TI CD4049UBDWR Cmos hex buffers/converter Datasheet

CD4049UB, CD4050B
August 1998 - Revised May 2004
Data sheet acquired from Harris Semiconductor
SCHS046I
CMOS Hex Buffer/Converters
Applications
The CD4049UB and CD4050B devices are inverting and
non-inverting hex buffers, respectively, and feature logiclevel conversion using only one supply voltage (VCC). The
input-signal high level (VIH) can exceed the VCC supply
voltage when these devices are used for logic-level
conversions. These devices are intended for use as CMOS
to DTL/TTL converters and can drive directly two DTL/TTL
loads. (VCC = 5V, VOL ≤ 0.4V, and IOL ≥ 3.3mA.)
• CMOS to DTL/TTL Hex Converter
• CMOS Current “Sink” or “Source” Driver
• CMOS High-To-Low Logic Level Converter
[ /Title
(CD40
49UB,
CD405 The CD4049UB and CD4050B are designated as
0B)
replacements for CD4009UB and CD4010B, respectively.
Because the CD4049UB and CD4050B require only one
/Subpower supply, they are preferred over the CD4009UB and
ject
CD4010B and should be used in place of the CD4009UB
(CMO and CD4010B in all inverter, current driver, or logic-level
S Hex conversion applications. In these applications the
Buffer/ CD4049UB and CD4050B are pin compatible with the
CD4009UB and CD4010B respectively, and can be
Consubstituted for these devices in existing as well as in new
verters) designs. Terminal No. 16 is not connected internally on the
/Autho CD4049UB or CD4050B, therefore, connection to this
terminal is of no consequence to circuit operation. For
r ()
applications not requiring high sink-current or voltage
/Keyconversion, the CD4069UB Hex Inverter is recommended.
words
(Harris Features
Semi- • CD4049UB Inverting
con• CD4050B Non-Inverting
ductor, • High Sink Current for Driving 2 TTL Loads
CD400 • High-To-Low Level Logic Conversion
• 100% Tested for Quiescent Current at 20V
0,
• Maximum Input Current of 1µA at 18V Over Full Package
metal
Temperature Range; 100nA at 18V and 25oC
gate,
• 5V, 10V and 15V Parametric Ratings
CMOS
Ordering Information
PART NUMBER
TEMP.
RANGE (oC)
PACKAGE
CD4049UBF3A
-55 to 125
16 Ld CERDIP
CD4050BF3A
-55 to 125
16 Ld CERDIP
CD4049UBD
-55 to 125
16 Ld SOIC
CD4049UBDR
-55 to 125
16 Ld SOIC
CD4049UBDT
-55 to 125
16 Ld SOIC
CD4049UBDW
-55 to 125
16 Ld SOIC
CD4049UBDWR
-55 to 125
16 Ld SOIC
CD4049UBE
-55 to 125
16 Ld PDIP
CD4049UBNSR
-55 to 125
16 Ld SOP
CD4049UBPW
-55 to 125
16 Ld TSSOP
CD4049UBPWR
-55 to 125
16 Ld TSSOP
CD4050BD
-55 to 125
16 Ld SOIC
CD4050BDR
-55 to 125
16 Ld SOIC
CD4050UBDT
-55 to 125
16 Ld SOIC
CD4050BDW
-55 to 125
16 Ld SOIC
CD4050BDWR
-55 to 125
16 Ld SOIC
CD4050BE
-55 to 125
16 Ld PDIP
CD4050NSR
-55 to 125
16 Ld SOP
CD4050BPW
-55 to 125
16 Ld TSSOP
CD4050BPWR
-55 to 125
16 Ld TSSOP
NOTE: When ordering, use the entire part number. The suffix R denotes tape
and reel. The suffix T denotes a small-quantity reel of 250.
Pinouts
CD4049UB (PDIP, CERDIP, SOIC, SOP, TSSOP)
TOP VIEW
16 NC
VCC 1
15 L = F
G=A 2
14 F
A 3
13 NC
H=B 4
B 5
12 K = E
11 E
I=C 6
10 J = D
C 7
9 D
VSS 8
1
CD4050B (PDIP, CERDIP, SOIC, SOP)
TOP VIEW
VCC 1
G=A 2
A 3
H=B 4
B 5
I=C 6
C 7
VSS 8
16 NC
15 L = F
14 F
13 NC
12 K = E
11 E
10 J = D
9 D
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
Copyright © 2004, Texas Instruments Incorporated
CD4049UB, CD4050B
Functional Block Diagrams
CD4049UB
A
B
C
D
E
F
3
2
5
4
7
6
9
10
11
12
14
15
VCC
VSS
CD4050B
G=A
A
H=B
B
I=C
C
J=D
D
K=E
E
L=F
F
1
3
2
5
4
7
6
9
10
11
12
14
15
VCC
8
VSS
NC = 13
NC = 16
G=A
H=B
I=C
J=D
K=E
L=F
1
8
NC = 13
NC = 16
Schematic Diagrams
VCC
VCC
P
OUT
R
IN
P
P
N
N
R
IN
N
VSS
FIGURE 1A. SCHEMATIC DIAGRAM OF CD4049UB, 1 OF 6
IDENTICAL UNITS
2
OUT
VSS
FIGURE 1B. SCHEMATIC DIAGRAM OF CD4050B, 1 OF 6
IDENTICAL UNITS
CD4049UB, CD4050B
Absolute Maximum Ratings
Thermal Information
Supply Voltage (V+ to V-). . . . . . . . . . . . . . . . . . . . . . . -0.5V to 20V
DC Input Current, Any One Input. . . . . . . . . . . . . . . . . . . . . . ±10mA
Package Thermal Impedance, θJA (see Note1):
E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67oC/W
D (SOIC) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73oC/W
DW (SOIC) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57oC/W
NS (SOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64oC/W
PW (TSSOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . 108oC/W
Maximum Junction Temperature (Plastic Package) . . . . . . . . .150oC
Maximum Storage Temperature Range . . . . . . . . . . . 65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .265oC
SOIC - Lead Tips Only
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. The package thermal impedance is calculated in accordance with JESD 51-7.
DC Electrical Specifications
LIMITS AT INDICATED TEMPERATURE (oC)
TEST CONDITIONS
PARAMETER
Quiescent Device Current
IDD (Max)
Output Low (Sink) Current
IOL (Min)
Output High (Source) Current
IOH (Min)
Out Voltage Low Level
VOL (Max)
Output Voltage High Level
VOH (Min)
Input Low Voltage, VIL (Max)
CD4049UB
Input Low Voltage, VIL (Max)
CD4050B
3
25
VO
(V)
VIN
(V)
VCC (V)
-55
-40
85
125
MIN
TYP
MAX
UNITS
-
0,5
5
1
1
30
30
-
0.02
1
µA
-
0,10
10
2
2
60
60
-
0.02
2
µA
-
0,15
15
4
4
120
120
-
0.02
4
µA
-
0,20
20
20
20
600
600
-
0.04
20
µA
0.4
0,5
4.5
3.3
3.1
2.1
1.8
2.6
5.2
-
mA
0.4
0,5
5
4
3.8
2.9
2.4
3.2
6.4
-
mA
0.5
0,10
10
10
9.6
6.6
5.6
8
16
-
mA
1.5
0,15
15
26
25
20
18
24
48
-
mA
4.6
0,5
5
-0.81
-0.73
-0.58
-0.48
-0.65
-1.2
-
mA
2.5
0,5
5
-2.6
-2.4
-1.9
-1.55
-2.1
-3.9
-
mA
9.5
0,10
10
-2.0
-1.8
-1.35
-1.18
-1.65
-3.0
-
mA
13.5
0,15
15
-5.2
-4.8
-3.5
-3.1
-4.3
-8.0
-
mA
-
0,5
5
0.05
0.05
0.05
0.05
-
0
0.05
V
-
0,10
10
0.05
0.05
0.05
0.05
-
0
0.05
V
-
0,15
15
0.05
0.05
0.05
0.05
-
0
0.05
V
-
0,5
5
4.95
4.95
4.95
4.95
4.95
5
-
V
-
0,10
10
9.95
9.95
9.95
9.95
9.95
10
-
V
-
0,15
15
14.95
14.95
14.95
14.95
14.95
15
-
V
4.5
-
5
1
1
1
1
-
-
1
V
9
-
10
2
2
2
2
-
-
2
V
13.5
-
15
2.5
2.5
2.5
2.5
-
-
2.5
V
0.5
-
5
1.5
1.5
1.5
1.5
-
-
1.5
V
1
-
10
3
3
3
3
-
-
3
V
1.5
-
15
4
4
4
4
-
-
4
V
CD4049UB, CD4050B
DC Electrical Specifications
(Continued)
LIMITS AT INDICATED TEMPERATURE (oC)
25
TEST CONDITIONS
PARAMETER
Input High Voltage, VIH Min
CD4049UB
Input High Voltage, VIH Min
CD4050B
Input Current, IIN Max
VO
(V)
VIN
(V)
VCC (V)
-55
-40
85
125
MIN
TYP
MAX
UNITS
0.5
-
5
4
4
4
4
4
-
-
V
1
-
10
8
8
8
8
8
-
-
V
1.5
-
15
12.5
12.5
12.5
12.5
12.5
-
-
V
4.5
-
5
3.5
3.5
3.5
3.5
3.5
-
-
V
9
-
10
7
7
7
7
7
-
-
V
13.5
-
15
11
11
11
11
11
-
-
V
-
±10-5
±0.1
µA
-
AC Electrical Specifications
0,18
18
±0.1
Propagation Delay Time
Low to High, tPLH
CD4049UB
Propagation Delay Time
Low to High, tPLH
CD4050B
Propagation Delay Time
High to Low, tPHL
CD4049UB
Propagation Delay Time
High to Low, tPHL
CD4050B
Transition Time, Low to High, tTLH
Transition Time, High to Low, tTHL
4
±1
±1
TA = 25oC, Input tr , tf = 20ns, CL = 50pF, RL = 200kΩ
TEST CONDITIONS
PARAMETER
±0.1
LIMITS (ALL PACKAGES)
VIN
VCC
TYP
MAX
UNITS
5
5
60
120
ns
10
10
32
65
ns
10
5
45
90
ns
15
15
25
50
ns
15
5
45
90
ns
5
5
70
140
ns
10
10
40
80
ns
10
5
45
90
ns
15
15
30
60
ns
15
5
40
80
ns
5
5
32
65
ns
10
10
20
40
ns
10
5
15
30
ns
15
15
15
30
ns
15
5
10
20
ns
5
5
55
110
ns
10
10
22
55
ns
10
5
50
100
ns
15
15
15
30
ns
15
5
50
100
ns
5
5
80
160
ns
10
10
40
80
ns
15
15
30
60
ns
5
5
30
60
ns
10
10
20
40
ns
15
15
15
30
ns
CD4049UB, CD4050B
AC Electrical Specifications
TA = 25oC, Input tr , tf = 20ns, CL = 50pF, RL = 200kΩ (Continued)
TEST CONDITIONS
LIMITS (ALL PACKAGES)
VIN
VCC
TYP
MAX
UNITS
Input Capacitance, CIN
CD4049UB
-
-
15
22.5
pF
Input Capacitance, CIN
CD4050B
-
-
5
7.5
pF
PARAMETER
TA = 25oC
TA = 25oC
SUPPLY VOLTAGE (VCC) = 5V
SUPPLY VOLTAGE (VCC) = 5V
VO , OUTPUT VOLTAGE (V)
VO , OUTPUT VOLTAGE (V)
Typical Performance Curves
5
4
MINIMUM
MAXIMUM
3
2
5
MINIMUM
4
MAXIMUM
3
2
1
1
0
1
2
3
0
4
1
2
VI , INPUT VOLTAGE (V)
3
4
FIGURE 2. MINIMUM AND MAXIMUM VOLTAGE TRANSFER
CHARACTERISTICS FOR CD4049UB
FIGURE 3. MINIMUM AND MAXIMUM VOLTAGE TRANSFER
CHARACTERISTICS FOR CD4050B
IOL, OUTPUT LOW (SINK) CURRENT (mA)
IOL, OUTPUT LOW (SINK) CURRENT (mA)
VI , INPUT VOLTAGE (V)
TA = 25oC
70
15V
60
10V
50
40
30
GATE TO SOURCE VOLTAGE (VGS) = 5V
20
10
0
1
2
3
4
5
6
7
8
VDS , DRAIN TO SOURCE VOLTAGE (V)
FIGURE 4. TYPICAL OUTPUT LOW (SINK) CURRENT
CHARACTERISTICS
5
TA = 25oC
70
15V
10V
60
50
40
30
20
GATE TO SOURCE VOLTAGE (VGS) = 5V
10
0
1
2
3
4
5
6
7
8
VDS , DRAIN TO SOURCE VOLTAGE (V)
FIGURE 5. MINIMUM OUTPUT LOW (SINK) CURRENT DRAIN
CHARACTERISTICS
CD4049UB, CD4050B
Typical Performance Curves
(Continued)
VDS, DRAIN TO SOURCE VOLTAGE (V)
-8
-7
-6
-5
-4
-3
-2
-1
VDS, DRAIN TO SOURCE VOLTAGE (V)
-8
-7
-6
-5
-4
-3
-2
0
-20
-25
-10V
-30
-15V
-10
VGS = -5V
-15
-10V
-20
-15V
-25
-30
-35
OUTPUT HIGH (SOURCE)
-15
GATE TO SOURCE VOLTAGE
CURRENT CHARACTERISTICS
-10
GATE TO SOURCE VOLTAGE
VGS = -5V
-35
FIGURE 6. TYPICAL OUTPUT HIGH (SOURCE) CURRENT
CHARACTERISTICS
FIGURE 7. MINIMUM OUTPUT HIGH (SOURCE) CURRENT
CHARACTERISTICS
10
9
VO, OUTPUT VOLTAGE (V)
10
VO, OUTPUT VOLTAGE (V)
0
-5
OUTPUT HIGH (SOURCE)
CURRENT CHARACTERISTICS
-5
SUPPLY VOLTAGE
8
VCC = 10V
125oC
7
6
TA = -55oC
VCC = 5V
5
4
-55oC
3
125oC
2
9
SUPPLY VOLTAGE
125oC
8
VCC = 10V
7
6
VCC = 5V
5
TA = -55oC
4
3
125oC
2
-55oC
1
1
0
0
0
1
2
3
4
0
5
6 7 8 9 10
VI , INPUT VOLTAGE (V)
105
TA = 25oC
V
C
104
Y
PL
GE
TA
L
VO
5
=1
VC
V
10
V
10
5V
P
SU
103
LOAD CAPACITANCE
CL = 50pF
(11pF FIXTURE + 39pF EXT)
CL = 15pF
(11pF FIXTURE + 4pF EXT)
102
10
10
102
103
104
f, INPUT FREQUENCY (kHz)
105
FIGURE 10. TYPICAL POWER DISSIPATION vs FREQUENCY
CHARACTERISTICS
6
1
2
3
4
5
6 7 8 9 10
VI , INPUT VOLTAGE (V)
FIGURE 9. TYPICAL VOLTAGE TRANSFER CHARACTERISTICS
AS A FUNCTION OF TEMPERATURE FOR CD4050B
POWER DISSIPATION PER INVERTER (µW)
FIGURE 8. TYPICAL VOLTAGE TRANSFER CHARACTERISTICS
AS A FUNCTION OF TEMPERATURE FOR CD4049UB
POWER DISSIPATION PER INVERTER (µW)
-1
TA = 25oC
TA = 25oC
TA = 25oC
105
15V; 1MHz
15V; 100kHz
10V; 100kHz
15V; 10kHz
10V; 10kHz
15V; 1kHz
104
103
102
10
SUPPLY VOLTAGE VCC = 5V FREQUENCY (f) = 10kHz
10
102
103
104
105
106
107
tr, tf , INPUT RISE AND FALL TIME (ns)
108
FIGURE 11. TYPICAL POWER DISSIPATION vs INPUT RISE
AND FALL TIMES PER INVERTER FOR CD4049UB
CD4049UB, CD4050B
POWER DISSIPATION PER INVERTER (µW)
Typical Performance Curves
(Continued)
106
TA = 25oC
105
15V; 1MHz
15V; 100kHz
10V; 100kHz
15V; 10kHz
10V; 10kHz
15V; 1kHz
104
103
102
10
SUPPLY VOLTAGE VCC = 5V FREQUENCY (f) = 10kHz
1
10
102
103
104
105
106
107
tr, tf , INPUT RISE AND FALL TIME (ns)
108
FIGURE 12. TYPICAL POWER DISSIPATION vs INPUT RISE
AND FALL TIMES PER INVERTER FOR CD4050B
Test Circuits
VCC
VCC
VCC
INPUTS
INPUTS
OUTPUTS
VIH
VSS
+
DVM
VIL
IDD
VSS
VSS
NOTE: Test any one input with other inputs at VCC or VSS.
FIGURE 13. QUIESCENT DEVICE CURRENT TEST CIRCUIT
FIGURE 14. INPUT VOLTAGE TEST CIRCUIT
CMOS 10V LEVEL TO DTL/TTL 5V LEVEL
VCC = 5V
VCC
INPUTS
COS/MOS
IN
OUTPUTS
VCC
OUTPUT
TO DTL/TTL
CD4049
INPUTS
I
5V = VOH
10V = VIH
0 = VIL
VSS
VSS
NOTE: Measure inputs sequentially, to both VCC and VSS connect
all unused inputs to either VCC or VSS.
FIGURE 15. INPUT CURRENT TEST CIRCUIT
7
VSS
0 = VOL
In Terminal - 3, 5, 7, 9, 11, or 14
Out Terminal - 2, 4, 6, 10, 12 or 15
VCC Terminal - 1
VSS Terminal - 8
FIGURE 16. LOGIC LEVEL CONVERSION APPLICATION
CD4049UB, CD4050B
(Continued)
VDD
0.1µF
500µF
CL
10kHz,
100kHz, 1MHz
I
1
2
3
4
5
6
7
8
CD4049UB
Test Circuits
16
15
14
13
12
11
10
9
CL INCLUDES FIXTURE CAPACITANCE
FIGURE 17. DYNAMIC POWER DISSIPATION TEST CIRCUITS
8
CD4049UB, CD4050B
9
PACKAGE OPTION ADDENDUM
www.ti.com
28-Feb-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
CD4049UBD
ACTIVE
SOIC
D
16
40
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
CD4049UBDR
ACTIVE
SOIC
D
16
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
CD4049UBDT
ACTIVE
SOIC
D
16
250
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
CD4049UBDW
ACTIVE
SOIC
DW
16
40
Pb-Free
(RoHS)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
CD4049UBDWR
ACTIVE
SOIC
DW
16
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
CD4049UBE
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
Level-NC-NC-NC
CD4049UBF
ACTIVE
CDIP
J
16
1
None
Call TI
Level-NC-NC-NC
CD4049UBF3A
ACTIVE
CDIP
J
16
1
None
Call TI
Level-NC-NC-NC
CD4049UBM
OBSOLETE
SOIC
D
16
None
Call TI
Call TI
Call TI
CD4049UBM96
OBSOLETE
SOIC
D
16
None
Call TI
CD4049UBNSR
ACTIVE
SO
NS
16
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
CD4049UBPW
ACTIVE
TSSOP
PW
16
90
Pb-Free
(RoHS)
CU NIPDAU
Level-1-250C-UNLIM
CD4049UBPWR
ACTIVE
TSSOP
PW
16
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-1-250C-UNLIM
CD4050BD
ACTIVE
SOIC
D
16
40
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
CD4050BDR
ACTIVE
SOIC
D
16
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
CD4050BDT
ACTIVE
SOIC
D
16
250
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
CD4050BDW
ACTIVE
SOIC
DW
16
40
Pb-Free
(RoHS)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
CD4050BDWR
ACTIVE
SOIC
DW
16
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-2-250C-1 YEAR/
Level-1-235C-UNLIM
CD4050BE
ACTIVE
PDIP
N
16
25
Pb-Free
(RoHS)
CU NIPDAU
Level-NC-NC-NC
CD4050BF
ACTIVE
CDIP
J
16
1
None
Call TI
Level-NC-NC-NC
CD4050BF3A
ACTIVE
CDIP
J
16
1
None
Call TI
Level-NC-NC-NC
Call TI
CD4050BM
OBSOLETE
SOIC
D
16
None
Call TI
CD4050BNSR
ACTIVE
SO
NS
16
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1 YEAR/
Level-1-235C-UNLIM
CD4050BPW
ACTIVE
TSSOP
PW
16
90
Pb-Free
(RoHS)
CU NIPDAU
Level-1-250C-UNLIM
CD4050BPWR
ACTIVE
TSSOP
PW
16
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-1-250C-UNLIM
JM38510/05553BEA
ACTIVE
CDIP
J
16
1
None
Call TI
Level-NC-NC-NC
JM38510/05554BEA
ACTIVE
CDIP
J
16
1
None
Call TI
Level-NC-NC-NC
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
28-Feb-2005
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated
Similar pages