1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Features • Single Mode Single Fiber 2x5 SFF SC Receptacle connector • Gigabit Ethernet Compliant • Single +3.3V Power Supply • Tx 1310nm/Rx 1550 nm [B-13/15-1250C-F(DFB)-SSCx] • Tx 1550nm/Rx 1310 nm [B-15/13-1250C-F(DFB)-SSCx] • LVPECL Differential Inputs and Outputs • LVTTL Signal Detection Output • Class 1 Laser Int. Safety Standard IEC-825 Compliant • EMI Shielding Finger Optional • RoHS compliance available Absolute Maximum Rating Parameter Symbol Min. Max. Unit Vcc 0 3.6 V - 0 Vcc V Iout - 30 mA - - 260 ºC Tstg -40 85 ºC Power Supply Voltage Input Voltage Output Current Soldering Temperature Storage Temperature Note 10 seconds on leads only Recommended Operating Condition Parameter Symbol Min. Typ. Max. Unit Power Supply Voltage Vcc 3.1 3.3 3.5 V Operating Temperature (-SSCx(S)) Topr -5 - 70 ºC Operating Temperature (-SSCxA(S)) Topr -40 - 85 ºC - - 1250 - Mbps Data Rate LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Transmitter Specifications Parameter Optical Symbol Min Typical Max Unit Notes Optical Transmit Power Po -9 - -3 dBm B-1X/1X-1250C-F(DFB)-SSC Optical Transmit Power Po -5 - 0 dBm B-1X/1X-1250C-FDFB-SSC2 Optical Transmit Power Po -3 - +2 dBm B-1X/1X-1250C-FDFB-SSC3 Optical Transmit Power Output center Wavelength Po 0 - +5 dBm B-1X/1X-1250C-FDFB-SSC4 λ 1260 1310 1360 nm B-13/15-1250C-F(DFB)-SSCX Output center Wavelength λ 1480 1550 1580 nm B-15/13-1250C-F(DFB)-SSCX Output Spectrum Width ∆λrms - - 4 nm RMS(σ), B-1X/1X-1250C-F-SSC Output Spectrum Width ∆λ - - 1 nm -20dB width, B-1X/1X-1250C-FDFB-SSCX SMSR 30 - - dB B-1X/1X-1250C-FDFB-SSCX ER 9 - - dB Side Mode Supression Ratio Extinction Ratio Output Eye Compliant with IEEE 802.3z Optical Rise Time tr - - 260 ps 20% to 80% Values Optical Fall Time tf - - 260 ps 20% to 80% Values Optical Isolation 30 - - dB RIN - - -116 dB/Hz TJ - - 270 ns Parameter Electrical Symbol Min Typical Max Unit Supply Current ICC - - 150 mA Transmit Enable Voltage VEN 0 - 0.8 V Transmit Disable Voltage VDIS 2 - VCC V Data Input Current-Low IIL -350 - - µA Data Input Current-High IIH - - 350 µA Differential Input Voltage VIH-VIL 300 - - mV Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V Relative Intensity Noise Total Jitter Measured with 27-1 PRBS Transmitter Specifications LUMINENTOIC.COM Notes Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Receiver Specifications Parameter Optical Sensitivity Maximum Input Power Symbol Min Typical Max Unit - - - -22 dBm Pin -3 - - dBm Notes Measured with 27-1 PRBS,BER= 10-12 Signal Detect-Asserted Pa - - -22 dBm Measured on transition: low to high (Note 1) Signal Detect-Deasserted Pd -38 - - dBm Measured on transition: high to low (Note 1) Signal Detect-Hysteresis - 1 - 4 dB Cross Talk - - - -33 dB Wavelength of Operation - 1480 - 1600 nm B-13/15-1250C-F(DFB)-SSCX Wavelength of Operation - 1260 - 1360 nm B-15/13-1250C-F(DFB)-SSCX Max Unit Note The current excludes the output load current Note 1: The SD level should be deasserted when fiber disconnected Receiver Specifications Parameter Electrical Symbol Min Typical ICC - - 100 mA Data Output Voltage-Low VOL -Vcc -2.0 - -1.58 V Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V Supply Current Signal Detect Output Voltage-Low VSDL 0 - 0.5 V Signal Detect Output Voltage-High VSDH 2.0 - Vcc V LUMINENTOIC.COM These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs LVTTL SD Output 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Connection Diagram PIN Symbol 1 RxGND Notes Directly connect this pin to the receiver ground plane 2 RxVcc +3.3V dc power for the receiver section 3 SD Active high on this indicates a received optical signal(LVTTL) 4 RD- Receiver Data Out Bar(LVPECL) 5 RD+ Receiver Data Out (LVPECL) 6 TxVcc 7 TxGND +3.3V dc power for the transmitter section Directly connect this pin to the tranmitter ground plane 8 Warnings TxDIS 9 TD+ Transmitter Data In (LVPECL) 10 TD- Transmitter Data In Bar (LVPECL) LUMINENTOIC.COM Transmitter disable(LVTTL) 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Recommended Circuit Schematic PHY DEVICE TERMINATE AT TRANSCEIVER INPUTS Vcc(+3.3V) Z=50� TD- LVPECL 100� Z=50� TD+ 130� 1 2 3 TxGND TxVcc RD- RD+ 6 TxDIS 7 Tx Disable SD TD+ RxVcc Rx 8 TD- Tx 9 RxGND 10 4 130� 1�H Vcc(+3.3V) C2 C3 10�F Vcc(+3.3V) 1�H C1 5 LVTTL RD+ Z=50� LVPECL 100� RD- Z=50� 130� Vcc(+3.3V) 130� Z=50� SD LVTTL NOTE:C1=C2=C3=100nF TERMINATE AT DEVICE INPUTS The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Recommended Circuit Board Layout DIMENSION IN MILLIMETER (INCHES) NOTES: 1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER. 2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS. 3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Package Diagram B-1X/1X-1250C-F(DFB)-SSCX(A) Units: mm Warnings Housing Lead PIN 1 PIN 5 Legal Notice Housing Lead Stud Stand-off LUMINENTOIC.COM Stand-off PIN 10 PIN 6 Stand-off 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Package Diagram B-1X/1X-1250C-F(DFB)-SSCX(A)S Units: mm Matel Finger Stand-off PIN 1 PIN 5 Stand-off Housing Lead Stud PIN 6 PIN 10 Stand-off Housing Lead LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 8 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Ordering Information Available Options: B-13/15-1250C-F-SSC(A)(S)(-G5) B-13/15-1250C-FDFB-SSC(S)(-G5) B-13/15-1250C-FDFB-SSC2(S)(-G5) B-13/15-1250C-FDFB-SSC3(S)(-G5) B-13/15-1250C-FDFB-SSC4(S)(-G5) B-15/13-1250C-F-SSC(A)(S)(-G5) B-15/13-1250C-FDFB-SSC(S)(-G5) B-15/13-1250C-FDFB-SSC2(S)(-G5) B-15/13-1250C-FDFB-SSC3(S)(-G5) B-15/13-1250C-FDFB-SSC4(S)(-G5) Part numbering Definition: B - 1X/1X - 1250C - F(DFB) - S SC Tx Power Operating Temperature Shielding Finger RoHS compliance available • Wavelength 13/15: Tx Wavelength=1310nm Rx Wavelength=1550nm 15/13: Tx Wavelength=1550nm Rx Wavelength=1310nm • Communication protocol (1.25 Gbps) • +3.3 V SFF Transceiver F= FP Laser transceiver FDFB = DFB Laser transceiver • Single mode fiber • Connector options • Tx Output Power blank = -9 to -3 dBm 2 = -5 to 0 dBm 3 = -3 to +2 dBm 4 = 0 to +5 dBm • Operating Temperature blank = Commercial temperature (-5 to 70 ºC) A = Industrial temperature (-40 to 85 ºC) • Shielding Finger Option Blank = No shielding finger S = with Shielding finger • RoHS compliance available Blank = RoHS non-compliant product G5 = RoHS 5/6-compliant product (lead exemption) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 9 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle Single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 10 LUMNDS796-Jan2407 Rev. A.3