EtronTech EM6A9320BIB 4M x 32 bit DDR Synchronous DRAM (SDRAM) Etron Confidential Advanced (Rev 1.0, July /2012) Features Overview • Fast clock rate: 200/250 MHz • Differential Clock CK & CK input The EM6A9320 DDR SDRAM is a high-speed CMOS double data rate synchronous DRAM containing 128 Mbits. It is internally configured as a quad 1M x 32 DRAM with a synchronous interface (all signals are registered on the positive edge of the clock signal, CK). Data outputs occur at both rising edges of CK and CK . Read and write accesses to the SDRAM are burst oriented; accesses start at a selected location and continue for a programmed number of locations in a programmed sequence. • 4 Bi-directional DQS. Data transactions on both edges of DQS (1DQS / Byte) • DLL aligns DQ and DQS transitions • Edge aligned data & DQS output • Center aligned data & DQS input • 4 internal banks, 1M x 32-bit for each bank • Programmable mode and extended mode registers - CAS Latency: 2, 2.5, 3 - Burst length: 2, 4, 8 - Burst Type: Sequential & Interleave • All inputs except DQ’s & DM are at the positive edge of the system clock • 4 individual DM control for write masking only • Auto Refresh and Self Refresh • 4096 refresh cycles / 64ms • Industrial Operating Temperature: -40~85℃ • Power supplies: VDD & VDDQ = 2.5V ± 0.2V • Interface: SSTL_2 I/O compatible • 144-ball 12 x 12 x 1.4mm LFBGA package -Pb and Halogen Free Accesses begin with the registration of a BankActivate command, which is then followed by a Read or Write command. The EM6A9320 provides programmable Read or Write burst lengths of 2, 4, 8. An auto precharge function may be enabled to provide a self-timed row precharge that is initiated at the end of the burst sequence.The refresh functions, either Auto or Self Refresh are easy to use. In addition, EM6A9320 features programmable DLL option. By having a programmable mode register and extended mode register, the system can choose the most suitable modes to maximize its performance. These devices are well suited for applications requiring high memory bandwidth, result in a device particularly well suited to high performance main memory and graphics applications. Table1. Ordering Information Part Number Clock Frequency Data Rate EM6A9320BIB-4IH 250MHz 500Mbps/pin EM6A9320BIB-5IH 200MHz 400Mbps/pin BI: indicates LFBGA package B: indicates generation code I: indicates Industrial grade H: indicates Pb and Halogen Free for LFBGA Package Power Supply VDD 2.5V, VDDQ 2.5V VDD 2.5V, VDDQ 2.5V Package LFBGA LFBGA Etron Technology, Inc. No. 6, Technology Rd. V, Hsinchu Science Park, Hsinchu, Taiwan 30078, R.O.C. TEL: (886)-3-5782345 FAX: (886)-3-5778671 Etron Technology, Inc. reserves the right to change products or specification without notice. EtronTech EM6A9320BIB Figure 1. Pin Assignment (LFBGA 144Ball Top View) 1 2 3 4 5 6 7 8 9 10 11 12 A DQS0 DM0 VSSQ DQ3 DQ2 DQ0 DQ31 DQ29 DQ28 VSSQ DM3 DQS3 B DQ4 VDDQ NC VDDQ DQ1 VDDQ VDDQ DQ30 VDDQ NC VDDQ DQ27 C DQ6 DQ5 VSSQ VSSQ VSSQ VDD VDD VSSQ VSSQ VSSQ DQ26 DQ25 D DQ7 VDDQ VDD VSS VSSQ VSS VSS VSSQ VSS VDD VDDQ DQ24 E DQ17 DQ16 VDDQ VSSQ VSS VSS VSS VSS VSSQ VDDQ DQ15 DQ14 F DQ19 DQ18 VDDQ VSSQ VSS VSS VSS VSS VSSQ VDDQ DQ13 DQ12 G DQS2 DM2 NC VSSQ VSS VSS VSS VSS VSSQ NC DM1 DQS1 H DQ21 DQ20 VDDQ VSSQ VSS VSS VSS VSS VSSQ VDDQ DQ11 DQ10 J DQ22 DQ23 VDDQ VSSQ VSS VSS VSS VSS VSSQ VDDQ DQ9 DQ8 K CAS WE VDD VSS A10 VDD VDD NC VSS VDD NC NC L RAS NC NC BA1 A2 A11 A9 A5 NC CK CK NC M CS NC BA0 A0 A1 A3 A4 A6 A7 A8 CKE VREF Table 2. Pin Assignment by Name (LFBGA 144Ball) Symbol Location Symbol Location Symbol Location Symbol Location Symbol Location Symbol Location Symbol Location Symbol Location A0 M4 DQ6 C1 DQ24 D12 CK L10 VDDQ B6 VSS E5 VSS J7 VSSQ G4 A1 M5 DQ7 D1 DQ25 C12 L11 VDDQ B7 VSS E6 VSS J8 VSSQ G9 CK A2 L5 DQ8 J12 DQ26 C11 CKE M11 VDDQ B9 VSS E7 VSS K4 VSSQ H4 A3 M6 DQ9 J11 DQ27 B12 M1 VDDQ B11 VSS E8 VSS K9 VSSQ H9 CS A4 M7 DQ10 H12 DQ28 A9 RAS L1 VDDQ D2 VSS F5 VSSQ A3 VSSQ J4 A5 L8 DQ11 H11 DQ29 A8 CAS K1 VDDQ D11 VSS F6 VSSQ A10 VSSQ J9 A6 A7 A8/AP A9 A10 A11 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 M8 M9 M10 L7 K5 L6 A6 B5 A5 A4 B1 C2 DQ12 DQ13 DQ14 DQ15 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 F12 F11 E12 E11 E2 E1 F2 F1 H2 H1 J1 J2 DQ30 DQ31 DQS0 DQS1 DQS2 DQS3 DM0 DM1 DM2 DM3 BA0 BA1 B8 A7 A1 G12 G1 A12 A2 G11 G2 A11 M3 L4 WE VREF VDD VDD VDD VDD VDD VDD VDD VDD VDDQ VDDQ K2 M12 C6 C7 D3 D10 K3 K6 K7 K10 B2 B4 VDDQ VDDQ VDDQ VDDQ VDDQ VDDQ VDDQ VDDQ VSS VSS VSS VSS E3 E10 F3 F10 H3 H10 J3 J10 D4 D6 D7 D9 VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS VSS F7 F8 G5 G6 G7 G8 H5 H6 H7 H8 J5 J6 VSSQ VSSQ VSSQ VSSQ VSSQ VSSQ VSSQ VSSQ VSSQ VSSQ VSSQ VSSQ C3 C4 C5 C8 C9 C10 D5 D8 E4 E9 F4 F9 NC NC NC NC NC NC NC NC NC NC NC NC B3 B10 G3 G10 K8 K11 K12 L2 L3 L9 L12 M2 Etron Confidential 2 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 2. Block Diagram DLL CLOCK BUFFER Row Decoder CKE Column Decoder CS RAS CAS WE COMMAND DECODER A8/AP COLUMN COUNTER DQS0~3 DQ0 MODE REGISTER Column Decoder ADDRESS BUFFER REFRESH COUNTER DATA STROBE BUFFER 4096 x 256 x 32 CELL ARRAY (BANK #2) Column Decoder DQ Buffer ~ DQ31 DM0~3 Etron Confidential 4096 x 256 x 32 CELL ARRAY (BANK #1) Row Decoder A9 A10 A11 BA0 BA1 CONTROL SIGNAL GENERATOR Row Decoder ~ A0 4096 x 256 x 32 CELL ARRAY (BANK #0) Row Decoder CK CK 3 4096 x 256 x 32 CELL ARRAY (BANK #3) Column Decoder Rev 1.0 July /2012 EtronTech EM6A9320BIB Pin Descriptions Table 3. Pin Details of EM6A9320 Symbol CK, CK Type Input CKE Input BA0, BA1 Input A0-A11 Input CS Input RAS Input Row Address Strobe: The RAS signal defines the operation commands in conjunction with the CAS and /WE signals and is latched at the positive edges of CK. When RAS and CS are asserted "LOW" and CAS is asserted "HIGH" either the BankActivate command or the Precharge command is selected by the WE signal. When the WE is asserted "HIGH," the BankActivate command is selected and the bank designated by BA is turned on to the active state. When the WE is asserted "LOW," the Precharge command is selected and the bank designated by BA is switched to the idle state after the precharge operation. CAS Input Column Address Strobe: The CAS signal defines the operation commands in conjunction with the RAS and /WE signals and is latched at the positive edges of CK. When /RAS is held "HIGH" and CS is asserted "LOW" the column access is started by asserting CAS "LOW" Then, the Read or Write command is selected by asserting WE "HIGH " or “LOW". WE Input DQS0-DQS3 Input / Output DM0 - DM3 Input DQ0 - DQ31 Input / Output Supply Supply Write Enable: The WE signal defines the operation commands in conjunction with the RAS and CAS signals and is latched at the positive edges of CK. The WE input is used to select the BankActivate or Precharge command and Read or Write command. Bidirectional Data Strobe: The DQSx signals are mapped to the following data bytes: DQS0 to DQ0-DQ7, DQS1 to DQ8-DQ15, DQS2 to DQ16-DQ23, and DQS3 to DQ24-DQ31. Data Input Mask: DM0-DM3 are byte specific. Input data is masked when DM is sampled HIGH during a write cycle. DM3 masks DQ31-DQ24, DM2 masks DQ23DQ16, DM1 masks DQ15-DQ8, and DM0 masks DQ7-DQ0. Data I/O: The DQ0-DQ31 input and output data are synchronized with positive and negative edges of DQS0~DQS3. The I/Os are byte-maskable during Writes. Power Supply: Power for the input buffers and core logic. VDD VSS Etron Confidential Description Differential Clock: CK, CK are driven by the system clock. All SDRAM input commands are sampled on the positive edge of CK. Both CK and CK increment the internal burst counter and controls the output registers. Clock Enable: CKE activates (HIGH) and deactivates (LOW) the CK signal. If CKE goes low synchronously with clock, the internal clock is suspended from the next clock cycle and the state of output and burst address is frozen as long as the CKE remains low. When all banks are in the idle state, deactivating the clock controls the entry to the Power Down and Self Refresh modes. Bank Activate: BA0 and BA1 define to which bank the BankActivate, Read, Write, or BankPrecharge command is being applied. They also define which Mode Register or Extended Mode Register is loaded during a Mode Register Set command. Address Inputs: A0-A11 are sampled during the Bank Activate command (row address A0-A11) and Read/Write command (column address A0-A7 with A8 defining Auto Precharge) to select one location out of the 1M available in the respective bank. During a Precharge command, A8 is sampled to determine if all banks are to be precharged (A8 = HIGH). The address inputs also provide the op-code during a Mode Register Set or Extended Mode Register Set command. Chip Select: CS enables (sampled LOW) and disables (sampled HIGH) the command decoder. All commands are masked when CS is sampled HIGH. CS provides for external bank selection on systems with multiple banks. It is considered part of the command code. Ground: Ground for the input buffers and core logic. 4 Rev 1.0 July /2012 EtronTech VDDQ VSSQ VREF NC Supply Supply Supply - Etron Confidential EM6A9320BIB DQ Power: Provide isolated power to DQs for improved noise immunity. DQ Ground: Provide isolated ground to DQs for improved noise immunity. Reference Voltage for Inputs: +0.5 x VDDQ No Connect: No internal connection, these pins suggest to be left unconnected. 5 Rev 1.0 July /2012 EtronTech EM6A9320BIB Operation Mode Table 4 shows the truth table for the operation commands. Table 4. Truth Table (Note (1), (2)) Command State BankActivate BankPrecharge Precharge All Write Write and AutoPrecharge Read Read and Autoprecharge Mode Register Set Extended Mode Register Set No-Operation Device Deselect Burst Stop AutoRefresh SelfRefresh Entry Idle(3) SelfRefresh Exit Any Any Active(3) Active(3) Active(3) Active(3) Idle Idle Any Any Active(4) Idle Idle Idle (Self Refresh) CKEn-1 CKEn DM BA1 BA0 A8 A11-A9, A7-0 CS H H H H H H H H H H H H H H X X X X X X X X X X X X H L X X X V V X X X X X X X X X V V X V V V V L L X X X X X V V X V V V V L H X X X X X Row Address L X H X L Column H Address L A0~A7 H X X X X X X X X X X L H X X X X X OP code Power Down Mode Entry Idle/Active(5) H L X X X X X Power Down Mode Exit Any (Power Down) L H X X X X X L L L L L L L L L L H L L L H L H L H L X X RAS CAS L L L H H H H L L H X H L L X H X H X H X X H H H L L L L L L H X H L L X H X H X H X X Data Mask Enable(6) Active H X H X X X X Data Mask Disable Active H X L X X X X Note: 1. V = Valid data, X = Don't Care, L = Low level, H = High level 2. CKEn signal is input level when commands are provided. CKEn-1 signal is input level one clock cycle before the commands are provided. 3. These are states of bank designated by BA0, BA1signals. 4. Read burst stop with BST command for all burst types. 5. Power Down Mode can not enter in the burst operation. When this command is asserted in the burst cycle, device state is clock suspend mode. 6. DM0 – DM3 can be enabled respectively. Etron Confidential 6 Rev 1.0 WE H L L L L H H L L H X L H H X H X H X H X X July /2012 EtronTech EM6A9320BIB Mode Register Set (MRS) The Mode Register stores the data for controlling various operating modes of a DDR SDRAM. It programs CAS Latency, Burst Type, and Burst Length to make the DDR SDRAM useful for a variety of applications. The default value of the Mode Register is not defined; therefore the Mode Register must be written by the user. Values stored in the register will be retained until the register is reprogrammed. The Mode Register is written by asserting Low on CS , RAS , CAS , WE , BA1 and BA0 (the device should have all banks idle with no bursts in progress prior to writing into the mode register, and CKE should be High). The state of address pins A0~A11 and BA0, BA1 in the same cycle in which CS , RAS , CAS and WE are asserted Low is written into the Mode Register. A minimum of two clock cycles, tMRD, are required to complete the write operation in the Mode Register. The Mode Register is divided into various fields depending on functionality. The Burst Length uses A0~A2, Burst Type uses A3, and CAS Latency (read latency from column address) uses A4~A6. A logic 0 should be programmed to all the undefined addresses to ensure future compatibility. Reserved states should not be used to avoid unknown device operation or incompatibility with future versions. Refer to the table for specific codes for various burst lengths, burst types and CAS latencies. Table 5. Mode Register Bitmap BA1 BA0 A11 0 A8 0 1 X 0 A10 A9 A8 0 A7 Test Mode 0 Normal mode 0 DLL Reset 1 Test mode BA0 Mode 0 MRS 1 EMRS A7 T.M. A6 0 0 0 0 1 1 1 1 A5 0 0 1 1 0 0 1 1 A6 A5 A4 CAS Latency A4 CAS Latency 0 Reserved 1 Reserved 0 2 1 3 0 Reserved 1 Reserved 0 2.5 1 Reserved A3 BT A2 A1 A0 Burst Length A3 Burst Type 0 Sequential 1 Interleave A2 0 0 0 0 1 1 1 1 A1 0 0 1 1 0 0 1 1 A0 0 1 0 1 0 1 0 1 Address Field Mode Register Burst Length Reserved 2 4 8 Reserved Reserved Reserved Reserved • Burst Length Field (A2~A0) This field specifies the data length of column access using the A2~A0 pins and selects the Burst Length to be 2, 4, and 8. Table 6. Burst Length A2 A1 A0 Burst Length 0 0 0 Reserved 0 0 1 2 0 1 0 4 0 1 1 8 1 0 0 Reserved 1 0 1 Reserved 1 1 0 Reserved 1 1 1 Reserved Etron Confidential 7 Rev 1.0 July /2012 EtronTech EM6A9320BIB • Addressing Mode Select Field (A3) The Addressing Mode can be one of two modes, either Interleave Mode or Sequential Mode. Both Sequential Mode and Interleave Mode support burst length of 2, 4, and 8. Table 7. Addressing Mode • A3 Addressing Mode 0 Sequential 1 Interleave Burst Definition, Addressing Sequence of Sequential and Interleave Mode Table 8. Burst Address ordering Burst Length 2 4 8 Start Address A2 A1 A0 X X 0 X X 1 X 0 0 X 0 1 X 1 0 X 1 1 0 0 0 0 0 1 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 Sequential Interleave 0, 1 1, 0 0, 1, 2, 3 1, 2, 3, 0 2, 3, 0, 1 3, 0, 1, 2 0, 1, 2, 3, 4, 5, 6, 7 1, 2, 3, 4, 5, 6, 7, 0 2, 3, 4, 5, 6, 7, 0, 1 3, 4, 5, 6, 7, 0, 1, 2 4, 5, 6, 7, 0, 1, 2, 3 5, 6, 7, 0, 1, 2, 3, 4 6, 7, 0, 1, 2, 3, 4, 5 7, 0, 1, 2, 3, 4, 5, 6 0, 1 1, 0 0, 1, 2, 3 1, 0, 3, 2 2, 3, 0, 1 3, 2, 1, 0 0, 1, 2, 3, 4, 5, 6, 7 1, 0, 3, 2, 5, 4, 7, 6 2, 3, 0, 1, 6, 7, 4, 5 3, 2, 1, 0, 7, 6, 5, 4 4, 5, 6, 7, 0, 1, 2, 3 5, 4, 7, 6, 1, 0, 3, 2 6, 7, 4, 5, 2, 3, 0, 1 7, 6, 5, 4, 3, 2, 1, 0 • CAS Latency Field (A6~A4) This field specifies the number of clock cycles from the assertion of the Read command to the first read data. The minimum whole value of CAS Latency depends on the frequency of CK. The minimum whole value satisfying the following formula must be programmed into this field. tCAC (min) ≤ CAS Latency X tCK Table 9. CAS Latency A6 A5 A4 CAS Latency 0 0 0 Reserved 0 0 1 Reserved 0 1 0 2 clocks 0 1 1 3 clocks 1 0 0 Reserved 1 0 1 Reserved 1 1 0 2.5 clocks 1 1 1 Reserved Etron Confidential 8 Rev 1.0 July /2012 EtronTech EM6A9320BIB • Test Mode Field (A8~A7) These two bits are used to enter the test mode and must be programmed to "00" in normal operation. Table 10. Test Mode • A8 A7 Test Mode 0 0 Normal mode 1 0 DLL Reset X 1 Test mode (BA0, BA1) Table 11. MRS/EMRS BA1 BA0 A11 ~ A0 RFU 0 MRS Cycle RFU 1 Extended Functions (EMRS) Extended Mode Register Set (EMRS) The Extended Mode Register Set stores the data for enabling or disabling DLL and selecting output driver strength. The default value of the extended mode register is not defined, therefore must be written after power up for proper operation. The extended mode register is written by asserting low on CS , RAS , CAS , and WE . (the device should have all banks idle with no bursts in progress prior to writing into the mode register, and CKE should be High)The state of A0 ~ A11 and BA1 are written in the mode register in the same cycle as CK , RAS , CAS , and WE going low. The DDR SDRAM should be in all bank precharge with CKE already high prior to writing into the extended mode register. A1 is used for setting driver strength. Two clock cycles are required to complete the write operation in the extended mode register. The mode register contents can be changed using the same command and clock cycle requirements during operation as long as all banks are in the idle state. A0 is used for DLL enable or disable. "High" on BA0 is used for EMRS. Refer to the table for specific codes. Table 12. Extended Mode Register Bitmap BA1 BA0 A11 A10 0 BA0 0 1 1 A9 A8 A7 A6 A5 A4 A3 RFU must be set to “0” Mode MRS EMRS Etron Confidential A1 0 1 Drive Strength Full Reserved 9 A2 A1 DS A0 0 1 A0 Address Field DLL Extended Mode Register DLL Enable Disable Rev 1.0 July /2012 EtronTech EM6A9320BIB Table 13. Absolute Maximum Rating Input, Output Voltage Rating -4I/5I - 0.5 ~ VDDQ+0.5 V 1,2 VDD, VDDQ Power Supply Voltage -1 ~ 3.6 V 1,2 TA Ambient Temperature -40~85 1 TSTG Storage Temperature - 55~150 °C °C °C W 1 Symbol VIN, VOUT TSOLDER PD Item Soldering Temperature (10s) 260 Power Dissipation 2.0 Unit Note 1 1 IOS 50 mA 1 Short Circuit Output Current Note1: Stress greater than those listed under “Absolute Maximum Ratings” may cause permanent damage of the devices Note2: These voltages are relative to Vss Table 14. Recommended D.C. Operating Conditions (SSTL_2 In/Out, TA = -40 ~ 85 °C) Symbol VDD Parameter Power Supply Voltage Min. 2.3 Max. 2.7 Unit V Note 1 VDDQ Power Supply Voltage(for I/O ) 2.3 2.7 V 1 VREF Input Reference Voltage 0.49 x VDDQ 0.51 x VDDQ V VTT Termination Voltage VREF – 0.04 VREF + 0.04 V VIH(DC) Input High Voltage VREF + 0.15 VDDQ + 0.3 V VIL(DC) Input Low Voltage VSSQ - 0.3 VREF- 0.15 V IIL Input Leakage Current -2 2 µA IOZ Output Leakage Current -5 5 µA IOH Output High Current -16.2 - mA VOH = 1.95V IOL Output Low Current 16.2 - mA VOL = 0.35V Min. Max. Unit 1.5 2.5 pF Table 15. Capacitance (VDD = 2.5V, f = 1MHz, TA = 25 °C) Symbol CIN1 Parameter Input Capacitance (CK, CK ) CIN2 Input Capacitance (All other input-only pins) 1.5 2.5 pF CI/O DM, DQ, DQS Input/Output Capacitance 3.5 4.5 pF Note: These parameters are guaranteed by design, periodically sampled and are not 100% tested. Table 16. Decoupling Capacitance Guide Line Symbol Parameter CDC1 Decouping Capacitance between VDD and VSS CDC2 Decouping Capacitance between VDDQ and VSSQ Etron Confidential 10 Value 0.1+0.01 0.1+0.01 Unit µF µF Rev 1.0 July /2012 EtronTech EM6A9320BIB Table 17. D.C. Characteristics (VDD=2.5V ± 0.2V, TA =-40~85°C) Parameter & Test Condition Symbol OPERATING CURRENT: One bank; Active-Precharge; tRC=tRC (min); tCK=tCK (min); DQ, DM and DQS inputs changing once per clock cycle; Address and control inputs changing once every two clock cycles. OPERATING CURRENT : One bank; Active-Read-Precharge; BL=4; tRC=tRC(min); tCK=tCK(min); lout=0mA; Address and control inputs changing once per clock cycle PRECHARGE POWER-DOWN STANDBY CURRENT: All banks idle; power-down mode; tCK=tCK(min); CKE=LOW IDLE STANDBY CURRENT : CKE = HIGH; CS =HIGH(DESELECT); All banks idle; tCK=tCK(min); Address and control inputs changing once per clock cycle; VIN=VREF for DQ, DQS and DM ACTIVE POWER-DOWN STANDBY CURRENT : one bank active; powerdown mode; CKE=LOW; tCK=tCK(min) -5I Max. Unit IDD0 220 210 mA IDD1 260 240 mA IDD2P 75 75 mA IDD2N 100 100 mA IDD3P 75 75 mA 230 220 mA 440 420 mA 440 420 mA 330 300 mA 6 6 mA 600 570 mA ACTIVE STANDBY CURRENT : CS =HIGH;CKE=HIGH; one bank active ; IDD3N tRC=tRC(max);tCK=tCK(min);Address and control inputs changing once per clock cycle; DQ,DQS,and DM inputs changing twice per clock cycle OPERATING CURRENT BURST READ : BL=2; READs; Continuous burst; one bank active; Address and control inputs changing once per clock IDD4R cycle; tCK=tCK(min); lout=0mA;50% of data changing on every transfer OPERATING CURRENT BURST Write : BL=2; WRITES; Continuous Burst ;one bank active; address and control inputs changing once per clock IDD4W cycle; tCK=tCK(min); DQ,DQS,and DM changing twice per clock cycle; 50% of data changing on every transfer IDD5 AUTO REFRESH CURRENT : tRC=tRFC(min); tCK=tCK(min) SELF REFRESH CURRENT: Self Refresh Mode ; IDD6 CKE≦0.2V;tCK=tCK(min) BURST OPERATING CURRENT 4 bank operation: Four bank interleaving READs; BL=4;with Auto Precharge; tRC=tRC(min); tCK=tCK(min); Address and control inputs change only during Active, READ , or WRITE command -4I IDD7 Note: 1. Stress greater than those listed under "Absolute Maximum Ratings" may cause permanent damage of the device. 2. All voltages are referenced to VSS. 3. These parameters depend on the cycle rate and these values are measured by the cycle rate under the minimum value of tCK and tRC. Input signals are changed one time during tCK. 4. Power-up sequence is described in later page. Etron Confidential 11 Rev 1.0 July /2012 EtronTech EM6A9320BIB Table 18. Electrical Characteristics and Recommended A.C. Operating Conditions (VDD = 2.5V ± 0.2V, TA = -40~85 °C) Symbol -4I Parameter -5I tCK Clock cycle time tCH tCL Clock high level width Clock low level width tDQSCK DQS-out access time from CK, CK -0.6 0.6 -0.6 0.6 ns tAC -0.7 0.7 -0.7 0.7 ns tDQSQ tRPRE tRPST tDQSS tWPRES tWPRE tWPST tDQSH tDQSL tIS tIH tDS tDH Output access time from CK, CK DQS-DQ Skew Read preamble Read postamble CK to valid DQS-in DQS-in setup time DQS Write preamble DQS write postamble DQS in high level pulse width DQS in low level pulse width Address and Control input setup time Address and Control input hold time DQ & DM setup time to DQS DQ & DM hold time to DQS 0.4 1.1 0.6 1.25 0.6 - ns tCK tCK tCK ns tCK tCK tCK tCK ns ns ns ns Clock half period - ns tQH tRC tRFC tRAS tRCD tRP tRRD tWR tMRD tDAL tXSRD tPDEX tREFI tIPW tDIPW DQ/DQS output hold time from DQS Row cycle time Refresh row cycle time Row active time Active to Read or Write delay Row precharge time Row active to Row active delay Write recovery time Mode register set cycle time Auto precharge write recovery + Precharge time Self refresh exit to read command delay Power down exit time Average Refresh interval time Control and Address input pulse width DQ & DM input pulse width (for each input) 100K 15.6 - 0.9 0.4 0.72 0 0.25 0.4 0.4 0.4 0.7 0.7 0.4 0.4 tCLMIN or tCHMIN tHP - tQHS 55 70 40 15 15 2 3 2 tWR + tRP 200 tCK + tIS 2.2 1.75 0.4 1.1 0.6 1.25 0.6 - tHP 0.9 0.4 0.72 0 0.25 0.4 0.4 0.4 0.7 0.7 0.4 0.4 tCLMIN or tCHMIN tHP - tQHS 55 60 40 15 15 3 3 2 tWR + tRP 200 tCK + tIS 2.2 1.75 100K 15.6 - ns ns ns ns ns ns tCK tCK tCK tCK tCK ns µs ns ns tHZ Data-out high-impedance window from CK/ CK - 0.7 - 0.7 ns tLZ Data-out low-impedance window from CK/ CK -0.7 0.7 -0.7 0.7 ns tQHS Data Hold Skew Factor Output data valid window Exit Self-Refresh to non-Read command CAS# to CAS# Delay time tQH - tDQSQ 75 1 0.45 - tQH - tDQSQ 75 1 0.5 - ns ns ns tCK DVW tXSNR tCCD Etron Confidential CL = 2 CL = 2.5 CL = 3 12 Max. 10 0.55 0.55 Min. 7.5 6 5 0.45 0.45 Max. 12 12 7.5 0.55 0.55 Unit Min. 4 0.45 0.45 - Rev 1.0 ns ns ns tCK tCK July /2012 EtronTech EM6A9320BIB Table 19. Recommended A.C. Operating Conditions (TA = -40~85 °C, VDD=2.5V ± 0.2V) Parameter -4I/5I Symbol Min. Max. Unit Input High Voltage (AC) VIH (AC) VREF + 0.31 - V Input Low Voltage (AC) VIL (AC) - VREF – 0.31 V Input Different Voltage, CK and CK inputs VID (AC) 0.7 VDDQ + 0.6 V 0.5*VDDQ-0.2 0.5*VDDQ+0.2 V Input Crossing Point Voltage, CK and CK inputs VIX (AC) Note: 1. All voltages are referenced to VSS. 2. These parameters depend on the cycle rate and these values are measured by the cycle rate under the minimum value of tCK and tRC. Input signals are changed one time during tCK. 3. Power-up sequence is described in Note 5. 4. A.C. Test Conditions Table 20. SSTL_2 Interface Reference Level of Output Signals (VREF) 0.5 * VDDQ Output Load Reference to the Test Load Input Signal Levels VREF+0.31 V / VREF-0.31 V Input Signals Slew Rate 1 V/ns Reference Level of Input Signals 0.5 * VDDQ Figure 3. SSTL_2 A.C. Test Load 0.5 * VDDQ 50Ω DQ, DQS Z0=50Ω Etron Confidential 13 30pF Rev 1.0 July /2012 EtronTech EM6A9320BIB 5. Power up Sequence Power up must be performed in the following sequence. 1) Apply power to VDD before or at the same time as VDDQ, VTT and VREF when all input signals are held "NOP" state and maintain CKE “LOW”. 2) Start clock and maintain stable condition for minimum 200us. 3) Issue a “NOP” command and keep CKE “HIGH” 4) Issue a “Precharge All” command. 5) Issue EMRS – enable DLL. 6) Issue MRS – reset DLL. (An additional 200 clock cycles are required to lock the DLL). 7) Precharge all banks of the device. 8) Issue two or more Auto Refresh commands. 9) Issue MRS – with A8 to low to initialize the mode register. Etron Confidential 14 Rev 1.0 July /2012 EtronTech EM6A9320BIB Timing Waveforms Figure 4. Activating a Specific Row in a Specific Bank CK CK CKE HIGH CS RAS CAS WE Address RA BA0,1 BA RA=Row Address BA=Bank Address Don’t Care Etron Confidential 15 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 5. tRCD and tRRD Definition CK CK COMMAND ACT Address Row Row Col BA0,BA1 Bank A Bank B Bank B NOP NOP ACT tRRD NOP NOP RD/WR NOP tRCD Don’t Care Figure 6. READ Command CK CK CKE HIGH CS RAS CAS WE A0 ~ A7 CA EN AP A8 DIS AP BA BA0,1 CA=Column Address BA=Bank Address EN AP=Enable Autoprecharge DIS AP=Disable Autoprecharge Don’t Care Etron Confidential 16 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 7. Read Burst Required CAS Latencies (CL=2) CK CK COMMAND READ ADDRESS Bank A, Col n NOP NOP NOP NOP NOP CL=2 DQS DO n DQ DO n=Data Out from column n Burst Length=4 3 subsequent elements of Data Out appear in the programmed order following DO n Don’t Care Read Burst Required CAS Latencies (CL=2.5) CK CK COMMAND READ ADDRESS Bank A, Col n NOP NOP NOP NOP NOP CL=2.5 DQS DO n DQ DO n=Data Out from column n Burst Length=4 3 subsequent elements of Data Out appear in the programmed order following DO n Don’t Care Etron Confidential 17 Rev 1.0 July /2012 EtronTech EM6A9320BIB Read Burst Required CAS Latencies (CL=3) CK CK COMMAND READ ADDRESS Bank A, Col n NOP NOP NOP NOP NOP CL=3 DQS DO n DQ DO n=Data Out from column n Burst Length=4 3 subsequent elements of Data Out appear in the programmed order following DO n Don’t Care Etron Confidential 18 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 8. Consecutive Read Bursts Required CAS Latencies (CL=2) CK CK COMMAND READ NOP NOP NOP NOP Bank, Col o Bank, Col n ADDRESS READ CL=2 DQS DO n DQ DO o DO n (or o)=Data Out from column n (or column o) Burst Length=4 or 8 (if 4, the bursts are concatenated; if 8, the second burst interrupts the first) 3 subsequent elements of Data Out appear in the programmed order following DO n 3 (or 7) subsequent elements of Data Out appear in the programmed order following DO o Read commands shown must be to the same device Don’t Care Etron Confidential 19 Rev 1.0 July /2012 EtronTech EM6A9320BIB Consecutive Read Bursts Required CAS Latencies (CL=2.5) CK CK COMMAND READ NOP NOP NOP NOP Bank, Col o Bank, Col n ADDRESS READ CL=2.5 DQS DO n DQ DO o DO n (or o)=Data Out from column n (or column o) Burst Length=4 or 8 (if 4, the bursts are concatenated; if 8, the second burst interrupts the first) 3 subsequent elements of Data Out appear in the programmed order following DO n 3 (or 7) subsequent elements of Data Out appear in the programmed order following DO o Read commands shown must be to the same device Don’t Care Etron Confidential 20 Rev 1.0 July /2012 EtronTech EM6A9320BIB Consecutive Read Bursts Required CAS Latencies (CL=3) CK CK READ COMMAND NOP Bank, Col n ADDRESS READ NOP NOP NOP Bank, Col o CL=3 DQS DO n DQ DO o DO n (or o)=Data Out from column n (or column o) Burst Length=4 or 8 (if 4, the bursts are concatenated; if 8, the second burst interrupts the first) 3 subsequent elements of Data Out appear in the programmed order following DO n 3 (or 7) subsequent elements of Data Out appear in the programmed order following DO o Read commands shown must be to the same device Don’t Care Etron Confidential 21 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 9. Non-Consecutive Read Bursts Required CAS Latencies (CL=2) CK CK READ COMMAND NOP NOP READ Bank, Col o Bank, Col n ADDRESS NOP NOP CL=2 DQS DO n DQ DO o DO n (or o)=Data Out from column n (or column o) Burst Length=4 3 subsequent elements of Data Out appear in the programmed order following DO n (and following DO o) Don’t Care Non-Consecutive Read Bursts Required CAS Latencies (CL=2.5) CK CK COMMAND READ NOP NOP READ NOP NOP Bank, Col o Bank, Col n ADDRESS NOP CL=2.5 DQS DO n DQ DO o DO n (or o)=Data Out from column n (or column o) Burst Length=4 3 subsequent elements of Data Out appear in the programmed order following DO n (and following DO o) Don’t Care Etron Confidential 22 Rev 1.0 July /2012 EtronTech EM6A9320BIB Non-Consecutive Read Bursts Required CAS Latencies (CL=3) CK CK COMMAND ADDRESS READ NOP NOP READ NOP NOP NOP Bank, Col o Bank, Col n CL=3 DQS DO n DQ DO o DO n (or o)=Data Out from column n (or column o) Burst Length=4 3 subsequent elements of Data Out appear in the programmed order following DO n (and following DO o) Don’t Care Etron Confidential 23 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 10. Random Read Accesses Required CAS Latencies (CL=2) CK CK COMMAND ADDRESS READ READ READ READ Bank, Col n Bank, Col o Bank, Col p Bank, Col q NOP NOP CL=2 DQS DO n' DO n DQ DO o' DO o DO p DO p' DO q DO n, etc. =Data Out from column n, etc. n', etc. =the next Data Out following DO n, etc. according to the programmed burst order Burst Length=2,4 or 8 in cases shown. If burst of 4 or 8, the burst is interrupted Reads are to active rows in any banks Don’t Care Random Read Accesses Required CAS Latencies (CL=2.5) CK CK COMMAND ADDRESS READ READ READ READ Bank, Col n Bank, Col o Bank, Col p Bank, Col q NOP NOP CL=2.5 DQS DO n DQ DO n' DO o DO o' DO p DO p' DO n, etc. =Data Out from column n, etc. n', etc. =the next Data Out following DO n, etc. according to the programmed burst order Burst Length=2,4 or 8 in cases shown. If burst of 4 or 8, the burst is interrupted Reads are to active rows in any banks Don’t Care Etron Confidential 24 Rev 1.0 July /2012 EtronTech EM6A9320BIB Random Read Accesses Required CAS Latencies (CL=3) CK CK COMMAND READ READ READ READ Bank, Col n Bank, Col o Bank, Col p Bank, Col q ADDRESS NOP NOP CL=3 DQS DO n DQ DO n' DO o DO o' DO p DO n, etc. =Data Out from column n, etc. n', etc. =the next Data Out following DO n, etc. according to the programmed burst order Burst Length=2,4 or 8 in cases shown. If burst of 4 or 8, the burst is interrupted Reads are to active rows in any banks Don’t Care Etron Confidential 25 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 11. Terminating a Read Burst Required CAS Latencies (CL=2) CK CK COMMAND READ ADDRESS Bank A, Col n NOP BST NOP NOP NOP CL=2 DQS DO n DQ DO n = Data Out from column n Cases shown are bursts of 8 terminated after 4 data elements 3 subsequent elements of Data Out appear in the programmed order following DO n Don’t Care Terminating a Read Burst Required CAS Latencies (CL=2.5) CK CK COMMAND READ ADDRESS Bank A, Col n NOP BST NOP NOP NOP CL=2.5 DQS DO n DQ DO n = Data Out from column n Cases shown are bursts of 8 terminated after 4 data elements 3 subsequent elements of Data Out appear in the programmed order following DO n Don’t Care Etron Confidential 26 Rev 1.0 July /2012 EtronTech EM6A9320BIB Terminating a Read Burst Required CAS Latencies (CL=3) CK CK COMMAND READ ADDRESS Bank A, Col n NOP BST NOP NOP NOP CL=3 DQS DO n DQ DO n = Data Out from column n Cases shown are bursts of 8 terminated after 4 data elements 3 subsequent elements of Data Out appear in the programmed order following DO n Don’t Care Etron Confidential 27 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 12. Read to Write Required CAS Latencies (CL=2) CK CK COMMAND READ BST NOP NOP Bank, Col o Bank, Col n ADDRESS NOP WRITE tDQSS min CL=2 DQS DO n DQ DI o DM DO n (or o)= Data Out from column n (or column o) Burst Length= 4 in the cases shown (applies for bursts of 8 as well; if burst length is 2, the BST command shown can be NOP) 1 subsequent element of Data Out appears in the programmed order following DO n Data in elements are applied following DI o in the programmed order Don’t Care Etron Confidential 28 Rev 1.0 July /2012 EtronTech EM6A9320BIB Read to Write Required CAS Latencies (CL=2.5) CK CK COMMAND READ BST NOP NOP Bank, Col o Bank, Col n ADDRESS NOP WRITE tDQSS min CL=2.5 DQS DO n DQ DI o DM DO n (or o)= Data Out from column n (or column o) Burst Length= 4 in the cases shown (applies for bursts of 8 as well; if burst length is 2, the BST command shown can be NOP) 1 subsequent element of Data Out appears in the programmed order following DO n Data in elements are applied following DI o in the programmed order Don’t Care Etron Confidential 29 Rev 1.0 July /2012 EtronTech EM6A9320BIB Read to Write Required CAS Latencies (CL=3) CK CK COMMAND READ BST NOP NOP Bank, Col o Bank, Col n ADDRESS NOP WRITE tDQSS min CL=3 DQS DO n DQ DI o DM DO n (or o)= Data Out from column n (or column o) Burst Length= 4 in the cases shown (applies for bursts of 8 as well; if burst length is 2, the BST command shown can be NOP) 1 subsequent element of Data Out appears in the programmed order following DO n Data in elements are applied following DI o in the programmed order Don’t Care Etron Confidential 30 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 13. Read to Precharge Required CAS Latencies (CL=2) CK CK COMMAND READ NOP PRE NOP NOP ACT tRP Bank A, Col n ADDRESS Bank (a or all) Bank A, Row CL=2 DQS DO n DQ DO n = Data Out from column n Cases shown are either uninterrupted bursts of 4, or interrupted bursts of 8 3 subsequent elements of Data Out appear in the programmed order following DO n Precharge may be applied at (BL/2) tCK after the READ command Note that Precharge may not be issued before tRAS ns after the ACTIVE command for applicable banks The Active command may be applied if tRC has been met Don’t Care Etron Confidential 31 Rev 1.0 July /2012 EtronTech EM6A9320BIB Read to Precharge Required CAS Latencies (CL=2.5) CK CK COMMAND READ NOP PRE NOP NOP ACT tRP Bank A, Col n ADDRESS Bank (a or all) Bank A, Row CL=2.5 DQS DO n DQ DO n = Data Out from column n Cases shown are either uninterrupted bursts of 4, or interrupted bursts of 8 3 subsequent elements of Data Out appear in the programmed order following DO n Precharge may be applied at (BL/2) tCK after the READ command Note that Precharge may not be issued before tRAS ns after the ACTIVE command for applicable banks The Active command may be applied if tRC has been met Don’t Care Etron Confidential 32 Rev 1.0 July /2012 EtronTech EM6A9320BIB Read to Precharge Required CAS Latencies (CL=3) CK CK COMMAND READ NOP PRE NOP NOP ACT tRP Bank A, Col n ADDRESS Bank (a or all) Bank A, Row CL=3 DQS DO n DQ DO n = Data Out from column n Cases shown are either uninterrupted bursts of 4, or interrupted bursts of 8 3 subsequent elements of Data Out appear in the programmed order following DO n Precharge may be applied at (BL/2) tCK after the READ command Note that Precharge may not be issued before tRAS ns after the ACTIVE command for applicable banks The Active command may be applied if tRC has been met Etron Confidential 33 Don’t Care Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 14. Write Command CK CK CKE HIGH CS RAS CAS WE A0 ~ A7 CA EN AP A8 DIS AP BA0,1 BA CA=Column Address BA=Bank Address EN AP=Enable Autoprecharge DIS AP=Disable Autoprecharge Don’t Care Etron Confidential 34 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 15. Write Max DQSS T0 T1 T2 T3 T4 T5 T6 T7 CK CK COMMAND WRITE ADDRESS Bank A, Col n NOP NOP NOP tDQSS max DQS DI n DQ DM DI n = Data In for column n 3 subsequent elements of Data In are applied in the programmed order following DI n A non-interrupted burst of 4 is shown A8 is LOW with the WRITE command (AUTO PRECHARGE disabled) Don’t Care Etron Confidential 35 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 16. Write Min DQSS T0 T1 T2 T3 T4 T5 T6 CK CK COMMAND NOP WRITE NOP NOP Bank A, Col n tDQSS min ADDRESS DQS DI n DQ DM DI n = Data In for column n 3 subsequent elements of Data In are applied in the programmed order following DI n A non-interrupted burst of 4 is shown A8 is LOW with the WRITE command (AUTO PRECHARGE disabled) Don’t Care Etron Confidential 36 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 17. Write Burst Nom, Min, and Max tDQSS T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 CK CK COMMAND NOP WRITE NOP NOP NOP NOP Bank , Col n ADDRESS tDQSS (nom) DQS DI n DQ DM tDQSS (min) DQS DI n DQ DM tDQSS (max) DQS DI n DQ DM DI n = Data In for column n 3 subsequent elements of Data are applied in the programmed order following DI n A non-interrupted burst of 4 is shown A8 is LOW with the WRITE command (AUTO PRECHARGE disabled) DM=DM0 ~ DM3 Don’t Care Etron Confidential 37 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 18. Write to Write Max tDQSS T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 CK CK COMMAND WRITE NOP NOP NOP NOP Bank , Col o Bank , Col n ADDRESS WRITE tDQSS (max) DQS DI n DQ DI o DM DI n , etc. = Data In for column n,etc. 3 subsequent elements of Data In are applied in the programmed order following DI n 3 subsequent elements of Data In are applied in the programmed order following DI o Non-interrupted bursts of 4 are shown DM= DM0 ~ DM3 Don’t Care Etron Confidential 38 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 19. Write to Write Max tDQSS, Non Consecutive T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 CK CK COMMAND WRITE NOP NOP Bank Col n ADDRESS WRITE NOP NOP Bank Col o tDQSS (max) DQS DI n DQ DI o DM DI n, etc. = Data In for column n, etc. 3 subsequent elements of Data In are applied in the programmed order following DI n 3 subsequent elements of Data In are applied in the programmed order following DI o Non-interrupted bursts of 4 are shown DM= DM0 ~ DM3 Don’t Care Etron Confidential 39 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 20. Random Write Cycles Max tDQSS Etron Confidential 40 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 21. Write to Read Max tDQSS Non Interrupting T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 CK CK COMMAND WRITE NOP NOP NOP READ NOP NOP tWTR ADDRESS Bank Col o Bank Col n CL=3 tDQSS (max) DQS DI n DQ DM DI n, etc. = Data In for column n, etc. 1 subsequent elements of Data In are applied in the programmed order following DI n A non-interrupted burst of 2 is shown tWTR is referenced from the first positive CK edge after the last Data In Pair A8 is LOW with the WRITE command (AUTO PRECHARGE is disabled) The READ and WRITE commands are to the same devices but not necessarily to the same bank DM= DM0 ~ DM3 Don’t Care Etron Confidential 41 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 22. Write to Read Max tDQSS Interrupting T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 CK CK COMMAND WRITE NOP NOP NOP READ NOP tWTR Bank Col o Bank Col n ADDRESS CL=3 tDQSS (max) DQS DI n DQ DM DI n, etc. = Data In for column n, etc. 1 subsequent elements of Data In are applied in the programmed order following DI n An interrupted burst of 8 is shown, 2 data elements are written tWTR is referenced from the first positive CK edge after the last Data In Pair A8 is LOW with the WRITE command (AUTO PRECHARGE is disabled) The READ and WRITE commands are to the same devices but not necessarily to the same bank DM= DM0 ~ DM3 Don’t Care Etron Confidential 42 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 23. Write to Read Max tDQSS, ODD Number of Data, Interrupting T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 CK CK COMMAND WRITE NOP NOP NOP READ NOP tWTR ADDRESS Bank Col o Bank Col n CL=3 tDQSS (max) DQS DI n DQ DM DI n = Data In for column n An interrupted burst of 8 is shown, 1 data elements are written tWTR is referenced from the first positive CK edge after the last Data In Pair (not the last desired Data In element) A8 is LOW with the WRITE command (AUTO PRECHARGE is disabled) The READ and WRITE commands are to the same devices but not necessarily to the same bank DM= DM0 ~ DM3 Don’t Care Etron Confidential 43 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 24. Write to Precharge Max tDQSS, NON- Interrupting T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 CK CK COMMAND WRITE ADDRESS Bank a, Col n NOP NOP NOP NOP PRE tWR Bank (a or al) tRP tDQSS (max) DQS DI n DQ DM DI n = Data In for column n 1 subsequent elements of Data In are applied in the programmed order following DI n A non-interrupted burst of 2 is shown tWR is referenced from the first positive CK edge after the last Data In Pair A8 is LOW with the WRITE command (AUTO PRECHARGE is disabled) DM= DM0 ~ DM3 Don’t Care Etron Confidential 44 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 25. Write to Precharge Max tDQSS, Interrupting T0 T1 T2 T3 T4 T5 T6 T8 T7 T9 T10 T11 CK CK COMMAND WRITE ADDRESS Bank a, Col n NOP NOP NOP PRE NOP tWR Bank (a or all) tDQSS (max) tRP *2 DQS DI n DQ DM *1 *1 *1 *1 DI n = Data In for column n An interrupted burst of 4 or 8 is shown, 2 data elements are written tWR is referenced from the first positive CK edge after the last Data In Pair A8 is LOW with the WRITE command (AUTO PRECHARGE is disabled) *1 = can be don't care for programmed burst length of 4 *2 = for programmed burst length of 4, DQS becomes don't care at this point DM= DM0 ~ DM3 Don’t Care Etron Confidential 45 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 26. Write to Precharge Max tDQSS ODD Number of Data Interrupting T0 T1 T2 T3 T4 T5 T6 T8 T7 T9 T10 T11 CK CK COMMAND WRITE ADDRESS Bank a, Col n NOP NOP NOP NOP PRE tWR Bank (a or all) tDQSS (max) tRP *2 DQS DI n DQ DM *1 *1 *1 *1 DI n = Data In for column n An interrupted burst of 4 or 8 is shown, 1 data element is written tWR is referenced from the first positive CK edge after the last Data In Pair A8 is LOW with the WRITE command (AUTO PRECHARGE is disabled) *1 = can be don't care for programmed burst length of 4 *2 = for programmed burst length of 4, DQS becomes don't care at this point DM= DM0 ~ DM3 Don’t Care Etron Confidential 46 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 27. Precharge Command CK CK CKE HIGH CS RAS CAS WE A0-A7, A9-A11 ALL BANKS A8 ONE BANK BA0,1 BA BA= Bank Address (if A8 is LOW, otherwise don't care) Don’t Care Etron Confidential 47 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 28. Power-Down T0 T1 T2 T3 T4 Tn Tn+3 Tn+4 Tn+5 Tn+6 Tn+1 Tn+2 CK CK tIS tIS CKE COMMAND NOP NOP VALID No column access in progress VALID Exit power-down mode Enter power-down mode Don’t Care Figure 29. Clock Frequency Change in Precharge T0 T1 T2 T4 Tx Tx+1 Ty Ty+1 Ty+2 Ty+3 Ty+4 Tz CK CK CMD CKE NOP NOP NOP Frequency Change Occurs here DLL RESET NOP NOP Valid tIS tRP Minmum 2 clocks Required before Changing frequency Etron Confidential Stable new clock Before power down exit 48 200 Clocks Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 30. Data input (Write) Timing tDQSH tDQSL DQS tDS DI n DQ tDH tDS DM tDH DI n = Data In for column n Burst Length = 4 in the case shown 3 subsequent elements of Data In are applied in the programmed order following DI n Don’t Care Figure 31. Data Output (Read) Timing tCH tCL CK CK DQS DQ tDQSQ tDQSQ max max tQH tQH Burst Length = 4 in the case shown Etron Confidential 49 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 32. Initialize and Mode Register Sets VDD VDDQ tVDT>=0 VTT (system*) tCK tCH tCL VREF CK CK tIS tIH CKE LVCMOS LOW LEVEL tIS tIH NOP COMMAND PRE MRS EMRS PRE AR AR MRS ACT CODE RA CODE RA BA0=L BA1=L BA DM tIS tIH A0-A7, A9-A11 CODE ALL BANKS A8 tIS tIH CODE tIS tIH ALL BANKS CODE CODE tIS tIH tIS tIH BA0=H BA1=L BA0,BA1 BA0=L BA1=L High-Z DQS High-Z DQ T=200µs **tMRD **tMRD Extended mode Register set Power-up: VDD and CLK stable tRP tRFC tRFC **tMRD 200 cycles of CK** Load Mode Register, Reset DLL (with A8=H) Load Mode Register, (with A8=L) Don’t Care *=VTT is not applied directly to the device, however tVTD must be greater than or equal to zero to avoid device latch-up. ** = tMRD is required before any command can be applied, and 200 cycles of CK are required before any executable command can be applied the two auto Refresh commands may be moved to follow the first MRS but precede the second PRECHARGE ALL command. Etron Confidential 50 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 33. Power Down Mode tCK tCH tCL CK CK tIS tIH tIS tIS CKE tIS tIH COMMAND VALID* NOP NOP VALID tIS tIH ADDR VALID VALID DQS DQ DM Enter power-down mode Exit power-down mode No column accesses are allowed to be in progress at the time Power-Down is entered *=If this command is a PRECHARGE ALL (or if the device is already in the idle state) then the Power-Down mode shown is Precharge Power Down. If this command is an ACTIVE (or if at least one row is already active) then the Power-Down mode shown is active Power Down. Don’t Care Etron Confidential 51 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 34. Auto Refresh Mode tCK tCH tCL CK CK tIS tIH CKE VALID VALID tIS tIH NOP COMMAND PRE NOP NOP AR NOP AR NOP NOP ACT A0-A7 RA A9-A11 RA ALL BANKS A8 RA ONE BANKS tIS BA0,BA1 tIH BA *Bank(s) DQS DQ DM tRP *= tRFC tRFC Don't Care , if A8 is HIGH at this point; A8 must be HIGH if more than one bank is active (i.e., must precharge all active banks) PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address, AR = AUTOREFRESH NOP commands are shown for ease of illustration; other valid commands may be possible after tRFC DM, DQ and DQS signals are all Don't Care /High-Z for operations shown Don’t Care Etron Confidential 52 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 35. Self Refresh Mode tCK tCH Clock must be stable before Exiting Self Refresh mode tCL CK CK tIS tIH tIS tIS CKE tIS tIH COMMAND NOP NOP AR VALID tIS tIH VALID ADDR DQS DQ DM tRP* tXSNR/ tXSRD** Enter Self Refresh mode Exit Self Refresh mode * = Device must be in the All banks idle state prior to entering Self Refresh mode ** = tXSNR is required before any non-READ command can be applied, and tXSRD (200 cycles of CK) is required before a READ command can be applied. Don’t Care Etron Confidential 53 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 36. Read without Auto Precharge tCK tCH tCL CK CK tIH tIS tIH CKE VALID VALID VALID NOP NOP NOP tIS tIH NOP COMMAND READ PRE NOP NOP NOP ACT tIS tIH Col n ADDRESS tIS RA tIH ALL BANKS RA A8 DIS AP ONE BANKS tIS tIH Bank X BA0,BA1 Bank X *Bank X CL=3 tRP DM Case 1: tAC/tDQSCK=min tDQSCK min tRPRE tRPST DQS tLZ min DQ DO n tLZ tAC min min Case 2: tAC/tDQSCK=max tDQSCK max tRPRE tRPST DQS tLZ max DQ tLZ max tHZ DO n max tAC max DO n = Data Out from column n Burst Length = 4 in the case shown 3 subsequent elements of Data Out are provided in the programmed order following DO n DIS AP = Disable Autoprecharge * = Don't Care , if A8 is HIGH at this point PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address, AR = AUTOREFRESH NOP commands are shown for ease of illustration; other commands may be valid at these times Don’t Care Precharge may not be issued before tRAS ns after the ACTIVE command for applicable banks Etron Confidential 54 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 37. Read with Auto Precharge tCK tCH tCL CK CK tIH tIS tIH CKE VALID VALID VALID NOP NOP NOP tIS tIH NOP COMMAND READ NOP NOP NOP NOP ACT tIS tIH Col n A0-A7 RA RA A9-A11 EN AP RA A8 tIS tIH tIS tIH Bank X BA0,BA1 Bank X CL=3 tRP DM Case 1: tAC/tDQSCK=min tDQSCK min tRPST tRPRE DQS tLZ min DO n DQ tLZ tAC min min Case 2: tAC/tDQSCK=max tDQSCK max tRPST tRPRE DQS tLZ max tHZ max DO n DQ tLZ max tAC max DO n = Data Out from column n Burst Length = 4 in the case shown 3 subsequent elements of Data Out are provided in the programmed order following DO n EN AP = Enable Autoprecharge ACT = ACTIVE, RA = Row Address NOP commands are shown for ease of illustration; other commands may be valid at these times The READ command may not be issued until tRAP has been satisfied. If Fast Autoprecharge is supported, tRAP = tRCD, else the READ may not be issued prior to tRASmin (BL*tCK/2) Don’t Care Etron Confidential 55 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 38. Bank Read Access tCK tCH tCL CK CK tIS tIH CKE tIS tIH COMMAND NOP ACT NOP NOP NOP READ NOP PRE NOP NOP ACT tIS tIH A0-A7 RA A9-A11 RA Col n RA tIS A8 RA tIH ALL BANKS RA RA DIS AP ONE BANKS Bank X *Bank X tIS tIH Bank X BA0,BA1 Bank X tRC tRAS tRCD tRP CL=3 DM Case 1: tAC/tDQSCK=min tDQSCK min tRPRE tRPST DQS tLZ DO n min DQ tLZ tAC tDQSCK min Case 2: tAC/tDQSCK=max min max tRPRE DQS tHZ tLZ max max DO n DQ tLZ DO n = Data Out from column n Burst Length = 4 in the case shown 3 subsequent elements of Data Out are provided in the programmed order following DO n tRPST max tAC max DIS AP = Disable Autoprecharge *= Don't Care , if A8 is HIGH at this point PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address NOP commands are shown for ease of illustration; other commands may be valid at these times Note that tRCD > tRCD MIN so that the same timing applies if Autoprecharge is enabled (in which case tRAS would be limiting) Etron Confidential 56 Don’t Care Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 39. Write without Auto Precharge tCK tCH tCL CK CK tIH tIS tIH CKE VALID tIS tIH NOP COMMAND NOP NOP NOP WRITE NOP PRE NOP NOP ACT tIS tIH RA Col n A0-A7 RA A9-A11 tIS tIH ALL BANKS RA A8 ONE BANKS DIS AP tIS tIH Bank X BA0,BA1 Case 1: tDQSS=min tDQSS BA *Bank X tDSH tDQSH tRP tDSH tWR tWPST DQS tDQSL tWPRES tWPRE DI n DQ DM tDSS Case 2: tDQSS=max tDQSS tDQSH tDSS tWPST DQS tWPRES tDQSL tWPRE DI n DQ DM DI n = Data In from column n Burst Length = 4 in the case shown 3 subsequent elements of Data In are provided in the programmed order following DI n DIS AP = Disable Autoprecharge *= Don't Care , if A8 is HIGH at this point PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address, AR = AUTOREFRESH NOP commands are shown for ease of illustration; other commands may be valid at these times Although tDQSS is drawn only for the first DQS rising edge, each rising edge of DQS must fall within the + 25% window of the corresponding positive clock edge Precharge may not be issued before tRAS ns after the ACTIVE command for applicable banks Etron Confidential 57 Rev 1.0 Don’t Care July /2012 EtronTech EM6A9320BIB Figure 40. Write with Auto Precharge tCK tCH tCL CK CK tIS tIH CKE VALID VALID VALID NOP NOP NOP tIS tIH COMMAND NOP WRITE NOP NOP NOP NOP ACT tIS tIH RA Col n A0-A7 RA A9-A11 DIS AP RA A8 tIS tIH Bank X BA0,BA1 BA tDAL Case 1: tDQSS=min tDQSS tDSH tDQSH tDSH tWPST DQS tWPRES tDQSL tWPRE DI n DQ DM Case 2: tDQSS=max tDQSS tDSS tDQSH tDSS tWPST DQS tWPRES tDQSL tWPRE DI n DQ DM DI n = Data In from column n Burst Length = 4 in the case shown 3 subsequent elements of Data Out are provided in the programmed order following DI n EN AP = Enable Autoprecharge ACT = ACTIVE, RA = Row Address, BA = Bank Address NOP commands are shown for ease of illustration; other commands may be valid at these times Although tDQSS is drawn only for the first DQS rising edge, each rising edge of DQS must fall within the + 25% window of the corresponding positive clock edge Don’t Care Etron Confidential 58 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 41. Bank Write Access tCK tCH tCL CK CK tIS tIH CKE tIS tIH NOP COMMAND ACT NOP NOP WRITE NOP NOP NOP NOP PRE tIS tIH A0-A7 RA A9-A11 RA A8 RA Col n tIS tIH ALL BANKS DIS AP ONE BANK tIS tIH Bank X BA0,BA1 Bank X *Bank X tRAS tRCD Case 1: tDQSS=min tWR tDQSS tDSH tDQSH tDSH tWPST DQS tWPRES tWPRE tDQSL DI n DQ DM tDSS Case 2: tDQSS=max tDSS tDQSH tDQSS tWPST DQS tWPRES tWPRE tDQSL DI n DQ DM DI n = Data In from column n Burst Length = 4 in the case shown 3 subsequent elements of Data Out are provided in the programmed order following DI n DIS AP = Disable Autoprecharge *= Don't Care , if A8 is HIGH at this point PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address NOP commands are shown for ease of illustration; other commands may be valid at these times Although tDQSS is drawn only for the first DQS rising edge, each rising edge of DQS must fall within the + 25% window of the corresponding positive clock edge Don’t Care Precharge may not be issued before tRAS ns after the ACTIVE command for applicable banks Etron Confidential 59 Rev 1.0 July /2012 EtronTech EM6A9320BIB Figure 42. Write DM Operation tCK tCH tCL CK CK tIS tIH CKE VALID tIS tIH NOP COMMAND WRITE NOP NOP NOP NOP PRE NOP NOP ACT tIS tIH RA Col n A0-A7 RA A9-A11 tIS tIH ALL BANKS RA A8 ONE BANKS DIS AP tIS tIH Bank X BA0,BA1 Case 1: tDQSS=min BA *Bank X tDQSS tDSH tDQSH tRP tDSH tWR tWPST DQS tDQSL tWPRES tWPRE DI n DQ DM tDSS Case 2: tDQSS=max tDQSS tDSS tDQSH tWPST DQS tWPRES tDQSL tWPRE DI n DQ DM DI n = Data In from column n Burst Length = 4 in the case shown 3 subsequent elements of Data In are provided in the programmed order following DI n DIS AP = Disable Autoprecharge *= Don't Care , if A8 is HIGH at this point PRE = PRECHARGE, ACT = ACTIVE, RA = Row Address, BA = Bank Address NOP commands are shown for ease of illustration; other commands may be valid at these times Although tDQSS is drawn only for the first DQS rising edge, each rising edge of DQS must fall within the + 25% window of the corresponding positive clock edge Precharge may not be issued before tRAS ns after the ACTIVE command for applicable banks Etron Confidential 60 Rev 1.0 Don’t Care July /2012 EtronTech EM6A9320BIB Figure 43. 144 ball LFBGA Package Outline Drawing Information Units: mm PIN #1 Top View "A" Bottom View Side View DETAIL : "A" Symbol A A1 A2 D E D1 E1 e b Etron Confidential Dimension in inch Dimension in mm Min Nom Max Min Nom Max --0.055 --1.40 0.012 0.014 0.016 0.30 0.35 0.40 0.036 0.038 0.040 0.91 0.96 1.01 0.469 0.472 0.476 11.90 12.00 12.10 0.469 0.472 0.476 11.90 12.00 12.10 -0.346 --8.80 --0.346 --8.80 --0.031 --0.80 -0.016 0.018 0.020 0.40 0.45 0.50 61 Rev 1.0 July /2012