DS64EV400
www.ti.com
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
DS64EV400 Programmable Quad Equalizer
Check for Samples: DS64EV400
FEATURES
DESCRIPTION
•
•
•
•
The DS64EV400 programmable quad equalizer
provides compensation for transmission medium
losses and reduces the medium-induced deterministic
jitter for four NRZ data channels. The DS64EV400 is
optimized for operation up to 10 Gbps for both cables
and FR4 traces. Each equalizer channel has eight
levels of input equalization that can be programmed
by three control pins, or individually through a Serial
Management Bus (SMBus) interface.
1
2
•
•
•
•
•
•
•
•
•
•
•
Equalizes up to 24 dB Loss at 10 Gbps
Equalizes up to 22 dB Loss at 6.4 Gbps
8 Levels of Programmable Equalization
Settable through Control Pins or SMBus
Tnterface
Operates up to 10 Gbps with 30” FR4 Traces
Operates up to 6.4 Gbps with 40” FR4 Traces
0.175 UI Residual Deterministic Jitter at 6.4
Gbps with 40” FR4 Traces
Single 2.5V or 3.3V Power Supply
Signal Detect for Individual Channels
Standby Mode for Individual Channels
Supports AC or DC-Coupling with Wide Input
Common-Mode
Low Power Consumption: 375 mW Typ at 2.5V
Small 7 mm x 7 mm 48-Pin WQFN Package
9 kV HBM ESD Rating
-40 to 85°C Operating Temperature Range
The equalizer supports both AC and DC-coupled data
paths for long run length data patterns such as
PRBS-31, and balanced codes such as 8b/10b. The
device uses differential current-mode logic (CML)
inputs and outputs. The DS64EV400 is available in a
7 mm x 7 mm 48-pin leadless WQFN package.
Power is supplied from either a 2.5V or 3.3V supply.
Simplified Application Diagram
4
Tx
ASIC/FPGA
High Speed I/O
Rx
OUT
4
IN
DS64EV400
Switch Fabric Card
Backplane/Cable
Sub-system
Line Card
4
Tx
ASIC/FPGA
High Speed I/O
Rx
OUT
IN
4
DS64EV400
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2013, Texas Instruments Incorporated
DS64EV400
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
www.ti.com
Pin Descriptions
Pin Name
I/O, Type (1)
Pin No.
Description
HIGH SPEED DIFFERENTIAL I/O
IN_0+
IN_0–
1
2
I, CML
Inverting and non-inverting CML differential inputs to the equalizer. An on-chip 100Ω
terminating resistor is connected between IN_0+ and IN_0-. Refer to Figure 7.
IN_1+
IN_1–
4
5
I, CML
Inverting and non-inverting CML differential inputs to the equalizer. An on-chip 100Ω
terminating resistor is connected between IN_1+ and IN_1-. Refer to Figure 7.
IN_2+
IN_2–
8
9
I, CML
Inverting and non-inverting CML differential inputs to the equalizer. An on-chip 100Ω
terminating resistor is connected between IN_2+ and IN_2-. Refer to Figure 7.
IN_3+
IN_3–
11
12
I, CML
Inverting and non-inverting CML differential inputs to the equalizer. An on-chip 100Ω
terminating resistor is connected between IN_3+ and IN_3-. Refer to Figure 7.
OUT_0+
OUT_0–
36
35
O, CML
Inverting and non-inverting CML differential outputs from the equalizer. An on-chip 50Ω
terminating resistor connects OUT_0+ to VDD and OUT_0- to VDD.
OUT_1+
OUT_1–
33
32
O, CML
Inverting and non-inverting CML differential outputs from the equalizer. An on-chip 50Ω
terminating resistor connects OUT_1+ to VDD and OUT_1- to VDD.
OUT_2+
OUT_2–
29
28
O, CML
Inverting and non-inverting CML differential outputs from the equalizer. An on-chip 50Ω
terminating resistor connects OUT_2+ to VDD and OUT_2- to VDD.
OUT_3+
OUT_3–
26
25
O, CML
Inverting and non-inverting CML differential outputs from the equalizer. An on-chip 50Ω
terminating resistor connects OUT_3+ to VDD and OUT_3- to VDD.
I, LVCMOS
BST_2, BST_1, and BST_0 select the equalizer strength for all EQ channels. BST_2 is
internally pulled high. BST_1 and BST_0 are internally pulled low.
EQUALIZATION CONTROL
BST_2
BST_1
BST_0
37
14
23
DEVICE CONTROL
EN0
44
I, LVCMOS
Enable Equalizer Channel 0 input. When held High, normal operation is selected. When held
Low, standby mode is selected. EN is internally pulled High.
EN1
42
I, LVCMOS
Enable Equalizer Channel 1 input. When held High, normal operation is selected. When held
Low, standby mode is selected. EN is internally pulled High.
EN2
40
I, LVCMOS
Enable Equalizer Channel 2 input. When held High, normal operation is selected. When held
Low, standby mode is selected. EN is internally pulled High.
EN3
38
I, LVCMOS
Enable Equalizer Channel 3 input. When held High, normal operation is selected. When held
Low, standby mode is selected. EN is internally pulled High.
FEB
21
I, LVCMOS
Force External Boost. When held high, the equalizer boost setting is controlled by BST_[2:0]
pins. When held low, the equalizer boost setting is controlled by SMBus (Table 1) register bits.
FEB is internally pulled High.
SD0
45
O, LVCMOS
Equalizer Ch0 Signal Detect Output. Produces a High when signal is detected.
SD1
43
O, LVCMOS
Equalizer Ch1 Signal Detect Output. Produces a High when signal is detected.
SD2
41
O, LVCMOS
Equalizer Ch2 Signal Detect Output. Produces a High when signal is detected.
SD3
39
O, LVCMOS
Equalizer Ch3 Signal Detect Output. Produces a High when signal is detected.
VDD
3, 6, 7,
10, 13,
15, 46
Power
VDD = 2.5V ± 5% or 3.3V ± 10%. VDD pins should be tied to VDD plane through low inductance
path. A 0.01μF bypass capacitor should be connected between each VDD pin to GND planes.
GND
22, 24,
27, 30,
31, 34
Power
Ground reference. GND should be tied to a solid ground plane through a low impedance path.
DAP
PAD
Power
Ground reference. The exposed pad at the center of the package must be connected to ground
plane of the board.
POWER
SERIAL MANAGEMENT BUS (SMBus) INTERFACE CONTROL PINS
SDA
SDC
CS
18
17
16
I/O, LVCMOS
I, LVCMOS
I, LVCMOS
Data input/output (bi-directional). Internally pulled high.
Clock input. Internally pulled high.
Chip select. When pulled high, access to the equalizer SMBus registers are enabled. When
pulled low, access to the equalizer SMBus registers are disabled. Please refer to “ SMBus
configuration Registers” section for detail information.
Other
Reserv
(1)
2
19, 20
47,48
Reserved. Do not connect.
Note: I = Input O = Output
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
DS64EV400
www.ti.com
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
VDD
SD0
EN0
SD1
EN1
SD2
EN2
SD3
EN3
BST_2
45
44
43
42
41
40
39
38
37
Reserv
47
46
Reserv
48
Connection Diagram
OUT_0+
IN_0+
1
36
IN_0-
2
35
OUT_0-
VDD
3
34
GND
IN_1+
4
33
OUT_1+
IN_1-
5
32
OUT_1-
VDD
6
31
GND
VDD
7
30
GND
IN_2+
8
29
OUT_2+
DS64EV400
TOP VIEW
DAP = GND
18
19
20
21
22
23
24
SDA
Reserv
Reserv
FEB
GND
BST_0
GND
17
OUT_3-
SDC
OUT_3+
25
16
26
12
CS
11
15
IN_3+
IN_3-
VDD
GND
14
OUT_2-
27
13
28
10
BST_1
9
VDD
VDD
IN_2-
Figure 1. WQFN Package
See Package Number NJU0048D
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings
(1) (2)
−0.5V to +4.0V
Supply Voltage (VDD)
CMOS Input Voltage
−0.5V + 4.0V
CMOS Output Voltage
−0.5V to 4.0V
CML Input/Output Voltage
−0.5V to 4.0V
Junction Temperature
+150°C
Storage Temperature
−65°C to +150°C
Lead Temperature (Soldering, 4 Seconds)
+260°C
ESD Rating
HBM, 1.5 kΩ, 100 pF
> 9 kV
EIAJ, 0Ω, 200 pF
> 250V
Thermal Resistance
θJA, No Airflow
30°C/W
(1)
(2)
“Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or
other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating
Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. Absolute
Maximum Numbers are ensured for a junction temperature range of -40°C to +125°C. Models are validated to Maximum Operating
Voltages only.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
3
DS64EV400
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
www.ti.com
Recommended Operating Conditions
Supply Voltage
Min
Typ
Max
Units
VDD2.5 to GND
2.375
2.5
2.625
V
VDD3.3 to GND
3.0
3.3
3.6
V
−40
25
+85
°C
Ambient Temperature
Electrical Characteristics
Over recommended operating supply and temperature ranges with default register settings unless other specified.
Parameter
Test Conditions
Min
Typ
(1)
Max
Units
700
mW
100
mW
490
mW
POWER
P
Power Supply Consumption
Device Output Enabled
(EN [0–3] = High), VDD3.3 (2)
490
Device Output Disable
(EN [0–3] = Low), VDD3.3
P
Power Supply Consumption
Supply Noise Tolerance (3)
N
Device Output Enabled
(EN [0–3] = High), VDD2.5 (2)
360
Device Output Disable
(EN [0–3] = Low), VDD2.5 (2)
30
50 Hz — 100 Hz
100 Hz — 10 MHz
10 MHz — 1.6 GHz
100
40
10
mVP-P
mVP-P
mVP-P
LVCMOS DC SPECIFICATIONS
VIH
High Level Input Voltage
VIL
Low Level Input Voltage
VOH
High Level Output Voltage
VDD3.3
2.0
VDD3.3
V
VDD2.5
1.6
VDD2.5
V
-0.3
0.8
V
IOH = -3mA, VDD3.3
2.4
IOH = -3mA, VDD2.5
2.0
VOL
Low Level Output Voltage
IOL = 3mA
IIN
Input Leakage Current
VIN = VDD
VIN = GND
IIN-P
Input Leakage Current with Internal
Pull-Down/Up Resistors
V
0.4
V
+15
μA
μA
-15
VIN = VDD, with internal pull-down resistors
VIN = GND, with internal pull-up resistors
+120
μA
μA
-20
SIGNAL DETECT
SDH
Signal Detect ON Threshold Level
Default input signal level to assert SD pin, 6.4
Gbps
70
mVp-p
SDI
Signal Detect OFF Threshold Level
Default input signal level to de-assert SD, 6.4
Gbps
40
mVp-p
CML RECEIVER INPUTS (IN_n+, IN_n-)
VTX
Source Transmit Launch Signal Level AC-Coupled or DC-Coupled Requirement,
(IN diff)
Differential measurement at point A.
Figure 2
VINTRE
Input Threshold Voltage
Differential measurement at
point B. Figure 2
Supply Voltage of Transmitter to EQ
DC-Coupled Requirement
VICMDC
Input Common Mode Voltage
DC-Coupled Requirement, Differential
measurement at point A. Figure 2, (5)
RLI
Differential Input Return Loss
100 MHz – 3.2 GHz, with fixture’s effect deembedded
(2)
(3)
(4)
(5)
4
1600
120
(4)
VDDTX
(1)
400
mVP-P
mVP-P
1.6
VDD
V
VDDTX –
0.8
VDDTX
– 0.2
V
10
dB
Typical values represent most likely parametric norms at VDD = 3.3V or 2.5V, TA = 25°C, and at the Recommended Operation
Conditions at the time of product characterization and are not ensured.
The VDD2.5 is VDD = 2.5V ± 5% and VDD3.3 is VDD = 3.3V ± 10%.
Allowed supply noise (mVP-P sine wave) under typical conditions.
Recommended value. Parameter not tested in production.
Measured with clock-like {11111 00000} pattern.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
DS64EV400
www.ti.com
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
Electrical Characteristics (continued)
Over recommended operating supply and temperature ranges with default register settings unless other specified.
Parameter
Test Conditions
Min
Typ
(1)
Max
Units
Differential across IN+ and IN-, Figure 7
85
100
115
Ω
Output Differential Voltage Level
(OUT diff)
Differential measurement with OUT+ and OUTterminated by 50Ω to GND, AC-Coupled
Figure 3
500
620
725
mVP-P
VOCM
Output Common Mode Voltage
Single-ended measurement DC-Coupled with
50Ω terminations (5)
VDD–
0.2
VDD–
0.1
V
tR, tF
Transition Time
20% to 80% of differential output voltage,
measured within 1” from output pins.
Figure 3, (5)
20
60
ps
42
58
Ω
RIN
Input Resistance
CML OUTPUTS (OUT_n+, OUT_n-)
VOD
RO
Output Resistance
Single ended to VDD
50
RLO
Differential Output Return Loss
100 MHz – 1.6 GHz, with fixture’s effect deembedded. IN+ = static high.
10
dB
tPLHD
Differential Low to High Propagation
Delay
Propagation delay measurement at 50% VO
between input to output, 100 Mbps. Figure 4,
240
ps
240
ps
(5)
tPHLD
Differential High to Low Propagation
Delay
tCCSK
Inter Pair Channel to Channel Skew
Difference in 50% crossing between channels
7
ps
tPPSK
Part to Part Output Skew
Difference in 50% crossing between outputs
20
ps
UIP-P
EQUALIZATION
DJ1
Residual Deterministic Jitter
at 10 Gbps
30” of 6 mil microstrip FR4,
EQ Setting 0x06, PRBS-7 (27-1) pattern. (6)
0.20
DJ2
Residual Deterministic Jitter
at 6.4 Gbps
40” of 6 mil microstrip FR4,
EQ Setting 0x06, PRBS-7 (27-1) pattern. (7) (6)
0.17
0.26
UIP-P
DJ3
Residual Deterministic Jitter
at 5 Gbps
40” of 6 mil microstrip FR4,
EQ Setting 0x07, PRBS-7 (27-1) pattern. (7)
0.12
0.20
UIP-P
DJ4
Residual Deterministic Jitter
at 2.5 Gbps
40” of 6 mil microstrip FR4,
EQ Setting 0x07, PRBS-7 (27-1) pattern. (7) (6)
0.1
0.16
UIP-P
RJ
Random Jitter
See
(6)
(8) (9)
0.5
psrms
35
ns
400
ns
150
ns
5
ns
SIGNAL DETECT and ENABLE TIMING
tZISD
tIZSD
Input OFF to ON detect — SD Output Response time measurement at VIN to SD
High Response Time
output, VIN = 800 mVP-P, 100 Mbps, 40” of 6 mil
microstrip FR4
Input ON to OFF detect — SD Output
Figure 2 and Figure 5, (8)
Low Response Time
tOZOED
EN High to Output ON Response
Time
tZOED
EN Low to Output OFF Response
Time
(6)
(7)
(8)
(9)
Response time measurement at EN input to
VO, VIN = 800 mVP-P, 100 Mbps, 40” of 6 mil
microstrip FR4
Figure 2 and Figure 7, (8)
Deterministic jitter is measured at the differential outputs (point C of Figure 2), minus the deterministic jitter before the test channel (point
A of Figure 2). Random jitter is removed through the use of averaging or similar means.
Specification is ensured by characterization at optimal boost setting and is not tested in production.
Measured with clock-like {11111 00000} pattern.
Random jitter contributed by the equalizer is defined as sqrt (JOUT2 – JIN2). JOUT is the random jitter at equalizer outputs in ps-rms, see
point C of Figure 2; JIN is the random jitter at the input of the equalizer in ps-rms, see point B of Figure 2.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
5
DS64EV400
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
www.ti.com
Electrical Characteristics — Serial Management Bus Interface
Over recommended operating supply and temperature ranges unless other specified.
Parameter
Test Conditions
Min
Typ
Max
Units
0.8
V
VDD
V
SERIAL BUS INTERFACE DC SPECIFICATIONS
VIL
Data, Clock Input Low Voltage
VIH
Data, Clock Input High Voltage
IPULLUP
Current Through Pull-Up Resistor or
Current Source
VDD
Nominal Bus Voltage
ILEAK-Bus
Input Leakage Per Bus Segment
ILEAK-Pin
Input Leakage Per Device Pin
CI
RTERM
2.1
High Power Specification
4
mA
2.375
3.6
V
-200
+200
µA
See
(1)
Capacitance for SDA and SDC
See
(1) (2)
External Termination Resistance pull
to VDD = 2.5V ± 5% OR
3.3V ± 10%
VDD3.3, (1) (2) (3)
2000
Ω
VDD2.5, (1) (2) (3)
1000
Ω
-15
µA
10
pF
SERIAL BUS INTERFACE TIMING SPECIFICATIONS (Figure 8)
FSMB
Bus Operating Frequency
TBUF
Bus Free Time Between Stop and
Start Condition
THD:STA
Hold time after (Repeated) Start
Condition. After this period, the first
clock is generated.
See
(4)
10
100
kHz
4.7
µs
4.0
µs
4.7
µs
At IPULLUP, Max
TSU:STA
Repeated Start Condition Setup Time
TSU:STO
Stop Condition Setup Time
4.0
µs
THD:DAT
Data Hold Time
300
ns
TSU:DAT
Data Setup Time
250
TTIMEOUT
Detect Clock Low Timeout
TLOW
Clock Low Period
THIGH
See
(4)
Clock High Period
See
(4)
TLOW:SEXT
Cumulative Clock Low Extend Time
(Slave Device)
See
(4)
tF
Clock/Data Fall Time
See
tR
Clock/Data Rise Time
tPOR
Time in which a device must be
operational after power-on reset
(1)
(2)
(3)
(4)
6
25
ns
35
4.7
4.0
ms
µs
50
µs
2
ms
(4)
300
ns
See
(4)
1000
ns
See
(4)
500
ms
Recommended value. Parameter not tested in production.
Recommended maximum capacitance load per bus segment is 400pF.
Maximum termination voltage should be identical to the device supply voltage.
Compliant to SMBus 2.0 physical layer specification. See System Management Bus (SMBus) Specification Version 2.0, section 3.1.1
SMBus common AC specifications for details.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
DS64EV400
www.ti.com
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
System Management Bus (SMBus) and Configuration Registers
The System Management Bus interface is compatible to SMBus 2.0 physical layer specification. The use of the
Chip Select signal is required. Holding the CS pin High enables the SMBus port allowing access to the
configuration registers. Holding the CS pin Low disables the device's SMBus allowing communication from the
host to other slave devices on the bus. In the STANDBY state, the System Management Bus remains active.
When communication to other devices on the SMBus is active, the CS signal for the DS32EV400s must be
driven Low.
The address byte for all DS64EV400s is AC'h. Based on the SMBus 2.0 specification, the DS64EV400 has a 7bit slave address of 1010110'b. The LSB is set to 0'b (for a WRITE), thus the 8-bit value is 1010 1100'b or AC'h.
The SDC and SDA pins are 3.3V LVCMOS signaling and include high-Z internal pull up resistors. External low
impedance pull up resistors maybe required depending upon SMBus loading and speed. Note, these pins are not
5V tolerant.
Transfer of Data via the SMBus
During normal operation the data on SDA must be stable during the time when SDC is High.
There are three unique states for the SMBus:
START A High-to-Low transition on SDA while SDC is High indicates a message START condition.
STOP A Low-to-High transition on SDA while SDC is High indicates a message STOP condition.
IDLE If SDC and SDA are both High for a time exceeding tBUF from the last detected STOP condition or if they
are High for a total exceeding the maximum specification for tHIGH then the bus will transfer to the IDLE
state.
SMBus Transactions
The device supports WRITE and READ transactions. See Register Description table for register address, type
(Read/Write, Read Only), default value and function information.
Writing a Register
To
1.
2.
3.
4.
5.
6.
7.
8.
9.
write a register, the following protocol is used (see SMBus 2.0 specification).
The Host (Master) selects the device by driving its SMBus Chip Select (CS) signal High.
The Host drives a START condition, the 7-bit SMBus address, and a “0” indicating a WRITE.
The Device (Slave) drives the ACK bit (“0”).
The Host drives the 8-bit Register Address.
The Device drives an ACK bit (“0”).
The Host drive the 8-bit data byte.
The Device drives an ACK bit (“0”).
The Host drives a STOP condition.
The Host de-selects the device by driving its SMBus CS signal Low.
The WRITE transaction is completed, the bus goes IDLE and communication with other SMBus devices may
now occur.
Reading a Register
To
1.
2.
3.
4.
5.
6.
7.
8.
read a register, the following protocol is used (see SMBus 2.0 specification).
The Host (Master) selects the device by driving its SMBus Chip Select (CS) signal High.
The Host drives a START condition, the 7-bit SMBus address, and a “0” indicating a WRITE.
The Device (Slave) drives the ACK bit (“0”).
The Host drives the 8-bit Register Address.
The Device drives an ACK bit (“0”).
The Host drives a START condition.
The Host drives the 7-bit SMBus Address, and a “1” indicating a READ.
The Device drives an ACK bit “0”.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
7
DS64EV400
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
www.ti.com
9. The Device drives the 8-bit data value (register contents).
10. The Host drives a NACK bit “1”indicating end of the READ transfer.
11. The Host drives a STOP condition.
12. The Host de-selects the device by driving its SMBus CS signal Low.
The READ transaction is completed, the bus goes IDLE and communication with other SMBus devices may now
occur.
See Table 1 for more information.
Table 1. SMBus Register Address
Name
Type
Address
Default
Status
0x00
0x00
RO
ID Revision
SD3
SD2
Status
0x01
0x00
RO
EN1
Boost 1
EN0
Boost 0
Status
0x02
0x00
RO
EN3
Boost 3
EN2
Boost 2
Enable/Boost
(CH 0, 1)
0x03
0x44
RW
EN1 Output
0:Enable
1:Disable
Boost Control for CH1
000 (Min Boost)
001
010
011
100 (Default)
101
110
111 (Max Boost)
EN0
Output
0:Enable
1:Disable
Boost Control for CH0
000 (Min Boost)
001
010
011
100 (Default)
101
110
111 (Max Boost)
Enable/Boost
(CH 2, 3)
0x04
0x44
RW
EN3 Output
0:Enable
1:Disable
Boost Control for CH3
000 (Min Boost)
001
010
011
100 (Default)
101
110
111 (Max Boost)
EN2
Output
0:Enable
1:Disable
Boost Control for CH2
000 (Min Boost)
001
010
011
100 (Default)
101
110
111 (Max Boost)
Signal Detect
0x05
0x00
RW
SD3 ON Threshold
Select
00: 70 mV (Default)
01: 55 mV
10: 90 mV
11: 75 mV
SD2 ON Threshold
Select
00: 70 mV (Default)
01: 55 mV
10: 90 mV
11: 75 mV
SD1 ON Threshold
Select
00: 70 mV (Default)
01: 55 mV
10: 90 mV
11: 75 mV
SD0 ON Threshold
Select
00: 70 mV (Default)
01: 55 mV
10: 90 mV
11: 75 mV
Signal Detect
0x06
0x00
RW
SD3 OFF Threshold
Select
00: 40 mV (Default)
01: 30 mV
10: 55 mV
11: 45 mV
SD2 OFF Threshold
Select
00: 40 mV (Default)
01: 30 mV
10: 55 mV
11: 45 mV
SD1 OFF Threshold
Select
00: 40 mV (Default)
01: 30 mV
10: 55 mV
11: 45 mV
SD0 OFF Threshold
Select
00: 40 mV (Default)
01: 30 mV
10: 55 mV
11: 45 mV
SMBus
Control
0x07
0x00
RW
Reserved
Output Level
0x08
0x78
RW
Reserved
(1)
8
Bit 7
(1)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
SD1
Bit 0
SD0
SMBus
Enable
Control
0: Disable
1: Enable
Output Level:
00: 400 mVP-P
01: 540 mVP-P
10: 620 mVPP(Default)
11: 760 mVP-P
Reserved
Note: RO = Read Only, RW = Read/Write
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
DS64EV400
www.ti.com
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
B
A
C
6 mils Trace Width,
FR4 Microstrip Test Channel
DS64EV400
Signal Source
INPUT
SMA
Connector
OUTPUT
SMA
Connector
Figure 2. Test Setup Diagram
80%
80%
0V
OUT diff = (OUT+) ± (OUT-)
20%
20%
tR
tF
Figure 3. CML Output Transition Times
IN diff
0V
tPLHD
OUT diff
tPHLD
0V
Figure 4. Propagation Delay Timing Diagram
IN diff
0V
tIZSD
tZISD
VDD
SD
1.5V
1.5V
0V
Figure 5. Signal Detect (SD) Delay Timing Diagram
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
9
DS64EV400
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
www.ti.com
VDD
EN
1.5V
1.5V
0V
tOZED
tZOED
0V
OUT diff
Figure 6. Enable (EN) Delay Timing Diagram
VDD
10k
IN +
50
VDD
6k
EQ
10k
50
IN 6k
Figure 7. Simplified Receiver Input Termination Circuit
tSU:CS
CS
tLOW
tR
tHIGH
SDC
tHD:STA
tBUF
tHD:DAT
tF
tSU:STA
tSU:DAT
tSU:STO
SDA
SP
ST
SP
ST
Figure 8. SMBus Timing Parameters
DS64EV400 FUNCTIONAL DESCRIPTIONS
The DS64EV400 is a programmable quad equalizer optimized for operation up to 10 Gbps for backplane and
cable applications.
DATA CHANNELS
The DS64EV400 provides four data channels. Each data channel consists of an equalizer stage, a limiting
amplifier, a DC offset correction block, and a CML driver as shown in Figure 9.
10
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
DS64EV400
www.ti.com
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
DC Offset Correction
Data Channel (0-3)
Input
Termination
IN_n +
IN_n SDn
Limiting
Amplifier
Equalizer
BST
CNTL
EN
EN
EN
OUT_n +
OUT_n -
VDD
SD
BST_0:BST_2
ENn
VDD
3
Reg 03,04
bit 7, 3
3
3
Reg 07 SMBus
bit 0 Register
Boost Setting
SMBus Register
FEB
Figure 9. Simplified Block Diagram
EQUALIZER BOOST CONTROL
Each data channel support eight programmable levels of equalization boost. The state of the FEB pin determines
how the boost settings are controlled. If the FEB pin is held High, then the equalizer boost setting is controlled by
the Boost Set pins (BST_[2:0]) in accordance with Table 2. If this programming method is chosen, then the boost
setting selected on the Boost Set pins is applied to all channels. When the FEB pin is held Low, the equalizer
boost level is controlled through the SMBus. This programming method is accessed via the appropriate SMBus
registers (see Table 1). Using this approach, equalizer boost settings can be programmed for each channel
individually. FEB is internally pulled High (default setting); therefore if left unconnected, the boost settings are
controlled by the Boost Set pins (BST_[0:2]). The eight levels of boost settings enables the DS64EV400 to
address a wide range of media loss and data rates.
Table 2. EQ Boost Control Table
6 mil Microstrip FR4
Trace Length (m)
24 AWG Twin-AX cable
length (m)
Channel Loss at 3.2 GHz
(dB)
Channel Loss at 5 GHz
(dB)
BST_N
[2, 1, 0]
0
0
0
0
000
5
2
5
6
001
10
3
7.5
10
010
15
4
10
14
011
20
5
12.5
18
1 0 0 (Default)
25
6
15
21
101
30
7
17
24
110
40
10
22
30
111
DEVICE STATE AND ENABLE CONTROL
The DS64EV400 has an enable feature on each data channel which provides the ability to control device power
consumption. This feature can be controlled either an Enable Pin (EN_n) with Reg 07 = 00'h (default value), or
by the Enable Control Bit register which can be configured through the SMBus port (see Table 1 and Table 3 for
detail register information), which require setting Reg 07 = 01'h and changing register value of Reg 03, 04. If the
Enable is activated using either the external EN_n pin or SMBUS register, the corresponding data channel is
placed in the ACTIVE state and all device blocks function as described. The DS64EV400 can also be placed in
STANDBY mode to save power. In the STANDBY mode only the control interface including the SMBus port, as
well as the signal detection circuit remain active.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
11
DS64EV400
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
www.ti.com
Table 3. Controlling Device State
Register 07[0] (SMBus)
ENn Pin (CMOS)
CH 0:
Reg. 03 bit 3
CH 1:
Reg. 03 bit 7
CH 2:
Reg. 04 bit 3
CH 3:
Reg. 04 bit 7
(EN Control)
0 : Disable
1
X
ACTIVE
0 : Disable
0
X
STANDBY
1 : Enable
X
0
ACTIVE
1 : Enable
X
1
STANDBY
Device State
SIGNAL DETECT
The DS64EV400 features a signal detect circuit on each data channel. The status of the signal of each channel
can be determined by either reading the Signal Detect bit (SDn) in the SMBus registers (see Table 1) or by the
state of each SDn pin. An output logic high indicates the presence of a signal that has exceeded the ON
threshold value (called SD_ON). An output logic Low means that the input signal has fallen below the OFF
threshold value (called SD_OFF). These values are programmed via the SMBus (Table 1). If not programmed via
the SMBus, the thresholds take on the default values as shown in Table 4. The Signal Detect threshold values
can be changed through the SMBus. All threshold values specified are DC peak-to-peak differential signals
(positive signal minus negative signal) at the input of the device.
Table 4. Signal Detect Threshold Values
Channel 0: Bit 1
Channel 1: Bit 3
Channel 2: Bit 5
Channel 3: Bit 7
Channel 0: Bit 0
Channel 1: Bit 2
Channel 2: Bit 4
Channel 3: Bit 6
SD_OFF Threshold
Register 06 (mV)
SD_ON Threshold
Register 05 (mV)
0
0
40 (Default)
70 (Default)
0
1
30
55
1
0
55
90
1
1
45
75
OUTPUT LEVEL CONTROL
The output amplitude of the CML drivers for each channel can be controlled via the SMBus (see Table 1). The
default output level is 620 mVp-p. The following Table presents the output level values supported:
Table 5. Output Level Control Settings
All Channels : Bit 3
All Channels : Bit 2
Output Level Register 08 (mVP-P)
0
0
400
0
1
540
1
0
620 (Default)
1
1
760
AUTOMATIC ENABLE FEATURE
It may be desirable to place unused channels in power-saving Standby mode. This can be accomplished by
connecting the Signal detect (SDn) pin to the Enable (ENn) pin for each channel (See Figure 10). In order for this
option to function properly, the register value for Reg. 07 should be 00'h (default value). If an input signal swing
applied to a data channel is above the voltage level threshold as shown in Table 4, then the SDn output pin is
asserted High. If the SDn pin is connected to the ENn pin, this will enable the equalizer, limiting amplifier, and
output buffer on the data channels; thus the DS64EV400 will automatically enter the ACTIVE state. If the input
signal swing falls below the SD_OFF threshold level, then the SDn output will be asserted Low, causing the
channel to be placed in the STANDBY state.
12
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
DS64EV400
www.ti.com
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
DS64EV400 Applications Information
IN_n r
Limiting
Amplifier
Equalizer
CML
Driver
OUT_n r
ENn
Reg 07 = K¶00
(Default)
Signal Detect
SDn
Figure 10. Automatic Enable Configuration
UNUSED EQUALIZER CHANNELS
It is recommended to put all unused channels into standby mode.
GENERAL RECOMMENDATIONS
The DS64EV400 is a high performance circuit capable of delivering excellent performance. Careful attention
must be paid to the details associated with high-speed design as well as providing a clean power supply. Refer
to the LVDS Owner's Manual for more detailed information on high speed design tips to address signal integrity
design issues.
PCB LAYOUT CONSIDERATIONS FOR DIFFERENTIAL PAIRS
The CML inputs and outputs must have a controlled differential impedance of 100Ω. It is preferable to route CML
lines exclusively on one layer of the board, particularly for the input traces. The use of vias should be avoided if
possible. If vias must be used, they should be used sparingly and must be placed symmetrically for each side of
a given differential pair. Route the CML signals away from other signals and noise sources on the printed circuit
board. See AN-1187(SNOA401) for additional information on WQFN packages.
POWER SUPPLY BYPASSING
Two approaches are recommended to ensure that the DS64EV400 is provided with an adequate power supply.
First, the supply (VDD) and ground (GND) pins should be connected to power planes routed on adjacent layers of
the printed circuit board. The layer thickness of the dielectric should be minimized so that the VDD and GND
planes create a low inductance supply with distributed capacitance. Second, careful attention to supply
bypassing through the proper use of bypass capacitors is required. A 0.01μF bypass capacitor should be
connected to each VDD pin such that the capacitor is placed as close as possible to the DS64EV400. Smaller
body size capacitors can help facilitate proper component placement. Additionally, three capacitors with
capacitance in the range of 2.2 μF to 10 μF should be incorporated in the power supply bypassing design as
well. These capacitors can be either tantalum or an ultra-low ESR ceramic and should be placed as close as
possible to the DS64EV400.
DC COUPLING
The DS64EV400 supports both AC coupling with external ac coupling capacitor, and DC coupling to its upstream
driver, or downstream receiver. With DC coupling, users must ensure the input signal common mode is within the
range of the electrical specification VICMDC and the device output is terminated with 50 Ω to VDD. When power-up
and power-down the device, both the DS64EV400 and the downstream receiver should be power-up and powerdown together. This is to avoid the internal ESD structures at the output of the DS64EV400 at power-down from
being turned on by the downstream receiver.
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
13
DS64EV400
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
www.ti.com
Typical Performance Eye Diagrams and Curves
14
Figure 11. Equalized Signal
(40 In FR4, 2.5Gbps, PRBS7, 0x07 Setting)
Figure 12. Equalized Signal
(40 In FR4, 5Gbps, PRBS7, 0x07 Setting)
Figure 13. Equalized Signal
(40 In FR4, 6.4 Gbps, PRBS7, 0x06 Setting)
Figure 14. Equalized Signal
(40 In FR4, 6.4 Gbps, PRBS31, 0x06 Setting)
Figure 15. Equalized Signal
(30 In FR4, 10 Gbps, PRBS7, 0x06 Setting)
Figure 16. Equalized Signal
(10m 24 AWG Twin-Ax Cable, 6.4 Gbps, PRBS7, 0x07
Setting)
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
DS64EV400
www.ti.com
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
Typical Performance Eye Diagrams and Curves (continued)
Figure 17. Equalized Signal
(32 In Tyco XAUI Backplane, 6.25 Gbps, PRBS7, 0x06
Setting)
Figure 18. DJ vs. EQ Setting (10 Gbps)
Figure 19. DJ vs EQ Setting (6.4 Gbps)
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
15
DS64EV400
SNLS281H – AUGUST 2007 – REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision G (April 2013) to Revision H
•
16
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 15
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS64EV400
PACKAGE OPTION ADDENDUM
www.ti.com
8-Oct-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
DS64EV400SQ/NOPB
ACTIVE
Package Type Package Pins Package
Drawing
Qty
WQFN
NJU
48
250
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
Op Temp (°C)
Device Marking
(4/5)
-40 to 85
DS64EV400
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
8-Oct-2015
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
DS64EV400SQ/NOPB
Package Package Pins
Type Drawing
WQFN
NJU
48
SPQ
250
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
178.0
16.4
Pack Materials-Page 1
7.3
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
7.3
1.3
12.0
16.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DS64EV400SQ/NOPB
WQFN
NJU
48
250
213.0
191.0
55.0
Pack Materials-Page 2
MECHANICAL DATA
NJU0048D
SQA48D (Rev A)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated