TI1 DAC714PG4 16-bit digital-to-analog converter with serial data interface Datasheet

DAC714
DA
C71
4
DAC
714
SBAS032A – JULY 1997 – REVISED NOVEMBER 2005
16-Bit DIGITAL-TO-ANALOG CONVERTER
With Serial Data Interface
FEATURES:
DESCRIPTION
● SERIAL DIGITAL INTERFACE
The DAC714 is a complete monolithic digital-toanalog (D/A) converter including a +10V temperature compensated reference, current-to-voltage amplifier, a high-speed
synchronous serial interface, a serial output which allows
cascading multiple converters, and an asynchronous clear
function which immediately sets the output voltage to midscale.
● VOLTAGE OUTPUT: ±10V, ±5V, 0 to +10V
● ±1 LSB INTEGRAL LINEARITY
● 16-BIT MONOTONIC OVER TEMPERATURE
● PRECISION INTERNAL REFERENCE
The output voltage range is ±10V, ±5V, or 0 to +10V while
operating from ±12V or ±15V supplies. The gain and bipolar
offset adjustments are designed so that they can be set via
external potentiometers or external D/A converters. The
output amplifier is protected against short circuit to ground.
● LOW NOISE: 120nV/√Hz Including Reference
● 16-LEAD PLASTIC AND CERAMIC SKINNY
DIP AND PLASTIC SO PACKAGES
The 16-pin DAC714 is available in a plastic 0.3" DIP, ceramic
0.3" CERDIP, and wide-body plastic SO package. The
DAC714P, U, HB, and HC are specified over the –40°C to
+85°C temperature range while the DAC714HL is specified
over the 0°C to +70°C range.
A0
Input Shift Register
A1
SDI
SDO
16
RFB2
CLK
D/A Latch
CLR
16
Reference
Circuit
Gain
Adjust
16-Bit D/A Converter
VOUT
VREF OUT
+10V
RBPO
Offset Adjust
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright © 1997-2005, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ABSOLUTE MAXIMUM RATINGS(1)
+VCC to Common .................................................................... 0V to +17V
–VCC to Common .................................................................... 0V to –17V
+VCC to –VCC ....................................................................................... 34V
ACOM to DCOM ............................................................................... ±0.5V
Digital Inputs to Common ............................................. –1V to (VCC –0.7V)
External Voltage Applied to BPO and Range Resistors .................... ±VCC
VREF OUT .......................................................... Indefinite Short to Common
VOUT ............................................................... Indefinite Short to Common
SDO ............................................................... Indefinite Short to Common
Power Dissipation .......................................................................... 750mW
Storage Temperature ...................................................... –60°C to +150°C
Lead Temperature (soldering, 10s) ............................................... +300°C
NOTE: (1) Stresses above those listed under Absolute Maximum Ratings may
cause permanent damage to the device. Exposure to absolute maximum
conditions for extended periods may affect device reliability.
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
For the most current package and ordering information, see
the Package Option Addendum at the end of this document,
or see the TI website at www.ti.com.
PIN CONFIGURATION
PIN DESCRIPTIONS
Top View
SO/DIP
CLK
1
16 CLR
A0
2
15 –VCC
A1
3
14 Gain Adjust
SDI
4
13 Offset Adjust
DAC714
2
SDO
5
12 VREF OUT
DCOM
6
11 RBPO
+VCC
7
10 RFB2
ACOM
8
9
VOUT
PIN
LABEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CLK
A0
A1
SDI
SDO
DCOM
+VCC
ACOM
VOUT
RFB2
RBPO
VREF OUT
Offset Adjust
Gain Adjust
–VCC
CLR
DESCRIPTION
Serial Data Clock
Enable for Input Register (Active Low)
Enable for D/A Latch (Active Low)
Serial Data Input
Serial Data Output
Digital Ground
Positive Power Supply
Analog Ground
D/A Output
±10V Range Feedback Output
Bipolar Offset
Voltage Reference Output
Offset Adjust
Gain Adjust
Negative Power Supply
Clear
DAC714
www.ti.com
SBAS032A
ELECTRICAL CHARACTERISTICS
At TA = +25°C, +VCC = +12V and +15V, –VCC = –12V, and –15V, unless otherwise noted.
DAC714P, U
PARAMETER
MIN
TYP
DAC714HB
MAX
MIN
TYP
DAC714HC
MAX
MIN
TYP
DAC714HL
MAX
MIN
TYP
MAX
UNITS
±1
±2
±1
±1
LSB
LSB
LSB
LSB
Bits
Bits
%
%
% of FSR(2)
% of FSR
%FSR/%VCC
ppm FSR/%VCC
TRANSFER CHARACTERISTICS
ACCURACY
Linearity Error
TMIN to TMAX
Differential Linearity Error
TMIN to TMAX
Monotonicity
Monotonicity Over Spec Temp Range
Gain Error(3)
TMIN to TMAX
Unipolar/Bipolar Zero Error(3)
TMIN to TMAX
Power Supply Sensitivity of Gain
±4
±8
±4
±8
14
13
REFERENCE VOLTAGE
Voltage
TMIN to TMAX
Output Resistance
Source Current
Short Circuit to ACOM Duration
15
14
6
4
10
10
6
4
10
±0.1
±0.25
±0.1
±0.2
±0.003
±30
10
6
4
10
0.005
0.03
3.0
87
2
15
120
±10
±5
0.1
Indefinite
+9.975
+9.960
1
6
4
10
+10.000
0.005
0.03
3.0
87
2
15
120
0.1
Indefinite
+10.025
+10.040
2
10
+9.975
+9.960
V
mA
Ω
0.1
Indefinite
+10.000 +10.025
+10.040
1
2
+9.975
+9.960
+10.000 +10.025
+10.040
1
2
Indefinite
Indefinite
Indefinite
Indefinite
16
16
16
16
µs
µs
V/µs
%
%
%
dB
nV–s
nV–s
nV/√Hz
±10
±5
1
2
10
±10
±5
0.1
Indefinite
+10.025
+10.040
±0.1
±0.25
±0.1
±0.2
±0.003
±30
0.005
0.03
3.0
87
2
15
120
±10
±5
+10.000
16
16
±0.1
±0.25
±0.1
±0.2
±0.003
±30
0.005
0.03
3.0
87
2
15
120
+9.975
+9.960
±1
±2
±1
±2
16
15
±0.1
±0.25
±0.1
±0.2
±0.003
±30
DYNAMIC PERFORMANCE
Settling Time
(to ±0.003%FSR, 5kΩ || 500pF Load)(4)
20V Output Step
1LSB Output Step(5)
Output Slew Rate
Total Harmonic Distortion
0dB, 1001Hz, fS = 100kHz
–20dB, 1001Hz, fS = 100kHz
–60dB, 1001Hz, fS = 100kHz
SINAD: 1001Hz, fS = 100kHz
Digital Feedthrough(5)
Digital-to-Analog Glitch Impulse(5)
Output Noise Voltage (includes reference)
ANALOG OUTPUT
Output Voltage Range
+VCC, –VCC = ±11.4V
Output Current
Output Impedance
Short Circuit to ACOM Duration
±2
±4
±2
±4
V
V
Ω
mA
INTERFACE
RESOLUTION
DIGITAL INPUTS
Serial Data Input Code
Logic Levels(1)
VIH
VIL
+2.0
(VCC –1.4)
+2.0
0
+0.8
0
Binary Two’s Complement
(VCC –1.4) +2.0
+0.8
0
Bits
(VCC –1.4)
+2.0
(VCC –1.4)
+0.8
0
+0.8
V
V
IIH (VI = +2.7V)
±10
±10
±10
±10
µA
IIL (VI = +0.4V)
±10
±10
±10
±10
µA
+0.4
+5
V
V
+15
–15
+16.5
–16.5
V
V
13
22
16
26
625
mA
mA
mW
+70
+150
°C
°C
°C/W
DIGITAL OUTPUT
Serial Data
VOL (ISINK = 1.6mA)
VOH (ISOURCE = 500µA), TMIN to TMAX
POWER SUPPLY REQUIREMENTS
Voltage
+VCC
–VCC
Current (No Load, ±15V Supplies)(6)
+VCC
–VCC
Power Dissipation(7)
TEMPERATURE RANGES
Specification
All Grades
Storage
Thermal Coefficient, θJA
0
+2.4
+11.4
–11.4
+0.4
+5
0
+2.4
+15
–15
+16.5
–16.5
+11.4
–11.4
13
22
16
26
625
–40
–60
+85
+150
75
+0.4
+5
0
+2.4
+15
–15
+16.5
–16.5
+11.4
–11.4
13
22
16
26
625
–40
–60
+85
+150
75
+0.4
+5
0
+2.4
+15
–15
+16.5
–16.5
+11.4
–11.4
13
22
16
26
625
–40
–60
+85
+150
75
0
–60
75
NOTES: (1) Digital inputs are TTL and +5V CMOS compatible over the specification temperature range. (2) FSR means Full Scale Range. For example, for ±10V output, FSR = 20V. (3) Errors
externally adjustable to zero. (4) Maximum represents the 3σ limit. Not 100% tested for this parameter. (5) For the worst-case Binary Two’s Complement code changes: FFFF H to 0000H and 0000H
to FFFFH. (6) During power supply turn on, the transient supply current may approach 3x the maximum quiescent specification. (7) Typical (i.e. rated) supply voltages times maximum currents.
DAC714
SBAS032A
www.ti.com
3
TIMING SPECIFICATIONS
TRUTH TABLE
TA = –40°C to +85°C, +VCC = +12V or +15V, –VCC = –12V or –15V.
SYMBOL
PARAMETER
MIN
tCLK
tCL
tCH
tA0S
tA1S
tAOH
tA1H
tDS
tDH
tDSOP
tCP
Data Clock Period
Clock LOW
Clock HIGH
Setup Time for A0
Setup Time for A1
Hold Time for A0
Hold Time for A1
Setup Time for DATA
Hold Time for DATA
Output Propagation Delay
Clear Pulsewidth
100
50
50
50
50
0
0
50
10
MAX
UNITS
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
140
200
A0
A1
CLK
CLR
DESCRIPTION
0
1
1
0
1→0→1
1
Shift Serial Data into SDI
1→0→1
1
1
Load D/A Latch
1
1→0→1
1
No Change
0
0
1→0→1
1
Two Wire Operation(1)
X
X
1
1
No Change
X
X
X
0
Reset D/A Latch
NOTES: X = Don’t Care. (1) All digital input changes will appear at the
output.
TIMING DIAGRAMS
Serial Data In
tCLK
tCH
tCL
CLK
tA
0H
tA
0S
A0
tDS
Serial Data Input
MSB First
tDH
D15
SDI
D14
D0
tA
1S
Latch Data
In D/A Latch
tA
1H
A1
Serial Data Out
tCLK
tCH
tCL
CLK
tA
tA
0S
0H
A0
Serial Data
Out
D15
SDO
D14
D0
tDSOP
tDSOP
Clear
tCP
CLR
4
DAC714
www.ti.com
SBAS032A
TYPICAL CHARACTERISTICS
POWER SUPPLY REJECTION vs
POWER SUPPLY RIPPLE FREQUENCY
LOGIC vs V LEVEL
1k
2.0
–VCC
100
I Digital Input (µA)
[Change in FSR] / [Change in Supply Voltage]
(ppm of FSR/ %)
At TA = +25°C, VCC = ±15V, unless otherwise noted.
+VCC
10
1
100
1k
10k
100k
A0, A1
CLR
0
SDI
–1.0
–2.0
–0.85
0.1
10
1.0
1M
0
0.85 1.7 2.55
3.4 4.25
5.1 5.95
6.8
V Digital Input
Frequency (Hz)
SETTLING TIME, +10V TO –10V
± FULL SCALE OUTPUT SWING
∆ Around –10V (µV)
VOUT (V)
10
0
2000
+5V
1500
0V
A1 (V)
2500
1000
500
0
–500
–1000
–1500
–2000
–10
–2500
Time (1µs/div)
Time (10µs/div)
VOUT SPECTRAL NOISE DENSITY
SETTLING TIME, –10V TO +10V
1000
+5V
1500
0V
A1
2000
1000
100
nV/√Hz
∆ Around +10V (µV)
2500
500
0
–500
10
–1000
–1500
–2000
1
–2500
1
Time (1µs/div)
10
100
1k
10k
100k
1M
10M
Frequency (Hz)
DAC714
SBAS032A
www.ti.com
5
DISCUSSION OF
SPECIFICATIONS
LINEARITY ERROR
Linearity error is defined as the deviation of the analog
output from a straight line drawn between the end points of
the transfer characteristic.
DIFFERENTIAL LINEARITY ERROR
Differential linearity error (DLE) is the deviation from
1LSB of an output change from one adjacent state to the
next. A DLE specification of ±1/2LSB means that the output
step size can range from 1/2LSB to 3/2LSB when the digital
input code changes from one code word to the adjacent code
word. If the DLE is more positive than –1LSB, the D/A is
said to be monotonic.
MONOTONICITY
A D/A converter is monotonic if the output either increases
or remains the same for increasing digital input values.
Monotonicity of the C and L grades is assured over the
specification temperature range to 16 bits.
SETTLING TIME
Settling time is the total time (including slew time) for the
D/A output to settle to within an error band around its final
value after a change in input. Settling times are specified to
within ±0.003% of Full Scale Range (FSR) for an output
step change of 20V and 1LSB. The 1LSB change is measured at the Major Carry (FFFFH to 0000H, and 0000H to
FFFFH: BTC codes), the input transition at which worst-case
settling time occurs.
TOTAL HARMONIC DISTORTION
Total harmonic distortion is defined as the ratio of the
square root of the sum of the squares of the values of the
harmonics to the value of the fundamental frequency. It is
expressed in % of the fundamental frequency amplitude at
sampling rate fS.
SIGNAL-TO-NOISE
AND DISTORTION RATIO (SINAD)
SINAD includes all the harmonic and outstanding spurious
components in the definition of output noise power in
addition to quantizing and internal random noise power.
SINAD is expressed in dB at a specified input frequency and
sampling rate, fS.
DIGITAL-TO-ANALOG GLITCH IMPULSE
The amount of charge injected into the analog output from
the digital inputs when the inputs change state. It is measured at half scale at the input codes where as many as
possible switches change state—from 0000H to FFFFH.
6
DIGITAL FEEDTHROUGH
When the A/D is not selected, high frequency logic activity
on the digital inputs is coupled through the device and shows
up as output noise. This noise is digital feedthrough.
OPERATION
The DAC714 is a monolithic integrated-circuit 16-bit D/A
converter complete with 16-bit D/A switches and ladder
network, voltage reference, output amplifier and a serial
interface.
INTERFACE LOGIC
The DAC714 has double-buffered data latches. The input
data latch holds a 16-bit data word before loading it into the
second latch, the D/A latch. This double-buffered organization permits simultaneous update of several D/A converters.
All digital control inputs are active low. Refer to the block
diagram shown in Figure 1.
All latches are level-triggered. Data present when the enable
inputs are logic “0” will enter the latch. When the enable
inputs return to logic “1”, the data is latched.
The CLR input resets both the input latch and the D/A latch
to 0000H (midscale).
LOGIC INPUT COMPATIBILITY
The DAC714 digital inputs are TTL compatible (1.4V switching level), low leakage, and high impedance. Thus, the
inputs are suitable for being driven by any type of 5V logic
family, such as CMOS. An equivalent circuit for the digital
inputs is shown in Figure 2.
The inputs will float to logic “0” if left unconnected. It is
recommended that any unused inputs be connected to DCOM
to improve noise immunity.
Digital inputs remain high impedance when power is off.
INPUT CODING
The DAC714 is designed to accept binary two’s complement (BTC) input codes with the MSB first which are
compatible with bipolar analog output operation. For this
configuration, a digital input of 7FFFH produces a plus full
scale output, 8000H produces a minus full scale output, and
0000H produces bipolar zero output.
INTERNAL REFERENCE
The DAC714 contains a +10V reference. The reference
output may be used to drive external loads, sourcing up to
2mA. The load current should be constant; otherwise, the
gain and bipolar offset of the converter will vary.
DAC714
www.ti.com
SBAS032A
Gain Adjust
VREF OUT
+VCC
– VCC
14
12
7
15
180Ω
15kΩ
+10V
Reference
10
RFB2
11
RBPO
13
Offset
Adjust
9
VOUT
250Ω
10kΩ
+2.5V
9750Ω
10kΩ
–VCC
D/A Switches
CLK
1
A1
3
CLR
16
A0
2
SDI
4
SDO
5
DAC Latch
16
Shift Register
8
6
ACOM
DCOM
FIGURE 1. DAC714 Block Diagram.
+VCC
ESD Protection Circuit
Range of
Gain Adjust
≈ ±0.3%
+ Full Scale
6.8V
Analog Output
1kΩ
Digital
Input
5pF
–VCC
FIGURE 2. Equivalent Circuit of Digital Inputs.
OUTPUT VOLTAGE SWING
The output amplifier of the DAC714 is designed to achieve
a ±10V output range while operating on ±11.4V or higher
power supplies.
All Bits
Logic 0
Range of
Offset Adjust
Offset Adj.
Translates
the Line
≈ ±0.3%
Full Scale
Range
Bipolar
Offset
Gain Adjust
Rotates the Line
MSB on All
Others Off
All Bits
Logic 1
– Full Scale
Digital Input
FIGURE 3. Relationship of Offset and Gain Adjustments.
GAIN AND OFFSET ADJUSTMENTS
Figure 3 illustrates the relationship of offset and gain adjustments for a bipolar connected D/A converter. Offset should
be adjusted first to avoid interaction of adjustments. See
Table I for calibration values and codes. These adjustments
have a minimum range of ±0.3%.
Offset Adjustment
Apply the digital input code, 8000H, that produces the maximum negative output voltage and adjust the offset potentiometer
or the offset adjust D/A converter for –10V (or 0V unipolar).
DAC714
SBAS032A
www.ti.com
7
DAC714 CALIBRATION VALUES
DIGITAL INPUT CODE
ANALOG OUTPUT (V)
BINARY TWO’S
BIPOLAR
UNIPOLAR
COMPLEMENT, BTC 20V RANGE 10V RANGE
DESCRIPTION
7FFFH
|
4000H
|
0001H
+9.999695
+9.999847
+ Full Scale –1LSB
+5.000000
+7.500000
3/4 Scale
+0.000305
+5.000153
BPZ + 1LSB
0000H
0.000000
+5.000000
Bipolar Zero (BPZ)
FFFFH
|
C000H
|
8000H
–0.000305
+4.999847
BPZ – 1LSB
–5.000000
+2.500000
1/4 Scale
–10.00000
0.000000
Minus Full Scale
1
16
2
−VCC 15
3
14
4
−12V to −15V
13
DAC714
5
12
6
DCOM
11
7
+VCC
10
8
ACOM
9
+
1µF
+12V to +15V
1µF
+
TABLE I. Digital Input and Analog Output Voltage Calibration Values.
FIGURE 4. Power Supply Connections.
Gain Adjustment
Apply the digital input that gives the maximum positive
voltage output. Adjust the gain potentiometer or the gain
adjust D/A converter for this positive full scale voltage.
INSTALLATION
GENERAL CONSIDERATIONS
Due to the high accuracy of the DAC714 system design,
problems such as grounding and contact resistance become
very important. A 16-bit converter with a 20V full-scale
range has a 1LSB value of 305µV. With a load current of
5mA, series wiring and connector resistance of only 60mΩ
will cause a voltage drop of 300µV. To understand what this
means in terms of a system layout, the resistivity of a typical
1 ounce copper-clad printed circuit board is 1/2 mΩ per
square. For a 5mA load, a 10 milliinch wide printed circuit
conductor 60 milliinches long will result in a voltage drop of
150µV.
The analog output of DAC714 has an LSB size of 305µV
(–96dB) in the bipolar mode. The rms noise floor of the D/A
should remain below this level in the frequency range of
interest. The DAC714’s output noise spectral density (which
includes the noise contributed by the internal reference,) is
shown in the Typical Characteristic section.
Wiring to high-resolution D/A converters should be routed
to provide optimum isolation from sources of RFI and EMI.
The key to elimination of RF radiation or pickup is small
loop area. Signal leads and their return conductors should be
kept close together such that they present a small capture
cross-section for any external field. Wire-wrap construction
is not recommended.
POWER SUPPLY AND
REFERENCE CONNECTIONS
Power supply decoupling capacitors should be added as
shown in Figure 4. Best performance occurs using a 1 to
10µF tantalum capacitor at –VCC. Applications with less
8
critical settling time may be able to use 0.01µF at –VCC
as well as at +VCC. The capacitors should be located
close to the package.
The DAC714 has separate ANALOG COMMON and DIGITAL COMMON pins. The current through DCOM is mostly
switching transients and are up to 1mA peak in amplitude.
The current through ACOM is typically 5µA for all codes.
Use separate analog and digital ground planes with a single
interconnection point to minimize ground loops. The analog
pins are located adjacent to each other to help isolate analog
from digital signals. Analog signals should be routed as far
as possible from digital signals and should cross them at
right angles. A solid analog ground plane around the D/A
package, as well as under it in the vicinity of the analog and
power supply pins, will isolate the D/A from switching
currents. It is recommended that DCOM and ACOM be
connected directly to the ground planes under the package.
If several DAC714s are used or if DAC714 shares supplies
with other components, connecting the ACOM and DCOM
lines to together once at the power supplies rather than at
each chip may give better results.
LOAD CONNECTIONS
Since the reference point for VOUT and VREF OUT is the
ACOM pin, it is important to connect the D/A converter load
directly to the ACOM pin. Refer to Figure 5.
Lead and contact resistances are represented by R1 through
R3. As long as the load resistance RL is constant, R1 simply
introduces a gain error and can be removed by gain adjustment of the D/A or system-wide gain calibration. R2 is part
of RL if the output voltage is sensed at ACOM.
In some applications it is impractical to return the load to the
ACOM pin of the D/A converter. Sensing the output voltage
at the SYSTEM GROUND point is reasonable, because there
is no change in DAC714 ACOM current, provided that R3 is
a low-resistance ground plane or conductor. In this case you
may wish to connect DCOM to SYSTEM GROUND as well.
DAC714
www.ti.com
SBAS032A
GAIN AND OFFSET ADJUST
Connections Using Potentiometers
GAIN and OFFSET adjust pins provide for trim using
external potentiometers. 15-turn potentiometers provide sufficient resolution. Range of adjustment of these trims is at
least ±0.3% of Full Scale Range. Refer to Figure 6.
Using D/A Converters
The GAIN ADJUST and OFFSET ADJUST circuits of
the DAC714 have been arranged so that these points may
be easily driven by external D/A converters. Refer to
Figure 7. 12-bit D/A converters provide an OFFSET
adjust resolution and a GAIN adjust resolution of 30µV
to 50µV per LSB step.
Nominal values of GAIN and OFFSET occur when the D/A
converters outputs are at approximately half scale, +5V.
OUTPUT VOLTAGE RANGE CONNECTIONS
The DAC714 output amplifier is connected internally to
provide a 20V output range. For other ranges and configurations, see Figures 6 and 7.
DIGITAL INTERFACE
SERIAL INTERFACE
The DAC714 has a serial interface with two data buffers
which can be used for either synchronous or asynchronous
updating of multiple D/A converters. A0 is the enable control
for the input shift register. A1 is the enable for the D/A Latch.
CLK is used to strobe data into the latches enabled by A0 and
A1. A CLR function is also provided and when enabled it sets
the shift register and the D/A Latch to 0000H (output voltage
is midscale).
Multiple DAC714s can be connected to the same CLK and
data lines in two ways. The output of the serial shift register
is available as SDO so that any number of DAC714s can be
cascaded on the same input bit stream as shown in Figures
8 and 9. This configuration allows all D/A converters to be
updated simultaneously and requires a minimum number of
control signals. These configurations do require 16N CLK
cycles to load any given D/A converter, where N is the
number of D/A converters.
The DAC714 can also be connected in parallel as shown in
Figure 10. This configuration allows any D/A converter in
the system to be updated in a maximum of 16 CLK cycles.
VREF RBPO
DAC714
10kΩ
SDI
RFB2
A0
A1
VREF
10kΩ
10kΩ
CLR
VOUT R1
Bus
Interface
RL
DCOM
Sense
Output
ACOM
R2
R3
Alternate Ground
Sense Connection
To +VCC
0.01µF(1)
0.01µF
System Ground
Analog
Power
Supply
To –VCC
NOTE: (1) Locate close to DAC714 package.
FIGURE 5. System Ground Considerations for High-Resolution D/A Converters.
DAC714
SBAS032A
www.ti.com
9
Internal
+10V Reference
VREF OUT
12
P1
1kΩ
180Ω
R1
100Ω
Gain Adjust
14
Offset Adjust
R2
2MΩ
10kΩ to 100kΩ
13
15kΩ
10kΩ
9.75kΩ
RFB2
9
IDAC
0-2mA
–VCC
R3
27kΩ
10
10kΩ
8
+VCC
VOUT
For no external adjustments, pins 13 and 14 are not
connected. External resistors R1 - R3 are standard ±1%
values. Range of adjustment at least ±0.3% FSR.
ACOM
FIGURE 6a. Manual Offset and Gain Adjust Circuits; Unipolar Mode (0V to +10V output range).
Internal
+10V Reference
VREF OUT
12
Bipolar Offset
11
P1
1kΩ
180Ω
P2
1kΩ
250Ω
R1
100Ω
Gain Adjust
Offset Adjust
15kΩ
14
13
10kΩ
9.75kΩ
10
10kΩ
RFB2
9
IDAC
0-2mA
8
R2
100Ω
ACOM
R3
27kΩ
R4
10kΩ
VOUT
For no external adjustments, pins 13 and 14 are not
connected. External resistors R1 - R4 are standard ±1%
values. Range of adjustment at least ±0.3% FSR.
FIGURE 6b. Manual Offset and Gain Adjust Circuits; Bipolar Mode (–5V to +5V output range).
10
DAC714
www.ti.com
SBAS032A
Internal
+10V Reference
VREF OUT
12
Bipolar Offset
180Ω
R2
1.3kΩ
R1
200Ω
250Ω
10kΩ
+10V
11
10kΩ
Gain Adjust
–10V
14
Offset Adjust
5kΩ
13
15kΩ
9.75kΩ 10kΩ
RFB2
10
Suggested Op Amps
OPA177GP, GS or
OPA604AP, AU
R4
24.3kΩ
R3
11.8kΩ
10kΩ
RFB VREF A
0 to +10V
IDAC
0-2mA
Suggested Op Amps
OPA177GP, GS: Single or
OPA2604AP, AU: Dual
9
±10V VOUT
0 to +10V
RFB VREF B
DAC714
For no external adjustments, pins 13 and 14 are not
connected. External resistors R1 - R4 tolerance: ±1%.
Range of adjustment at least ±0.3% FSR.
Suggested D/As
CMOS
DAC7800: Dual: Serial Input, 12-bit Resolution
DAC7801: Dual: 8-bit Port Input, 12-bit Resolution
DAC7802: Dual: 12-bit Port Input, 12-bit Resolution
DAC7528: Dual: 8-bit Port Input, 8-bit Resolution
DAC7545: Dual: 12-bit Port Input, 12-bit Resolution
DAC8043: Single: Serial Input, 12-bit Resolution
BIPOLAR (complete)
DAC813 (Use 11-bit resolution for 0V to +10V output. No op amps required).
FIGURE 7. Gain and Offset Adjustment in the Bipolar Mode Using D/A Converters (–10V to +10V output range).
DAC714
SBAS032A
www.ti.com
11
4
Data
2
Data Latch
3
Update
1
CLK
+5V 16
4
2
3
1
+5V 16
4
2
3
1
+5V 16
SDI
A0
A1
DAC714
CLK
CLR
SDO
5
SDI
A0
A1
DAC714
CLK
CLR
SDO
5
SDI
A0
A1
DAC714
CLK
CLR
SDO
5
To other DACs
FIGURE 8a. Cascaded Serial Bus Connection with Synchronous Update.
DAC3
DAC2
DAC1
Clock(1)
Data
F E D C B A 9 8 7 6 5 4
3 2 1 0 F E D C B A 9 8 7 6 5 4 3
2 1 0 F E D C B A 9 8 7 6 5 4 3 2 1 0
Data Latch
Update
FIGURE 8b. Timing Diagram For Figure 8a.
12
DAC714
www.ti.com
SBAS032A
4
Data
2
Data Latch
3
Update
1
16
SDI
A0
A1
DAC714
CLK
CLR
SDO
5
+5V
4
2
3
1
16
SDI
A0
A1
DAC714
CLK
CLR
SDO
5
+5V
4
2
3
1
16
SDI
A0
A1
DAC714
CLK
CLR
SDO
5
To other DACs
+5V
FIGURE 9a. Cascaded Serial Bus Connection with Asynchronous Update.
DAC3
DAC2
DAC1
Data Latch(1)
Data
F E D C B A 9 8 7 6 5 4
3 2 1 0 F E D C B A 9 8 7 6 5 4 3
2 1 0 F E D C B A 9 8 7 6 5 4 3 2 1 0
Update
FIGURE 9b. Timing Diagram For Figure 9a.
DAC714
SBAS032A
www.ti.com
13
Data
Data Latch 1
Update
4
2
3
1
CLK
16
CLR
4
Data Latch 2
2
3
1
16
4
Data Latch 3
2
3
1
16
SDI
A0
A1
DAC714
CLK
CLR
SDO
5
SDI
A0
A1
DAC714
CLK
CLR
SDO
5
SDI
A0
A1
DAC714
CLK
CLR
SDO
5
FIGURE 10a. Parallel Bus Connection.
DAC1
DAC2
DAC3
Clock(1)
Data
F E D C B A 9 8 7 6 5 4
3 2 1 0 F E D C B A 9 8 7 6 5 4 3
2 1 0 F E D C B A 9 8 7 6 5 4 3 2 1 0
Data Latch 1
Data Latch 2
Data Latch 3
Update
FIGURE 10b. Timing Diagram For Figure 10a.
14
DAC714
www.ti.com
SBAS032A
PACKAGE OPTION ADDENDUM
www.ti.com
21-May-2010
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
(Requires Login)
DAC714HB
OBSOLETE
CDIP SB
JD
16
TBD
Call TI
Call TI
DAC714HC
OBSOLETE
CDIP SB
JD
16
TBD
Call TI
Call TI
DAC714HL
OBSOLETE
CDIP SB
JD
16
Call TI
Call TI
DAC714P
NRND
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
DAC714PG4
NRND
PDIP
N
16
25
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
DAC714U
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
DAC714U/1K
ACTIVE
SOIC
DW
16
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
DAC714U/1KG4
ACTIVE
SOIC
DW
16
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
DAC714UG4
ACTIVE
SOIC
DW
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
TBD
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
21-May-2010
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
DAC714U/1K
Package Package Pins
Type Drawing
SOIC
DW
16
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
1000
330.0
16.4
Pack Materials-Page 1
10.75
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
10.7
2.7
12.0
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC714U/1K
SOIC
DW
16
1000
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
Similar pages