Engineering Bulletin Tentative Conductive Polymer Aluminum Solid Capacitors No.750A / Sep.2004 @Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte. (ESR and rated ripple current values are improved from PXC series.) @Rated voltage range : 2.5 to 16Vdc, Capacitance range : 33 to 1,200MF @Case size range : F5B5.8L to F10B7.7L @Suitable for DC-DC converters, voltage regulators and decoupling applications used to computer motherboards etc. Feature! Pb Free Type ?SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current -55 to +105C 2.5 to 16Vdc P20% (M) Rated voltageB1.15V I=0.2CV (max.) I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc) Dissipation Factor (tane) 0.12 max. Low Temperature Characteristics (Max. Impedance Ratio) Z(-25C)/Z(+20C)[1.15 Z(-55C)/Z(+20C)[1.25 (at 20C, 120Hz) (at 105C) (at 20C after 2 minutes) (at 20C, 120Hz) (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 105C. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at 60C, 90 to 95% RH for 500 hours. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value 1% per 1000 hours maximum (Confidence level 60% at 105C) Endurance Bias Humidity Surge Voltage Failure Rate *Note : If any doubt arises, measure the leakage current after following voltage treatment. Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C. ?DIMENSIONS [mm] ?MARKING @Terminal Code : A EX) 2.5V390MF 0.3max. LP0.3 AP0.2 ?PART NUMBERING SYSTEM 1 2 3 4 5 6 Size Code E61 F61 F80 H70 H80 J80 P CP0.2 BP0.2 FDP0.5 W 7 8 9 10 11 12 13 14 15 16 17 fD 5 6.3 6.3 8 8 10 L 5.8 5.8 7.7 6.7 7.7 7.7 A B C 5.3 5.3 5.9 6.6 6.6 7.2 6.6 6.6 7.2 8.3 8.3 9.0 8.3 8.3 9.0 10.3 10.3 11.0 W 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.7 to 1.1 0.7 to 1.1 0.7 to 1.1 P 1.4 1.9 1.9 3.1 3.1 4.5 E49A 390 2.5V 18 A PXE AAA A RA AAA M AAA G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 47MF:470,100MF:101) Taping code Terminal code Voltage code (ex. 6.3V:6R3,10V:100) Series code Category Specifications in this bulletin are subject to change without notice. Please ask us for technical specifications before purchase and use. NIPPON CHEMI-CON CORPORATION 1213 1 Engineering Bulletin Tentative Conductive Polymer Aluminum Solid Capacitors No.750A / Sep.2004 ?STANDARD RATINGS WV Cap (Vdc) (mF) 2.5 4 6.3 180 390 470 560 560 680 820 1000 1200 100 150 270 330 390 470 560 680 1000 100 120 220 270 330 Rated ripple current ESR Size (momax/20c, (mArms/100k to code 300kHz) 100kHz) -55 to +105c E61 F61 F80 F80 H70 H70 H80 H80 J80 E61 E61 F61 F61 F80 H70 H70 H80 J80 E61 E61 F61 F80 F80 21 15 13 13 13 13 12 12 13 22 22 15 15 14 14 14 13 14 24 24 15 14 14 2670 3160 3600 3600 4100 4100 4260 4260 4450 2610 2610 3160 3160 3470 3950 3950 3950 4300 2500 2500 3160 3470 3470 WV Cap (Vdc) (mF) Part No. APXE2R5ARA181ME61G APXE2R5ARA391MF61G APXE2R5ARA471MF80G APXE2R5ARA561MF80G APXE2R5ARA561MH70G APXE2R5ARA681MH70G APXE2R5ARA821MH80G APXE2R5ARA102MH80G APXE2R5ARA122MJ80G APXE4R0ARA101ME61G APXE4R0ARA151ME61G APXE4R0ARA271MF61G APXE4R0ARA331MF61G APXE4R0ARA391MF80G APXE4R0ARA471MH70G APXE4R0ARA561MH70G APXE4R0ARA681MH80G APXE4R0ARA102MJ80G APXE6R3ARA101ME61G APXE6R3ARA121ME61G APXE6R3ARA221MF61G APXE6R3ARA271MF80G APXE6R3ARA331MF80G 6.3 10 16 330 390 470 820 47 56 68 120 150 220 270 330 470 33 39 68 82 100 100 120 150 220 Rated ripple current ESR Size (momax/20c, (mArms/100k to code 300kHz) 100kHz) -55 to +105c H70 H70 H80 J80 E61 E61 E61 F61 F80 H70 H70 H80 J80 E61 E61 F61 F80 F80 H70 H70 H80 J80 14 14 13 14 28 28 28 25 21 21 21 19 19 35 35 28 24 24 24 24 22 22 3950 3950 3950 4300 2310 2310 2310 2530 2880 3220 3220 3390 3800 2070 2070 2390 2700 2700 3010 3010 3150 3450 Part No. APXE6R3ARA331MH70G APXE6R3ARA391MH70G APXE6R3ARA471MH80G APXE6R3ARA821MJ80G APXE100ARA470ME61G APXE100ARA560ME61G APXE100ARA680ME61G APXE100ARA121MF61G APXE100ARA151MF80G APXE100ARA221MH70G APXE100ARA271MH70G APXE100ARA331MH80G APXE100ARA471MJ80G APXE160ARA330ME61G APXE160ARA390ME61G APXE160ARA680MF61G APXE160ARA820MF80G APXE160ARA101MF80G APXE160ARA101MH70G APXE160ARA121MH70G APXE160ARA151MH80G APXE160ARA221MJ80G ?Recommended Reflow Soldering Conditions @Reflow Profile Method : Air or Infrated Reflow @Conditions [The times of reflow soldering : once] Peak temperature : 250C max. Max. period of time over 230C(T1) : 40 sec.max. Max. period of time over 200C(T2) : 60 sec.max. Preheat : 150Cmax., 120 sec. max. Temperature on the top of capacitor and Temperature of capacitor terminal (C) Peak temperature Peak 230 T1 200 [The times of reflow soldering : twice] Peak temperature : 250C max. Max. period of time over 230C(T1) : 30 sec.max. Max. period of time over 200C(T2) : 50 sec.max. Preheat : 150Cmax., 120 sec. max. T2 150 Preheat 120sec. max. 25 Time (sec.) ?Recommended Solder Land on PC Board c a b Size code E61 F61, F80 H70, H80 J80 a 1.4 1.9 3.1 4.5 b 3.0 3.5 4.2 4.4 c 1.6 1.6 2.2 2.2 Solder land on PC board Specifications in this bulletin are subject to change without notice. NIPPON CHEMI-CON CORPORATION 1213 2