ACE515A Technology 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Description ACE515A series are 300mA, positive voltage regulator ICs fabricated by CMOS process. Each of these ICs is equipped with a voltage reference, an error amplifier, a resistor network for setting output voltage, a chip enable circuit, a current limit circuit and OTSD (over temperature shut down) circuit to prevent the IC from over current and over temperature. The ACE515A series have features of high ripple rejection, low dropout voltage, low noise, high output voltage accuracy and low current consumption which make them ideal for use in various battery-powered apparatus. The ACE515A have 1.8V, 2.5V, 2.8V, 3.0V, 3.3V, 4.15V and 4.2V fixed voltage versions. These ICs are available in tiny SC-70-5 and SC-82 packages as well as industry standard SOT-23-3 and SOT-23-5 packages. Features • • • • • • • • • Excellent Ripple Rejection: 70dB Typical (1.8V Version) Low Dropout Voltage: 65mV (IOUT=100mA, 3.3V Version) Low Standby Current: 0.01μA Typical Low Quiescent Current: 60μA Typical Extremely Low Noise: 50μVrms Typical Maximum Output Current: 300mA (Min.) High Output Voltage Accuracy: ±2% Compatible with Low ESR Ceramic Capacitor Excellent Line/ Load Regulation Application • • • • • • CDMA/ GSM Cellular Handsets Battery-powered Equipments Laptops, Palmtops, Notebook Computers Hand-held Instruments PCMCIA Cards Portable Information Appliances VER 1.2 1 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Absolute Maximum Ratings Parameter Symbol Max Unit Input voltage VIN 6.5 V Enable Input Voltage VCE -0.3 to VIN+0.3 V Output Current IOUT 450 mA Junction Temperature TJ 150 ℃ Storage Temperature Range TSTG -65 to 150 ℃ Lead Temperature (Soldering, 10sec) Thermal Resistance SOT-23-3 SOT-23-5 SC-70-5 SC-82 ESD (Human Body Model) TLEAD 260 ℃ ESD 200 200 300 300 6000 ESD (Machine Model) ESD 400 θJA ℃/W V V Note 1: Stresses greater than those listed under “ Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute Maximum Ratings” for extended periods may affect device reliability. Packaging Type SOT-23-5 /SC-70-5 5 1 SOT-23-3 4 2 SC-82 3 3 1 2 Pin Number Symbol SOT-23-5 / SC-70-5 SOT-23-3 SC-82 1 3 4 VIN 2 1 2 GND 3 4 5 2 1 CE 3 NC VOUT 4 3 1 2 Function Input voltage Ground Active high enable input pin, Logic high=enable, logic low=shutdown No connection Regulated output voltage VER 1.2 2 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Ordering information Selection Guide ACE515A XX XX + H Halogen - free Pb - free BN: SOT-23-5 BM: SOT-23-3 HN: SC-70-5 QM: SC-82 Output Voltage： 1.5V/2.8V…..4.2V Functional Block Diagram SOT-23-3 A(B) A SOT-23-5 / SC-70-5 B SC-82 Recommended Work Conditions Item Input Voltage Operating Ambient Temperature Symbol Min Max Unit VIN VOUT+0.5V 6 V TA -40 85 ℃ VER 1.2 3 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Electrical Characteristics ACE515A-1.8 Electrical Characteristics (VIN=2.8V, TA=25℃, CIN=1μF, Bold typeface applies over -40℃≦TJ≦85℃, unless otherwise specified.) Parameter Symbol Output Voltage VOUT Input Voltage Maximum Output Current VIN IOUT(Max.) Load Regulation VRLOAD Line Regulation VRLINE Dropout Voltage VDROP Quiescent Current Standby Current Power Supply Rejection Ratio Output Voltage Temperature Coefficient Short Current Limit RMS Output Noise CE “High” Voltage CE “Low” Voltage Thermal Shutdown Thermal Shutdown Hysteresis IQ ISTD PSRR (ΔVOUT / ΔIOUT)/ ΔT ISHORT VNOISE Conditions VIN=2.8V 1mA≦IOUT≦30mA VIN*VOUT=1A, VOUT=1.76V VIN=2.8V 1mA≦IOUT≦300mA 2.8V≦VIN≦6V IOUT=30mA IOUT=10mA IOUT=100mA IOUT=300mA VIN=2.8V, IOUT=0mA VIN=2.8V, VCE in OFF mode Ripple 0.5Vp-p f=100Hz VIN=2.8V f=1KHz Min Typ Max Units 1.764 1.8 1.836 V 6 360 V mA 6 mV 1 10 100 300 60 0.01 70 70 mV 300 12 120 360 90 1.0 mV uA uA dB IOUT=30mA ±100 ppm/℃ VOUT=0V 10Hz≦f≦100kHz CE input voltage “High” CE input voltage “Low” 50 50 160 mA uVrms V V ℃ 25 ℃ 1.5 0.4 ACE515A-2.5 Electrical Characteristics (VIN=3.5V, TA=25℃, CIN=1μF, COUT=1μF Bold typeface applies over -40℃≦TJ≦85℃, unless otherwise specified.) Parameter Symbol Output Voltage VOUT Input Voltage Maximum Output Current VIN IOUT(Max.) Load Regulation VRLOAD Line Regulation VRLINE Dropout Voltage VDROP Quiescent Current IQ Conditions VIN=3.5V 1mA≦IOUT≦30mA VIN*VOUT=1A, VOUT=2.45V VIN=3.5V 1mA≦IOUT≦300mA 3.5V≦VIN≦6V IOUT=30mA IOUT=10mA IOUT=100mA IOUT=300mA VIN=3.5V, IOUT=0mA Min Typ Max Units 2.45 2.5 2.55 V 6 360 V mA 10 mV 1 6.5 65 200 60 mV 300 10 100 300 90 mV uA VER 1.2 4 Technology Standby Current Power Supply Rejection Ratio Output Voltage Temperature Coefficient Short Current Limit RMS Output Noise CE “High” Voltage CE “Low” Voltage Thermal Shutdown Thermal Shutdown Hysteresis ISTD PSRR (ΔVOUT / ΔIOUT)/ ΔT ISHORT VNOISE ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator VIN=3.5V, VCE in OFF mode Ripple 0.5Vp-p f=100Hz VIN=3.5V f=1KHz 0.01 65 65 1.0 uA IOUT=30mA ±100 ppm/℃ VOUT=0V 10Hz≦f≦100kHz CE input voltage “High” CE input voltage “Low” 50 50 160 mA uVrms V V ℃ 25 ℃ dB 1.5 0.4 ACE515A-2.8 Electrical Characteristics (VIN=3.8V, TA=25℃, CIN=1μF, COUT=1μF Bold typeface applies over -40℃≦TJ≦85℃, unless otherwise specified.) Parameter Symbol Output Voltage VOUT Input Voltage Maximum Output Current VIN IOUT(Max.) Load Regulation VRLOAD Line Regulation VRLINE Dropout Voltage VDROP Quiescent Current Standby Current Power Supply Rejection Ratio Output Voltage Temperature Coefficient Short Current Limit RMS Output Noise CE “High” Voltage CE “Low” Voltage Thermal Shutdown Thermal Shutdown Hysteresis IQ ISTD PSRR (ΔVOUT / ΔIOUT)/ ΔT ISHORT VNOISE Conditions VIN=3.8V 1mA≦IOUT≦30mA VIN*VOUT=1A, VOUT=2.74V VIN=3.8V 1mA≦IOUT≦300mA 3.8V≦VIN≦6V IOUT=30mA IOUT=10mA IOUT=100mA IOUT=300mA VIN=3.8V, IOUT=0mA VIN=3.8V, VCE in OFF mode Ripple 0.5Vp-p f=100Hz VIN=3.8V f=1KHz Min Typ Max Units 2.744 2.8 2.856 V 6 360 V mA 11 mV 1 6.5 65 200 60 0.01 65 65 mV 300 10 100 300 90 1.0 mV uA uA dB IOUT=30mA ±100 ppm/℃ VOUT=0V 10Hz≦f≦100kHz CE input voltage “High” CE input voltage “Low” 50 50 160 mA uVrms V V ℃ 25 ℃ 1.5 0.4 VER 1.2 5 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator ACE515A-3.0 Electrical Characteristics (VIN=4.0V, TA=25℃, CIN=1μF, COUT=1μF Bold typeface applies over -40℃≦TJ≦85℃, unless otherwise specified.) Parameter Symbol Output Voltage VOUT Input Voltage Maximum Output Current VIN IOUT(Max.) Load Regulation VRLOAD Line Regulation VRLINE Dropout Voltage VDROP Quiescent Current Standby Current Power Supply Rejection Ratio Output Voltage Temperature Coefficient Short Current Limit RMS Output Noise CE “High” Voltage CE “Low” Voltage Thermal Shutdown Thermal Shutdown Hysteresis IQ ISTD PSRR (ΔVOUT / ΔIOUT)/ ΔT ISHORT VNOISE Conditions VIN=4.0V 1mA≦IOUT≦30mA VIN*VOUT=1A, VOUT=2.94V VIN=4.0V 1mA≦IOUT≦300mA 4.0V≦VIN≦6V IOUT=30mA IOUT=10mA IOUT=100mA IOUT=300mA VIN=4.0V, IOUT=0mA VIN=4.0V, VCE in OFF mode Ripple 0.5Vp-p f=100Hz VIN=4.0V f=1KHz Min Typ Max Units 2.94 3.0 3.06 V 6 360 V mA 12 mV 1 6.5 65 200 60 0.01 65 65 mV 300 10 100 300 90 1.0 mV uA uA dB IOUT=30mA ±100 ppm/℃ VOUT=0V 10Hz≦f≦100kHz CE input voltage “High” CE input voltage “Low” 50 50 160 mA uVrms V V ℃ 25 ℃ 1.5 0.4 ACE515A-3.3 Electrical Characteristics (VIN=4.3V, TA=25℃, CIN=1μF, COUT=1μF Bold typeface applies over -40℃≦TJ≦85℃, unless otherwise specified.) Parameter Symbol Output Voltage VOUT Input Voltage Maximum Output Current VIN IOUT(Max.) Load Regulation VRLOAD Line Regulation VRLINE Dropout Voltage VDROP Quiescent Current Standby Current IQ ISTD Conditions VIN=4.3V 1mA≦IOUT≦30mA VIN*VOUT=1A, VOUT=3.23V VIN=4.3V 1mA≦IOUT≦300mA 4.3V≦VIN≦6V IOUT=30mA IOUT=10mA IOUT=100mA IOUT=300mA VIN=4.3V, IOUT=0mA VIN=4.3V, VCE in OFF mode Min Typ Max Units 3.234 3.3 3.366 V 6 360 V mA 13 mV 1 6.5 65 200 60 0.01 mV 300 10 100 300 90 1.0 mV uA uA VER 1.2 6 Technology Power Supply Rejection Ratio Output Voltage Temperature Coefficient Short Current Limit RMS Output Noise CE “High” Voltage CE “Low” Voltage Thermal Shutdown Thermal Shutdown Hysteresis PSRR (ΔVOUT / ΔIOUT)/ ΔT ISHORT VNOISE ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Ripple 0.5Vp-p VIN=4.3V f=100Hz f=1KHz 65 65 dB IOUT=30mA ±100 ppm/℃ VOUT=0V 10Hz≦f≦100kHz CE input voltage “High” CE input voltage “Low” 50 50 160 mA uVrms V V ℃ 25 ℃ 1.5 0.4 ACE515A-4.15 Electrical Characteristics (VIN=5.15V, TA=25℃, CIN=1μF, COUT=1μF Bold typeface applies over -40℃≦TJ≦85℃, unless otherwise specified.) Parameter Symbol Output Voltage VOUT Input Voltage Maximum Output Current VIN IOUT(Max.) Load Regulation VRLOAD Line Regulation VRLINE Dropout Voltage VDROP Quiescent Current IQ Standby Current ISTD Power Supply Rejection Ratio Output Voltage Temperature Coefficient Short Current Limit RMS Output Noise CE “High” Voltage CE “Low” Voltage Thermal Shutdown Thermal Shutdown Hysteresis PSRR (ΔVOUT / ΔIOUT)/ ΔT ISHORT VNOISE Conditions VIN=5.15V 1mA≦IOUT≦30mA VIN*VOUT=1A, VOUT=4.06V Min Typ Max Units 4.067 4.15 4.233 V 6 V 300 VIN=5.15V 1mA≦IOUT≦300mA 5.15V≦VIN≦6V IOUT=30mA IOUT=10mA IOUT=100mA IOUT=300mA VIN=5.15V, IOUT=0mA VIN=5.15V, VCE in OFF mode Ripple 0.5Vp-p f=100Hz VIN=5.15V f=1KHz 360 mA 13 mV 1 6.5 65 200 60 mV 10 100 300 90 0.01 1.0 mV uA uA 65 65 dB IOUT=30mA ±100 ppm/℃ VOUT=0V 10Hz≦f≦100kHz CE input voltage “High” CE input voltage “Low” 50 50 160 mA uVrms V V ℃ 25 ℃ 1.5 0.4 VER 1.2 7 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator ACE515A-4.2 Electrical Characteristics (VIN=5.2V, TA=25℃, CIN=1μF, COUT=1μF Bold typeface applies over -40℃≦TJ≦85℃, unless otherwise specified.) Parameter Symbol Output Voltage VOUT Input Voltage Maximum Output Current VIN IOUT(Max.) Load Regulation VRLOAD Line Regulation VRLINE Dropout Voltage VDROP Quiescent Current Standby Current Power Supply Rejection Ratio Output Voltage Temperature Coefficient Short Current Limit RMS Output Noise CE “High” Voltage CE “Low” Voltage Thermal Shutdown Thermal Shutdown Hysteresis IQ ISTD PSRR (ΔVOUT / ΔIOUT)/ ΔT ISHORT VNOISE Conditions VIN=5.2V 1mA≦IOUT≦30mA VIN*VOUT=1A, VOUT=4.12V VIN=5.2V 1mA≦IOUT≦300mA 5.2V≦VIN≦6V IOUT=30mA IOUT=10mA IOUT=100mA IOUT=300mA VIN=5.2V, IOUT=0mA VIN=5.2V, VCE in OFF mode Ripple 0.5Vp-p f=100Hz VIN=5.2V f=1KHz Min Typ Max Units 4.116 4.2 4.284 V 6 360 V mA 13 mV 1 6.5 65 200 60 0.01 65 65 mV 300 10 100 300 90 1.0 mV uA uA dB IOUT=30mA ±100 ppm/℃ VOUT=0V 10Hz≦f≦100kHz CE input voltage “High” CE input voltage “Low” 50 50 160 mA uVrms V V ℃ 25 ℃ 1.5 0.4 VER 1.2 8 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Typical Performance Characteristics ACE515A-1.8 VIN=2.8V TC=25℃ Output Voltage vs. Output Current ACE515A-1.8 VIN=2.8V Dropout Voltage vs. Output Current ACE515A-3.3 VIN=4.3V TC=25℃ Output Voltage vs. Output Current ACE515A-3.3 VIN=4.3V Dropout Voltage vs. Output Current VER 1.2 9 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator ACE515A-1.8 VIN=2.8V Dropout Voltage vs. Case Temperature ACE515A-3.3 VIN=4.3V Dropout Voltage vs. Case Temperature ACE515A-3.3 TC=25℃ ACE515A-1.8 TC=25℃ Current Limit Current Limit VER 1.2 10 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator ACE515A-3.3 VIN=4.3V ACE515A-1.8 VIN=2.8V Current Limit Current Limit ACE515A-1.8 TC=25℃ Output Voltage vs. Input Voltage ACE515A-3.3 TC=25℃ Output Voltage vs. Input Voltage VER 1.2 11 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator ACE515A-1.8 TC=25℃ No Load Output Voltage vs. Input Voltage ACE515A-1.8 VIN=2.8V Output Voltage vs. Case Temperature ACE515A-3.3 TC=25℃ No Load Output Voltage vs. Input Voltage ACE515A-3.3 VIN=4.3V Output Voltage vs. Case Temperature VER 1.2 12 Technology ACE515A-1.8 No Load ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator ACE515A-3.3 No Load Supply Current vs. Input Voltage ACE515A-1.8 VIN=2.8V No Load Supply Current vs. Case Temperature Supply Current vs. Input Voltage ACE515A-1.8 VIN=4.3V No Load Supply Current vs. Case Temperature VER 1.2 13 Technology ACE515A-1.8 VIN=2.8V Supply Current vs. Output Current ACE515A-1.8 TC=25℃ Supply Current vs. Output Current ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator ACE515A-3.3 VIN=4.3V Supply Current vs. Output Current ACE515A-3.3 TC=25℃ Supply Current vs. Output Current VER 1.2 14 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator ACE515A-1.8 Line Transient ACE515A-3.3 Line Transient Conditions: IOUT=30mA, COUT=1μF, VIN=2.8 to 3.8V Conditions: IOUT=30mA, COUT=1μF, VIN=4 to 5V ACE515A-1.8 Load Transient Conditions: IOUT=10mA to 100mA, CIN=1μF, COUT=1μF, VIN=2.8V ACE515A-3.3 Line Transient Conditions: IOUT=10mA to 100mA, CIN=1μF, COUT=1μF, VIN=4.3V VER 1.2 15 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator ACE515A-1.8 CIN=1μF COUT=1μF ACE515A-2.8 Enable Input Response and Auto-discharge ESR vs. Output Current Conditions: VCE=0 to 3V, CIN=1μF, COUT=1μF, VIN=3V, no load ACE515A-1.8 VIN=2.8V IOUT=30mA PSRR ACE515A-3.3 VIN=4.3V IOUT=30mA PSRR VER 1.2 16 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator ACE515A-1.8 Package: SC-70-5 No Heatsink Power Dissipation vs. Ambient Temperature ACE515A-3.3 Package: SC-70-5 No Heatsink Power Dissipation vs. Ambient Temperature Typical Application ACE515A-1.8 ACE515A-3.0 VER 1.2 17 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Packing Information SC-70-5 VER 1.2 18 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Packing Information SOT-23-5 VER 1.2 19 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Packing Information SOT-23-3 VER 1.2 20 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Packing Information SC-82 VER 1.2 21 Technology ACE515A 300mA High Speed, Extremely Low Noise CMOS LDO Regulator Notes ACE does not assume any responsibility for use as critical components in life support devices or systems without the express written approval of the president and general counsel of ACE Electronics Co., LTD. As sued herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and shoes failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ACE Technology Co., LTD. http://www.ace-ele.com/ VER 1.2 22