MITSUBISHI IGBT MODULES CM100DU-24H HIGH POWER SWITCHING USE INSULATED TYPE CM100DU-24H ● IC ................................................................... 100A ● VCES ....................................................... 1200V ● Insulated Type ● 2-elements in a pack APPLICATION UPS, NC machine, AC-Drive control, Servo, Welders OUTLINE DRAWING & CIRCUIT DIAGRAM Dimensions in mm TC measured point 94 80 ±0.25 4 G1E1 12 4 4 11 18 E2 G2 C1 E2 C2E1 2–φ6.5 MOUNTING HOLES 23 23 48 CM 24 17 13 7 13.5 2.5 16 TAB C2E1 E2 21.2 +1 30 –0.5 LABEL #110. t=0.5 C1 G1 E1 25 7.5 16 2.5 E2 G2 3–M5NUTS 12mm deep CIRCUIT DIAGRAM Feb. 2009 1 MITSUBISHI IGBT MODULES CM100DU-24H HIGH POWER SWITCHING USE INSULATED TYPE MAXIMUM RATINGS Symbol VCES VGES IC ICM IE (Note 2) IEM (Note 2) PC (Note 3) Tj Tstg Viso (Tj = 25°C, unless otherwise specified) Item Collector current Emitter current Maximum collector dissipation Junction temperature Storage temperature Isolation voltage — Mounting torque — Weight ELECTRICAL CHARACTERISTICS Symbol Conditions Collector-emitter voltage Gate-emitter voltage Note 1. 2. 3. 4. 5. 6. (Note 1) Ratings Unit 1200 ±20 100 200 100 200 650 –40 ~ +150 –40 ~ +125 2500 2.5 ~ 3.5 3.5 ~ 4.5 310 V V A A A A W °C °C Vrms N·m N·m g (Tj = 25°C, unless otherwise specified) Collector cutoff current Gate-emitter VGE(th) threshold voltage Gate-leakage current IGES Collector-emitter VCE(sat) saturation voltage Input capacitance Cies Output capacitance Coes Reverse transfer capacitance Cres QG Total gate charge td (on) Turn-on delay time tr Turn-on rise time td (off) Turn-off delay time tf Turn-off fall time V EC(Note 2) Emitter-collector voltage t rr (Note 2) Reverse recovery time Q rr (Note 2) Reverse recovery charge Rth(j-c)Q Thermal resistance (Note 5) Rth(j-c)R Contact thermal resistance (Note 1) — — Charged part to base plate, f = 60Hz, AC 1 minute Main terminals M5 screw Mounting M6 screw Typical value VCE = VCES, VGE = 0V Min — Limits Typ — Max 1 IC = 10mA, VCE = 10V 4.5 6 7.5 V — — — — — — — — — — — — — — — — — 2.9 2.85 — — — 375 — — — — — — 0.55 — — 0.5 3.7 — 15 5 3 — 100 200 300 350 3.2 300 — 0.19 0.35 µA nF nF nF nC ns ns ns ns V ns µC K/W K/W — 0.07 — K/W Item ICES Rth(c-f) VGE = 0V VCE = 0V TC = 25°C Pulse TC = 25°C Pulse TC = 25°C Test Conditions ±VGE = VGES, VCE = 0V IC = 100A, VGE = 15V (Note 4) Tj = 25°C Tj = 125°C VCE = 10V VGE = 0V VCC = 600V, IC = 100A, VGE = 15V VCC = 600V, IC = 100A VGE = ±15V RG = 3.1Ω Resistive load IE = 100A, VGE = 0V IE = 100A, die / dt = –200A / µs Junction to case, IGBT part (Per 1/2 module) Junction to case, FWDi part (Per 1/2 module) Case to heat sink, conductive grease applied (Per 1/2 module) (Note 6) Unit mA V Pulse width and repetition rate should be such that the device junction temperature (Tj) does not exceed Tjmax rating. IE, VEC, trr, Qrr & die/dt represent characteristics of the anti-parallel, emitter-collector free-wheel diode. Junction temperature (Tj) should not increase beyond 150°C. Pulse width and repetition rate should be such as to cause negligible temperature rise. Case temperature (TC) measured point is shown in page OUTLINE DRAWING. Typical value is measured by using thermally conductive grease of λ = 0.9[W/(m • K)]. Feb. 2009 2 MITSUBISHI IGBT MODULES CM100DU-24H HIGH POWER SWITCHING USE INSULATED TYPE PERFORMANCE CURVES TRANSFER CHARACTERISTICS (TYPICAL) OUTPUT CHARACTERISTICS (TYPICAL) 200 15 VCE = 10V COLLECTOR CURRENT IC (A) 12 Tj = 25°C 150 11 100 10 9 50 8 0 COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat) (V) VGE = 20 (V) 0 2 4 6 8 100 50 Tj = 25°C Tj = 125°C 0 4 8 12 16 20 COLLECTOR-EMITTER VOLTAGE VCE (V) GATE-EMITTER VOLTAGE VGE (V) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) 5 VGE = 15V Tj = 25°C Tj = 125°C 4 3 2 1 0 0 50 100 150 8 6 IC = 200A 4 IC = 100A IC = 40A 2 0 4 8 12 16 20 GATE-EMITTER VOLTAGE VGE (V) FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) CAPACITANCE CHARACTERISTICS (TYPICAL) 102 Tj = 25°C 3 2 102 7 5 3 2 101 1.0 Tj = 25°C COLLECTOR CURRENT IC (A) CAPACITANCE Cies, Coes, Cres (nF) 7 5 10 0 200 103 EMITTER CURRENT IE (A) 150 0 10 COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat) (V) COLLECTOR CURRENT IC (A) 200 7 5 VGE = 0V 3 2 101 7 5 Cies 3 2 100 Coes 7 5 3 2 Cres 3.5 10–1 –1 10 2 3 5 7 100 2 3 5 7 101 2 3 5 7 102 EMITTER-COLLECTOR VOLTAGE VEC (V) COLLECTOR-EMITTER VOLTAGE VCE (V) 1.5 2.0 2.5 3.0 Feb. 2009 3 MITSUBISHI IGBT MODULES CM100DU-24H HIGH POWER SWITCHING USE INSULATED TYPE tf 3 2 td(off) 102 td(on) 7 5 3 2 tr 101 7 5 VCC = 600V VGE = ±15V RG = 3.1Ω 3 2 100 NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth(j – c) REVERSE RECOVERY TIME trr (ns) Tj = 125°C 7 5 7 101 2 3 5 7 102 2 3 2 5 3 3 2 2 trr 102 101 Irr 7 5 7 5 3 3 2 2 3 5 7 101 2 3 5 7 102 2 COLLECTOR CURRENT IC (A) EMITTER CURRENT IE (A) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT part) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi part) 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7 100 2 3 5 7 101 101 7 Single Pulse 5 3 TC = 25°C Per unit base = Rth(j – c) = 0.19K/W 100 5 101 5 7 NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth(j – c) SWITCHING TIMES (ns) 103 REVERSE RECOVERY CHARACTERISTICS OF FREE-WHEEL DIODE (TYPICAL) 103 102 – di /dt = 200A /µs 7 7 Tj = 25°C 7 5 3 2 3 2 10–1 10–1 10–2 10–2 10–3 10–3 10–5 2 3 5 710–4 2 3 5 7 10–3 7 5 3 2 7 5 3 2 7 5 3 2 7 5 3 2 TIME (s) REVERSE RECOVERY CURRENT Irr (A) HALF-BRIDGE SWITCHING TIME CHARACTERISTICS (TYPICAL) 3 100 10–3 2 3 5 710–2 2 3 5 710–1 2 3 5 7 100 2 3 5 7 101 101 7 Single Pulse 5 3 TC = 25°C 2 100 Per unit base = Rth(j – c) = 0.35K/W 7 5 3 2 3 2 10–1 10–1 10–2 10–2 10–3 10–3 10–5 2 3 5 710–4 2 3 5 7 10–3 7 5 3 2 7 5 3 2 7 5 3 2 7 5 3 2 TIME (s) GATE CHARGE CHARACTERISTICS (TYPICAL) GATE-EMITTER VOLTAGE VGE (V) 20 IC = 100A 15 VCC = 400V VCC = 600V 10 5 0 0 100 200 300 400 500 GATE CHARGE QG (nC) Feb. 2009 4