when deasserted, this pin holds the WLAN section in reset. This pin has an internal 200 kΩ pull-down resistor that is enabled by default. It can be disabled through programming. 320 BT_REG_ON I Used by PMU to power up or power down the internal CYW4356 regulators used by the Bluetooth/FM section. Also, when deasserted, this pin holds the Bluetooth/FM section in reset. This pin has an internal 200 kΩ pull-down resistor that is enabled by default. It can be disabled through programming. 176 BT_DEV_WAKE I/O Bluetooth DEV_WAKE 170 BT_HOST_WAKE I/O Bluetooth HOST_WAKE NC Do not connect these pins to anything. Leave them floating. 12–29, NC 99–101, 31, 33, 35, 38 Integrated Voltage Regulators 340 SR_VDDBATA5V I Quiet VBAT 348 SR_VDDBATP5V I Power VBAT 336 SR_VLX O Cbuck switching regulator output. Refer to Table 44 for details of the inductor and capacitor required on this output. 342 LDO_VDD1P5 I LNLDO input 327 LDO_VDDBAT5V I LDO VBAT. 249 WRF_XTAL_VDD1P5 I XTAL LDO input (1.35V) 254 WRF_XTAL_VDD1P2 O XTAL LDO output (1.2V) 351 VOUT_LNLDO O Output of LNLDO 341 VOUT_CLDO O Output of core LDO 362 VOUT_BTLDO2P5 O Output of BT LDO 346 VOUT_LDO3P3_B O Output of 3.3V LDO 324 VOUT_3P3 O LDO 3.3V output 330 VOUT_3P3_SENSE O Voltage sense pin for LDO 3.3V output PWR Bluetooth PA power supply Bluetooth Supplies 46 BT_PAVDD2P5 44 BT_LNAVDD1P2 PWR Bluetooth LNA power supply 42 BT_IFVDD1P2 PWR Bluetooth IF block power supply 47 BT_PLLVDD1P2 PWR Bluetooth RF PLL power supply 50 BT_VCOVDD1P2 PWR Bluetooth RF power supply 148, 149, 150,151 BT_VDDIO PWR Core supply Document Number: 002-15053 Rev. *D Page 80 of 155 ADVANCE CYW4356 Table 22. WLCSP Signal Descriptions (Cont.) Bump# Signal Name Type Description FM Transceiver Supplies – FM_LNAVCOVDD1P2 PWR FM LNA and VCO 1.2V power supply 62 FM_LNAVDD1P2 PWR FM LNA 1.2V power supply 64 FM_VCOVDD1P2 PWR FM VCO 1.2V power supply 59 FM_PLLVDD1P2 PWR FM PLL 1.2V power supply 52 FM_AUDIOVDD1P2 PWR FM AUDIO power supply PWR Internal capacitor-less CORE0 LDO supply WLAN Supplies 277 WRF_BUCK_VDD1P5_CORE0 296 WRF_BUCK_VDD1P5_CORE1 PWR Internal capacitor-less CORE1 LDO supply 262 WRF_SYNTH_VBAT_VDD3P3 PWR Synth VDD 3.3V supply 289 WRF_PADRV_VBAT_VDD3P3_CORE0 PWR CORE0 PA Driver VBAT supply 264 WRF_PADRV_VBAT_VDD3P3_CORE1 PWR CORE1 PA Driver VBAT supply 269 WRF_PA5G_VBAT_VDD3P3_CORE0 PWR 5 GHz CORE0 PA 3.3V VBAT supply 266 WRF_PA5G_VBAT_VDD3P3_CORE1 PWR 5 GHz CORE1 PA 3.3V VBAT supply 305 WRF_PA2G_VBAT_VDD3P3_CORE0 PWR 2 GHz CORE0 PA 3.3V VBAT supply 285 WRF_PA2G_VBAT_VDD3P3_CORE1 PWR 2 GHz CORE1 PA 3.3V VBAT supply 270 WRF_MMD_VDD1P2 PWR 1.2V supply 262 WRF_PFD_VDD1P2 PWR 1.2V supply Document Number: 002-15053 Rev. *D Page 81 of 155 ADVANCE CYW4356 Table 22. WLCSP Signal Descriptions (Cont.) Bump# Signal Name Type Description Miscellaneous Supplies 160 OTP_VDD33 PWR OTP 3.3V supply 67, 74, 87, VDDC 103, 107– 115, 127– 129, 134– 140, 203, 204, 208– 211, 213, 224, 228, 241, 242, 246 PWR 1.2V core supply for WLAN 206, 222, 231 PWR 1.8V–3.3V supply for WLAN. Must be directly connected to PMU_VDDIO and BT_VDDIO on the PCB. 145, 147, BT_VDDC 369– 375, PWR 1.2V core supply for BT 326 VDDIO_PMU PWR 1.8V–3.3V supply for PMU controls. Must be directly connected to VDDIO and BT_VDDIO on the PCB. 76 VDDIO_SD PWR 1.8V–3.3V supply for SDIO pads and PCIe out-of-band signals. 223 VDDIO_RF PWR IO supply for RF switch control pads (3.3V). 98 VDDC_98 PWR 1.2V supply from VOUT_CLDO (341, 352, 357). 102 VDDC_102 PWR 1.2V supply from VOUT_CLDO (341, 352, 357). 143 AVDD_BBPLL PWR Baseband PLL supply. 11 PCIE_PLL_AVDD1P2 PWR 1.2V supply for PCIe PLL. (This pin should be left unconnected (NC) for SDIO operation.) 7 PCIE_RXTX_AVDD1P2 PWR 1.2V supply for PCIE TX and RX. (This pin should be left unconnected (NC) for SDIO operation.) 230 VDDIO_PCIE PWR Supply the same voltage to this pin as that used for the PCIE out-of-band signals (that is, PCIE_PME_L). 250 WRF_VCO_GND1P2 GND VCO/LOGEN ground 281 WRF_AFE_GND1P2_CORE0 GND CORE0 AFE ground 267 WRF_AFE_GND1P2_CORE1 GND CORE1 AFE ground 295 WRF_BUCK_GND1P5_CORE0 GND Internal capacitor-less CORE0 LDO ground 256 WRF_BUCK_GND1P5_CORE1 GND Internal capacitor-less CORE1 LDO ground 275 WRF_LNA_2G_GND1P2_CORE0 GND 2 GHz internal CORE0 LNA ground 282 WRF_LNA_2G_GND1P2_CORE1 GND 2 GHz internal CORE1 LNA ground 273 WRF_LNA_5G_GND1P2_CORE0 GND 5 GHz internal CORE0 LNA ground 283 WRF_LNA_5G_GND1P2_CORE1 GND 5 GHz internal CORE1 LNA ground 293 WRF_TX_GND1P2_CORE0 GND TX CORE0 ground 255 WRF_TX_GND1P2_CORE1 GND TX CORE1 ground 288 WRF_PADRV_VBAT_GND3P3_CORE0 GND PAD CORE0 ground 265 WRF_PADRV_VBAT_GND3P3_CORE1 GND PAD CORE1 ground VDDIO Ground 248 WRF_XTAL_GND1P2 GND XTAL ground 291, 307 WRF_RX2G_GND1P2_CORE0 GND RX 2GHz CORE0 ground Document Number: 002-15053 Rev. *D Page 82 of 155 ADVANCE CYW4356 Table 22. WLCSP Signal Descriptions (Cont.) Bump# Signal Name Type Description 259, 317 WRF_RX2G_GND1P2_CORE1 GND RX 2GHz CORE1 ground 292 WRF_RX5G_GND1P2_CORE0 GND RX 5GHz CORE0 ground 257 WRF_RX5G_GND1P2_CORE1 GND RX 5GHz CORE1 ground 252, 316 WRF_LOGEN_GND1P2 GND LOGEN ground 278 WRF_LOGENG_GND1P2 GND LOGEN ground 268, 030 WRF_PA5G_VBAT_GND3P3_CORE0 GND 5 GHz PA CORE0 ground 286, 304 WRF_PA5G_VBAT_GND3P3_CORE1 GND 5 GHz PA CORE1 ground 272, 300 WRF_PA2G_VBAT_GND3P3_CORE0 GND 2 GHz PA CORE0 ground 284, 301 WRF_PA2G_VBAT_GND3P3_CORE1 GND 2 GHz PA CORE1 ground 271 WRF_MMD_GND1P2 GND Ground 274, 318 WRF_CP_GND1P2 GND Ground 263 WRF_PFD_GND1P2 GND Ground 68–73, 75, VSSC 83–85, 88–95, 104–106, 116–122, 130, 200, 201, 217, 232–235, 254–245, 333, 334, 384–395 GND Core ground for WLAN and BT 338, 349, 360, 364 SR_PVSS GND Power ground 335 PMU_AVSS GND Quiet ground 30, 32, 34, GND 36, 37, 39, 96, 97 GND – 40 BT_PAVSS GND Bluetooth PA ground 43 BT_IFVSS GND Bluetooth IF block ground 48 BT_PLLVSS GND Bluetooth PLL ground 51 BT_VCOVSS GND Bluetooth VCO ground 65 FM_VCOVSS GND FM VCO ground 63 FM_LNAVSS GND FM LNA ground 58 FM_PLLVSS GND FM PLL ground 53 FM_AUDIOVSS GND FM AUDIO ground 144 AVSS_BBPLL GND Baseband PLL ground 10 PCIE_AVSS GND PCIe ground 1 PCIE_RXTX_AVSS GND PCIe ground 2 PCIE_PLL_AVSS GND PCIe ground 17, 18, 23, RGND 26 GND Ground – GND Ground BTRGND Document Number: 002-15053 Rev. *D Page 83 of 155 ADVANCE CYW4356 Table 23. WLBGA Signal Descriptions Ball# Signal Name Type Description WLAN and Bluetooth Receive RF Signal Interface N1 WRF_RFIN_2G_CORE0 I 2.4 GHz Bluetooth and WLAN CORE0 receiver shared input V7 WRF_RFIN_2G_CORE1 I 2.4 GHz Bluetooth and WLAN CORE1 receiver shared input V1 WRF_RFIN_5G_CORE0 I 5 GHz WLAN CORE0 receiver input V12 WRF_RFIN_5G_CORE1 I 5 GHz WLAN CORE1 receiver input P1 WRF_RFOUT_2G_CORE0 O 2.4 GHz WLAN CORE0 PA output V8 WRF_RFOUT_2G_CORE1 O 2.4 GHz WLAN CORE1 PA output U1 WRF_RFOUT_5G_CORE0 O 5 GHz WLAN CORE0 PA output V11 WRF_RFOUT_5G_CORE1 O 5 GHz WLAN CORE1 PA output U3 WRF_TSSI_A_CORE0 I 5 GHz TSSI CORE0 input from an optional external power amplifier/power detector. T11 WRF_TSSI_A_CORE1 I 5 GHz TSSI CORE1 input from an optional external power amplifier/power detector. R4 WRF_GPIO_OUT_CORE0 I/O GPIO or 2.4 GHz TSSI CORE0 input from an optional external power amplifier/power detector R9 WRF_GPIO_OUT_CORE1 I/O GPIO or 2.4 GHz TSSI CORE1 input from an optional external power amplifier/power detector Programmable RF switch control lines. The control lines are programmable via the driver and NVRAM file. RF Switch Control Lines R7 RF_SW_CTRL_0 O N8 RF_SW_CTRL_1 O P9 RF_SW_CTRL_2 O N7 RF_SW_CTRL_3 O N5 RF_SW_CTRL_4 O P7 RF_SW_CTRL_5 O P5 RF_SW_CTRL_6 O M8 RF_SW_CTRL_7 O K12 RF_SW_CTRL_8 O J11 RF_SW_CTRL_9 O M12 RF_SW_CTRL_10 O L9 RF_SW_CTRL_11 O J9 RF_SW_CTRL_12 O K10 RF_SW_CTRL_13 O M10 RF_SW_CTRL_14 O L8 RF_SW_CTRL_15 O WLAN PCI Express Interface D5 PCIE_CLKREQ_L OD PCIe clock request signal which indicates when the REFCLK to the PCIe interface can be gated. 1 = the clock can be gated 0 = the clock is required C4 PCIE_PERST_L I (PU) PCIe System Reset. This input is the PCIe reset as defined in the PCIe base specification version 1.1. Document Number: 002-15053 Rev. *D Page 84 of 155 ADVANCE CYW4356 Table 23. WLBGA Signal Descriptions (Cont.) Ball# B1 Signal Name PCIE_RDN0 Type I Description Receiver differential pair (×1 lane) C1 PCIE_RDP0 I A5 PCIE_REFCLKN I A4 PCIE_REFCLKP A3 PCIE_TDN0 A2 PCIE_TDP0 O C5 PCIE_PME_L OD PCI power management event output. Used to request a change in the device or system power state. The assertion and deassertion of this signal is asynchronous to the PCIe reference clock. This signal has an open-drain output structure, as per the PCI Bus Local Bus Specification, revision 2.3. C3 PCIE_TESTP – PCIe test pin C2 PCIE_TESTN – I O PCIE Differential Clock inputs (negative and positive). 100 MHz differential. Transmitter differential pair (×1 lane) WLAN SDIO Bus Interface Note: These signals can support alternate functionality depending on package and host interface mode. See Table 27 for additional details. A8 SDIO_CLK I SDIO clock input A9 SDIO_CMD I/O SDIO command line B9 SDIO_DATA_0 I/O SDIO data line 0 C9 SDIO_DATA_1 I/O SDIO data line 1 B8 SDIO_DATA_2 I/O SDIO data line 2 C8 SDIO_DATA_3 I/O SDIO data line 3 WLAN GPIO Interface Note: The GPIO signals can be multiplexed via software and the JTAG_SEL pin to support other functions. See Table 24 and Table 27 for additional details. G11 GPIO_0 I/O F10 GPIO_1 I/O F11 GPIO_2 I/O G9 GPIO_3 I/O H9 GPIO_4 I/O F9 GPIO_5 I/O F8 GPIO_6 I/O E7 GPIO_7 I/O F7 GPIO_8 I/O E6 GPIO_9 I/O H12 GPIO_10 I/O – GPIO_11 I/O – GPIO_12 I/O – GPIO_13 I/O – GPIO_14 I/O – GPIO_15 I/O Document Number: 002-15053 Rev. *D Programmable GPIO pins Page 85 of 155 ADVANCE CYW4356 Table 23. WLBGA Signal Descriptions (Cont.) Ball# Signal Name Type Description JTAG Interface D9 JTAG_SEL I/O JTAG select: pull high to select the JTAG interface. If the JTAG interface is not used this pin may be left floating or connected to ground. See Table 27 for the JTAG signal pins. WRF_XTAL_IN I XTAL oscillator input Clocks P12 N12 WRF_XTAL_OUT O XTAL oscillator output F6 LPO_IN I External sleep clock input (32.768 kHz) F4 CLK_REQ O Reference clock request (shared by BT and WLAN). If not used, this can be no-connect. O Bluetooth PA output Bluetooth/FM Transceiver L1 BT_RF H1 FM_RFIN I FM radio antenna port – FM_RFAUX I FM radio auxiliary antenna port E1 FM_AOUT1 O FM DAC output 1 F1 FM_AOUT2 O FM DAC output 2 Bluetooth PCM M6 BT_PCM_CLK I/O PCM clock; can be master (output) or slave (input) J4 BT_PCM_IN I PCM data input H4 BT_PCM_OUT O PCM data output K6 BT_PCM_SYNC I/O PCM sync; can be master (output) or slave (input). Bluetooth USB Interface E5 BT_USB_DN I/O USB (Host) data negative. Negative terminal of the USB transceiver. F5 BT_USB_DP I/O USB (Host) data positive. Positive terminal of the USB transceiver. Bluetooth UART L5 BT_UART_CTS_L I UART clear-to-send. Active-low clear-to-send signal for the HCI UART interface. K5 BT_UART_RTS_L O UART request-to-send. Active-low request-to-send signal for the HCI UART interface. BT LED control pin. H5 BT_UART_RXD I UART serial input. Serial data input for the HCI UART interface. J5 BT_UART_TXD O UART serial output. Serial data output for the HCI UART interface. Bluetooth/FM I2S J6 BT_I2S_CLK I/O I2S clock, can be master (output) or slave (input). G6 BT_I2S_DO I/O I2S data output G5 BT_I2S_DI I/O I2S data input L6 BT_I2S_WS I/O I2S WS; can be master (output) or slave (input). Document Number: 002-15053 Rev. *D Page 86 of 155 ADVANCE CYW4356 Table 23. WLBGA Signal Descriptions (Cont.) Ball# Signal Name Type Description Bluetooth GPIO A6 BT_GPIO_2 I/O Bluetooth general-purpose I/O D7 BT_GPIO_3 I/O Bluetooth general-purpose I/O K4 BT_GPIO_4 I/O Bluetooth general-purpose I/O A7 BT_GPIO_5 I/O Bluetooth general-purpose I/O Miscellaneous A10 WL_REG_ON I Used by PMU to power up or power down the internal CYW4356 regulators used by the WLAN section. Also, when deasserted, this pin holds the WLAN section in reset. This pin has an internal 200 kΩ pull-down resistor that is enabled by default. It can be disabled through programming. D10 BT_REG_ON I Used by PMU to power up or power down the internal CYW4356 regulators used by the Bluetooth/FM section. Also, when deasserted, this pin holds the Bluetooth/FM section in reset. This pin has an internal 200 kΩ pull-down resistor that is enabled by default. It can be disabled through programming. L4 BT_DEV_WAKE I/O Bluetooth DEV_WAKE J3 BT_HOST_WAKE I/O Bluetooth HOST_WAKE Integrated Voltage Regulators B11 SR_VDDBATA5V I Quiet VBAT B12 SR_VDDBATP5V I Power VBAT A11 SR_VLX O Cbuck switching regulator output. Refer to Table 44 for details of the inductor and capacitor required on this output. C12 LDO_VDD1P5 I LNLDO input E12 LDO_VDDBAT5V I LDO VBAT. P11 WRF_XTAL_VDD1P5 I XTAL LDO input (1.35V) N10 WRF_XTAL_VDD1P2 O XTAL LDO output (1.2V) D11 VOUT_LNLDO O Output of LNLDO C11 VOUT_CLDO O Output of core LDO D12 VOUT_BTLDO2P5 O Output of BT LDO E11 VOUT_LDO3P3_B O Output of 3.3V LDO F12 VOUT_3P3 O LDO 3.3V output – VOUT_3P3_SENSE O Voltage sense pin for LDO 3.3V output Bluetooth Supplies M1 BT_PAVDD2P5 PWR Bluetooth PA power supply K1 BT_LNAVDD1P2 PWR Bluetooth LNA power supply K3 BT_IFVDD1P2 PWR Bluetooth IF block power supply K2 BT_PLLVDD1P2 PWR Bluetooth RF PLL power supply J1 BT_VCOVDD1P2 PWR Bluetooth RF power supply K7 BT_VDDIO PWR Core supply PWR FM LNA and VCO 1.2V power supply FM Transceiver Supplies G1 FM_LNAVCOVDD1P2 Document Number: 002-15053 Rev. *D Page 87 of 155 ADVANCE CYW4356 Table 23. WLBGA Signal Descriptions (Cont.) Ball# Signal Name Type Description – FM_LNAVDD1P2 PWR FM LNA 1.2V power supply – FM_VCOVDD1P2 PWR FM VCO 1.2V power supply F3 FM_PLLVDD1P2 PWR FM PLL 1.2V power supply E2 FM_AUDIOVDD1P2 PWR FM AUDIO power supply WLAN Supplies U4 WRF_BUCK_VDD1P5_CORE0 PWR Internal capacitor-less CORE0 LDO supply R11 WRF_BUCK_VDD1P5_CORE1 PWR Internal capacitor-less CORE1 LDO supply V6 WRF_SYNTH_VBAT_VDD3P3 PWR Synth VDD 3.3V supply R3 WRF_PADRV_VBAT_VDD3P3_CORE0 PWR CORE0 PA Driver VBAT supply T9 WRF_PADRV_VBAT_VDD3P3_CORE1 PWR CORE1 PA Driver VBAT supply T1 WRF_PA5G_VBAT_VDD3P3_CORE0 PWR 5 GHz CORE0 PA 3.3V VBAT supply V10 WRF_PA5G_VBAT_VDD3P3_CORE1 PWR 5 GHz CORE1 PA 3.3V VBAT supply R1 WRF_PA2G_VBAT_VDD3P3_CORE0 PWR 2 GHz CORE0 PA 3.3V VBAT supply V9 WRF_PA2G_VBAT_VDD3P3_CORE1 PWR 2 GHz CORE1 PA 3.3V VBAT supply T5 WRF_MMD_VDD1P2 PWR 1.2V supply T4 WRF_PFD_VDD1P2 PWR 1.2V supply Miscellaneous Supplies – OTP_VDD33 PWR OTP 3.3V supply B7, D4, E9, G10, J8, J12, L10, M7 VDDC PWR 1.2V core supply for WLAN E10 VDDIO PWR 1.8V–3.3V supply for WLAN. Must be directly connected to PMU_VDDIO and BT_VDDIO on the PCB. E4, H3, M5 BT_VDDC PWR 1.2V core supply for BT – VDDIO_PMU PWR 1.8V–3.3V supply for PMU controls. Must be directly connected to VDDIO and BT_VDDIO on the PCB. E8 VDDIO_SD PWR 1.8V–3.3V supply for SDIO pads and PCIe out-of-band signals. H11 VDDIO_RF PWR IO supply for RF switch control pads (3.3V) H7 AVDD_BBPLL PWR Baseband PLL supply B3 PCIE_PLL_AVDD1P2 PWR 1.2V supply for PCIe PLL. (This pin should be left unconnected (NC) for SDIO operation.) B2 PCIE_RXTX_AVDD1P2 PWR 1.2V supply for PCIE TX and RX. (This pin should be left unconnected (NC) for SDIO operation.) U6 WRF_VCO_GND1P2 GND VCO/LOGEN ground P4 WRF_AFE_GND1P2_CORE0 GND CORE0 AFE ground R8 WRF_AFE_GND1P2_CORE1 GND CORE1 AFE ground V4 WRF_BUCK_GND1P5_CORE0 GND Internal capacitor-less CORE0 LDO ground R12 WRF_BUCK_GND1P5_CORE1 GND Internal capacitor-less CORE1 LDO ground N2 WRF_LNA_2G_GND1P2_CORE0 GND 2 GHz internal CORE0 LNA ground Ground Document Number: 002-15053 Rev. *D Page 88 of 155 ADVANCE CYW4356 Table 23. WLBGA Signal Descriptions (Cont.) Ball# Signal Name Type Description U7 WRF_LNA_2G_GND1P2_CORE1 GND 2 GHz internal CORE1 LNA ground V2 WRF_LNA_5G_GND1P2_CORE0 GND 5 GHz internal CORE0 LNA ground U12 WRF_LNA_5G_GND1P2_CORE1 GND 5 GHz internal CORE1 LNA ground P3 WRF_TX_GND1P2_CORE0 GND TX CORE0 ground T8 WRF_TX_GND1P2_CORE1 GND TX CORE1 ground T3 WRF_PADRV_VBAT_GND3P3_CORE0 GND PAD CORE0 ground T10 WRF_PADRV_VBAT_GND3P3_CORE1 GND PAD CORE1 ground N11 WRF_XTAL_GND1P2 GND XTAL ground N3 WRF_RX2G_GND1P2_CORE0 GND RX 2GHz CORE0 ground T7 WRF_RX2G_GND1P2_CORE1 GND RX 2GHz CORE1 ground V3 WRF_RX5G_GND1P2_CORE0 GND RX 5GHz CORE0 ground T12 WRF_RX5G_GND1P2_CORE1 GND RX 5GHz CORE1 ground R6 WRF_LOGEN_GND1P2 GND LOGEN ground R5 WRF_LOGENG_GND1P2 GND LOGEN ground T2, U2 WRF_PA5G_VBAT_GND3P3_CORE0 GND 5 GHz PA CORE0 ground U10, U11 WRF_PA5G_VBAT_GND3P3_CORE1 GND 5 GHz PA CORE1 ground P2, R2 WRF_PA2G_VBAT_GND3P3_CORE0 GND 2 GHz PA CORE0 ground U8, U9 WRF_PA2G_VBAT_GND3P3_CORE1 GND 2 GHz PA CORE1 ground T6 WRF_MMD_GND1P2 GND Ground V5 WRF_CP_GND1P2 GND Ground U5 WRF_PFD_GND1P2 GND Ground C10, D3, D6, G4, G8, G12, L7, L11, M4 VSSC GND Core ground for WLAN and BT A12 SR_PVSS GND Power ground B10 PMU_AVSS GND Quiet ground L2 BT_PAVSS GND Bluetooth PA ground M3 BT_IFVSS GND Bluetooth IF block ground L3 BT_PLLVSS GND Bluetooth PLL ground J2 BT_VCOVSS GND Bluetooth VCO ground G2 FM_VCOVSS GND FM VCO ground H2 FM_LNAVSS GND FM LNA ground G3 FM_PLLVSS GND FM PLL ground F2 FM_AUDIOVSS GND FM AUDIO ground G7 AVSS_BBPLL GND Baseband PLL ground – PCIE_AVSS GND PCIe ground B4 PCIE_RXTX_AVSS GND PCIe ground B5 PCIE_PLL_AVSS GND PCIe ground – RGND GND Ground Document Number: 002-15053 Rev. *D Page 89 of 155 ADVANCE CYW4356 Table 23. WLBGA Signal Descriptions (Cont.) Ball# – Signal Name Type BTRGND Description GND Ground NC No connect. Leave floating. No Connect B6, C6, C7 NC 13.4 WLAN/BT GPIO Signals and Strapping Options The pins listed in Table 24 and Table 25 are sampled at power-on reset (POR) to determine the various operating modes. Sampling occurs a few milliseconds after an internal POR or deassertion of the external POR. After the POR, each pin assumes the GPIO or alternative function specified in the signal descriptions table. Each strapping option pin has an internal pull-up (PU) or pull-down (PD) resistor that determines the default mode. To change the mode, connect an external PU resistor to VDDIO or a PD resistor to GND, using a 10 kΩ resistor or less. Note: Refer to the reference board schematics for more information. Table 24. WLAN GPIO Functions and Strapping Options Default Function Pin Name GPIO_4 0 Description 1: SPROM is present 0: SPROM is absent (default). Applicable in PCIe Host mode. In SDIO Host mode, sdioPadVddio is 3.3V while set to 1, and 1.8V while set to 0. GPIO_[10, 9, 8] [0,0,0] Host interface selection: see Table 26. GPIO_12 1 1 = HTAvailable (default) 0 = ResourceModeInit is ALPAvailable. On PCBs, use a pull-down and tie to ALP clock mode. Table 25. BT GPIO Functions and Strapping Options Pin Name BT_GPIO4 Default Function 0 Description 1: BT Serial Flash is present. 0: BT Serial Flash is absent (default) Table 26. GPIO_[10, 9, 8] Host Interface Selection GPIO_[10, 9, 8] Bit Setting WLAN Host Interface Mode Bluetooth Mode 000 SDIO BTUART or BTUSB; BT tPorts stand-alone. 010 Not used BTUART or BTUSB; BT tPorts stand-alone 011 PCIE BTUART or BTUSB; BT tPorts stand-alone Document Number: 002-15053 Rev. *D Page 90 of 155 ADVANCE CYW4356 13.5 GPIO Alternative Signal Functions Note: For all new designs, use GPIO_6 for SECI_IN instead of GPIO_4. For existing designs, GPIO_4 can be still used for SECI_IN provided the strapping requirements discussed in “WLAN/BT GPIO Signals and Strapping Options” are fully satisfied. Table 27. GPIO Alternative Signal Functions Pin Names Test Mode FAST UART SPROM BSC 4 5 Miscellaneous-0 (JTAG_SEL = 1) GCI Miscellaneous-1 Miscellaneous-2 UART 7 8 9 3 PWDOG 10 Function Select 0 2 6 Additional Functionality GPIO_0 TEST_GPIO_0 FAST_UAR T _RX – BSC_CLK – GCI_GPIO_4 SDIO_SEP_I SDIO_SEP_I UART_DBG PWDOG NT NT _TX _GPIO_0 _OD WL_HOST_W AKE GPIO_1 TEST_GPIO_1 FAST_UAR T _TX – BSC _SDA RF_DISABLE_L GCI_GPIO_5 – – UART_DBG PWDOG _RX _GPIO_1 WL_DEV_WA KE GPIO_2 TEST_GPIO_2 FAST_UAR T _CTS_IN – N/A TCK GCI_GPIO_1 – – – – – GPIO_3 TEST_GPIO_3 FAST_UAR T _RTS_OUT – N/A TMS GCI_GPIO_0 – – – – – GPIO_4 TEST_GPIO_4 – – N/A TDI SECI_INa – – UART_DBG _RX – – GPIO_5 TEST_GPIO_5 – – N/A TDO SECI_OUT – – UART_DBG _TX – – GPIO_6 TEST_GPIO_6 – – N/A TRST_L GCI_GPIO_2 SECI_INa – – – – GPIO_7 TEST_GPIO_7 FAST_UAR SPROM_C T S _RTS_OUT BSC_SDA PMU_TEST_ GCI_GO PIO_3 – UART_DBG_TX – PWDOG _GPIO_2 WL_LED (For WLBGA) GPIO_8 TEST_GPIO_8 FAST_UAR SPROM_C T LK _CTS_IN BSC_CLK – – – –– – PWDOG _GPIO_3 – GPIO_9 TEST_GPIO_9 FAST_UAR T _RX – SECI_OUT PALDO_PD – – PWDOG _GPIO_4 – – GCI_GPIO_4 – – – PWDOG _GPIO_5 – GPIO_1 TEST_G0 PIO_10 SPROM_MI PALDO _PU FAST_UAR SPROM_M – T O _TX Document Number: 002-15053 Rev. *D – Page 91 of 155 ADVANCE CYW4356 Table 27. GPIO Alternative Signal Functions (Cont.) Pin Names Test Mode FAST UART SPROM BSC 4 5 Miscellaneous-0 (JTAG_SEL = 1) GCI Miscellaneous-1 Miscellaneous-2 UART 7 8 9 3 PWDOG 10 Function Select 0 2 6 Additional Functionality GPIO_11 TEST_GPIO_11 FAST_UAR T_RX – PALDO _PU – GCI_GPIO_5 PALDO_PD – – – – GPIO_1 TEST_G2 PIO_12 FAST_UAR T _TX – – – GCI_GPIO_1 – – – – GPIO_1 TEST_G3 PIO_13 – – – – GCI_GPIO_0 – – – – – GPIO_1 TEST_G4 PIO_14 FAST_UAR T _RTS_OUT – – – GCI_GPIO_2 – – UART_DBG _RX – – GPIO_1 TEST_G5 PIO_15 FAST_UAR T_CTS_IN – – – GCI_GPIO_3 – – UART_DBG _TX – – Note: 1. GPIO_0 and WL_DEV_WAKE signals are selected by using software. 2. SDIO_PADVDDIO = 1 (not in straps table) is set to 3.3V by default for all packages. 3. GPIO_7 can be used as WL_LED in WLBGA package. a. For all new designs, use GPIO_6 for SECI_IN instead of GPIO_4. For existing designs, GPIO_4 can be still used for SECI_IN provided the strapping requirements discussed in “WLAN/ BT GPIO Signals and Strapping Options” are fully satisfied. Table 28 defines status for all CYW4356 GPIOs based on the tristate test mode. Table 28. GPIO Status Vs. Test Modes Test Mode Function Select Status for All GPIOs TRISTATE_IND 12 Input disable TRISTATE_PDN 13 Pull down TRISTATE_PUP 14 Pull up TRISTATE 15 Tristate Document Number: 002-15053 Rev. *D Page 92 of 155 ADVANCE CYW4356 13.6 I/O States The following notations are used in Table 29: ■ I: Input signal ■ O: Output signal ■ I/O: Input/Output signal ■ PU = Pulled up ■ PD = Pulled down ■ NoPull = Neither pulled up nor pulled down ■ Where applicable, the default value is shown in bold brackets (for example, [default value]) Table 29. I/O States Name WL_REG_ON I/O Keepera Active Mode Low Power State/Sleep (All Power Present) Power-downb (BT_REG_ON and WL_REG_ON Held Low) Out-of-Reset; (WL_REG_ON High Before SW Down- and BT_REG_ON = 0) load (BT_REG_ON and VDDIOs Are High; WL_REG_ON Present High) Power Rail I N I: PD I: PD I: PD (of 200K) Pull-down can be disabled Pull-down can be disabled I: PD (of 200K) I: PD (of 200K) – I/O Y Open drain or push-pull Programmable Active high Open drain or push-pull Programmable Active high High-Z, NoPull Open drain Active high Open drain Active high BT_VDDI O BT_HOST_WAK I/O E Y I/O: PU, PD, NoPull Programmable I/O: PU, PD, NoPull Programmable High-Z, NoPull I: PD I: PD BT_REG_ON CLK_REQ BT_DEV_WAKE BT_GPIO 5 BT_GPIO 4 I: Floating, but input disabled BT_GPIO 2, 3 BT_UART_CTS I BT_UART_RTS O Y BT_UART_RXD I BT_UART_TXD O SDIO Data I/O SDIO CMD SDIO_CLK I N I: NoPull; PU programmable I: NoPull O: NoPull O: NoPull I: PU I: NoPull O: NoPull O: NoPull I/O: PU (SDIO Mode) I: PU (SDIO Mode) I: NoPull I: noPull Document Number: 002-15053 Rev. *D I: PU I: PU High-Z, NoPull I: PU I: PU High-Z, NoPull I: PU (SDIO Mode) I: PU (SDIO Mode) I: NoPull I: NoPull VDDIO_S D Page 93 of 155 ADVANCE CYW4356 Table 29. I/O States (Cont.) Name BT_PCM_CLK I/O I/O Keepera Y Active Mode I: NoPullc Low Power State/Sleep (All Power Present) I: NoPullc Power-downb (BT_REG_ON and WL_REG_ON Held Low) High-Z, NoPull Out-of-Reset; (WL_REG_ON High Before SW Down- and BT_REG_ON = 0) load (BT_REG_ON and VDDIOs Are High; WL_REG_ON Present High) I: PD I: PD Power Rail BT_VDDI O BT_PCM_IN BT_PCM_OUT BT_PCM_SYNC I: Floating, but input disabled BT_I2S_WS I: NoPulld I: NoPulld I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] I: PD BT_I2S_CLK BT_I2S_DI BT_I2S_DO GPIO_0 I/O Y GPIO_1 Y GPIO_2 Y High-Z, NoPull I: NoPull I: NoPull I: PD I: PD GPIO_3 Y GPIO_4 Y I/O: PU, PD, NoPull Programmable [PD] I/O: PU, PD, NoPull Programmable [PD] GPIO_5 Y I/O: PU, PD, NoPull Programmable [PD] I/O: PU, PD, NoPull Programmable [PD] I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] I: NoPull I: NoPull I/O: PU, PD, NoPulle I/O: PU, PD, NoPulle Ie Ie GPIO_6 Y GPIO_7 Y GPIO_8 Y GPIO_9 Y GPIO_10 Y I/O: PU, PD, NoPull Programmable [PD] I/O: PU, PD, NoPull Programmable [PD] I: PD I: PD GPIO_11 Y I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] I: NoPull I: NoPull GPIO_12 Y I/O: PU, PD, NoPull Programmable [PU] I/O: PU, PD, NoPull Programmable [PU] I: PU I: PU I/O: PU, PD, NoPull Programmable [NoPull] I/O: PU, PD, NoPull Programmable [NoPull] I: NoPull I: NoPull GPIO_13 Y GPIO_14 Y GPIO_15 Y Document Number: 002-15053 Rev. *D VDDIO Page 94 of 155 ADVANCE CYW4356 Table 29. I/O States (Cont.) Name RF_SW_CTRL_X I/O Keepera Y Active Mode O: NoPull Low Power State/Sleep (All Power Present) O: NoPull Power-downb (BT_REG_ON and WL_REG_ON Held Low) Out-of-Reset; (WL_REG_ON High Before SW Down- and BT_REG_ON = 0) load (BT_REG_ON and VDDIOs Are High; WL_REG_ON Present High) O: NoPull Power Rail : NoPull a. Keeper column: N = pad has no keeper. Y = pad has a keeper. Keeper is always active except in Power-down state. If there is no keeper, and it is an input and there is Nopull, then the pad should be driven to prevent leakage due to floating pad (for example, SDIO_CLK). b. In the Power-down state (xx_REG_ON=0): High-Z; NoPull => the pad is disabled because power is not supplied. c. Depending on whether the PCM interface is enabled and the configuration of PCM is in master or slave mode, it can be either input or output. d. Depending on whether the I2S interface is enabled and the configuration of I2S is in master or slave mode, it can be either input or output. e. For WLBGA these GPIOs have a PD in all states. For WLCSP these GPIOs have a PU in all states. Document Number: 002-15053 Rev. *D Page 95 of 155 ADVANCE CYW4356 14. DC Characteristics 14.1 Absolute Maximum Ratings Caution! The absolute maximum ratings in Table 30 indicate levels where permanent damage to the device can occur, even if these limits are exceeded for only a brief duration. Functional operation is not guaranteed under these conditions. Operation at absolute maximum conditions for extended periods can adversely affect long-term reliability of the device. Table 30. Absolute Maximum Ratings Rating Symbol DC supply for VBAT and PA driver supplya VBAT Value –0.5 to +6.0 Unit V DC supply voltage for digital I/O VDDIO –0.5 to 3.9 V DC supply voltage for RF switch I/Os VDDIO_RF –0.5 to 3.9 V DC input supply voltage for CLDO and LNLDO – –0.5 to 1.575 V DC supply voltage for RF analog VDDRF –0.5 to 1.32 V DC supply voltage for core VDDC –0.5 to 1.32 V WRF_TCXO_VDD – –0.5 to 3.63 V Maximum undershoot voltage for I/Ob Vundershoot –0.5 V Maximum overshoot voltage for I/Ob Vovershoot VDDIO + 0.5 V Maximum junction temperature Tj 125 °C a. The maximum continuous voltage is 5.25V. Voltage transients up to 6.0V for up to 10 seconds, cumulative duration over the lifetime of the device, are allowed. Voltage transients as high as 5.5V for up to 250 seconds, cumulative duration over the lifetime of the device, are allowed. b. Duration not to exceed 25% of the duty cycle. 14.2 Environmental Ratings The environmental ratings are shown in Table 31. Table 31. Environmental Ratings Characteristic Value Units Conditions/Comments Ambient Temperature (TA) –30 to +85 °C Functional operationa Storage Temperature –40 to +125 °C – Relative Humidity Less than 60 % Storage Less than 85 % Operation a. Functionality is guaranteed but specifications require derating at extreme temperatures; see the specification tables for details. 14.3 Electrostatic Discharge Specifications Extreme caution must be exercised to prevent electrostatic discharge (ESD) damage. Proper use of wrist and heel grounding straps to discharge static electricity is required when handling these devices. Always store the unused material in its antistatic packaging. Table 32. ESD Specifications Pin Type Symbol Condition ESD Rating Unit ESD, handling reference: NQY00083, Section 3.4, Group D9, Table B ESD_HAND_HBM Human body model contact 1K for WLBGA; discharge per 1.5K for WLCSP JEDEC EID/JESD22-A114 V CDM ESD_HAND_CDM Charged device model contact discharge per JEDEC EIA/JESD22-C101 V Document Number: 002-15053 Rev. *D 300 for WLBGA; 500 for WLCSP Page 96 of 155 ADVANCE CYW4356 14.4 Recommended Operating Conditions and DC Characteristics Caution! Functional operation is not guaranteed outside of the limits shown in Table 33, and operation outside these limits for extended periods can adversely affect long-term reliability of the device. Table 33. Recommended Operating Conditions and DC Characteristics Parameter Symbol Value Minimum Typical Unit Maximum DC supply voltage for VBAT VBAT 3.0a – 5.25b V DC supply voltage for core VDD 1.14 1.2 1.26 V DC supply voltage for RF blocks in chip VDDRF 1.14 1.2 1.26 V DC supply voltage for TCXO input buffer WRF_TCXO_VDD 1.62 1.8 1.98 V DC supply voltage for digital I/O VDDIO, VDDIO_SD 1.62 – 3.63 V DC supply voltage for RF switch I/Os VDDIO_RF 3.3 3.46 V External TSSI input TSSI 0.15 – 0.95 V Internal POR threshold Vth_POR 0.4 – 0.7 V 3.13 SDIO Interface I/O Pins and PCIe Out-of-band Signals PCIE_PERST_L, PCIE_PME_L, and PCIE_CLKREQ_L For VDDIO_SD = 1.8V: Input high voltage VIH 1.27 – – V Input low voltage VIL – – 0.58 V Output high voltage @ 2 mA VOH 1.40 – – V Output low voltage @ 2 mA VOL – – 0.45 V Input high voltage VIH 0.625 × VDDIO – – V Input low voltage VIL – – 0.25 × VDDIO V Output high voltage @ 2 mA VOH 0.75 × VDDIO – – V Output low voltage @ 2 mA VOL – – 0.125 × VDDIO V Input high voltage VIH 0.65 × VDDIO – – V Input low voltage VIL – – 0.35 × VDDIO V Output high voltage @ 2 mA VOH VDDIO – 0.45 – – V Output low voltage @ 2 mA VOL – – 0.45 V Input high voltage VIH 2.00 – – V Input low voltage VIL – – 0.80 V Output high voltage @ 2 mA VOH VDDIO – 0.4 – – V Output low Voltage @ 2 mA VOL – 0.40 V VOH VDDIO – 0.4 – – V For VDDIO_SD = 3.3V: Other Digital I/O Pins For VDDIO = 1.8V: For VDDIO = 3.3V: – RF Switch Control Output Pinsc For VDDIO_RF = 3.3V: Output high voltage @ 2 mA Document Number: 002-15053 Rev. *D Page 97 of 155 ADVANCE CYW4356 Table 33. Recommended Operating Conditions and DC Characteristics (Cont.) Parameter Symbol Value Minimum Typical Unit Maximum Output low voltage @ 2 mA VOL – – 0.40 V Input capacitance CIN – – 5 pF a. The CYW4356 is functional across this range of voltages. Optimal RF performance specified in the data sheet, however, is guaranteed only for 3.13V < VBAT < 4.8V. b. The maximum continuous voltage is 5.25V. Voltage transients up to 6.0V for up to 10 seconds, cumulative duration over the lifetime of the device, are allowed. Voltage transients as high as 5.5V for up to 250 seconds, cumulative duration over the lifetime of the device, are allowed. c. Programmable 2 mA to 16 mA drive strength. Default is 10 mA. Document Number: 002-15053 Rev. *D Page 98 of 155 ADVANCE CYW4356 15. Bluetooth RF Specifications Unless otherwise stated, limit values apply for the conditions specified in Table 31 and Table 33. Typical values apply for an ambient temperature of +25°C. Figure 36. RF Port Location for Bluetooth Testing BCM4356 RF Switch (0.5 dB Insertion Loss) WLAN Tx Filter BT Tx WLAN/BT Rx Antenna Port Chip Port RF Port Note: All Bluetooth specifications are measured at the chip port unless otherwise specified. Document Number: 002-15053 Rev. *D Page 99 of 155 ADVANCE CYW4356 Table 34. Bluetooth Receiver RF Specifications Parameter Conditions Minimum Typical Maximum Unit Note: The specifications in this table are measured at the chip port output unless otherwise specified. General Frequency range RX sensitivity – 2402 – 2480 MHz GFSK, 0.1% BER, 1 Mbps – –93.5 – dBm /4-DQPSK, 0.01% BER, 2 Mbps – –95.5 – dBm 8-DPSK, 0.01% BER, 3 Mbps – –89.5 – dBm Input IP3 – –16 – – dBm Maximum input at antenna – – – –20 dBm – – –90.0 –80.0 dBm RX LO Leakage 2.4 GHz band Interference Performancea C/I co-channel GFSK, 0.1% BER – 8 11 dB C/I 1 MHz adjacent channel GFSK, 0.1% BER – –7 0 dB C/I 2 MHz adjacent channel GFSK, 0.1% BER – –38 –30 dB C/I 3 MHz adjacent channel GFSK, 0.1% BER – –56 –40 dB C/I image channel GFSK, 0.1% BER – –31 –9 dB C/I 1 MHz adjacent to image channel GFSK, 0.1% BER – –46 –20 dB C/I co-channel /4-DQPSK, 0.1% BER – 9 13 dB C/I 1 MHz adjacent channel /4-DQPSK, 0.1% BER – –11 0 dB C/I 2 MHz adjacent channel /4-DQPSK, 0.1% BER – –39 –30 dB C/I 3 MHz adjacent channel /4-DQPSK, 0.1% BER – –55 –40 dB C/I image channel /4-DQPSK, 0.1% BER – –23 –7 dB C/I 1 MHz adjacent to image channel /4-DQPSK, 0.1% BER – –43 –20 dB C/I co-channel 8-DPSK, 0.1% BER – 17 21 dB C/I 1 MHz adjacent channel 8-DPSK, 0.1% BER – –4 5 dB C/I 2 MHz adjacent channel 8-DPSK, 0.1% BER – –37 –25 dB C/I 3 MHz adjacent channel 8-DPSK, 0.1% BER – –53 –33 dB C/I Image channel 8-DPSK, 0.1% BER – –16 0 dB C/I 1 MHz adjacent to image channel 8-DPSK, 0.1% BER – –37 –13 dB Out-of-Band Blocking Performance (CW) 30–2000 MHz 0.1% BER – –10.0 – dBm 2000–2399 MHz 0.1% BER – –27 – dBm 2498–3000 MHz 0.1% BER – –27 – dBm 3000 MHz–12.75 GHz 0.1% BER – –10.0 – dBm WCDMA – –13.5 – dBm 776–849 MHz WCDMA – –13.8 – dBm 824–849 MHz GSM850 – –13.5 – dBm 824–849 MHz WCDMA – –14.3 – dBm 880–915 MHz E-GSM – –13.1 – dBm 880–915 MHz WCDMA – –13.1 – dBm Out-of-Band Blocking Performance, Modulated Interferer GFSK (1 Mbps)b 698–716 MHz Document Number: 002-15053 Rev. *D Page 100 of 155 ADVANCE CYW4356 Table 34. Bluetooth Receiver RF Specifications (Cont.) Parameter Conditions Minimum Typical Maximum Unit 1710–1785 MHz GSM1800 – –18.1 – dBm 1710–1785 MHz WCDMA – –17.4 – dBm 1850–1910 MHz GSM1900 – –19.4 – dBm 1850–1910 MHz WCDMA – –18.8 – dBm 1880–1920 MHz TD-SCDMA – –19.7 – dBm 1920–1980 MHz WCDMA – –19.6 – dBm 2010–2025 MHz TD–SCDMA – –20.4 – dBm 2500–2570 MHz WCDMA – –20.4 – dBm 2500–2570 MHzc Band 7 – –30.5 – dBm 2300–2400 MHzd Band 40 – –34.0 – dBm 2570–2620 MHze Band 38 – –30.8 – dBm 2545–2575 MHzf XGP Band – –29.5 – dBm WCDMA – –9.8 – dBm 776–794 MHz WCDMA – –9.7 – dBm 824–849 MHz GSM850 – –10.7 – dBm /4-DPSK (2 Mbps)b 698–716 MHz 824–849 MHz WCDMA – –11.4 – dBm 880–915 MHz E-GSM – –10.4 – dBm 880–915 MHz WCDMA – –10.2 – dBm 1710–1785 MHz GSM1800 – –15.8 – dBm 1710–1785 MHz WCDMA – –15.4 – dBm 1850–1910 MHz GSM1900 – –16.6 – dBm 1850–1910 MHz WCDMA – –16.4 – dBm 1880–1920 MHz TD-SCDMA – –17.9 – dBm 1920–1980 MHz WCDMA – –16.8 – dBm 2010–2025 MHz TD-SCDMA – –18.6 – dBm 2500–2570 MHz WCDMA – –20.4 – dBm 2500–2570 MHzc Band 7 – –31.9 – dBm 2300–2400 MHzd Band 40 – –35.3 – dBm 2570–2620 MHze Band 38 – –31.8 – dBm XGP Band – –31.1 – dBm 698–716 MHz WCDMA – –12.6 – dBm 776–794 MHz WCDMA – –12.6 – dBm 824–849 MHz GSM850 – –12.7 – dBm 824–849 MHz WCDMA – –13.7 – dBm 880–915 MHz E-GSM – –12.8 – dBm 880–915 MHz WCDMA – –12.6 – dBm 1710–1785 MHz GSM1800 – –18.1 – dBm 1710–1785 MHz WCDMA – –17.4 – dBm 1850–1910 MHz GSM1900 – –19.1 – dBm 1850–1910 MHz WCDMA – –18.6 – dBm 2545–2575 MHzf 8-DPSK (3 Mbps)b Document Number: 002-15053 Rev. *D Page 101 of 155 ADVANCE CYW4356 Table 34. Bluetooth Receiver RF Specifications (Cont.) Parameter Conditions Minimum Typical Maximum Unit 1880–1920 MHz TD-SCDMA – –19.3 – dBm 1920–1980 MHz WCDMA – –18.9 – dBm 2010–2025 MHz TD-SCDMA – –20.4 – dBm 2500–2570 MHz WCDMA – –21.4 – dBm 2500–2570 MHzc Band 7 – –31.0 – dBm 2300–2400 MHzd Band 40 – –34.5 – dBm 2570–2620 MHze Band 38 – –31.2 – dBm 2545–2575 MHzf XGP Band – –30.0 – dBm 30 MHz–1 GHz – –95 –62 dBm 1–12.75 GHz – –70 –47 dBm 851–894 MHz – –147 – dBm/Hz 925–960 MHz – –147 – dBm/Hz 1805–1880 MHz – –147 – dBm/Hz Spurious Emissions 1930–1990 MHz – –147 – dBm/Hz 2110–2170 MHz – –147 – dBm/Hz a. The maximum value represents the actual Bluetooth specification required for Bluetooth qualification as defined in the version 4.1 specification. b. Bluetooth reference level for the wanted signal at the Bluetooth Chip port = at 3 dB desense for each data rate. c. Interferer: 2560 MHz, BW=10 MHz; measured at 2480 MHz. d. Interferer: 2360 MHz, BW=10 MHz; measured at 2402 MHz. e. Interferer: 2380 MHz, BW=10 MHz; measured at 2480 MHz. f. Interferer: 2355 MHz, BW=10 MHz; measured at 2480 MHz. Table 35. Bluetooth Transmitter RF Specifications Parameter Conditions Minimum Typical Maximum Unit Note: The specifications in this table are measured at the Chip port output unless otherwise specified. General Frequency range 2402 – 2480 MHz Basic rate (GFSK) TX power at Bluetooth – 13.0 – dBm QPSK TX power at Bluetooth – 10.0 – dBm 8PSK TX power at Bluetooth – 10.0 – dBm Power control step 2 4 8 dB – – 0.93 1 MHz M – N = the frequency range for which the spurious emission is measured relative to the transmit center frequency. – –38 –26.0 dBc – –31 –20.0 dBm – –43 –40.0 dBm Output power is with TCA and TSSI enabled. GFSK In-Band Spurious Emissions –20 dBc BW EDR In-Band Spurious Emissions 1.0 MHz < |M – N| < 1.5 MHz 1.5 MHz < |M – N| < 2.5 MHz |M – N| 2.5 MHza Document Number: 002-15053 Rev. *D Page 102 of 155 ADVANCE CYW4356 Table 35. Bluetooth Transmitter RF Specifications (Cont.) Parameter Conditions Minimum Typical Maximum Unit Out-of-Band Spurious Emissions 30 MHz to 1 GHz – – – –36.0 b,c b,d,e dBm 1 GHz to 12.75 GHz – – – –30.0 1.8 GHz to 1.9 GHz – – – –47.0 dBm dBm 5.15 GHz to 5.3 GHz – – – –47.0 dBm – – –103 – dBm GPS Band Spurious Emissions Spurious emissions Out-of-Band Noise Floorf 65–108 MHz FM RX – –147 – dBm/Hz 776–794 MHz CDMA2000 – –147 – dBm/Hz 869–960 MHz cdmaOne, GSM850 – –147 – dBm/Hz 925–960 MHz E-GSM – –147 – dBm/Hz 1570–1580 MHz GPS – –146 – dBm/Hz 1805–1880 MHz GSM1800 – –145 – dBm/Hz 1930–1990 MHz GSM1900, cdmaOne, WCDMA – –144 – dBm/Hz 2110–2170 MHz WCDMA – –141 – dBm/Hz 2500–2570 MHz Band 7 – –140 – dBm 2300–2400 MHz Band 40 – –140 – dBm 2570–2620 MHz Band 38 – –140 – dBm 2545–2575 MHz XGP Band – –140 – dBm a. The typical number is measured at ± 3 MHz offset. b. The maximum value represents the value required for Bluetooth qualification as defined in the v4.1 specification. c. The spurious emissions during Idle mode are the same as specified in Table 35. d. Specified at the Bluetooth Antenna port. e. Meets this specification using a front-end band-pass filter. f. Transmitted power in cellular and FM bands at the Bluetooth Antenna port. See Figure 36 for location of the port. Document Number: 002-15053 Rev. *D Page 103 of 155 ADVANCE CYW4356 Table 36. Local Oscillator Performance Parameter Minimum Typical Maximum Unit LO Performance Lock time – 72 – µs Initial carrier frequency tolerance – ±25 ±75 kHz DH1 packet – ±8 ±25 kHz DH3 packet – ±8 ±40 kHz DH5 packet – ±8 ±40 kHz Drift rate – 5 20 kHz/50 µs 140 155 175 kHz Frequency Drift Frequency Deviation 00001111 sequence in payloada 10101010 sequence in payloadb Channel spacing 115 140 – kHz – 1 – MHz a. This pattern represents an average deviation in payload. b. Pattern represents the maximum deviation in payload for 99.9% of all frequency deviations. Table 37. BLE RF Specifications Parameter Conditions Minimum Frequency range – 2402 RX sensea GFSK, 0.1% BER, 1 Mbps – TX powerb – – Mod Char: delta F1 average – Mod Char: delta F2 max.c – Mod Char: ratio – Typical Maximum Unit 2480 MHz –95.5 – dBm 8.5 – dBm 225 255 275 kHz 99.9 – – % 0.8 0.95 – % a. Dirty TX is On. b. BLE TX power can be increased to compensate for front-end losses such as BPF, diplexer, switch, etc.). The output is capped at 12 dBm out. The BLE TX power at the antenna port cannot exceed the 10 dBm specification limit. c. At least 99.9% of all delta F2 max. frequency values recorded over 10 packets must be greater than 185 kHz. Document Number: 002-15053 Rev. *D Page 104 of 155 ADVANCE CYW4356 16. FM Receiver Specifications Unless otherwise stated, limit values apply for the conditions specified inTable 31 and Table 33. Typical values apply for an ambient temperature +25°C. Table 38. FM Receiver Specifications Conditionsa Parameter Minimum Typical Maximum Units RF Parameters Operating frequencyb Frequencies inclusive 65 – 108 MHz Sensitivityc FM only SNR > 26 dB – 0 – dBμV EMF – 1 – μV EMF – –6 – dBμV Measured for 30 dB SNR at the audio output. Wanted Signal: 23 dBμV EMF (14.1 μV EMF), at ± 200 kHz. – 51 – dB Receiver adjacent channel selectivityc,d At ± 400 kHz – 62 – dB Intermediate signal plus noise-tonoise ratio (S+N)/N, stereoc Vin = 20 dBμV EMF (10 μV EMF) 45 53 – dB Intermodulation performancec,d Blocker level increased until desired – at 30 dB SNR Wanted Signal: 33 dBμV EMF (45 μV EMF) Modulated Interferer: At fWanted + 400 kHz and +4 MHz CW Interferer: At fWanted + 800 kHz and + 8 MHz 55 – dBc AM suppression, monoc Vin = 23 dBμV EMF (14.1 μV EMF) 40 AM at 400 Hz with m = 0.3 No A-weighted or any other filtering applied. – – dB RDS deviation = 1.2 kHz – 16 – dBμV EMF – 6.3 – μV EMF RDS RDS sensitivitye, f RDS deviation = 2 kHz RDS selectivityf 10 – dBμV 12 – dBμV EMF – 4 – μV EMF – 6 – dBμV Wanted Signal: 33 dBμV EMF (45 μV EMF), 2 kHz RDS deviation Interferer: ∆f = 40 kHz, fmod = 1 kHz ± 200 kHz – 49 – dB ± 300 kHz – 52 – dB ± 400 kHz – 52 – dB 1.5 – – kΩ RF input impedance Antenna tuning capacitor Maximum input levelc – – SNR > 26 dB Document Number: 002-15053 Rev. *D 2.5 – 30 pF – – 113 dBμV EMF – – 446 mV EMF – – 107 dBμV Page 105 of 155 ADVANCE CYW4356 Table 38. FM Receiver Specifications (Cont.) Conditionsa Parameter RF conducted emissions (measured Local oscillator breakthrough into a 50Ω load) measured on the reference port Minimum Typical Maximum Units – – –55 dBm – – –90 dBm – 7 – dBm GSM850, E-GSM (edge), BW = 0.2 MHz, 824–849 MHz 880–915 MHz – –1 – dBm GSM DCS 1800, PCS 1900 (std/ edge), BW = 0.2 MHz, 1710–1785 MHz 1850–1910 MHz – 12 – dBm WCDMA: II(I), III(IV, X), – BW = 5 MHz, 1850–1980 MHz (1920–1980 MHz), 1710–1785 MHz (1710–1755 MHz, 1710–1770 MHz) 12 – dBm WCDMA: V(VI), VIII, XII, XIII, XIV, BW = 5 MHz, 824–849 MHz (830–840 MHz), 880–915 MHz – 5 – dBm CDMA2000, cdmaOne, BW = 1.25 MHz, 824–849 MHz, 887–925 MHz, 776–794 MHz – 0 – dBm CDMA2000, cdmaOne, BW = 1.25 MHz, 1850–1910 MHz, 1750–1780 MHz, 1920–1980 MHz – 12 – dBm Bluetooth, BW = 1 MHz, 2402–2480 MHz – 11 – dBm IEEE 802.11g/b, BW = 20 MHz, 2400–2483.5 MHz – 11 – dBm IEEE 802.11a, BW = 20 MHz, 4915–5825 MHz – 6 – dBm 2500–2570 MHz Band 7 – 11 – dBm 2300–2400 MHz Band 40 – 11 – dBm 2570–2620 MHz Band 38 – 11 – dBm 2545–2575 MHz XGP Band – 11 – dBm Frequency step – 10 – – kHz Settling time Single-frequency switch in any – direction to a frequency within the bands 88–108 MHz or 76–90 MHz. Time measured to within 5 kHz of the final frequency. 150 – µs 869–894 MHz, 925–960 MHz, 1805–1880 MHz, 1930–1990 MHz. GPS RF blocking levels at the FM antenna GSM850, E-GSM (std), input 40 dB SNR (assumes a 50Ω at BW = 0.2 MHz, the radio input and excludes spurs) 824–849 MHz 880–915 MHz Tuning Document Number: 002-15053 Rev. *D Page 106 of 155 ADVANCE CYW4356 Table 38. FM Receiver Specifications (Cont.) Conditionsa Parameter Search time Minimum Typical Maximum Units Total time for an automatic search to – sweep from 88–108 MHz or 76– 90 MHz (and reverse direction) assuming no channels are found. – 8 sec – –14.5 – –12.5 dBFS General Audio Audio output levelg Maximum audio output levelh – – – 0 dBFS Audio DAC output levelg – 72 – 88 mV rms Maximum DAC audio output levelh – – 333 – mV rms Audio DAC output level differencei – –1 – 1 dB Left and right AC mute FM input signal fully muted with DAC 60 enabled – – dB Left and right hard mute FM input signal fully muted with DAC 80 disabled – – dB Soft mute attenuation and start level Muting is performed dynamically – proportional to the FM wanted input signal C/N. The muting characteristic is fully programmable. Refer to “Audio Features” for further details. – – – Maximum signal plus noise-to-noise – ratio (S + N)/N, mono i – 69 – dB Maximum signal plus noise-to-noise – ratio (S + N)/N, stereog – 64 – dB Total harmonic distortion, mono Vin = 66 dBµV EMF (2 mV EMF), ∆f = 75 kHz, fmod = 400 Hz – – 0.8 % ∆f = 75 kHz, fmod = 1 kHz – – 0.8 % ∆f = 75 kHz, fmod = 3 kHz – – 0.8 % ∆f = 100 kHz, fmod = 1 kHz – – 1.0 % Total harmonic distortion, stereo Vin = 66 dBµV EMF (2 mV EMF) ∆f = 67.5 kHz, fmod = 1 kHz, ∆f Pilot = 7.5 kHz, L = R – 1.5 % Audio spurious productsi Range from 300 Hz to 15 kHz, with – respect to 1 kHz tone – –60 dBc Audio bandwidth, upper (–3 dB point) Vin = 66 dBµV EMF (2 mV EMF) ∆f = 8 kHz, for 50 µs 15 – – kHz – – 20 Hz –0.5 – 0.5 dB Deemphasis time constant tolerance With respect to 50 and 75 µs – – ±5 % RSSI range 3 – 83 dBµV EMF 1.41 – 14.1m µV EMF –3 – 77 dBuV – 48 – dB Audio bandwidth, lower (–3 dB point) Audio in-band ripple 100 Hz to 13 kHz, Vin = 66 dBµV EMF (2 mV EMF) ∆f = 8 kHz, for 50 µs With 1 dB resolution and ± 5 dB accuracy at room temp Stereo Decoder Stereo channel separation Forced Stereo mode Vin = 66 dBµV EMF (2 mV EMF), ∆f = 67.5 kHz, fmod = 1 kHz, ∆f Pilot = 6.75 kHz R = 0, L = 1 Document Number: 002-15053 Rev. *D Page 107 of 155 ADVANCE CYW4356 Table 38. FM Receiver Specifications (Cont.) Conditionsa Parameter Minimum Typical Maximum Units Mono stereo blend and switching Blending and switching is dynamically proportional to the FM wanted input signal C/N. The blending and switching characteristics are fully programmable. Refer to “Audio Features” on page 43 for further details. Pilot suppression Vin = 66 dBµV EMF (2 mV EMF), ∆f = 75 kHz, fmod = 1 kHz 46 – – dB Pause detection Audio level at which a pause is detected Relative to 1 kHz tone, ∆f = 22.5 kHz – – – – Four values in 3 dB steps –21 – –12 dB Audio pause duration Four values 20 – 40 ms a. Following conditions are applied to all relevant tests unless otherwise indicated: Preemphasis and deemphasis of 50 us, R = L for mono, DAC Load > 20 kΩ, BAF = 300 Hz to 15 kHz, and A-weighted filtering applied. b. Contact Cypress regarding applications that operate between 65 and 76 MHz. c. Wanted Signal: ∆f = 22.5 kHz, and fmod = 1 kHz. d. Interferer: ∆f = 22.5 kHz, and fmod = 1 kHz. e. RDS sensitivity numbers are for 87.5–108 MHz only. f. Vin = ∆f = 32 kHz, fmod = 1 kHz, ∆f Pilot = 7.5 kHz, and 95% of blocks decoded with no errors after correction. g. Vin = 66 dBµV EMF (2 mV EMF), ∆f = 22.5 kHz, fmod = 1 kHz, and ∆f Pilot = 6.75 kHz. h. Vin = 66 dBµV EMF (2 mV EMF), ∆f = 100 kHz, fmod = 1 kHz, and ∆f Pilot = 6.75 kHz. i. Vin = 66 dBµV EMF (2 mV EMF), ∆f = 22.5 kHz, and fmod = 1 kHz. Document Number: 002-15053 Rev. *D Page 108 of 155 ADVANCE CYW4356 17. WLAN RF Specifications 17.1 Introduction The CYW4356 includes an integrated dual-band direct conversion radio that supports the 2.4 GHz and the 5 GHz bands. This section describes the RF characteristics of the 2.4 GHz and 5 GHz radios. Unless otherwise stated, limit values apply for the conditions specified inTable 31 and Table 33. Typical values apply for an ambient temperature +25°C. Figure 37. Port Locations (Applies to 2.4 GHz and 5 GHz) BCM4356 RF Switch (0.5 dB Insertion Loss) WLAN Tx Filter BT Tx WLAN/BT Rx Antenna Port Chip Port RF Port 17.2 2.4 GHz Band General RF Specifications Table 39. 2.4 GHz Band General RF Specifications Item Condition Minimum Typical Maximum Unit TX/RX switch time Including TX ramp down – – 5 µs RX/TX switch time Including TX ramp up – – 2 µs Power-up and power-down ramp time DSSS/CCK modulations – – <2 µs Document Number: 002-15053 Rev. *D Page 109 of 155 ADVANCE CYW4356 17.3 WLAN 2.4 GHz Receiver Performance Specifications Note: The values in Table 40 are specified at the RF port unless otherwise noted. Table 40. WLAN 2.4 GHz Receiver Performance Specifications Parameter Condition/Notes Minimum Typical Maximum Unit Frequency range – 2400 – 2500 MHz RX sensitivity IEEE 802.11ba 1 Mbps DSSS – –96.4 – dBm SISO RX sensitivity IEEE 802.11g (10% PER for 1024 octet PSDU)a MIMO RX sensitivity IEEE 802.11g (10% PER for 1024 octet PSDU)a 2 Mbps DSSS – –94.5 – dBm 5.5 Mbps DSSS – –91.7 – dBm 11 Mbps DSSS – –89.4 – dBm 6 Mbps OFDM – –93.5 – dBm 9 Mbps OFDM – –92.1 – dBm 12 Mbps OFDM – –91.2 – dBm 18 Mbps OFDM – –88.6 – dBm 24 Mbps OFDM – –85.3 – dBm 36 Mbps OFDM – –82 – dBm 48 Mbps OFDM – –77.3 – dBm 54 Mbps OFDM – –75.8 – dBm 6 Mbps OFDM – –94.5 – dBm/core 9 Mbps OFDM – –94 – dBm/core 12 Mbps OFDM – –93.2 – dBm/core 18 Mbps OFDM – –91.6 – dBm/core 24 Mbps OFDM – –88.3 – dBm/core 36 Mbps OFDM – –85 – dBm/core 48 Mbps OFDM – –80.3 – dBm/core 54 Mbps OFDM – –78.8 – dBm/core SISO RX sensitivity IEEE 802.11n 20 MHz channel spacing for all MCS rates (10% PER for 4096 octet PSDU)a,b – Defined for default parameters: GF, MCS0 800 ns GI, and non–STBC. MCS1 – –93 – dBm –90.7 – dBm MCS2 – –88.2 – dBm MCS3 – –85.1 – dBm MCS4 – –81.5 – dBm MCS5 – –76.9 – dBm MCS6 – –75.3 – dBm MCS7 – –73.7 – dBm Document Number: 002-15053 Rev. *D Page 110 of 155 ADVANCE CYW4356 Table 40. WLAN 2.4 GHz Receiver Performance Specifications (Cont.) Parameter Condition/Notes Minimum MIMO RX sensitivity IEEE 802.11n 20 MHz channel spacing for all MCS rates (10% PER for 4096 octet PSDU)a,b – Defined for default parameters: GF, MCS0 800 ns GI, and non–STBC. MCS1 – Typical Maximum Unit –94.5 – dBm/core –93.7 – dBm/core MCS2 – –91.2 – dBm/core MCS3 – –88.1 – dBm/core MCS4 – –84.5 – dBm/core MCS5 – –79.9 – dBm/core MCS6 – –78.3 – dBm/core MCS7 – –76.7 – dBm/core MCS8 – –93 – dBm/core MCS15 – –73.7 – dBm/core SISO RX sensitivity IEEE 802.11n 40 MHz channel spacing for all MCS rates (10% PER for 4096 octet PSDU)a,b – Defined for default parameters: GF, MCS0 800 ns GI, and non–STBC. MCS1 – –90.8 – dBm –87.9 – dBm MCS2 – –85.5 – dBm MCS3 – –82 – dBm MCS4 – –78.9 – dBm MCS5 – –74.2 – dBm MCS6 – –72.7 – dBm MCS7 – –71.3 – dBm MIMO RX sensitivity IEEE 802.11n 40 MHz channel spacing for all MCS rates (10% PER for 4096 octet PSDU)a,b – Defined for default parameters: GF, MCS0 800 ns GI, and non–STBC. MCS1 – –92.3 – dBm/core –90.9 – dBm/core MCS2 – –88.5 – dBm/core MCS3 – –85 – dBm/core MCS4 – –81.9 – dBm/core MCS5 – –77.2 – dBm/core MCS6 – –75.7 – dBm/core MCS7 – –74.3 – dBm/core MCS8 – –90.8 – dBm/core MCS15 – –71.3 – dBm/core SISO RX sensitivity IEEE 802.11ac 20 MHz channel spacing for all MCS rates (10% PER for 4096 octet PSDU)a,b – Defined for default parameters: GF, MCS0, Nss 1 800 ns GI, and non–STBC MCS1, Nss 1 – –92.3 – dBm –89.9 – dBm MCS2, Nss 1 – –88.1 – dBm MCS3, Nss 1 – –84.9 – dBm MCS4, Nss 1 – –81.4 – dBm MCS5, Nss 1 – –76.9 – dBm MCS6, Nss 1 – –75.3 – dBm MCS7, Nss 1 – –73.6 – dBm MCS8, Nss 1 – –69.2 – dBm Document Number: 002-15053 Rev. *D Page 111 of 155 ADVANCE CYW4356 Table 40. WLAN 2.4 GHz Receiver Performance Specifications (Cont.) Parameter Condition/Notes Minimum MIMO RX sensitivity IEEE 802.11ac 20 MHz channel spacing for all MCS rates (10% PER for 4096 octet PSDU)a,b – Defined for default parameters: GF, MCS0, Nss 1 800 ns GI, and non–STBC MCS1, Nss 1 – Typical Maximum Unit –93.8 – dBm/core –92.9 – dBm/core MCS2, Nss 1 – –91.1 – dBm/core MCS3, Nss 1 – –87.9 – dBm/core MCS4, Nss 1 – –84.4 – dBm/core MCS5, Nss 1 – –79.9 – dBm/core MCS6, Nss 1 – –78.3 – dBm/core MCS7, Nss 1 – –76.6 – dBm/core MCS8, Nss 1 – –72.2 – dBm/core MCS0, Nss 2 – –92 – dBm/core MCS8, Nss 2 – –68.1 – dBm/core SISO RX sensitivity IEEE 802.11ac 40 MHz channel spacing for all MCS rates (10% PER for 4096 octet PSDU)a,b – Defined for default parameters: GF, MCS0, Nss 1 800 ns GI, and non–STBC. MCS1, Nss 1 – –89.5 – dBm –87 – dBm MCS2, Nss 1 – –85.2 – dBm MCS3, Nss 1 – –82 – dBm MCS4, Nss 1 – –78.8 – dBm MCS5, Nss 1 – –74.3 – dBm MCS6, Nss 1 – –72.7 – dBm MCS7, Nss 1 – –71.3 – dBm MCS8, Nss 1 – –66.9 – dBm MCS9, Nss 1 – –65.6 – dBm –91 – dBm/core –90 – dBm/core MIMO RX sensitivity IEEE 802.11ac 40 MHz channel spacing for all MCS rates (10% PER for 4096 octet PSDU)a,b – Defined for default parameters: GF, MCS0, Nss 1 800 ns GI, and non–STBC. MCS1, Nss 1 – SISO RX sensitivity IEEE 802.11ac 20/40/80 MHz channel spacing with LDPC (10% PER for 4096 octet PSDU)a,b at WLAN RF port. Defined for default parameters: GF, 800 ns GI, LDPC coding, and non–STBC. MCS2, Nss 1 – –88.2 – dBm/core MCS3, Nss 1 – –85 – dBm/core MCS4, Nss 1 – –81.8 – dBm/core MCS5, Nss 1 – –77.3 – dBm/core MCS6, Nss 1 – –75.7 – dBm/core MCS7, Nss 1 – –74.3 – dBm/core MCS8, Nss 1 – –69.9 – dBm/core MCS9, Nss 1 – –68.6 – dBm/core MCS0, Nss 2 – –89 – dBm/core MCS9, Nss 2 – –64.2 – dBm/core MCS7, Nss 1 20 MHz – –75.4 – dBm MCS8, Nss 1 20 MHz – –72.7 – dBm MCS9, Nss 1 20 MHz – –69.4 – dBm MCS7, Nss 1 40 MHz – –72.8 – dBm MCS8, Nss 1 40 MHz – –68.5 – dBm MCS9, Nss 1 40 MHz – –67.3 – dBm Document Number: 002-15053 Rev. *D Page 112 of 155 ADVANCE CYW4356 Table 40. WLAN 2.4 GHz Receiver Performance Specifications (Cont.) Parameter MIMO RX sensitivity IEEE 802.11ac 20/40/80 MHz channel spacing with LDPC (10% PER for 4096 octet PSDU)a,b at WLAN RF port. Defined for default parameters: GF, 800 ns GI, LDPC coding, and non–STBC. Condition/Notes Minimum Typical Maximum Unit MCS7, Nss 2 20 MHZ – –74 – dBm/core MCS8, Nss 2 20 MHZ – –71.2 – dBm/core MCS9, Nss 2 20 MHZ – –68.0 – dBm/core MCS7, Nss 2 40 MHz – –71.8 – dBm/core MCS8, Nss 2 40 MHz – –67 – dBm/core MCS9, Nss 2 40 MHz – –65.5 – dBm/core CDMA2000 – –24 – dBm cdmaOne – –25 – dBm Blocking level for 3 dB RX sensitivity 776–794 MHz degradation (without external 824–849 MHzd filtering)c 824–849 MHzd GSM850 – –15 – dBm 880–915 MHz E–GSM – –16 – dBm 1710–1785 MHz GSM1800 – –18 – dBm 1850–1910 MHz GSM1800 – –19 – dBm 1850–1910 MHz cdmaOne – –26 – dBm 1850–1910 MHz WCDMA – –26 – dBm 1920–1980 MHz WCDMA – –28.5 – dBm 2500–2570 MHz Band 7 – –45 – dBm 2300–2400 MHz Band 40 – –50 – dBm 2570-2620 MHz Band 38 – –45 – dBm 2545-2575 MHz XGP Band – –45 – dBm In-band static CW jammer immunity RX PER < 1%, 54 Mbps OFDM, (fc - 8 MHz < fcw < + 8 MHz) 1000 octet PSDU for: (RxSense + 23 dB < Rxlevel < max. input level) –80 – – dBm Input In–Band IP3 – –15.5 – dBm Maximum Receive Level @ 2.4 GHz LPF 3 dB Bandwidth Maximum LNA gain Minimum LNA gain – –1.5 – dBm @ 1, 2 Mbps (8% PER, 1024 octets) –3.5 – – dBm @ 5.5, 11 Mbps (8% PER, 1024 octets) –9.5 – – dBm @ 6–54 Mbps (10% PER, 1024 octets) –9.5 – – dBm @ MCS0–7 rates (10% PER, 4095 octets) –9.5 – – dBm @ MCS8–9 rates (10% PER, 4095 octets) –11.5 – – dBm – 9 – 36 MHz – – dB – – dB Adjacent channel rejection–DSSS Desired and interfering signal 30 MHz apart (Difference between interfering and –74 dBm 35 desired signal at 8% PER for 1024 1 Mbps DSSS octet PSDU with desired signal level 2 Mbps DSSS –74 dBm 35 as specified in Condition/Notes) Desired and interfering signal 25 MHz apart 5.5 Mbps DSSS –70 dBm 35 – – dB 11 Mbps DSSS –70 dBm 35 – – dB Document Number: 002-15053 Rev. *D Page 113 of 155 ADVANCE CYW4356 Table 40. WLAN 2.4 GHz Receiver Performance Specifications (Cont.) Parameter Adjacent channel rejection–OFDM (difference between interfering and desired signal (25 MHz apart) at 10% PER for 1024 octet PSDU with desired signal level as specified in Condition/Notes) Adjacent channel rejection MCS0–9 (Difference between interfering and desired signal (25 MHz apart) at 10% PER for 4096 octet PSDU with desired signal level as specified in Condition/Notes) IEEE 802.11ac Adjacent channel rejection MCS0–9 (Difference between interfering and desired signal at 10% PER for 4096 octet PSDU with desired signal level as specified in Condition/Notes) Condition/Notes Minimum Typical Maximum Unit 6 Mbps OFDM –79 dBm 16 – – dB 9 Mbps OFDM –78 dBm 15 – – dB 12 Mbps OFDM –76 dBm 13 – – dB 18 Mbps OFDM –74 dBm 11 – – dB 24 Mbps OFDM –71 dBm 8 – – dB 36 Mbps OFDM –67 dBm 4 – – dB 48 Mbps OFDM –63 dBm 0 – – dB 54 Mbps OFDM –62 dBm –1 – – dB MCS0 –79 dBm 16 – – dB MCS1 –76 dBm 13 – – dB MCS2 –74 dBm 11 – – dB MCS3 –71 dBm 8 – – dB MCS4 –67 dBm 4 – – dB MCS5 –63 dBm 0 – – dB MCS6 –62 dBm –1 – – dB MCS7 –61 dBm –2 – – dB MCS8 –59 dBm –4 – – dB MCS9 –57 dBm –6 – – dB MCS0 –82 dBm – – – dB MCS1 –80 dBm – – – dB MCS2 –77 dBm – – – dB MCS3 –74 dBm – – – dB MCS4 –70 dBm – – – dB MCS5 –66 dBm – – – dB MCS6 –65 dBm – – – dB MCS7 –64 dBm – – – dB MCS8 –59 dBm – – – dB MCS9 –57 dBm – – – dB Document Number: 002-15053 Rev. *D Page 114 of 155 ADVANCE CYW4356 Table 40. WLAN 2.4 GHz Receiver Performance Specifications (Cont.) Parameter Condition/Notes Minimum Typical Maximum Unit Maximum receiver gain – – – 95 – dB Gain control step – – – 3 – dB RSSI accuracye Range –90 dBm to –30 dBm –5 – 5 dB Range above –30 dBm –8 – 8 dB Return loss Zo = 50Ω, across the dynamic range 10 11.5 13 dB Receiver cascaded noise figure At maximum gain – 4 – dB General spurs 1–18 GHz – – –60 dBm/MHz a. Derate by 1.5 dB for –30°C to –10°C and 55°C to 85°C. b. Sensitivity degradations for alternate settings in MCS modes. MM: 0.5 dB drop, and SGI: 2 dB drop. c. The cellular standard listed for each band indicates the type of modulation used to generate the interfering signal in that band for the purpose of this test. It is not intended to indicate any specific usage of each band in any specific country. d. The blocking levels are valid for channels 1 to 11. (For higher channels, the performance may be lower due to third harmonic signals (3 × 824 MHz) falling within band.) e. The minimum and maximum values shown have a 95% confidence level. 17.4 WLAN 2.4 GHz Transmitter Performance Specifications Note: The values in Table 41 are specified at the RF port unless otherwise noted. Table 41. WLAN 2.4 GHz Transmitter Performance Specifications Parameter Frequency range Condition/Notes – Transmitted power in cellular 76–108 MHz and FM bands (at 18 dBm, 100% duty cycle, 1 776–794 MHz Mbps CCK)a 869–960 MHz FM RX Min. Typ. Max. Unit 2400 – 2500 MHz – –149 – dBm/Hz – – –162 – dBm/Hz cdmaOne, GSM850 – –162 – dBm/Hz 925–960 MHz E-GSM – –162 – dBm/Hz 1570–1580 MHz GPS – –152 – dBm/Hz 1805–1880 MHz GSM1800 – –142 – dBm/Hz 1930–1990 MHz GSM1900, cdmaOne, cdmaOne – –143 – dBm/Hz 2110–2170 MHz WCDMA – –128 – dBm/Hz 2500–2570 MHz Band 7 – –92 – dBm/Hz 2300–2400 MHz Band 40 – –95 – dBm/Hz 2570–2620 MHz Band 38 – –110 – dBm/Hz XGP Band – –110 – dBm/Hz Harmonic level (at 18 dBm with 4.8–5.0 GHz 100% duty cycle) 7.2–7.5 GHz 2545–2575 MHz 2nd harmonic – –18 – dBm/MHz 3rd harmonic – –20 – dBm/MHz General spurs (at 18 dBm with 1–18 GHz 100% duty cycle) – – – –60 dBm/MHz Document Number: 002-15053 Rev. *D Page 115 of 155 ADVANCE CYW4356 Table 41. WLAN 2.4 GHz Transmitter Performance Specifications (Cont.) Parameter Condition/Notes Min. Typ. Max. Unit EVM Does Not Exceed TX power at RF port for highest 802.11b power level setting at 25°C with (DSSS/CCK) spectral mask and EVM OFDM, BPSK complianceb OFDM, QPSK –9 dB 18 19.5 – dBm –8 dB 18 19 – dBm –13 dB 18 19 – dBm OFDM, 16-QAM –19 dB 16.5 18 – dBm OFDM, 64-QAM (R = 3/4) –25 dB 15.5 17 – dBm OFDM, 64-QAM (R = 5/6) –28 dB 14.5 16 – dBm OFDM, 256-QAM (R = 3/4, VHT20) –30 dB 13.5 15 – dBm OFDM, 256-QAM (R = 5/6, VHT20) –32 dB 12 13.5 – dBm Phase noise 37.4 MHz Crystal, Integrated from 10 kHz – to 10 MHz 0.45 – Degrees TX power control dynamic range – – – dB – ±1.5 dB 10 Closed-loop TX power variation Across full temperature and voltage – at highest power level setting range. Applies across 10 dBm to 20 dBm output power range. Carrier suppression – 15 – – dBc Gain control step – – 0.25 – dB Return loss at chip port TX Zo = 50Ω – 6 – dB a. The cellular standards listed only indicate the typical usages of that band in some countries: other standards may also be used within those bands. b. Derate by 1.5 dB for –30°C to –10°C and 55°C to 85°C, or supply voltages lower than 3.0V. Derate by 3.0 dB for supply voltages of lower than 2.7V, or supply voltages lower than 3.0V at –30°C to –10°C and 55°C to 85°C. Document Number: 002-15053 Rev. *D Page 116 of 155 ADVANCE CYW4356 17.5 WLAN 5 GHz Receiver Performance Specifications Note: The values in Table 42 are specified at the RF port unless otherwise noted. Table 42. WLAN 5 GHz Receiver Performance Specifications Parameter Frequency range Condition/Notes – SISO RX sensitivity IEEE 802.11a 6 Mbps OFDM (10% PER for 1000 octet PSDU)a 9 Mbps OFDM MIMO RX sensitivity IEEE 802.11a (10% PER for 1024 octet PSDU)a,b Min. Max. Unit 4900 – 5845 MHz – –92.5 – dBm – –91.1 – dBm 12 Mbps OFDM – –90.2 – dBm 18 Mbps OFDM – –87.6 – dBm 24 Mbps OFDM – –84.3 – dBm 36 Mbps OFDM – –81 – dBm 48 Mbps OFDM – –76.3 – dBm 54 Mbps OFDM – –74.8 – dBm 6 Mbps OFDM – –93.5 – dBm/core 9 Mbps OFDM – –93 – dBm/core 12 Mbps OFDM – –92.2 – dBm/core 18 Mbps OFDM – –90.6 – dBm/core 24 Mbps OFDM – –87.3 – dBm/core 36 Mbps OFDM – –84 – dBm/core 48 Mbps OFDM – –79.3 – dBm/core 54 Mbps OFDM – –75.8 – dBm/core SISO RX sensitivity IEEE 802.11n 20 MHz channel spacing for all MCS rates (10% PER for 4096 octet MCS0 – PSDU)a,b Defined for default parameters: MCS1 – GF, 800 ns GI, and non-STBC. MCS2 – MIMO RX sensitivity IEEE 802.11n (10% PER for 4096 octet PSDU)a,b Defined for default parameters: GF, 800 ns GI, and non-STBC. Typ. –92 – dBm –89.7 – dBm –87.2 – dBm MCS3 – –84.1 – dBm MCS4 – –80.5 – dBm MCS5 – –75.9 – dBm MCS6 – –74.3 – dBm MCS7 – –72.7 – dBm 20 MHz channel spacing for all MCS rates MCS0 – –93.5 – dBm/core MCS1 – –92.7 – dBm/core MCS2 – –90.2 – dBm/core MCS3 – –87.1 – dBm/core MCS4 – –83.5 – dBm/core MCS5 – –78.9 – dBm/core MCS6 – –77.3 – dBm/core MCS7 – –75.7 – dBm/core MCS8 – –92 – dBm/core MCS15 – –72.7 – dBm/core Document Number: 002-15053 Rev. *D Page 117 of 155 ADVANCE CYW4356 Table 42. WLAN 5 GHz Receiver Performance Specifications (Cont.) Parameter Condition/Notes Min. SISO RX sensitivity IEEE 802.11n 40 MHz channel spacing for all MCS rates (10% PER for 4096 octet MCS0 – PSDU)a,b Defined for default parameters: MCS1 – GF, 800 ns GI, and non-STBC. MCS2 – MIMO RX sensitivity IEEE 802.11n (10% PER for 4096 octet PSDU)a,b Defined for default parameters: GF, 800 ns GI, and non-STBC. SISO RX sensitivity IEEE 802.11ac (10% PER for 4096 octet PSDU)a,b Defined for default parameters: GF, 800 ns GI, and non-STBC MIMO RX sensitivity IEEE 802.11ac (10% PER for 4096 octet PSDU)a,b Defined for default parameters: GF, 800 ns GI, and non-STBC Typ. Max. Unit –89.8 – dBm –86.9 – dBm –84.5 – dBm MCS3 – –81 – dBm MCS4 – –77.9 – dBm MCS5 – –73.2 – dBm MCS6 – –71.7 – dBm MCS7 – –70.3 – dBm 40 MHz channel spacing for all MCS rates MCS0 – –91.3 – dBm/core MCS1 – –89.9 – dBm/core MCS2 – –87.5 – dBm/core MCS3 – –84 – dBm/core MCS4 – –80.9 – dBm/core MCS5 – –76.2 – dBm/core MCS6 – –74.7 – dBm/core MCS7 – –73.3 – dBm/core MCS8 – –89.8 – dBm/core MCS15 – –70.3 – dBm/core – dBm 20 MHz channel spacing for all MCS rates MCS0, Nss 1 – –91.3 MCS1, Nss 1 – –88.3 – dBm MCS2, Nss 1 – –86 – dBm MCS3, Nss 1 – –83 – dBm MCS4, Nss 1 – –79.4 – dBm MCS5, Nss 1 – –74.9 – dBm MCS6, Nss 1 – –73.3 – dBm MCS7, Nss 1 – –72.6 – dBm MCS8, Nss 1 – –68.2 – dBm – dBm/core 20 MHz channel spacing for all MCS rates MCS0, Nss 1 – –92.8 MCS1, Nss 1 – –91.3 – dBm/core MCS2, Nss 1 – –89 – dBm/core MCS3, Nss 1 – –86 – dBm/core MCS4, Nss 1 – –82.4 – dBm/core MCS5, Nss 1 – –77.9 – dBm/core MCS6, Nss 1 – –76.3 – dBm/core MCS7, Nss 1 – –75.6 – dBm/core MCS8, Nss 1 – –71.2 – dBm/core MCS0, Nss 2 – –91 – dBm/core MCS8, Nss 2 – –67.1 – dBm/core Document Number: 002-15053 Rev. *D Page 118 of 155 ADVANCE CYW4356 Table 42. WLAN 5 GHz Receiver Performance Specifications (Cont.) Parameter SISO RX sensitivity IEEE 802.11ac (10% PER for 4096 octet PSDU)a,b Defined for default parameters: GF, 800 ns GI, and non-STBC. MIMO RX sensitivity IEEE 802.11ac (10% PER for 4096 octet PSDU)a,b Defined for default parameters: GF, 800 ns GI, and non-STBC. SISO RX sensitivity IEEE 802.11ac (10% PER for 4096 octet PSDU)a,b Defined for default parameters: GF, 800 ns GI, and non-STBC. Condition/Notes Min. Typ. Max. Unit 40 MHz channel spacing for all MCS rates MCS0, Nss 1 – –88.5 – dBm MCS1, Nss 1 – –85.5 – dBm MCS2, Nss 1 – –83.7 – dBm MCS3, Nss 1 – –80.5 – dBm MCS4, Nss 1 – –77.5 – dBm MCS5, Nss 1 – –72.5 – dBm MCS6, Nss 1 – –71.7 – dBm MCS7, Nss 1 – –70.3 – dBm MCS8, Nss 1 – –65.9 – dBm MCS9, Nss 1 – –64.6 – dBm 40 MHz channel spacing for all MCS rates MCS0, Nss 1 – –90 – dBm/core MCS1, Nss 1 – –88.5 – dBm/core MCS2, Nss 1 – –86.7 – dBm/core MCS3, Nss 1 – –83.5 – dBm/core MCS4, Nss 1 – –80.5 – dBm/core MCS5, Nss 1 – –75.5 – dBm/core MCS6, Nss 1 – –74.7 – dBm/core MCS7, Nss 1 – –73.3 – dBm/core MCS8, Nss 1 – –68.9 – dBm/core MCS9, Nss 1 – –67.6 – dBm/core MCS0, Nss 2 – –88 – dBm/core MCS9, Nss 2 – –63.2 – dBm/core 80 MHz channel spacing for all MCS rates MCS0, Nss 1 – –85 – dBm MCS1, Nss 1 – –82 – dBm MCS2, Nss 1 – –80 – dBm MCS3, Nss 1 – –76.7 – dBm MCS4, Nss 1 – –73.7 – dBm MCS5, Nss 1 – –70.5 – dBm MCS6, Nss 1 – –68 – dBm MCS7, Nss 1 – –66.5 – dBm MCS8, Nss 1 – –62.3 – dBm MCS9, Nss 1 – –60.5 – dBm Document Number: 002-15053 Rev. *D Page 119 of 155 ADVANCE CYW4356 Table 42. WLAN 5 GHz Receiver Performance Specifications (Cont.) Parameter MIMO RX sensitivity IEEE 802.11ac (10% PER for 4096 octet PSDU)a,b Defined for default parameters: GF, 800 ns GI, and non-STBC. Condition/Notes Min. MIMO RX sensitivity IEEE 802.11ac 20/40/80 MHz channel spacing with LDPC (10% PER for 4096 octet PSDU)a,b at WLAN RF port. Defined for default parameters: GF, 800 ns GI, LDPC coding, and non-STBC. Max. Unit 80 MHz channel spacing for all MCS rates MCS0, Nss 1 – –86.5 – dBm/core MCS1, Nss 1 – –85 – dBm/core MCS2, Nss 1 – –83 – dBm/core MCS3, Nss 1 – –79.7 – dBm/core MCS4, Nss 1 – –76.7 – dBm/core MCS5, Nss 1 – –73.5 – dBm/core MCS6, Nss 1 – –71 – dBm/core MCS7, Nss 1 – –69.5 – dBm/core MCS8, Nss 1 – –65.3 – dBm/core MCS9, Nss 1 – –63.5 – dBm/core MCS0, Nss 2 – –84.3 – dBm/core MCS9, Nss 2 SISO RX sensitivity IEEE 802.11ac 20/40/80 MHz channel spacing with LDPC (10% PER for 4096 octet PSDU)a,b at WLAN RF port. Defined for default parameters: GF, 800 ns GI, LDPC coding, and non-STBC. Typ. – –59.5 – dBm/core MCS7, Nss 1 20 MHz – –74.4 – dBm MCS8, Nss 1 20 MHz – –71.7 – dBm MCS9, Nss 1 20 MHz – –71.4 – dBm MCS7, Nss 1 40 MHz – –71.8 – dBm MCS8, Nss 1 40 MHz – –67.5 – dBm MCS9, Nss 1 40 MHz – –66.5 – dBm MCS7, Nss 1 80 MHz – –68 – dBm MCS8, Nss 1 80 MHz – –64.3 – dBm MCS9, Nss 1 80 MHz – –62.5 – dBm MCS7, Nss 2 20 MHz – –73 – dBm/core MCS8, Nss 2 20 MHz – –70.2 – dBm/core MCS9, Nss 2 20 MHz – –66.5 – dBm/core MCS7, Nss 2 40 MHz – –70.8 – dBm/core MCS8, Nss 2 40 MHz – –66 – dBm/core MCS9, Nss 2 40 MHz – –64.7 – dBm/core MCS7, Nss 2 80 MHz – –67 – dBm/core MCS8, Nss 2 80 MHz – –62.8 – dBm/core MCS9, Nss 2 80 MHz – –60.5 – dBm/core Document Number: 002-15053 Rev. *D Page 120 of 155 ADVANCE CYW4356 Table 42. WLAN 5 GHz Receiver Performance Specifications (Cont.) Parameter Condition/Notes Alternate adjacent channel 776–794 MHz rejection d Blocking level for 3 dB RX sensi- 824–849 MHz c tivity degradation (without 824–849 MHzd external filtering) 880–915 MHz Min. Typ. Max. Unit CDMA2000 –21 – – dBm cdmaOne –20 – – dBm GSM850 –12 – – dBm E-GSM –12 – – dBm 1710–1785 MHz GSM1800 –15 – – dBm 1850–1910 MHz GSM1800 –15 – – dBm 1850–1910 MHz cdmaOne –20 – – dBm 1850–1910 MHz WCDMA –21 – – dBm 1920–1980 MHz WCDMA –21 – – dBm 2500–2570 MHz Band 7 –21 – – dBm 2300–2400 MHz Band 40 –21 – – dBm 2570–2620 MHz Band 38 –21 – – dBm 2545–2575 MHz XGP Band –21 – – dBm Document Number: 002-15053 Rev. *D Page 121 of 155 ADVANCE CYW4356 Table 42. WLAN 5 GHz Receiver Performance Specifications (Cont.) Parameter Input In-Band IP3 Condition/Notes Min. Typ. Max. Unit Maximum LNA gain – –15.5 – dBm Minimum LNA gain – –1.5 – dBm Maximum receive level @ 5.24 GHz @ 6, 9, 12 Mbps –9.5 – – dBm @ 18, 24, 36, 48, 54 Mbps –14.5 – – dBm LPF 3 dB bandwidth – 9 – 36 MHz Adjacent channel rejection (Difference between interfering and desired signal (20 MHz apart) at 10% PER for 1000 octet PSDU with desired signal level as specified in Condition/Notes) 6 Mbps OFDM 16 – – dB –79 dBm 9 Mbps OFDM –78 dBm 15 – – dB 12 Mbps OFDM –76 dBm 13 – – dB 18 Mbps OFDM –74 dBm 11 – – dB 24 Mbps OFDM –71 dBm 8 – – dB 36 Mbps OFDM –67 dBm 4 – – dB 48 Mbps OFDM –63 dBm 0 – – dB 54 Mbps OFDM –62 dBm –1 – – dB 65 Mbps OFDM –61 dBm –2 – – dB –78.5 dBm 32 – – dB –77.5 dBm 31 – – dB –75.5 dBm 29 – – dB –73.5 dBm 27 – – dB 24 Mbps OFDM –70.5 dBm 24 – – dB 36 Mbps OFDM –66.5 dBm 20 – – dB 48 Mbps OFDM –62.5 dBm 16 – – dB 54 Mbps OFDM –61.5 dBm 15 – – dB 65 Mbps OFDM –60.5 dBm (Difference between interfering 6 Mbps OFDM and desired signal (40 MHz apart) e at 10% PER for 1000 octet PSDU 9 Mbps OFDM with desired signal level as 12 Mbps OFDM specified in Condition/Notes) 18 Mbps OFDM 14 – – dB Maximum receiver gain – – 95 – dB Gain control step – – 3 – dB RSSI accuracyf Range –90 dBm to –30 dBm –5 – 5 dB Range above –30 dBm –8 – 8 dB Return loss Zo = 50Ω, across the dynamic range 10 – 13 dB Receiver cascaded noise figure At maximum gain – 5 – dB General spurs 1–18 GHz – – –65 dBm/MHz a. Derate by 1.5 dB for –30°C to –10°C and 55°C to 85°C. b. The cellular standard listed for each band indicates the type of modulation used to generate the interfering signal in that band for the purpose of this test. It is not intended to indicate any specific usage of each band in any specific country. c. The cellular standard listed for each band indicates the type of modulation used to generate the interfering signal in that band for the purpose of this test. It is not intended to indicate any specific usage of each band in any specific country. d. The blocking levels are valid for channels 1 to 11. (For higher channels, the performance may be lower due to third harmonic signals (3 × 824 MHz) falling within band.) e. For 65 Mbps, the size is 4096. f. The minimum and maximum values shown have a 95% confidence level. Document Number: 002-15053 Rev. *D Page 122 of 155 ADVANCE CYW4356 17.6 WLAN 5 GHz Transmitter Performance Specifications Note: The values in Table 43 are specified at the RF port unless otherwise noted. Table 43. WLAN 5 GHz Transmitter Performance Specifications Parameter Frequency range Transmitted power in cellular and FM bands (at 18 dBm)a Harmonic level (at 17 dBm) General spurs TX power at RF port for highest power level setting at 25°C with spectral mask and EVM complianceb Phase noise TX power control dynamic range Closed loop TX power variation at highest power level setting Carrier suppression Gain control step Return loss Condition/Notes – 76–108 MHz FMRX 776–794 MHz – 869–960 MHz cdmaOne, GSM850 1570–1580 MHz GPS 1592–1610 MHz GLONASS 1805–1880 MHz GSM1800 1850–1910 MHz GSM1900 1910–1930 MHz Band 37 1930–1990 MHz GSM1900, cdmaOne, WCDMA 2010–2075 MHz TDSCDMA 2110–2170 MHz WCDMA 2300–2370 MHz Band 40 2370–2400 MHz Band 40 2496–2530 MHz Band 41 2530–2560 MHz Band 41 2570–2690 MHz Band 41 9.8–11.570 GHz 2nd harmonic Min. 4900 – – – – – – – – – Typ. – –162 –168 –167 –170 –162 –169 –169 –168 –168 Max. 5845 – – – – – – – – – Unit MHz dBm/Hz dBm/Hz dBm/Hz dBm/Hz dBm/Hz dBm/Hz dBm/Hz dBm/Hz dBm/Hz – – – – – – – – –168 –160 –166 –162 –165 –165 –158 –30 – – – – – – – – dBm/Hz dBm/Hz dBm/Hz dBm/Hz dBm/Hz dBm/Hz dBm/Hz dBm/MHz 1–18 GHz – OFDM, –13 dB BPSK/QPSK OFDM, 16-QAM –19 dB OFDM, 64-QAM – (R = 3/4) –25 dB OFDM, 64-QAM – (R = 5/6) –28 dB OFDM, 256-QAM –30 dB (R = 3/4, VHT) OFDM, 256-QAM –32 dB (R = 5/6, VHT) 37.4 MHz Crystal, Integrated from 10 kHz to 10 MHz – – 17.5 – 18.5 –57 – dBm/MHz dBm 16 – 15 – 14 13 17.5 – 16.5 – 15.5 14.5 – – – – – – dBm dBm dBm dBm dBm dBm 11 12.5 – dBm – 0.5 – Degrees 10 – – dB Across full-temperature and voltage range. Applies across 10 to 20 dBm output power range. – – Zo = 50Ω – – ±2.0 dB 15 – – – 0.25 6 – – – dBc dB dB a. The cellular standards listed indicate only typical usages of that band in some countries. Other standards may also be used within those bands. b. Derate by 1.5 dB for –30°C to –10°C and 55°C to 85°C, or supply voltages lower than 3.0V. Derate by 3.0 dB for supply voltages of lower than 2.7V, or supply voltages lower than 3.0V at –30°C to –10°C and 55°C to 85°C. Document Number: 002-15053 Rev. *D Page 123 of 155 ADVANCE CYW4356 18. Internal Regulator Electrical Specifications Functional operation is not guaranteed outside of the specification limits provided in this section. 18.1 Core Buck Switching Regulator Table 44. Core Buck Switching Regulator (CBUCK) Specifications Specification Notes Min. Typ. Max. Units Input supply voltage (DC) DC voltage range inclusive of disturbances. 3.0 3.6 5.25a V PWM mode switching frequency CCM, Load > 100 mA VBAT = 3.6V 2.8 4 5.2 MHz PWM output current – – – 600 mA – Output current limit – 1400 Output voltage range Programmable, 30 mV steps Default = 1.35V 1.2 1.35 1.5 mA V PWM output voltage DC accuracy Includes load and line regulation. Forced PWM mode –4 – 4 % PWM ripple voltage, static Measure with 20 MHz bandwidth limit. Static Load. Max. ripple based on VBAT = 3.6V, Vout = 1.35V, Fsw = 4 MHz, 2.2 μH inductor L > 1.05 μH, Cap + Board total-ESR < 20 mΩ, Cout > 1.9 μF, ESL<200pH – 7 20 mVpp PWM mode peak efficiency Peak Efficiency at 200 mA load 78 86 – % PFM mode efficiency 10 mA load current 70 81 – % Start-up time from power down VIO already ON and steady. Time from REG_ON rising edge to CLDO reaching 1.2V – – 850 μs External inductor 0806 size, ± 30%, 0.11 ± 25% Ohms – 2.2 – μH External output capacitor Ceramic, X5R, 0402, ESR <30 mΩ at 4 MHz, ± 20%, 6.3V 2.0b 4.7 10c μF External input capacitor For SR_VDDBATP5V pin, ceramic, X5R, 0603, ESR < 30 mΩ at 4 MHz, ± 20%, 6.3V, 4.7 μF 0.67b 4.7 – μF Input supply voltage ramp-up time 0 to 4.3V 40 – – μs a. The maximum continuous voltage is 5.25V. Voltages up to 6.0V for up to 10 seconds, cumulative duration, over the lifetime of the device are allowed. Voltages as high as 5.5V for up to 250 seconds, cumulative duration, over the lifetime of the device are allowed. b. Minimum capacitor value refers to the residual capacitor value after taking into account the part–to–part tolerance, DC–bias, temperature, and aging. c. Total capacitance includes those connected at the far end of the active load. Document Number: 002-15053 Rev. *D Page 124 of 155 ADVANCE CYW4356 18.2 3.3V LDO (LDO3P3) Table 45. LDO3P3 Specifications Specification Notes Min. Typ. Max. Units 2.3 3.6 5.25a V – 0.2 – 600 mA Nominal output voltage, Vo Default = 3.3V – 3.3 – V Dropout voltage At max. load. – – 200 mV Output voltage DC accuracy Includes line/load regulation. –5 – +5 % Quiescent current No load – 100 120 μA Input supply voltage, Vin Output current Min. = Vo + 0.2V = 3.5V dropout voltage requirement must be met under maximum load for performance specifications. Maximum load (600 mA) – 5.8 6 mA Leakage current Power-Down mode, junction temperature = 85°C – 1.5 5 μA Line regulation Vin from (Vo + 0.2V) to 4.8V, max. load – – 3.5 mV/V Load regulation Load from 1 mA to 450 mA – – 0.25 mV/mA PSRR Vin ≥ Vo + 0.2V, Vo = 3.3V, Co = 4.7 μF, Max. load, 100 Hz to 100 kHz 20 – – dB LDO turn-on time Chip already powered up. – 160 250 μs External output capacitor, Co Ceramic, X5R, 0402, (ESR: 5 mΩ–240 mΩ), ± 10%, 10V 1.0b 4.7 – μF External input capacitor For SR_VDDBATA5V pin (shared with – Bandgap) Ceramic, X5R, 0402, (ESR: 30m-200 mΩ), ± 10%, 10V. Not needed if sharing VBAT capacitor 4.7 μF with SR_VDDBATP5V. 4.7 – μF a. The maximum continuous voltage is 5.25V. Voltages up to 6.0V for up to 10 seconds, cumulative duration, over the lifetime of the device are allowed. Voltages as high as 5.5V for up to 250 seconds, cumulative duration, over the lifetime of the device are allowed. b. Minimum capacitor value refers to the residual capacitor value after taking into account the part-to-part tolerance, DC-bias, temperature, and aging. Document Number: 002-15053 Rev. *D Page 125 of 155 ADVANCE CYW4356 18.3 3.3V LDO (LDO3P3_B) Table 46. LDO3P3_B Specifications Specification Input supply voltage, Vin Output current Notes Min. = Vo + 0.2V = 3.5V dropout voltage requirement must be met under maximum load for performance specifications. – Min. Typ. Max. Units 2.3 3.6 5.25a V 0.1 – 150 mA Nominal output voltage, Vo Default = 3.3V – 3.3 – V Dropout voltage At max. load. – – 200 mV Output voltage DC accuracy Includes line/load regulation. –5 – +5 % Quiescent current No load – 10 16 μA Maximum load (150 mA) – 1.38 1.4 mA Leakage current Power-Down mode, junction temperature = 85°C – – 1.5 5 μA Line regulation Vin from (Vo + 0.2V) to 4.8V, max. load – – 3.5 mV/V Load regulation Load from 1 mA to 450 mA – – 0.25 mV/mA PSRR Vin ≥ Vo + 0.2V, Vo = 3.3V, Co = 4.7 μF, Max. load, 100 Hz to 100 kHz 20 – – dB LDO turn-on time Chip already powered up. – – 150 μs External output capacitor, Co Ceramic, X5R, 0402, (ESR: 5 mΩ–240 mΩ), ± 10%, 10V 0.7b 2.2 – μF External input capacitor For SR_VDDBATA5V pin (shared with Bandgap) Ceramic, X5R, 0402 – 4.7 – μF a. The maximum continuous voltage is 5.25V. Voltages up to 6.0V for up to 10 seconds, cumulative duration, over the lifetime of the device are allowed. Voltages as high as 5.5V for up to 250 seconds, cumulative duration, over the lifetime of the device are allowed. b. Minimum capacitor value refers to the residual capacitor value after taking into account the part–to–part tolerance, DC–bias, temperature, and aging. Document Number: 002-15053 Rev. *D Page 126 of 155 ADVANCE CYW4356 18.4 2.5V LDO (BTLDO2P5) Table 47. BTLDO2P5 Specifications Specification Notes Min. Typ. Max. Units Input supply voltage Min. = 2.5V + 0.2V = 2.7V. 3.0 Dropout voltage requirement must be met under maximum load for performance specifications. 3.6 5.25a V Nominal output voltage Default = 2.5V. – 2.5 – V Output voltage programmability Range 2.2 2.5 2.8 V Accuracy at any step (including line/load regulation), load > 0.1 mA. –5 – 5 % At maximum load. – – 200 mV Dropout voltage Output current – 0.1 – 70 mA Quiescent current No load. – 8 16 μA Maximum load at 70 mA. – 660 700 μA Leakage current Power-down mode. – 1.5 5 µA Line regulation Vin from (Vo + 0.2V) to 4.8V, maximum load. – – 3.5 mV/V Load regulation Load from 1 mA to 70 mA, Vin = 3.6V. – – 0.3 mV/mA PSRR Vin ≥ Vo + 0.2V, Vo = 2.5V, Co = 2.2 μF, maximum load, 100 Hz to 100 kHz. 20 – – dB LDO turn-on time Chip already powered up. – – 150 μs In-rush current Vin = Vo + 0.15V to 4.8V, Co = 2.2 μF, No load. – – 250 mA External output capacitor, Co Ceramic, X5R, 0402, (ESR: 5–240 mΩ), ±10%, 10V 0.7b 2.2 2.64 μF External input capacitor For SR_VDDBATA5V pin (shared with – Bandgap) ceramic, X5R, 0402, (ESR: 30–200 mΩ), ±10%, 10V. Not needed if sharing VBAT 4.7 μF capacitor with SR_VDDBATP5V. 4.7 – μF a. The maximum continuous voltage is 5.25V. Voltages up to 6.0V for up to 10 seconds, cumulative duration, over the lifetime of the device are allowed. Voltages as high as 5.5V for up to 250 seconds, cumulative duration, over the lifetime of the device are allowed. b. The minimum value refers to the residual capacitor value after taking into account part–to–part tolerance, DC–bias, temperature, and aging. Document Number: 002-15053 Rev. *D Page 127 of 155 ADVANCE CYW4356 18.5 CLDO Table 48. CLDO Specifications Specification Notes Min. Typ. Max. Units Input supply voltage, Vin Min. = 1.2 + 0.15V = 1.35V dropout voltage requirement must be met under maximum load. 1.3 1.35 1.5 V Output current – 0.2 – 300 mA Output voltage, Vo Programmable in 25 mV steps. Default = 1.2.V 1.1 1.2 1.275 V Dropout voltage At max. load – – 150 mV Output voltage DC accuracy Includes line/load regulation –4 – +4 % No load – 24 – μA 300 mA load – 2.1 – mA Quiescent current Line Regulation Vin from (Vo + 0.15V) to 1.5V, maximum load – – 5 mV/V Load Regulation Load from 1 mA to 300 mA – 0.02 0.05 mV/mA Leakage Current Power down – – 20 μA Bypass mode – 1 3 μA PSRR @1 kHz, Vin ≥ 1.35V, Co = 4.7 μF 20 – Start-up Time of PMU VIO up and steady. Time from the REG_ON – rising edge to the CLDO reaching 1.2V. – 700 μs 140 180 μs 4.7 – μF 1 2.2 μF LDO Turn-on Time LDO turn-on time when rest of the chip is up – External Output Capacitor, Co Total ESR: 5 mΩ–240 mΩ External Input Capacitor Only use an external input capacitor at the – VDD_LDO pin if it is not supplied from CBUCK output. 1.32a dB a. Minimum capacitor value refers to the residual capacitor value after taking into account the part–to–part tolerance, DC–bias, temperature, and aging. Document Number: 002-15053 Rev. *D Page 128 of 155 ADVANCE CYW4356 18.6 LNLDO Table 49. LNLDO Specifications Specification Notes Min. Typ. Max. Units Input supply voltage, Vin Min. = 1.2Vo + 0.15V = 1.35V dropout voltage 1.3 requirement must be met under maximum load. 1.35 1.5 V Output Current – 0.1 – 150 mA Output Voltage, Vo Programmable in 25 mV steps. Default = 1.2V 1.1 1.2 1.275 V Dropout Voltage At maximum load – – 150 mV Output Voltage DC Accuracy Includes line/load regulation –4 – +4 % Quiescent current No load – 44 – μA Max. load – 970 990 μA Line Regulation Vin from (Vo + 0.1V) to 1.5V, max. load – – 5 mV/V Load Regulation Load from 1 mA to 150 mA – 0.02 0.05 mV/mA Leakage Current Power-down – – 10 μA Output Noise @30 kHz, 60–150 mA load Co = 2.2 μF @100 kHz, 60–150 mA load Co = 2.2 μF – – 60 35 nV/rt Hz nV/rt Hz PSRR @ 1kHz, Input > 1.35V, Co= 2.2 μF, Vo = 1.2V 20 – – dB LDO Turn-on Time LDO turn-on time when rest of chip is up – 140 180 μs External Output Capacitor, Co Total ESR (trace/capacitor): 5 mΩ–240 mΩ 0.5a 2.2 4.7 μF External Input Capacitor Only use an external input capacitor at the – VDD_LDO pin if it is not supplied from CBUCK output. Total ESR (trace/capacitor): 30 mΩ–200 mΩ 1 2.2 μF a. Minimum capacitor value refers to the residual capacitor value after taking into account the part–to–part tolerance, DC–bias, temperature, and aging. Document Number: 002-15053 Rev. *D Page 129 of 155 ADVANCE CYW4356 19. System Power Consumption Note: Unless otherwise stated, these values apply for the conditions specified in Table 33. 19.1 WLAN Current Consumption The WLAN current consumption measurements are shown in Table 50. All values in Table 50 are with the Bluetooth core in reset (that is, Bluetooth and FM are OFF). . Table 50. Typical WLAN Power Consumption Bandwidth (MHz) Mode Band (GHz) Vbat = 3.6V mA Vio = 1.8V μAa Sleep Modes OFFb – – 0.003 36 Sleepc – – 0.005 260 cored 20 2.4 1.2 260 IEEE power save, DTIM 3 1 RX cored 20 2.4 0.4 260 IEEE power save, DTIM 1 1 RX cored 20 5 1.2 260 cored 20 5 0.4 260 IEEE power save, DTIM 1 1 RX cored 40 5 1.5 260 cored 40 5 0.5 260 IEEE power save, DTIM 1 1 RX cored 80 5 2.0 260 cored 80 5 0.7 260 CCK 1 chaine 20 2.4 450 60 MCS8, Nss 1, HT20, SGIf, g, h 20 2.4 330 60 f, g, h MCS8, Nss 2, HT20, SGI 20 2.4 610 60 MCS7, SGIf, g, i 20 5 310 60 MCS15, SGIf, g, i 20 5 620 60 MCS7f, g, i 40 5 340 60 MCS9, Nss 1, SGIf, g, j 40 5 300 60 SGIf, g, j 40 5 590 60 MCS9, Nss 1, SGIf, g, j 80 5 330 60 MCS9, Nss 2, SGIf, g, j 80 5 610 60 1 Mbps, 1 RX core 20 2.4 65 60 1 Mbps, 2 RX cores 20 2.4 87 60 MCS7, HT20 1 RX corek 20 2.4 69 60 IEEE power save, DTIM 1 1 RX IEEE power save, DTIM 3 1 RX IEEE power save, DTIM 3 1 RX IEEE power save, DTIM 3 1 RX Active Modes Transmit MCS9, Nss 2, Receive MCS7, HT20 2 RX coresk 20 2.4 92 60 MCS15, HT20k 20 2.4 96 60 CRS 1 RX corel 20 2.4 66 60 20 2.4 86 60 20 5 84 60 CRS 2 RX coresl Receive MCS7, SGI 1 RX corek Receive MCS7, SGI 2 RX coresk 20 5 111 60 Receiver MCS15, SGIk 20 5 116 60 CRS 1 RX corel 20 5 79 60 20 5 103 60 40 5 101 60 CRS 2 RX coresl Receive MCS 7, SGI 1 RX corek Document Number: 002-15053 Rev. *D Page 130 of 155 ADVANCE CYW4356 Table 50. Typical WLAN Power Consumption (Cont.) Bandwidth (MHz) Mode Band (GHz) Vbat = 3.6V mA Vio = 1.8V μAa Receive MCS 7, SGI 2 RX coresk 40 5 140 60 Receive MCS 15, SGIk 40 5 151 60 CRS 1 RX corel 40 5 93 60 coresl 40 5 128 60 Receive MCS9, Nss 1, SGIk 80 5 136 60 CRS 2 RX Receive MCS9, Nss 1, SGI 2 RX coresk 80 5 189 60 Receive MCS9, Nss 2, SGIk 80 5 205 60 corel 80 5 117 60 80 5 172 60 CRS 1 RX CRS 2 RX coresl a. Specified with all pins idle (not switching) and not driving any loads. b. WL_REG_ON and BT_REG_ON low. c. Idle, not associated, or inter-beacon. d. Beacon Interval = 102.4 ms. Beacon duration = 1 ms @1 Mbps. Average current over three DTIM intervals. e. Output power per core at RF port = 21 dBm f. Duty cycle is 100%. g. Measured using packet engine test mode. h. Output power per core at RF port = 17 dBm. i. Output power per core at RF port = 17.5 dBm. j. Output power per core at RF port = 14 dBm. k. Duty cycle is 100%. Carrier sense (CS) detect/packet receive. l. Carrier sense (CCA) when no carrier is present. Document Number: 002-15053 Rev. *D Page 131 of 155 ADVANCE CYW4356 19.2 Bluetooth and FM Current Consumption The Bluetooth, BLE, and FM current consumption measurements are shown in Table 51. Note: ■ The WLAN core is in reset (WLAN_REG_ON = low) for all measurements provided in Table 51. ■ For FM measurements, the Bluetooth core is in Sleep mode. ■ The BT current consumption numbers are measured based on GFSK TX output power = 10 dBm. Table 51. Bluetooth BLE and FM Current Consumption VBAT (VBAT = 3.6V) Typical Operating Mode VDDIO (VDDIO = 1.8V) Typical Units Sleep 13 198 µA Standard 1.28s Inquiry Scan 0.217 0.197 mA P and I Scanb 440 194 µA 500 ms Sniff Master 0.168 0.195 mA 500 ms Sniff Slave 0.124 0.190 mA DM1/DH1 Master 25.3 0.024 mA DM3/DH3 Master 30.6 0.035 mA DM5/DH5 Master 31.4 0.037 mA 3DH5 Master 29.2 0.094 mA SCO HV3 Master 11.45 0.089 mA HV3 + Sniff + Scana 11.7 0.090 mA FMRX I2S Audio 8.0 – mA FMRX Analog Audio only 8.6 – mA FMRX I2S Audio + RDS 8.0 – mA FMRX Analog Audio + RDS 8.6 – mA BLE Scanb 244 196 µA BLE Scan 10 ms 21.34 0.013 mA BLE Adv—Unconnectable 1.00 sec 67 199 µA BLE Adv—Unconnectable 1.28 sec 55 199 µA BLE Adv—Unconnectable 2.00 sec 58 199 µA BLE Connected 7.5 ms 3.95 0.013 mA BLE Connected 1 sec. 57 198 µA BLE Connected 1.28 sec. 52 197 µA a. At maximum class 1 TX power, 500 ms sniff, four attempts (slave), P = 1.28s, and I = 2.56s. b. No devices present. A 1.28 second interval with a scan window of 11.25 ms. Document Number: 002-15053 Rev. *D Page 132 of 155 ADVANCE CYW4356 20. Interface Timing and AC Characteristics 20.1 SDIO Timing 20.1.1 SDIO Default Mode Timing SDIO default mode timing is shown by the combination of Figure 38 and Table 52. Figure 38. SDIO Bus Timing (Default Mode) fPP tWL tWH SDIO_CLK tTHL tTLH tISU tIH Input Output Document Number: 002-15053 Rev. *D tODLY tODLY (max) (min) Page 133 of 155 ADVANCE CYW4356 Table 52. SDIO Bus Timinga Parameters (Default Mode) Parameter Symbol Minimum Typical Maximum Unit VILb SDIO CLK (All values are referred to minimum VIH and maximum ) Frequency – Data Transfer mode fPP 0 – 25 MHz Frequency – Identification mode fOD 0 – 400 kHz Clock low time tWL 10 – – ns Clock high time tWH 10 – – ns Clock rise time tTLH – – 10 ns Clock low time tTHL – – 10 ns Inputs: CMD, DAT (referenced to CLK) Input setup time tISU 5 – – ns Input hold time tIH 5 – – ns Output delay time – Data Transfer mode tODLY 0 – 14 ns Output delay time – Identification mode tODLY 0 – 50 ns Outputs: CMD, DAT (referenced to CLK) a. Timing is based on CL ≤ 40pF load on CMD and Data. b. Min. (Vih) = 0.7 × VDDIO and max. (Vil) = 0.2 × VDDIO. 20.1.2 SDIO High-Speed Mode Timing SDIO high-speed mode timing is shown by the combination of Figure 39 and Table 53. Figure 39. SDIO Bus Timing (High-Speed Mode) fPP tWL tWH 50% VDD SDIO_CLK tTHL tISU tTLH tIH Input Output tODLY Document Number: 002-15053 Rev. *D tOH Page 134 of 155 ADVANCE CYW4356 Table 53. SDIO Bus Timinga Parameters (High-Speed Mode) Parameter Symbol SDIO CLK (all values are referred to minimum VIH and maximum Minimum Typical Maximum Unit VILb ) Frequency – Data Transfer Mode fPP 0 – 50 MHz Frequency – Identification Mode fOD 0 – 400 kHz Clock low time tWL 7 – – ns Clock high time tWH 7 – – ns Clock rise time tTLH – – 3 ns Clock low time tTHL – – 3 ns Inputs: CMD, DAT (referenced to CLK) Input setup Time tISU 6 – – ns Input hold Time tIH 2 – – ns tODLY – – 14 ns Outputs: CMD, DAT (referenced to CLK) Output delay time – Data Transfer Mode Output hold time tOH 2.5 – – ns Total system capacitance (each line) CL – – 40 pF a. Timing is based on CL ≤ 40pF load on CMD and Data. b. Min. (Vih) = 0.7 × VDDIO and max. (Vil) = 0.2 × VDDIO. 20.1.3 SDIO Bus Timing Specifications in SDR Modes Clock Timing Figure 40. SDIO Clock Timing (SDR Modes) tCLK SDIO_CLK tCR tCF tCR Table 54. SDIO Bus Clock Timing Parameters (SDR Modes) Parameter – Symbol tCLK Minimum Maximum Unit Comments 40 – ns SDR12 mode 20 – ns SDR25 mode 10 – ns SDR50 mode 4.8 – ns SDR104 mode – tCR, tCF – 0.2 × tCLK ns tCR, tCF < 2.00 ns (max.) @100 MHz, CCARD = 10 pF tCR, tCF < 0.96 ns (max.) @208 MHz, CCARD = 10 pF Clock duty – 30 70 % – Document Number: 002-15053 Rev. *D Page 135 of 155 ADVANCE CYW4356 Device Input Timing Figure 41. SDIO Bus Input Timing (SDR Modes) SDIO_CLK tIS tIH CMD input DAT[3:0] input Table 55. SDIO Bus Input Timing Parameters (SDR Modes) Symbol Minimum Maximum Unit Comments SDR104 Mode tIS 1.4 – ns CCARD = 10 pF, VCT = 0.975V tIH 0.80 – ns CCARD = 5 pF, VCT = 0.975V SDR50 Mode tIS 3.00 – ns CCARD = 10 pF, VCT = 0.975V tIH 0.80 – ns CCARD = 5 pF, VCT = 0.975V Document Number: 002-15053 Rev. *D Page 136 of 155 ADVANCE CYW4356 Device Output Timing Figure 42. SDIO Bus Output Timing (SDR Modes up to 100 MHz) tCLK SDIO_CLK tODLY tOH CMD input DAT[3:0] input Table 56. SDIO Bus Output Timing Parameters (SDR Modes up to 100 MHz) Symbol Minimum Maximum Unit Comments tODLY – 7.5 ns tCLK ≥ 10 ns CL= 30 pF using driver type B for SDR50 tODLY – 14.0 ns tCLK ≥ 20 ns CL= 40 pF using for SDR12, SDR25 tOH 1.5 – ns Hold time at the tODLY (min.) CL= 15 pF Document Number: 002-15053 Rev. *D Page 137 of 155 ADVANCE CYW4356 Figure 43. SDIO Bus Output Timing (SDR Modes 100 MHz to 208 MHz) tCLK SDIO_CLK tOP tODW CMD input DAT[3:0] input Table 57. SDIO Bus Output Timing Parameters (SDR Modes 100 MHz to 208 MHz) Symbol Minimum Maximum Unit Comments tOP 0 ∆tOP –350 +1550 ps Delay variation due to temp change after tuning tODW 0.60 – UI tODW=2.88 ns @208 MHz 2 UI Card output phase ■ ∆tOP = +1550 ps for junction temperature of ∆tOP = 90 degrees during operation ■ ∆tOP = –350 ps for junction temperature of ∆tOP = –20 degrees during operation ■ ∆tOP = +2600 ps for junction temperature of ∆tOP = –20 to +125 degrees during operation Document Number: 002-15053 Rev. *D Page 138 of 155 ADVANCE CYW4356 Figure 44. ∆tOP Consideration for Variable Data Window (SDR 104 Mode) Data valid window Sampling point after tuning ȴtOP = 1550 ps ȴtOP = –350 ps Data valid window Sampling point after card junction heating by +90°C from tuning temperature Data valid window Sampling point after card junction cooling by –20°C from tuning temperature 20.1.4 SDIO Bus Timing Specifications in DDR50 Mode Figure 45. SDIO Clock Timing (DDR50 Mode) tCLK SDIO_CLK tCR tCF tCR Table 58. SDIO Bus Clock Timing Parameters (DDR50 Mode) Parameter Symbol Minimum Maximum Unit Comments – tCLK 20 – ns DDR50 mode – tCR,tCF – 0.2 × tCLK ns tCR, tCF < 4.00 ns (max.) @50 MHz, CCARD = 10 pF Clock duty – 45 55 % – Document Number: 002-15053 Rev. *D Page 139 of 155 ADVANCE CYW4356 Data Timing, DDR50 Mode Figure 46. SDIO Data Timing (DDR50 Mode) FPP SDIO_CLK tISU2x DAT[3:0] input Invalid tIH2x Data tISU2x Invalid tIH2x Data Invalid tODLY2x (max) DAT[3:0] output Data Invalid tODLY2x (max) tODLY2x tODLY2x (min) (min) Data Available timing window for card output transition Data In DDR50 mode, DAT[3:0] lines are sampled on both edges of the clock (not applicable for CMD line) Data Available timing window for host to sample data from card Table 59. SDIO Bus Timing Parameters (DDR50 Mode) Parameter Symbol Minimum Maximum Unit Comments Input CMD Input setup time tISU 6 – ns CCARD < 10pF (1 Card) Input hold time tIH 0.8 – ns CCARD < 10pF (1 Card) Output delay time tODLY – 13.7 ns CCARD < 30pF (1 Card) Output hold time tOH 1.5 – ns CCARD < 15pF (1 Card) Output CMD Input DAT Input setup time tISU2x 3 – ns CCARD < 10pF (1 Card) Input hold time tIH2x 0.8 – ns CCARD < 10pF (1 Card) Output delay time tODLY2x – 7.5 ns CCARD < 25pF (1 Card) Output hold time tODLY2x 1.5 – ns CCARD < 15pF (1 Card) Output DAT Document Number: 002-15053 Rev. *D Page 140 of 155 ADVANCE CYW4356 20.2 PCI Express Interface Parameters Table 60. PCI Express Interface Parameters Parameter Symbol Comments Minimum Typical Maximum Unit Generala Baud rate BPS Reference clock peak-to- Vref peak differential amplitudeb – – 5 – Gbaud LVPECL 0.95 – – V Receiver Differential termination ZRX-DIFF-DC Differential termination 80 100 120 Ω DC impedance ZRX-DC DC common-mode impedance 40 50 60 Ω Powered down termination (POS) ZRX-HIGH-IMP-DCPOS Power-down or RESET high impedance 100k – – Ω Powered down termination (NEG) ZRX-HIGH-IMP-DCNEG Power-down or RESET high impedance 1k – – Ω Input voltage VRX-DIFFp-p AC coupled, differential p-p 175 – – mV Jitter tolerance TRX-EYE Minimum receiver eye width 0.4 – – UI Differential return loss RLRX-DIFF Differential return loss 10 – – dB Common-mode return loss RLRX-CM Common-mode return loss 6 – – dB An unexpected electrical – idle must be recognized no longer than this time to signal an unexpected idle condition. – 10 ms 65 – 175 mV Unexpected electrical TRX-IDEL-DET-DIFFidle enter detect threshold ENTERTIME integration time Signal detect threshold VRX-IDLE-DET-DIFFp-p Electrical idle detect threshold Transmitter Output voltage VTX-DIFFp-p Differential p-p, program- 0.8 mable in 16 steps – 1200 mV Output voltage rise time VTX-RISE 20% to 80% 0.125 (2.5 GT/s) 0.15 (5 GT/s) – – UI Output voltage fall time VTX-FALL 80% to 20% 0.125 (2.5 GT/s) 0.15 (5 GT/s) – – UI RX detection voltage swing VTX-RCV-DETECT The amount of voltage change allowed during receiver detection. – – 600 mV TX AC peak commonmode voltage (5 GT/s) VTX-CM-AC-PP TX AC common mode voltage (5 GT/s) – – 100 mV TX AC peak commonmode voltage (2.5 GT/s) VTX-CM-AC-P TX AC common mode voltage (2.5 GT/s) – – 20 mV Document Number: 002-15053 Rev. *D Page 141 of 155 ADVANCE CYW4356 Table 60. PCI Express Interface Parameters (Cont.) Parameter Symbol Comments Minimum Typical Maximum Unit Absolute delta of DC common-model voltage during L0 and electrical idle VTX-CM-DC-ACTIVEIDLE-DELTA Absolute delta of DC common-model voltage during L0 and electrical idle. 0 – 100 mV Absolute delta of DC common-model voltage between D+ and D- VTX-CM-DC-LINEDELTA DC offset between D+ and D- 0 – 25 mV Electrical idle differential VTX-IDLE-DIFF-AC-p peak output voltage Peak-to-peak voltage 0 – 20 mV TX short circuit current Current limit when TX output is shorted to ground. – – 90 mA – 120 Ω ITX-SHORT DC differential TX termi- ZTX-DIFF-DC nation Low impedance defined 80 during signaling (parameter is captured for 5.0 GHz by RLTX-DIFF) Differential return loss RLTX-DIFF Differential return loss 10 (min.) for – 0.05: 1.25 GHz – dB Common-mode return loss RLTX-CM Common-mode return loss 6 – – dB TX eye width TTX-EYE Minimum TX eye width 0.75 – – UI a. For out-of-band PCIe signal specifications, refer to Table 33. b. The reference clock inputs comply with the requirements of the PCI Express CEM v2.0 Specification (see References). 20.3 JTAG Timing Table 61. JTAG Timing Characteristics Signal Name Output Maximum Period Output Minimum Setup Hold TCK 125 ns – – – – TDI – – – 20 ns 0 ns TMS – – – 20 ns 0 ns TDO – 100 ns 0 ns – – JTAG_TRST 250 ns – – – – Document Number: 002-15053 Rev. *D Page 142 of 155 ADVANCE CYW4356 21. Power-Up Sequence and Timing 21.1 Sequencing of Reset and Regulator Control Signals The CYW4356 has two signals that allow the host to control power consumption by enabling or disabling the Bluetooth, WLAN, and internal regulator blocks. These signals are described below. Additionally, diagrams are provided to indicate proper sequencing of the signals for various operational states (see Figure 47, Figure 48, and Figure 49 and Figure 50). The timing values indicated are minimum required values; longer delays are also acceptable. 21.1.1 Description of Control Signals ■ WL_REG_ON: Used by the PMU to power up the WLAN section. It is also OR-gated with the BT_REG_ON input to control the internal CYW4356 regulators. When this pin is high, the regulators are enabled and the WLAN section is out of reset. When this pin is low the WLAN section is in reset. If both the BT_REG_ON and WL_REG_ON pins are low, the regulators are disabled. ■ BT_REG_ON: Used by the PMU (OR-gated with WL_REG_ON) to power up the internal CYW4356 regulators. If both the BT_REG_ON and WL_REG_ON pins are low, the regulators are disabled. When this pin is low and WL_REG_ON is high, the BT section is in reset. Note: ■ For both the WL_REG_ON and BT_REG_ON pins, there should be at least a 10 ms time delay between consecutive toggles (where both signals have been driven low). This is to allow time for the CBUCK regulator to discharge. If this delay is not followed, then there may be a VDDIO in-rush current on the order of 36 mA during the next PMU cold start. ■ The reset requirements for the Bluetooth core are also applicable for the FM core. In other words, if FM is to be used, then the Bluetooth core must be enabled. ■ The CYW4356 has an internal power-on reset (POR) circuit. The device will be held in reset for a maximum of 110 ms after VDDC and VDDIO have both passed the POR threshold. Wait at least 150 ms after VDDC and VDDIO are available before initiating SDIO accesses. ■ VBAT should not rise 10%–90% faster than 40 microseconds. VBAT should be up before or at the same time as VDDIO. VDDIO should NOT be present first or be held high before VBAT is high. 21.1.2 Control Signal Timing Diagrams Figure 47. WLAN = ON, Bluetooth = ON 32.678 kHz Sleep Clock VBAT* 90% of VH VDDIO ~ 2 Sleep cycles WL_REG_ON BT_REG_ON *Notes: 1. VBAT should not rise 10%–90% faster than 40 microseconds. 2. VBAT should be up before or at the same time as VDDIO. VDDIO should NOT be present first or be held high before VBAT is high. Document Number: 002-15053 Rev. *D Page 143 of 155 ADVANCE CYW4356 Figure 48. WLAN = OFF, Bluetooth = OFF 32.678 kHz Sleep Clock VBAT* VDDIO WL_REG_ON BT_REG_ON *Notes: 1. VBAT should not rise 10%–90% faster than 40 microseconds. 2. VBAT should be up before or at the same time as VDDIO. VDDIO should NOT be present first or be held high before VBAT is high. Figure 49. WLAN = ON, Bluetooth = OFF 32.678 kHz Sleep Clock VBAT* 90% of VH VDDIO ~ 2 Sleep cycles WL_REG_ON BT_REG_ON *Notes: 1. VBAT should not rise 10%–90% faster than 40 microseconds. 2. VBAT should be up before or at the same time as VDDIO. VDDIO should NOT be present first or be held high before VBAT is high. Document Number: 002-15053 Rev. *D Page 144 of 155 ADVANCE CYW4356 Figure 50. WLAN = OFF, Bluetooth = ON 32.678 kHz Sleep Clock VBAT* 90% of VH VDDIO ~ 2 Sleep cycles WL_REG_ON BT_REG_ON *Notes: 1. VBAT should not rise 10%–90% faster than 40 microseconds. 2. VBAT should be up before or at the same time as VDDIO. VDDIO should NOT be present first or be held high before VBAT is high . Document Number: 002-15053 Rev. *D Page 145 of 155 ADVANCE CYW4356 21.1.3 Power-up Sequences Figure 51 shows the WLAN boot-up sequence from power-up to firmware download. Figure 51. WLAN Boot-Up Sequence VBAT* VDDIO WL_REG_ON < 950 µs VDDC (from internal PMU) < 104 ms Internal POR < 4 ms After a fixed delay following Internal POR and WL_REG_ON going high, the device responds to host F0 (address 0x14) reads. Device requests for reference clock 8 ms After 8 ms the reference clock is assumed to be up. Access to PLL registers is possible. Host Interaction: Host polls F0 (address 0x14) until it reads a predefined pattern. Host sets wake‐up‐wlan bit and waits 8 ms, the maximum time for reference clock availability. After 8 ms, host programs PLL registers to set crystal frequency Chip active interrupt is asserted after the PLL locks Host downloads code. *Notes: 1. VBAT should not rise 10%–90% faster than 40 microseconds. 2. VBAT should be up before or at the same time as VDDIO. VDDIO should NOT be present first or be held high before VBAT is high. Document Number: 002-15053 Rev. *D Page 146 of 155 ADVANCE CYW4356 Figure 52 and Table 62 show the WLAN/PCIe power-up timing. Figure 52. WLAN/PCIe Power-Up Timing VBAT VDDIO Tvbattoregon WL_REG_ON BT_REG_ON TRegontovdd VDDC Tregontopor Tvddtopor WL_Internal_POR_L PCIE_CLKREQ_L Trefclkstable Trefclkstable PCIE_REFCLK Tref2perst Tref2perst PCIE_PERST_L Tperst2firstconfig Tperst2firstconfig First Config. Access Tvregontofirstconfig Table 62. Timing Parameters WL_REG_ON to Perst# Deassertion to FirstConfigAccess Timing Parameter Typical Value Maximum Value TVbattoregon 100 μs – Tregontovdd (1.2V) 1 ms – Tvddtopor 57 ms – Trefclkstable 10 ms – Tref2perst 100 μs – Tperst2firstconfig 6 ms – Tvregontofirstconfig – 100 ms Document Number: 002-15053 Rev. *D Page 147 of 155 ADVANCE CYW4356 22. Package Information 22.1 Package Thermal Characteristics The information in Table 63 and Table 64 is based on the following conditions: ■ No heat sink, TA = 70°C. This is an estimate, based on a 4-layer PCB that conforms to EIA/JESD51–7 (101.6 mm × 101.6 mm × 1.6 mm) and P = 1.53W continuous dissipation. ■ Absolute junction temperature limits are maintained through active thermal monitoring and driver-based techniques that may include duty-cycle limiting or turning off one of the TX chains, or both. Table 63. WLCSP Package Thermal Characteristics Characteristic WLCSP JA (°C/W) (value in still air) 26.86 JB (°C/W) 2.23 JC (°C/W) 1.09 JT (°C/W) JB (°C/W) 2.48 11.61 Maximum Junction Temperature Tj (°C) 125 Maximum Power Dissipation (W) 1.53 Table 64. WLBGA Package Thermal Characteristics Characteristic WLBGA JA (°C/W) (value in still air) JB (°C/W) JC (°C/W) 26.80 JT (°C/W) JB (°C/W) 1.85 Maximum Junction Temperature Tj (°C) 125 Maximum Power Dissipation (W) 1.53 1.66 1.16 7.93 22.2 Junction Temperature Estimation and PSIJT Versus ThetaJC The package thermal characterization parameter PSIJT (JT) yields a better estimation of actual junction temperature (TJ) than using the junction-to-case thermal resistance parameter ThetaJC (JC). The reason for this is that JC is based on the assumption that all the power is dissipated through the top surface of the package case. In actual applications, however, some of the power is dissipated through the bottom and sides of the package. JT takes into account the power dissipated through the top, bottom, and sides of the package. The equation for calculating the device junction temperature is: TJ = TT + P x JT Where: ■ TJ = Junction temperature at steady-state condition (°C) ■ TT = Package case top center temperature at steady-state condition (°C) ■ P = Device power dissipation (Watts) ■ JT = Package thermal characteristics; no airflow (°C/W) 22.3 Environmental Characteristics For environmental characteristics data, see Table 31. Document Number: 002-15053 Rev. *D Page 148 of 155 ADVANCE CYW4356 23. Mechanical Information Figure 53. 192-Ball WLBGA Package Mechanical Information Document Number: 002-15053 Rev. *D Page 149 of 155 ADVANCE CYW4356 Figure 54. WLBGA Keep-Out Areas for PCB Layout (Top View, Balls Facing Down) Document Number: 002-15053 Rev. *D Page 150 of 155 ADVANCE CYW4356 Figure 55. 395-Bump WLCSP Package Document Number: 002-15053 Rev. *D Page 151 of 155 ADVANCE CYW4356 Figure 56. WLCSP Keep-Out Areas for PCB Layout (Top View, Balls Facing Down) Document Number: 002-15053 Rev. *D Page 152 of 155 ADVANCE CYW4356 24. Ordering Information Part Number Package Description Operating Ambient Temperature BCM4356XKUBG 192-ball WLBGA (4.87 mm × 7.67 mm, 0.4 mm pitch) Dual-band 2.4 GHz and 5 GHz WLAN + BT 4.1 –30°C to +85°C + FMRX + A4WP (–22°F to 185°F) BCM4356XKWBG 395-bump WLCSP (4.87 mm × 7.67 mm, 0.2 mm pitch) Dual-band 2.4 GHz and 5 GHz WLAN + BT 4.1 –30°C to +85°C + FMRX + A4WP (–22°F to 185°F) 25. Additional Information 25.1 Acronyms and Abbreviations In most cases, acronyms and abbreviations are defined on first use. For a comprehensive list of acronyms and other terms used in Cypress documents, go to: http://www.cypress.com/glossary 25.2 References The references in this section may be used in conjunction with this document. Note: Cypress provides customer access to technical documentation and software through its Cypress Developer Community and Downloads and Support site (see IoT Resources). For Cypress documents, replace the “xx” in the document number with the largest number available in the repository to ensure that you have the most current version of the document. Document (or Item) Name Bluetooth MWS Coexistence 2–wire Transport Interface Specification Number – Source www.bluetooth.com A4WP Wireless Power Transfer System Baseline System Specification – (BSS) January 2, 2013 www.a4wp.org PCI Express CEM v2.0 Specification www.pcisig.com – 26. IoT Resources Cypress provides a wealth of data at http://www.cypress.com/internet-things-iot to help you to select the right IoT device for your design, and quickly and effectively integrate the device into your design. Cypress provides customer access to a wide range of information, including technical documentation, schematic diagrams, product bill of materials, PCB layout information, and software updates. Customers can acquire technical documentation and software from the Cypress Support Community website (http://community.cypress.com/). Document Number: 002-15053 Rev. *D Page 153 of 155 ADVANCE CYW4356 Document History Document Title: CYW4356 Single-Chip 5G WiFi IEEE 802.11ac 2×2 MAC/Baseband/Radio with Integrated Bluetooth 4.1, FM Receiver, and Wireless Charging Document Number: 002-15053 Revision ECN Orig. of Change Submission Date ** – – 04/01/2014 4356-DS100-R Initial release *A – – 04/24/2014 4356-DS101-R • Refer to the released document for earlier revision history. *B – – 06/25/2014 4356-DS102-R Updated: • Pin name PCI_PME_L to PCIE_PME_L. • “BCM4356 PMU Features”. • Table 59: “PCI Express Interface Parameters” Added: • “Electrostatic Discharge Specifications”. *C – – 05/08/2015 4356-DS103-R Updated: • From Advance to Preliminary Datasheet. • Features • Power-Off Shutdown • Table 5. External 32.768 kHz Sleep Clock Specifications. • Table 22. WLCSP Signal Descriptions. • Table 23. WLBGA Signal Descriptions. • Table 27. GPIO Alternative Signal Functions. • Table 33. Recommended Operating Conditions and DC Characteristics. • Table 40. WLAN 2.4 GHz Receiver Performance Specifications. • Table 41. WLAN 2.4 GHz Transmitter Performance Specifications. • Table 42. WLAN 5 GHz Receiver Performance Specifications. • Table 43. WLAN 5 GHz Transmitter Performance Specifications. • Table 50. Typical WLAN Power Consumption. • Table 60. PCI Express Interface Parameters. • Figure 54. WLBGA Keep-Out Areas for PCB Layout (Top View, Balls Facing Down). Added: • Figure 52. WLAN/PCIe Power-Up Timing. • Table 62. Timing Parameters WL_REG_ON to Perst# Deassertion to FirstConfigAccess. Removed: • Note removed from the data sheet “Values in this data sheet are design goals and are subject to change based on the results of device characterization.” *D 5491748 UTSV 11/14/2016 Updated to Cypress Template. Added Cypress Part Numbering Scheme. Document Number: 002-15053 Rev. *D Description of Change Page 154 of 155 ADVANCE CYW4356 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC®Solutions Products ARM® Cortex® Microcontrollers Automotive cypress.com/arm cypress.com/automotive Clocks & Buffers Interface cypress.com/clocks cypress.com/interface Internet of Things Lighting & Power Control Memory cypress.com/iot cypress.com/powerpsoc cypress.com/memory PSoC Cypress Developer Community Forums | WICED IoT Forums | Projects | Video | Blogs | Training | Components Technical Support cypress.com/support cypress.com/psoc Touch Sensing cypress.com/touch USB Controllers Wireless/RF PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP cypress.com/usb cypress.com/wireless 155 © Cypress Semiconductor Corporation, 2014-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC (“Cypress”). This document, including any software or firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage (“Unintended Uses”). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. Document Number: 002-15053 Rev. *D Revised November 14, 2016 Page 155 of 155