8-Channel Differential DAS with 18-Bit, Bipolar, Simultaneous Sampling ADC AD7609 Data Sheet FEATURES APPLICATIONS 8 simultaneously sampled inputs True differential inputs True bipolar analog input ranges: ±10 V, ±5 V Single 5 V analog supply and 2.3 V to 5.25 V VDRIVE Fully integrated data acquisition solution Analog input clamp protection Input buffer with 1 MΩ analog input impedance Second-order antialiasing analog filter On-chip accurate reference and reference buffer 18-bit ADC with 200 kSPS on all channels Oversampling capability with digital filter Flexible parallel/serial interface SPI/QSPI™/MICROWIRE™/DSP compatible Performance 7 kV ESD rating on analog input channels 98 dB SNR, −107 dB THD Dynamic range: up to 105 dB typical Low power: 100 mW Standby mode: 25 mW 64-lead LQFP package Power line monitoring and protection systems Multiphase motor control Instrumentation and control systems Multiaxis positioning systems Data acquisition systems (DAS) COMPANION PRODUCTS External References: ADR421, ADR431 Digital Isolators: ADuM1402, ADuM5000, ADuM5402 Power: ADIsimPower, Supervisor Parametric Search Additional companion products on the AD7609 product page Table 1. High Resolution, Bipolar Input, Simultaneous Sampling DAS Solutions SingleEnded Inputs AD7608 AD7606 AD7606-6 AD7606-4 AD7607 Resolution 18 Bits 16 Bits 14 Bits 1 True Differential Inputs AD7609 1 Number of Simultaneous Sampling Channels 8 8 6 4 8 Protected by U.S. Patent Number 8,072,360 B2. FUNCTIONAL BLOCK DIAGRAM AVCC CLAMP V1– CLAMP V2+ CLAMP V2– CLAMP V3+ CLAMP V3– CLAMP V4+ CLAMP V4– CLAMP V5+ CLAMP V5– CLAMP V6+ CLAMP V6– CLAMP V7+ CLAMP V7– CLAMP V8+ CLAMP V8– CLAMP RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB 1MΩ RFB SECONDORDER LPF AVCC REGCAP REGCAP 2.5V LDO 2.5V LDO REFCAPB REFCAPA T/H REFIN/REFOUT SECONDORDER LPF T/H 2.5V REF SECONDORDER LPF T/H REF SELECT AGND OS 2 OS 1 OS 0 SECONDORDER LPF T/H SERIAL 8:1 MUX SECONDORDER LPF T/H 18-BIT SAR DIGITAL FILTER PARALLEL/ SERIAL INTERFACE DOUTA DOUTB RD/SCLK CS PAR/SER SEL VDRIVE SECONDORDER LPF T/H PARALLEL DB[15:0] AD7609 SECONDORDER LPF SECONDORDER LPF T/H CLK OSC CONTROL INPUTS T/H AGND CONVST A CONVST B RESET RANGE BUSY FRSTDATA 09760-001 V1+ 1MΩ Figure 1. Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2011–2014 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD7609* PRODUCT PAGE QUICK LINKS Last Content Update: 02/23/2017 COMPARABLE PARTS DESIGN RESOURCES View a parametric search of comparable parts. • AD7609 Material Declaration • PCN-PDN Information EVALUATION KITS • Quality And Reliability • AD7609 Evaluation Board • Symbols and Footprints DOCUMENTATION DISCUSSIONS Data Sheet View all AD7609 EngineerZone Discussions. • AD7609: 8-Channel Differential DAS with 18-Bit, Bipolar, Simultaneous Sampling ADC Data Sheet SAMPLE AND BUY SOFTWARE AND SYSTEMS REQUIREMENTS Visit the product page to see pricing options. • AD7609 Evaluation Software TECHNICAL SUPPORT TOOLS AND SIMULATIONS Submit a technical question or find your regional support number. • AD7609 Filter Model DOCUMENT FEEDBACK REFERENCE MATERIALS Submit feedback for this data sheet. Technical Articles • MS-2210: Designing Power Supplies for High Speed ADC This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified. AD7609 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Converter Details ....................................................................... 21 Applications ....................................................................................... 1 Analog Input ............................................................................... 21 Companion Products ....................................................................... 1 ADC Transfer Function ............................................................. 22 Functional Block Diagram .............................................................. 1 Internal/External Reference ...................................................... 23 Revision History ............................................................................... 2 Typical Connection Diagram ................................................... 24 General Description ......................................................................... 3 Power-Down Modes .................................................................. 24 Specifications..................................................................................... 4 Conversion Control ................................................................... 25 Timing Specifications .................................................................. 7 Digital Interface .............................................................................. 26 Absolute Maximum Ratings.......................................................... 11 Parallel Interface (PAR/SER SEL = 0) ...................................... 26 Thermal Resistance .................................................................... 11 Serial Interface (PAR/SER SEL = 1) ......................................... 26 ESD Caution ................................................................................ 11 Reading During Conversion ..................................................... 27 Pin Configuration and Function Descriptions ........................... 12 Digital Filter ................................................................................ 28 Typical Performance Characteristics ........................................... 15 Layout Guidelines....................................................................... 32 Terminology .................................................................................... 19 Outline Dimensions ....................................................................... 34 Theory of Operation ...................................................................... 21 Ordering Guide .......................................................................... 34 REVISION HISTORY 5/14—Rev. A to Rev. B Changes to Patent Footnote ............................................................. 1 Changes to Figure 37 .......................................................................22 Changes to Figure 39 and Figure 40 ..............................................23 2/12—Rev. 0 to Rev. A Changes to Analog Input Ranges Section ....................................21 7/11—Revision 0: Initial Version Rev. B | Page 2 of 36 Data Sheet AD7609 GENERAL DESCRIPTION The AD7609 is an 18-bit, 8-channel, true differential, simultaneous sampling analog-to-digital data acquisition system (DAS). The part contains analog input clamp protection, a second-order antialiasing filter, a track-and-hold amplifier, an 18-bit charge redistribution successive approximation analogto-digital converter (ADC), a flexible digital filter, a 2.5 V reference and reference buffer, and high speed serial and parallel interfaces. The AD7609 operates from a single 5 V supply and can accommodate ±10 V and ±5 V true bipolar differential input signals while sampling at throughput rates up to 200 kSPS for all channels. The input clamp protection circuitry can tolerate voltages up to ±16.5 V. The AD7609 has 1 MΩ analog input impedance regardless of sampling frequency. The single supply operation, on-chip filtering, and high input impedance eliminate the need for driver op amps and external bipolar supplies. The AD7609 antialiasing filter has a −3 dB cutoff frequency of 32 kHz and provides 40 dB antialias rejection when sampling at 200 kSPS. The flexible digital filter is pin driven, yields improvements in SNR, and reduces the −3 dB bandwidth. Rev. B | Page 3 of 36 AD7609 Data Sheet SPECIFICATIONS VREF = 2.5 V external/internal, AVCC = 4.75 V to 5.25 V, VDRIVE = 2.3 V to 5.25 V; fSAMPLE = 200 kSPS, TA = TMIN to TMAX, unless otherwise noted. 1 Table 2. Parameter DYNAMIC PERFORMANCE Signal-to-Noise Ratio (SNR) 2, 3 Signal-to-(Noise + Distortion) (SINAD)2 Dynamic Range Total Harmonic Distortion (THD)2, 3 Peak Harmonic or Spurious Noise (SFDR)2 Intermodulation Distortion (IMD)2 Second-Order Terms Third-Order Terms Channel-to-Channel Isolation2 ANALOG INPUT FILTER Full Power Bandwidth tGROUP DELAY DC ACCURACY Resolution Differential Nonlinearity2 Integral Nonlinearity2 Total Unadjusted Error (TUE) Positive Full-Scale Error2, 5 Positive Full-Scale Error Drift Positive Full-Scale Error Matching2 Bipolar Zero Code Error2, 6 Bipolar Zero Code Error Drift Bipolar Zero Code Error Matching2 Negative Full-Scale Error2, 5 Negative Full-Scale Error Drift Negative Full-Scale Error Matching2 Test Conditions/Comments fIN = 1 kHz sine wave unless otherwise noted Oversampling by 16; ±10 V range; fIN = 160 Hz Oversampling by 16; ±5 V range; fIN = 160 Hz No oversampling; ±10 V range No oversampling; ±5 V range No oversampling; ±10 V range No oversampling; ±5 V range No oversampling; ±10 V range No oversampling; ±5 V range No oversampling; ±10 V range No oversampling; ±5 V range Min Typ 98 101 100 91 90.5 91 90 91.5 90.5 −107 −110 −108 90 89.5 89.5 89 Max −97 −96 Unit dB dB dB dB dB dB dB dB dB dB dB fa = 1 kHz, fb = 1.1 kHz fIN on unselected channels up to 160 kHz −110 −106 −95 dB dB dB −3 dB, ±10 V range −3 dB, ±5 V range −0.1 dB, ±10 V range −0.1 dB, ±5 V range ±10 V range ±5 V range 32 23 13 10 7.1 10.2 kHz kHz kHz kHz µs µs No missing codes ±10 V range ±5 V range External reference Internal reference External reference Internal reference ±10 V range ±5 V range ±10 V range ± 5 V range ±10 V range ± 5 V range ±10 V range ±5 V range External reference Internal reference External reference Internal reference ±10 V range ±5 V range Rev. B | Page 4 of 36 18 ±0.75 ±3 ±10 ±90 ±8 ±40 ±2 ±7 12 40 ±3 ±3 10 5 2.7 13 ±8 ±40 ±4 ±8 12 40 −0.99/+2 ±7.5 ±140 80 100 ±24 ±48 30 65 ±140 80 100 Bits LSB 4 LSB LSB LSB LSB LSB ppm/°C ppm/°C LSB LSB LSB LSB µV/°C µV/°C LSB LSB LSB LSB ppm/°C ppm/°C LSB LSB Data Sheet Parameter ANALOG INPUT Differential Input Voltage Ranges Absolute Voltage Input Common-Mode Input Range CMRR Analog Input Current Input Capacitance 7 Input Impedance REFERENCE INPUT/OUTPUT Reference Input Voltage Range DC Leakage Current Input Capacitance7 Reference Output Voltage Reference Temperature Coefficient LOGIC INPUTS Input High Voltage (VINH) Input Low Voltage (VINL) Input Current (IIN) Input Capacitance (CIN)7 LOGIC OUTPUTS Output High Voltage (VOH) Output Low Voltage (VOL) Floating-State Leakage Current Floating-State Output Capacitance7 Output Coding CONVERSION RATE Conversion Time Track-and-Hold Acquisition Time Throughput Rate POWER REQUIREMENTS AVCC VDRIVE ITOTAL Normal Mode (Static) Normal Mode (Operational)8 Standby Mode Shutdown Mode AD7609 Test Conditions/Comments VIN = Vx+ − (Vx−) RANGE = 1; ±10 V RANGE = 0; ±5 V ±10 V range, see the Analog Input Clamp Protection section ±5 V range, see the Analog Input Clamp Protection section Min Typ Max Unit −20 −10 −10 +20 +10 +10 V V V −5 +5 V −4 ±5 −70 5.4 2.5 5 1 +4 V dB µA µA pF MΩ 2.475 2.5 2.525 ±1 V µA pF V 10 V, see Figure 28 5 V, see Figure 28 REF SELECT = 1 REFIN/REFOUT 7.5 2.49/ 2.505 ±10 ppm/°C 0.7 × VDRIVE 0.3 × VDRIVE ±2 V V µA pF 0.2 ±20 V V µA pF 5 ISOURCE = 100 µA ISINK = 100 µA VDRIVE − 0.2 ±1 5 Twos complement All eight channels included 4 1 Per channel, all eight channels included 4.75 2.3 200 µs µs kSPS 5.25 5.25 V V 22 28.5 8 11 mA mA mA µA Digital inputs = 0 V or VDRIVE 16 20 5 2 fSAMPLE = 200 kSPS Rev. B | Page 5 of 36 AD7609 Parameter Power Dissipation Normal Mode (Static) Normal Mode (Operational) 8 Standby Mode Shutdown Mode Data Sheet Test Conditions/Comments fSAMPLE = 200 kSPS Min Typ Max Unit 80 100 25 10 115.5 157 42 60.5 mW mW mW µW Temperature range for B version is −40°C to +85°C. See the Terminology section. This specification applies when reading during a conversion or after a conversion. If reading during a conversion in parallel and serial modes with VDRIVE = 5 V, SNR typically reduces by 1.5 dB and THD by 3 dB. 4 LSB means least significant bit. With ±5 V input range, 1 LSB = 76.29 µV. With ±10 V input range, 1 LSB = 152.58 µV. 5 These specifications include the full temperature range variation and contribution from the internal reference buffer but do not include the error contribution from the external reference. 6 Bipolar zero code error is calculated with respect to the analog input voltage. See the Analog Input Clamp Protection section. 7 Sample tested during initial release to ensure compliance. 8 Operational power/current figure includes contribution when running in oversampling mode. 1 2 3 Rev. B | Page 6 of 36 Data Sheet AD7609 TIMING SPECIFICATIONS AVCC = 4.75 V to 5.25 V, VDRIVE = 2.3 V to 5.25 V, VREF = 2.5 V external reference/ internal reference, TA = TMIN to TMAX, unless otherwise noted. 1 Table 3. Parameter PARALLEL/SERIAL/BYTE MODE tCYCLE Limit at TMIN, TMAX Min Typ Max Unit 5 µs 10.1 11.5 µs µs µs 4.15 9.1 18.8 39 78 158 315 100 µs µs µs µs µs µs µs µs 30 ms 13 ms 5 tCONV 3.45 7.87 16.05 33 66 133 257 tWAKE-UP STANDBY tWAKE-UP SHUTDOWN Internal Reference External Reference tRESET tOS_SETUP tOS_HOLD t1 t2 t3 t4 t5 2 t6 t7 PARALLEL READ OPERATION t8 t9 t10 t11 t12 4 50 20 20 25 ns ns ns ns ns ns ns ms ns ns 0 0 ns ns 19 24 30 37 15 22 ns ns ns ns ns ns 45 25 25 0 0.5 25 Description 1/throughput rate Parallel mode, reading during; or after conversion VDRIVE = 2.7 V to 5.25 V; or serial mode: VDRIVE = 3.3 V to 5.25 V, reading during a conversion using DOUTA and DOUTB lines Parallel mode reading after conversion VDRIVE = 2.3 V Serial mode reading after conversion; VDRIVE = 2.7 V, DOUTA and DOUTB lines Serial mode reading after a conversion; VDRIVE = 2.3 V, DOUTA and DOUTB lines Conversion time Oversampling off Oversampling by 2 Oversampling by 4 Oversampling by 8 Oversampling by 16 Oversampling by 32 Oversampling by 64 STBY rising edge to CONVST x rising edge; power-up time from standby mode STBY rising edge to CONVST x rising edge; power-up time from shutdown mode STBY rising edge to CONVST x rising edge; power-up time from shutdown mode RESET high pulse width BUSY to OS x pin setup time BUSY to OS x pin hold time CONVST x high to BUSY high Minimum CONVST x low pulse Minimum CONVST x high pulse BUSY falling edge to CS falling edge setup time Maximum delay allowed between CONVST A, CONVST B rising edges Maximum time between last CS rising edge and BUSY falling edge Minimum delay between RESET low to CONVST x high CS to RD setup time CS to RD hold time RD low pulse width VDRIVE above 4.75 V VDRIVE above 3.3 V VDRIVE above 2.7 V VDRIVE above 2.3 V RD high pulse width CS high pulse width (see Figure 5); CS and RD linked Rev. B | Page 7 of 36 AD7609 Parameter t13 Data Sheet Limit at TMIN, TMAX Min Typ Max Unit 19 24 30 37 ns ns ns ns 19 24 30 37 22 ns ns ns ns ns ns ns 20 15 12.5 10 MHz MHz MHz MHz 18 23 35 ns ns ns 20 26 32 39 ns ns ns ns ns ns 22 ns 18 23 30 35 18 23 30 35 ns ns ns ns ns ns ns ns ns 19 23 30 35 ns ns ns ns t143 t15 t16 t17 6 6 SERIAL READ OPERATION fSCLK t18 t19 3 t20 t21 t22 t23 0.4 tSCLK 0.4 tSCLK 7 FRSTDATA OPERATION t24 t25 t26 Description Delay from CS until DB[15:0] three-state disabled VDRIVE above 4.75 V VDRIVE above 3.3 V VDRIVE above 2.7 V VDRIVE above 2.3 V Data access time after RD falling edge VDRIVE above 4.75 V VDRIVE above 3.3 V VDRIVE above 2.7 V VDRIVE above 2.3 V Data hold time after RD falling edge CS to DB[15:0] hold time Delay from CS rising edge to DB[15:0] three-state enabled Frequency of serial read clock VDRIVE above 4.75 V VDRIVE above 3.3 V VDRIVE above 2.7 V VDRIVE above 2.3 V Delay from CS until DOUTA/DOUTB three-state disabled/delay from CS until MSB valid VDRIVE above 4.75 V VDRIVE above 3.3 V VDRIVE = 2.3 V to 2.7 V Data access time after SCLK rising edge VDRIVE above 4.75 V VDRIVE above 3.3 V VDRIVE above 2.7 V VDRIVE above 2.3 V SCLK low pulse width SCLK high pulse width SCLK rising edge to DOUTA/DOUTB valid hold time CS rising edge to DOUTA/DOUTB three-state enabled Delay from CS falling edge until FRSTDATA three-state disabled VDRIVE above 4.75 V VDRIVE above 3.3 V VDRIVE above 2.7 V VDRIVE above 2.3 V Delay from CS falling edge until FRSTDATA high, serial mode VDRIVE above 4.75 V VDRIVE above 3.3 V VDRIVE above 2.7 V VDRIVE above 2.3 V Delay from RD falling edge to FRSTDATA high VDRIVE above 4.75 V VDRIVE above 3.3 V VDRIVE above 2.7 V VDRIVE above 2.3 V Rev. B | Page 8 of 36 Data Sheet AD7609 Limit at TMIN, TMAX Min Typ Max Parameter t27 Unit 22 29 ns ns 20 27 29 ns ns ns t28 t29 Description Delay from RD falling edge to FRSTDATA low VDRIVE = 3.3 V to 5.25 V VDRIVE = 2.3 V to 2.7 V Delay from 18th SCLK falling edge to FRSTDATA low VDRIVE = 3.3 V to 5.25 V VDRIVE = 2.3 V to 2.7 V Delay from CS rising edge until FRSTDATA three-state enabled Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (30% to 70% of VDD) and timed from a voltage level of 1.6 V. The delay between the CONVST x signals was measured as the maximum time allowed while ensuring a <40 LSB performance matching between channel sets. 3 A buffer is used on the data output pins for these measurements, which is equivalent to a load of 20 pF on the output pins. 1 2 Timing Diagrams t5 CONVST A/ CONVST B tCYCLE CONVST A/ CONVST B t2 t3 tCONV t1 BUSY t4 CS t7 09760-002 tRESET RESET Figure 2. CONVST x Timing—Reading After a Conversion t5 CONVST A/ CONVST B tCYCLE CONVST A/ CONVST B t2 t3 tCONV t1 BUSY t6 CS t7 09760-003 tRESET RESET Figure 3. CONVST x Timing—Reading During a Conversion CS t8 t16 t13 t14 DATA: DB[15:0] FRSTDATA V1 [17:2] INVALID t24 t26 V1 [1:0] V2 [17:2] t17 t15 V2 [1:0] V8 [17:2] t27 Figure 4. Parallel Mode Separate CS and RD Pulses Rev. B | Page 9 of 36 V8 [1:0] t29 09760-004 RD t9 t11 t10 AD7609 Data Sheet t12 CS, RD t16 t13 V1 [17:2] V1 [1:0] V2 [17:2] V2 [1:0] V7 [17:2] V7 [1:0] V8 [17:2] t17 V8 [1:0] 09760-005 DATA: DB[15:0] FRSTDATA Figure 5. CS and RD Linked Parallel Mode CS t21 SCLK t19 t18 DOUTA, DOUTB t20 DB17 t22 DB14 DB13 t25 DB1 t23 DB0 t29 09760-006 t28 FRSTDATA Figure 6. Serial Read Operation Rev. B | Page 10 of 36 Data Sheet AD7609 ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Table 4. Parameter AVCC to AGND VDRIVE to AGND Analog Input Voltage to AGND 1 Digital Input Voltage to AGND Digital Output Voltage to AGND REFIN to AGND Input Current to Any Pin Except Supplies1 Operating Temperature Range B Version Storage Temperature Range Junction Temperature Pb/SN Temperature, Soldering Reflow (10 sec to 30 sec) Pb-Free Temperature, Soldering Reflow ESD (All Pins Except Analog Inputs) ESD (Analog Input Pins Only) 1 Rating −0.3 V to +7 V −0.3 V to AVCC + 0.3 V ±16.5 V −0.3 V to VDRIVE + 0.3 V −0.3 V to VDRIVE + 0.3 V −0.3 V to AVCC + 0.3 V ±10 mA −40°C to +85°C −65°C to +150°C 150°C 240(+0)°C 260(+0)°C 2 kV 7 kV Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL RESISTANCE θJA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. These specifications apply to a 4-layer board. Table 5. Thermal Resistance Package Type 64-Lead LQFP ESD CAUTION Transient currents of up to 100 mA do not cause SCR latch-up. Rev. B | Page 11 of 36 θJA 45 θJC 11 Unit °C/W AD7609 Data Sheet V1– V1+ V2– V2+ V3– V3+ V4– V4+ V5– 64 63 62 61 60 59 58 V5+ V6– V6+ V7+ V7– V8+ V8– PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 57 56 55 54 53 52 51 50 49 48 AVCC AVCC 1 ANALOG INPUT DECOUPLING CAPACITOR PIN PIN 1 AGND 2 OS 0 3 POWER SUPPLY OS 1 4 GROUND PIN OS 2 5 47 AGND 46 REFGND 45 REFCAPB 44 REFCAPA PAR/SER SEL 6 DATA OUTPUT STBY 7 RANGE 8 DIGITAL OUTPUT DIGITAL INPUT REFERENCE INPUT/OUTPUT 43 REFGND AD7609 42 REFIN/REFOUT TOP VIEW (Not to Scale) 41 AGND CONVST A 9 40 AGND CONVST B 10 39 REGCAP RESET 11 38 AVCC RD/SCLK 12 37 AVCC 36 REGCAP CS 13 BUSY 14 35 AGND FRSTDATA 15 DB0 16 34 REF SELECT 33 DB15 09760-007 DB14 DB13 DB12 DB11 DB9 DB10 AGND DB8/DOUTB VDRIVE DB7/DOUTA DB6 DB5 DB4 DB3 DB2 DB1 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Figure 7. Pin Configuration Table 6. Pin Function Descriptions Pin No. 1, 37, 38, 48 Type 1 P Mnemonic AVCC 2, 26, 35, 40, 41, 47 P AGND 23 P VDRIVE 36, 39 P REGCAP 49, 51, 53, 55, 57, 59, 61, 63 50, 52, 54, 56, 58, 60, 62, 64 42 AI+ V1+ to V8+ AI− V1− to V8− REF REFIN/ REFOUT 34 DI REF SELECT 44, 45 REF 43, 46 REF REFCAPA, REFCAPB REFGND Description Analog Supply Voltage 4.75 V to 5.25 V. This supply voltage is applied to the internal front-end amplifiers and to the ADC core. These supply pins should be decoupled to AGND. Analog Ground. This pin is the ground reference point for all analog circuitry on the AD7609. All analog input signals and external reference signals should be referred to these pins. All six of these AGND pins should connect to the AGND plane of a system. Logic Power Supply Input. The voltage (2.3 V to 5 V) supplied at this pin determines the operating voltage of the interface. This pin is nominally at the same supply as the supply of the host interface (that is, DSP, FPGA). Decoupling Capacitor Pins for Voltage Output from Internal Regulator. These output pins should be decoupled separately to AGND using a 1 μF capacitor. The voltage on these output pins is in the range of 2.5 V to 2.7 V. Analog Input V1+ to Analog Input V8+. These pins are the positive terminal of the true differential analog inputs. The analog input range of these channels is determined by the RANGE pin. Analog Input V1− to Analog Input V8−. These are the negative terminals of the true differential analog inputs. The analog input range of these channels is determined by the RANGE pin. The signal on this pin should be 180° out of phase with the corresponding Vx+ pin. Reference Input/ Reference Output. The on-chip reference of 2.5 V is available on this pin for external use if the REF SELECT pin is set to a logic high. Alternatively, the internal reference can be disabled by setting the REF SELECT pin to a logic low and an external reference of 2.5 V can be applied to this input. See the Internal/External Reference section. Decoupling is required on this pin for both the internal or external reference options. A 10 µF capacitor should be applied from this pin to ground close to the REFGND pins. Internal/External Reference Selection Input. Logic input. If this pin is set to logic high, the internal reference is selected and is enabled. If this pin is set to logic low, the internal reference is disabled and an external reference voltage must be applied to the REFIN/REFOUT pin. Reference Buffer Output Force/Sense Pins. These pins must be connected together and decoupled to AGND using a low ESR 10 μF ceramic capacitor. Reference Ground Pins. These pins should be connected to AGND. Rev. B | Page 12 of 36 Data Sheet AD7609 Pin No. 8 Type 1 DI Mnemonic RANGE 6 DI PAR/ SER SEL 9, 10 DI CONVST A, CONVST B 13 DI CS 12 DI RD/SCLK 14 DO BUSY 11 DI RESET 15 DO FRSTDATA 7 DI STBY Description Analog Input Range Selection. Logic input. The polarity on this pin determines the input range of the analog input channels. If this pin is tied to a logic high, the analog input range is ±10 V for all channels. If this pin is tied to a logic low, the analog input range is ±5 V for all channels. A logic change on this pin has an immediate effect on the analog input range. Changing this pin during a conversion is not recommended. See the Analog Input section for more details. Parallel/Serial Interface Selection Input. Logic input. If this pin is tied to a logic low, the parallel interface is selected. If this pin is tied to a logic high, the serial interface is selected. In serial mode, the RD/SCLK pin functions as the serial clock input. The DB7/DOUTA and DB8/DOUTB pins function as serial data outputs. When the serial interface is selected, the DB[15:9] and DB[6:0] pins should be tied to AGND. Conversion Start Input A, Conversion Start Input B. Logic inputs. These logic inputs are used to initiate conversions on the analog input channels. For simultaneous sampling of all input channels, CONVST A and CONVST B can be shorted together and a single conversion start signal applied. Alternatively, CONVST A can be used to initiate simultaneous sampling for V1, V2, V3, and V4, and CONVST B can be used to initiate simultaneous sampling on the other analog inputs (V5, V6, V7, and V8). This is only possible when oversampling is not switched on. When the CONVST A or CONVST B pin transitions from low to high, the front-end track-and-hold circuitry for their respective analog inputs is set to hold. This function allows a phase delay to be created inherently between the sets of analog inputs. Chip Select. This active low logic input frames the data transfer. When both CS and RD are logic low in parallel mode, the output bus (DB[15:0]) is enabled and the conversion result is output on the parallel data bus lines. In serial mode, the CS is used to frame the serial read transfer and clocks out the MSB of the serial output data. Parallel Data Read Control Input When Parallel Interface is Selected (RD)/Serial Clock Input When Serial Interface is Selected (SCLK). When both CS and RD are logic low in parallel mode, the output bus is enabled. In parallel mode, two RD pulses are required to read the full 18 bits of conversion results from each channel. The first RD pulse outputs DB[17:2], and the second RD pulses outputs DB[1:0]. In serial mode, this pin acts as the serial clock input for data transfers. The CS falling edge takes the data output lines, DOUTA and DOUTB, out of three-state and clocks out the MSB of the conversion result. The rising edge of SCLK clocks all subsequent data bits onto the serial data outputs, DOUTA and DOUTB. For further information, see the Conversion Control section. Busy Output. This pin transitions to a logic high after both CONVST A and CONVST B rising edges and indicates that the conversion process has started. The BUSY output remains high until the conversion process for all channels is complete. The falling edge of BUSY signals that the conversion data is being latched into the output data registers and will be available to be read after a time, t4. Any data read while BUSY is high should be complete before the falling edge of BUSY occurs. Rising edges on CONVST A or CONVST B have no effect while the BUSY signal is high. Reset Input. When set to logic high, the rising edge of RESET resets the AD7609. The part must receive a RESET pulse after power-up. To achieve the specified performance after the RESET signal, the tWAKE_UP SHUTDOWN time should elapse between power-on and the RESET pulse. The RESET high pulse should be typically 100 ns wide. If a RESET pulse is applied during a conversion, the conversion is aborted. If a RESET pulse is applied during a read, the contents of the output registers reset to all zeros. Digital Output. The FRSTDATA output signal indicates when the first channel, V1, is being read back on either the parallel or serial interface. When the CS input is high, the FRSTDATA output pin is in three-state. The falling edge of CS takes FRSTDATA out of three-state. In parallel mode, the falling edge of RD corresponding to the result of V1 then sets the FRSTDATA pin high, indicating that the result from V1 is available on the output data bus. The FRSTDATA output returns to a logic low following the third falling edge of RD. In serial mode, FRSTDATA goes high on the falling edge of CS as this clocks out the MSB of V1 on DOUTA. It returns low on the 18th SCLK falling edge after the CS falling edge. See the Conversion Control section for more details. Standby Mode Input. This pin is used to place the AD7609 into one of two power-down modes: standby mode or shutdown mode. The power-down mode entered depends on the state of the RANGE pin, as shown in Table 8. When in standby mode, all circuitry except the on-chip reference, regulators, and regulator buffers is powered down. When in shutdown mode, all circuitry is powered down. Rev. B | Page 13 of 36 AD7609 Data Sheet Pin No. 5, 4, 3 Type 1 DI Mnemonic OS [2:0] 33 DO/DI DB15 32 DO/DI DB14 31 to 27 DO DB[13:9] 24 DO DB7/DOUTA 25 DO DB8/DOUTB 22 to 16 DO DB[6:0] 1 Description Oversampling Mode Pins. Logic inputs. These inputs are used to select the oversampling ratio. OS 2 is the MSB control bit, and OS 0 is the LSB control bit. See the Digital Filter section for additional details on the oversampling mode of operation and Table 9 for oversampling bit decoding. Parallel Output Data Bits, Data Bit 15. When PAR/SER SEL = 0, this pin acts as three-state parallel digital output pin. This pin is used to output DB17 of the conversion result during the first RD pulse and DB1 of the same conversion result during the second RD pulse. When PAR/SER SEL = 1, this pin should be tied to AGND. Parallel Output Data Bits, Data Bit 14. When PAR/SER SEL = 0, this pin acts as three-state parallel digital output pin. When CS and RD are low, this pin is used to output DB16 of the conversion result during the first RD pulse and DB0 of the same conversion result during the second RD pulse. When PAR/SER SEL = 1, this pin should be tied to AGND. Parallel Output Data Bits, Data Bit 13 to Data Bit 9. When PAR/SER SEL = 0, these pins act as three-state parallel digital input/output pins. When CS and RD are low, these pins are used to output DB15 to DB11 of the conversion result during the first RD pulse and output 0 during the second RD pulse. When PAR/SER SEL = 1, these pins should be tied to AGND. Parallel Output Data Bit 7 (DB7)/Serial Interface Data Output Pin (DOUTA). When PAR/SER SEL = 0, this pins acts as a three-state parallel digital input/output pin. When CS and RD are low, this pin is used to output DB9 of the conversion result. When PAR/SER SEL = 1, this pin functions as DOUTA and outputs serial conversion data. See the Conversion Control section for further details. Parallel Output Data Bit 8 (DB8)/Serial Interface Data Output Pin (DOUTB). When PAR/SER SEL = 0, this pins acts as a three-state parallel digital input/output pin. When CS and RD are low, this pin is used to output DB10 of the conversion result. When PAR/SER SEL = 1, this pin functions as DOUTB and outputs serial conversion data. See the Conversion Control section for further details. Parallel Output Data Bits, Data Bit 6 to Data Bit 0. When PAR/SER SEL = 0, these pins act as three-state parallel digital input/output pins. When CS and RD are low, these pins are used to output DB8 to DB2 of the conversion result during the first RD pulse and output 0 during the second RD pulse. When PAR/SER SEL = 1, these pins should be tied to AGND. Refers to classification of pin type; P denotes power, AI denotes analog input, REF denotes reference, DI denotes digital input, DO denotes digital output. Rev. B | Page 14 of 36 Data Sheet AD7609 TYPICAL PERFORMANCE CHARACTERISTICS 3 0 AVCC, VDRIVE = 5V INTERNAL REFERENCE ±10V RANGE fSAMPLE = 200 kSPS fIN = 1kHz 16384 POINT FFT SNR = 91.52dB THD = –111.05dB –40 1 –80 0 ±10V RANGE AVCC, VDRIVE = 5V TA = 25°C fSAMPLE = 200 kSPS WCP INL = 1.69 LSB WCN INL = –1.3 LSB –1 –100 –2 –120 –140 CODE Figure 8. FFT Plot, ±10 V Range 09760-010 100k 229,376 80k 196,608 60k 131,072 40k INPUT FREQUENCY (Hz) 98,304 20k 65,536 0 32,768 –160 09760-008 0 –3 163,840 SNR (dB) –60 2 INL (LSB) –20 Figure 11. Typical INL, ±10 V Range 1.0 AVCC, VDRIVE = 5V INTERNAL REFERENCE ±5V RANGE fSAMPLE = 200kSPS f IN = 1kHz 16,384 POINT FFT SNR = 91.12dB THD = –109.77dB –40 –60 0.6 0.4 DNL (LSB) –20 AMPLITUDE (dB) ±10V RANGE AVCC, VDRIVE = 5V TA = 25°C fSAMPLE = 200 kSPS WCP DNL = 0.33 LSB WCN DNL = –0.32 LSB 0.8 0 –80 0.2 0 –0.2 –0.4 –100 –0.6 –120 –0.8 –140 CODE Figure 9. FFT Plot, ±5 V Range 09760-011 229,376 196,608 163,840 100k 131,072 80k 60k 40k INPUT FREQUENCY (Hz) 98,304 20k 65,536 0 32,768 –160 09760-009 0 –1.0 Figure 12. Typical DNL, ±10 V Range 3 0 –60 1 INL (LSB) –40 –80 0 –1 ±5V RANGE AVCC, VDRIVE = 5V TA = 25°C fSAMPLE = 200 kSPS WCP INL = 1.56 LSB WCN INL = –1.22 LSB –100 –2 –120 –140 6 Figure 10. FFT Plot, ±10 V Range CODE Figure 13. Typical INL, ±5 V Range Rev. B | Page 15 of 36 09760-012 5 229,376 4 196,608 3 163,840 2 INPUT FREQUENCY (kHz) 131,072 1 98,304 0 65,536 –160 32,768 0 –3 09760-109 AMPLITUDE (dB) 2 AVCC , VDRIVE = 5V INTERNAL REFERENCE ±10V RANGE fSAMPLE = 12.5kSPS fIN = 1Hz 8192 POINT FFT SNR = 100.71dB THD: –111.74 dB –20 AD7609 Data Sheet 1.0 ±5V RANGE AVCC, VDRIVE = 5V TA = 25°C fSAMPLE = 200 kSPS WCP INL = 0.45 LSB WCN INL = –0.38 LSB 32 0.2 0 –0.2 –0.4 –0.6 –0.8 16 NFS ERROR 8 0 –8 –16 –24 –40 –40 09760-013 229,376 196,608 163,840 131,072 98,304 65,536 CODE –25 –10 20 65 80 8 ±10V RANGE 20 ±5V RANGE 0 –20 6 4 AVCC, VDRIVE = 5V 2 fSAMPLE = 200 kSPS –40 TA = 25°C EXTERNAL REFERENCE SOURCE RESISTANCE IS MATCHED ON THE V– INPUT ±10V AND ±5V RANGE 0 200kSPS AVCC, VDRIVE = 5V EXTERNAL REFERENCE –25 –10 5 20 35 50 65 80 TEMPERATURE (°C) –2 09760-117 –60 0 20k 40k 60k 100k 80k 120k SOURCE RESISTANCE (Ω) 09760-219 PFS/NFS ERROR (%FS) 40 Figure 18. PFS and NFS Error vs. Source Resistance Figure 15. NFS Error vs. Temperature 105 80 AVCC, VDRIVE = 5V fSAMPLE CHANGES WITH OS RATE 60 TA = 25°C INTERNAL REFERENCE ±10V RANGE 100 40 SNR (dBs) 20 0 ±5V RANGE –20 95 90 NO OS OS × 2 OS × 4 OS × 8 OS × 16 OS × 32 OS × 64 ±10V RANGE –40 85 200kSPS AVCC, VDRIVE = 5V EXTERNAL REFERENCE –60 –25 –10 5 20 35 50 TEMPERATURE (°C) 65 80 80 09760-118 PFS ERROR (LSB) 50 10 60 –80 –40 35 Figure 17. NFS and PFS Error Matching 80 –80 –40 5 TEMPERATURE (°C) Figure 14. Typical DNL, ±5 V Range NFS ERROR (LSB) ±10V RANGE AVCC, VDRIVE = 5V EXTERNAL REFERENCE –32 32,768 0 –1.0 PFS ERROR 24 10 100 10k 10k INPUT FREQUENCY (Hz) Figure 19. SNR vs. Input Frequency, ±10 V Range Figure 16. PFS Error vs. Temperature Rev. B | Page 16 of 36 100k 09760-017 DNL (LSB) 0.4 40 09760-218 0.6 NFS/PFS CHANNEL MATCHING (LSB) 0.8 Data Sheet AD7609 8 105 AVCC, VDRIVE = 5V fSAMPLE CHANGES WITH OS RATE TA = 25°C INTERNAL REFERENCE ±5V RANGE 95 90 NO OS OS × 2 OS × 4 OS × 8 OS × 16 OS × 32 OS × 64 85 100 2 0 ±5V RANGE –2 ±10V RANGE 200 kSPS AV CC,VDRIVE = 5V EXTERNAL REFERENCE –4 80 10 4 10k 10k 100k INPUT FREQUENCY (Hz) –6 –40 0 –20 40 20 TEMPERATURE (°C) 80 60 09760-023 BIPOLAR ZERO ERROR (LSB) 6 09760-018 SNR (dBs) 100 Figure 23. Bipolar Zero Code Error vs. Temperature Figure 20. SNR vs. Input Frequency, ±5 V Range –70 –90 0Ω 10Ω 500Ω 1.2kΩ 5kΩ 10kΩ –100 –120 1 10 FREQUENCY (kHz) 100 09760-020 –110 12 ±5V RANGE 8 4 ±10V RANGE 0 –4 –8 200kSPS AVCC, VDRIVE = 5V EXTERNAL REFERENCE –12 –16 –40 –25 –10 5 20 35 50 65 80 TEMPERATURE (°C) Figure 24. Bipolar Zero Code Error Matching Between Channels Figure 21. THD vs. Input Frequency for Various Source Impedances, ±10 V Range –50 –40 –50 –60 CHANNEL-TO-CHANNEL ISOLATION (dB) ±5V RANGE AVCC, VDRIVE = 5V TA = 25°C fSAMPLE = 200 kSPS RSOURCE MATCHED ON Vx+, Vx– INPUTS THD (dB) –70 –80 0Ω 10Ω 500Ω 1.2kΩ 5kΩ 10kΩ –90 –100 –120 1 10 FREQUENCY (kHz) 100 09760-019 –110 AV CC, VDRIVE = 5V INTERNAL REFERENCE AD7609 RECOMMENDED DECOUPLING USED fSAMPLE = 200kSPS TA = 25°C –60 –70 –80 ±10V RANGE –90 ±5V RANGE –100 –110 –120 –130 –140 0 20 40 60 80 100 120 NOISE FREQUENCY (kHz) Figure 25. Channel-to-Channel Isolation Figure 22. THD vs. Input Frequency for Various Source Impedances, ±5 V Range Rev. B | Page 17 of 36 140 160 09760-225 THD (dB) –80 16 09760-224 ±10V RANGE AVCC, VDRIVE = 5V TA = 25°C fSAMPLE = 200 kSPS RSOURCE MATCHED ON Vx+, Vx– INPUTS BIPOLAR ZERO CODE ERROR MATCHING (LSB) –60 AD7609 Data Sheet 22 110 20 ±5V RANGE 95 90 85 AVCC = VDRIVE = 5V TA = 25°C INTERNAL REFERENCE fSAMPLE SCALES WITH OS RATIO 80 NO OS OS × 2 OS × 4 OS × 8 OS × 16 OS × 32 OS × 64 OVERSAMPLING RATIO 09760-023 DYNAMIC RANGE (dB) ±10V RANGE 100 18 16 14 12 AVCC, VDRIVE = 5V 10 TA = 25°C INTERNAL REFERENCE fSAMPLE VARIES WITH OS RATE 8 NO OS OS × 2 OS × 4 OS × 8 OS × 16 OS × 32 OS × 64 OVERSAMPLING RATIO Figure 26. Dynamic Range vs. Oversampling Ratio 09760-227 AVCC SUPPLY CURRENT (mA) 105 Figure 29. Supply Current vs. Oversampling Rate 140 AVCC = 5.25V REFOUT VOLTAGE (V) AVCC = 5V 2.5000 2.4995 AVCC = 4.75V 2.4990 2.4985 130 120 ±10V RANGE 110 ±5V RANGE 100 90 80 AVCC, VDRIVE = 5V INTERNAL REFERENCE AD7609 RECOMMENDED DECOUPLING USED fSAMPLE = 200kSPS TA = 25°C 70 60 –25 –10 5 20 35 50 65 80 TEMPERATURE (°C) 0 09760-029 2.4980 –40 100 200 300 400 500 600 700 800 09760-130 2.5005 POWER SUPPLY REJECTION RATIO (dB) 2.5010 900 1000 1100 AVCC NOISE FREQUENCY (kHz) Figure 27. Reference Output Voltage vs. Temperature for Different Supply Voltages Figure 30. PSRR 0 10 AVCC, VDRIVE = 5V fSAMPLE = 200kSPS AVCC, VDRIVE = 5V TA = 25°C fSAMPLE = 200kSPS INTERNAL REFERENCE –10 –20 5 CMRR (dB) 0 –5 –15 –20 –15 –10 –5 0 ±5V RANGE –50 –60 ±10V RANGE –80 –90 5 10 15 DIFFERENTIAL ANALOG INPUT VOLTAGE (Vx+ – (Vx–)) (V) 20 –100 10 100 1k 10k FREQUENCY (Hz) Figure 28. Analog Input Current vs. Input Voltage Over Temperature Rev. B | Page 18 of 36 Figure 31. CMRR vs. Common-Mode Ripple Frequency 100k 09760-028 –10 –40 –70 +25°C V+ +25°C V– +85°C V– +85°C V+ –40°C V– –40°C V+ 09760-025 CURRENT (µA) –30 Data Sheet AD7609 TERMINOLOGY Integral Nonlinearity The maximum deviation from a straight line passing through the endpoints of the ADC transfer function. The endpoints of the transfer function are zero scale, a ½ LSB below the first code transition, and full scale at ½ LSB above the last code transition. Differential Nonlinearity The difference between the measured and the ideal 1 LSB change between any two adjacent codes in the ADC. Bipolar Zero Code Error The deviation of the midscale transition (all 1s to all 0s) from the ideal VIN voltage, that is, AGND. Bipolar Zero Code Error Match The difference in bipolar zero code error between any two input channels. Positive Full-Scale Error The last transition (from 011 . . . 10 to 011 . . . 11 in twos complement coding) should occur for an analog voltage 1½ LSB below the nominal full scale (9.99977 V for the ±10 V range and 4.99988 V for the ±5 V range). The positive full-scale error is the deviation of the actual level of the last transition from the ideal level. Positive Full-Scale Error Match The difference in positive full-scale error between any two input channels. Negative Full-Scale Error The first transition (from 100 . . . 00 to 100 . . . 01 in twos complement coding) should occur for an analog voltage ½ LSB above the negative full scale (−9.999923 V for the ±10 V range and −4.9999618 for the ±5 V range). The negative full-scale error is the deviation of the actual level of the first transition from the ideal level. Negative Full-Scale Error Match The difference in negative full-scale error between any two input channels. Track-and-Hold Acquisition Time The track-and-hold amplifier returns to track mode at the end of the conversion. The track-and-hold acquisition time is the time required for the output of the track-and-hold amplifier to reach its final value, within ±1 LSB, after the end of the conversion. See the Track-and-Hold Amplifiers section for more details. Signal-to-(Noise + Distortion) Ratio The measured ratio of signal-to-(noise + distortion) at the output of the ADC. The signal is the rms amplitude of the fundamental. Noise is the sum of all nonfundamental signals up to half the sampling frequency (fS/2, excluding dc). The ratio depends on the number of quantization levels in the digitization process: the more levels, the smaller the quantization noise. The theoretical signal-to-(noise + distortion) ratio for an ideal N-bit converter with a sine wave input is given by Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB Thus, for an 18-bit converter, this is 110.12 dB. Total Harmonic Distortion (THD) The ratio of the rms sum of the harmonics to the fundamental. For the AD7609, it is defined as THD (dB) = V2 + V3 + V4 + V5 + V6 + V7 + V8 + V9 2 20log 2 2 2 2 2 2 2 V1 where: V1 is the rms amplitude of the fundamental. V2 to V9 are the rms amplitudes of the second through ninth harmonics. Peak Harmonic or Spurious Noise The ratio of the rms value of the next largest component in the ADC output spectrum (up to fS/2, excluding dc) to the rms value of the fundamental. Normally, the value of this specification is determined by the largest harmonic in the spectrum, but for ADCs where the harmonics are buried in the noise floor, it is determined by a noise peak. Intermodulation Distortion With inputs consisting of sine waves at two frequencies, fa and fb, any active device with nonlinearities creates distortion products at sum and difference frequencies of mfa ± nfb, where m, n = 0, 1, 2, 3. Intermodulation distortion terms are those for which neither m nor n is equal to 0. For example, the second-order terms include (fa + fb) and (fa − fb), and the third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and (fa − 2fb). The calculation of the intermodulation distortion is per the THD specification, where it is the ratio of the rms sum of the individual distortion products to the rms amplitude of the sum of the fundamentals expressed in decibels (dB). Rev. B | Page 19 of 36 AD7609 Data Sheet Power Supply Rejection (PSR) Variations in power supply affect the full-scale transition but not the converter’s linearity. Power supply rejection is the maximum change in full-scale transition point due to a change in power supply voltage from the nominal value. The power supply rejection ratio is defined as the ratio of the power in the ADC output at full-scale frequency, f, to the power of a 200 mV p-p sine wave applied to the ADC VDD and VSS supplies of Frequency fS. PSRR (dB) = 10 log (Pf/PfS) where: Pf is equal to the power at Frequency f in the ADC output. PfS is equal to the power at Frequency fS coupled onto the VDD and VSS supplies. Channel-to-Channel Isolation Channel-to-channel isolation is a measure of the level of crosstalk between any two channels. It is measured by applying a full-scale, 10 kHz sine wave signal to all unselected input channels and determining the degree to which the signal attenuates in the selected channel with a 1 kHz signal. Common-Mode Rejection Ratio (CMRR) CMRR is defined as the ratio of the power in the ADC common-mode input at full-scale frequency, f, to the power in the output of a full-scale p-p sine wave applied to the commonmode voltage of VINX+ and VINX− of frequency, fS, CMRR (dB) = 20 log (Pf/PfS) where: Pf is equal to the power at Frequency f in the ADC input. PfS is equal to the power at Frequency fS in the ADC output. Rev. B | Page 20 of 36 Data Sheet AD7609 THEORY OF OPERATION CONVERTER DETAILS Analog Input Clamp Protection The AD7609 is a data acquisition system that employs a high speed, low power, charge redistribution successive approximation analog-to-digital converter (ADC) and allows the simultaneous sampling of eight true differential analog input channels. The analog inputs on the AD7609 can accept true bipolar input signals. The RANGE pin is used to select either ±10 V or ±5 V as the input range. The AD7609 operates from a single 5 V supply. Figure 32 shows the analog input structure of the AD7609. Each AD7609 analog input contains clamp protection circuitry. Despite a single 5 V supply operation, this analog input clamp protection allows for an input overvoltage up to ±16.5 V. The AD7609 can handle true bipolar input voltages. The logic level on the RANGE pin determines the analog input range of all analog input channels. If this pin is tied to a logic high, the analog input range is ±10 V for all channels. If this pin is tied to a logic low, the analog input range is ±5 V for all channels. A logic change on this pin has an immediate effect on the analog input range; however, there is a settling time of 80 μs typically, in addition to the normal acquisition time requirement. The recommended practice is to hardwire the RANGE pin according to the desired input range for the system signals. During normal operation, the applied analog input voltage should remain within the analog input range selected via the RANGE pin. A RESET pulse must be applied to the part to ensure the analog input channels are configured for the range selected. When in a power-down mode, it is recommended to tie the analog inputs together or both analog input pins (Vx+, Vx−) to GND. As per the Analog Input Clamp Protection section, the overvoltage clamp protection is recommended for use in transient overvoltage conditions, and should not remain active for extended periods. Stressing the analog inputs outside of these conditions may degrade the Bipolar Zero Code error and THD performance of the AD7609. CLAMP 1MΩ SECONDORDER LPF 09760-129 Vx– 1MΩ Figure 32. Analog Input Circuitry Figure 33 shows the current vs. voltage characteristic of the clamp circuit. For input voltages up to ±16.5 V, no current flows in the clamp circuit. For input voltages above ±16.5 V, the AD7609 clamp circuitry turns on and clamps the analog input to ±16.5 V. A series resister should be placed on the analog input channels to limit the current to ±10 mA for input voltages above ±16.5 V. In an application where there is a series resistance on an analog input channel, VINx+, a corresponding resistance is required on the VINx− channel (see Figure 34). If there is no corresponding resister on the Vx− channel, this results in an offset error on that channel. It is recommended that the input overvoltage clamp protection circuitry be used to protect the AD7609 against transient overvoltage events. It is not recommended to leave the AD7609 in a condition where the clamp protection circuitry is active (in normal or power-down conditions) for extended periods because this may degrade the bipolar zero code error performance of the AD7609. AV , VDRIVE = 5V 30 T CC A = 25°C 20 10 0 –10 –20 –30 –40 –50 –20 Analog Input Impedance The analog input impedance of the AD7609 is 1 MΩ. This is a fixed input impedance and does not vary with the AD7609 sampling frequency. This high analog input impedance eliminates the need for a driver amplifier in front of the AD7609 allowing for direct connection to the source or sensor. With the need for a driver amplifier eliminated, bipolar supplies can be removed from the signal chain, which are often a source of noise in a system. –15 –10 –5 0 5 10 15 20 SOURCE VOLTAGE (V) Figure 33. Input Protection Clamp Profile RFB AD7609 +10V –10V +10V –10V R R VINx+ C VINx– CLAMP CLAMP 1MΩ 1MΩ RFB Figure 34. Input Resistance Matching on the Analog Input Rev. B | Page 21 of 36 09760-033 Analog Input Ranges CLAMP 09760-031 ANALOG INPUT Vx+ RFB INPUT CLAMP CURRENT (mA) The AD7609 contains input clamp protection, input signal scaling amplifiers, a second-order antialiasing filter, track-andhold amplifiers, an on-chip reference, reference buffers, a high speed ADC, a digital filter, and high speed parallel and serial interfaces. Sampling on the AD7609 is controlled using CONVST x signals. RFB AD7609 Data Sheet Analog Input Antialiasing Filter An analog antialiasing filter is also provided on the AD7609. The filter is a second-order Butterworth. Figure 35 and Figure 36 show the frequency and phase response respectively of the analog antialiasing filter. In the ±5 V range, the −3 dB frequency is typically 23 kHz. In the ±10 V range, the −3 dB frequency is typically 32 kHz. 0 10V DIFF –5 5V DIFF –15 ADC TRANSFER FUNCTION –20 –25 TEMP –40°C 25°C 85°C –40°C 5V 25°C 85°C –30 10V –35 0.1dB 13,354Hz 12,769Hz 12,427Hz 10,303Hz 9619Hz 9326Hz –40 100 3dB 33,520Hz 32,397Hz 31,177Hz 24,365Hz 23,389Hz 22,607Hz 1k 10k FREQUENCY (Hz) 100k 09760-032 ATTENUATION (dB) –10 The conversion clock for the part is internally generated, and the conversion time for all channels is 4 µs on the AD7609. The BUSY signal returns low after all eight conversions to indicate the end of the conversion process. On the falling edge of BUSY, the track-and-hold amplifiers return to track mode. New data can be read from the output register via the parallel, or serial interface after BUSY goes low; or, alternatively, data from the previous conversion can be read while BUSY is high. Reading data from the AD7609 while a conversion is in progress has little effect on performance and allows a faster throughput to be achieved. With a VDRIVE > 3.3 V, the SNR is reduced by ~1.5 dB when reading during a conversion. The output coding of the AD7609 is twos complement. The designed code transitions occur midway between successive integer LSB values, that is, 1/2 LSB, 3/2 LSB. The LSB size is FSR/262,144 for the AD7609. The FSR for the AD7609 is 40 V for the ±10 V range and 20 V for the ±5 V range. The ideal transfer characteristic for the AD7609 is shown in Figure 37. V+ ± (V–) × 131,072 × 20V V+ ± (V–) ±5V CODE = × 131,072 × 10V ±10V CODE = Figure 35. Analog Antialiasing Filter Frequency Response REF 2.5V REF 2.5V 14 13 011...111 011...110 12 ADC CODE ±5V RANGE 9 8 000...001 000...000 111...111 LSB = +FSR – (–FSR) 218 ±10V RANGE 7 100...010 100...001 100...000 6 5 –FS + 1/2LSB 4 0V – 1LSB +FS – 3/2LSB ANALOG INPUT 3 Figure 37. AD7609 Transfer Characteristic AVCC, VDRIVE = 5V fSAMPLE = 200kSPS TA = 25°C 1 0 10 1k 10k INPUT FREQUENCY (Hz) 100k The LSB size is dependent on the analog input range selected (see Table 7). 09760-133 2 09760-034 PHASE DELAY (µs) 11 10 Table 7. Output Codes and Ideal Input Values Figure 36. Analog Antialiasing Filter Phase Response Track-and-Hold Amplifiers The track-and-hold amplifiers on the AD7609 allow the ADC to accurately acquire an input sine wave of full-scale amplitude to 18-bit resolution. The track-and-hold amplifiers sample their respective inputs simultaneously on the rising edge of CONVST x. The aperture time for track-and-hold (that is, the delay time between the external CONVST x signal and the track-and-hold actually going into hold) is well matched, by design, across all eight track-and-holds on one device and from device to device. This matching allows more than one AD7609 device to be sampled simultaneously in a system. Description FSR − 0.5 LSB Midscale + 1 LSB Midscale Midscale – 1 LSB −FSR + 1 LSB −FSR The end of the conversion process across all eight channels is indicated by the falling edge of BUSY; and it is at this point that the track-and-holds return to track mode and the acquisition time for the next set of conversions begins. Rev. B | Page 22 of 36 Analog Input (V+ − (V−) 10 V Range +19.99992 V +152.58 µV 0V −152.58 µV −19.99984 V −20 V Analog Input V+ − (V−) 5 V Range 9.999961 V 76 µV 0V −76 µV −9.99992 V −10 V Digital Output Code (Hex) 0x1FFFF 0x00001 0x00000 0x3FFFF 0x20001 0x20000 Data Sheet AD7609 INTERNAL/EXTERNAL REFERENCE REFIN/REFOUT SAR The AD7609 contains an on-chip 2.5 V band gap reference. The REFIN/REFOUT pin allows access to the 2.5 V reference that generates the on-chip 4.5 V reference internally, or it allows an external reference of 2.5 V to be applied to the AD7609. An externally applied reference of 2.5 V is also amplified to 4.5 V using the internal buffer. This 4.5 V buffered reference is the reference used by the SAR ADC. 10µF REFCAPA 09760-035 2.5V REF Figure 38. Reference Circuitry AD7609 AD7609 AD7609 REF SELECT REF SELECT REF SELECT REFIN/REFOUT REFIN/REFOUT REFIN/REFOUT 100nF 100nF 100nF When the AD7609 is configured in external reference mode, the REFIN/REFOUT pin is a high input impedance pin. For applications using multiple AD7609 devices, the following configurations are recommended depending on the application requirements. External Reference Mode One ADR421 external reference can be used to drive the REFIN/REFOUT pins of all AD7609 devices (see Figure 39). In this configuration, each AD7609 REFIN/REFOUT pin should be decoupled with a 100 nF decoupling capacitor. Internal Reference Mode One AD7609 device, configured to operate in the internal reference mode, can be used to drive the remaining AD7609 devices, which are configured to operate in external reference mode (see Figure 40). The REFIN/REFOUT pin of the AD7609, configured in internal reference mode, should be decoupled using a 10 µF ceramic decoupling capacitor. The other AD7609 devices, configured in external reference mode, should use a 100 nF decoupling capacitor on their REFIN/REFOUT pins. Rev. B | Page 23 of 36 09760-037 ADR421 0.1µF Figure 39. Single External Reference Driving Multiple AD7609 REFIN/REFOUT Pins VDRIVE AD7609 AD7609 AD7609 REF SELECT REF SELECT REF SELECT REFIN/REFOUT REFIN/REFOUT REFIN/REFOUT + 10µF 100nF 100nF Figure 40. Internal Reference Driving Multiple AD7609 REFIN Pins 09760-036 The REF SELECT pin is a logic input pin that allows the user to select between the internal reference and the external reference. If this pin is set to logic high, the internal reference is selected and is enabled; if this pin is set to logic low, the internal reference is disabled and an external reference voltage must be applied to the REFIN/REFOUT pin. The internal reference buffer is always enabled. After a reset, the AD7609 operates in the reference mode selected by the REF SELECT pin. Decoupling is required on the REFIN/REFOUT pin for both the internal or external reference options. A 10 µF ceramic capacitor is required on the REFIN/REFOUT to ground close to the REFGND pins. The AD7609 contains a reference buffer configured to amplify the REF voltage up to ~4.5 V, as shown in Figure 38. The REFCAPA and REFCAPB pins must be shorted together externally and a ceramic capacitor of 10 μF applied to REFGND to ensure the reference buffer is in closed-loop operation. The reference voltage available at the REFIN/REFOUT pin is 2.5 V. REFCAPB BUF AD7609 Data Sheet TYPICAL CONNECTION DIAGRAM POWER-DOWN MODES Figure 41 shows the typical connection diagram for the AD7609. There are four AVCC supply pins on the part that can be tied together and decoupled using a 100 nF capacitor at each supply pin and a 10 µF capacitor at the supply source. The AD7609 can operate with the internal reference or an externally applied reference. In this configuration, the AD7609 is configured to operate with the internal reference. When using a single AD7609 device on the board, the REFIN/REFOUT pin should be decoupled with a 10 µF capacitor. In an application with multiple AD7609 devices, see the Internal/External Reference section. The REFCAPA and REFCAPB pins are shorted together and decoupled with a 10 µF ceramic capacitor. There are two power-down modes available on the AD7609. The STBY pin controls whether the AD7609 is in normal mode or one of the two power-down modes. The two power-down modes available are standby mode and shutdown mode. The power-down mode is selected through the state of the RANGE pin when the STBY pin is low. Table 8 shows the configurations required to choose the desired power-down mode. When the AD7609 is placed in standby mode, the current consumption is 8 mA maximum and power-up time is approximately 100 µs because the capacitor on the REFCAPA/REFCAPB pins must charge up. In standby mode, the on-chip reference and regulators remain powered up and the amplifiers and ADC core are powered down. When the AD7609 is placed in shutdown mode, the current consumption is 11 µA maximum and power up time is about 13 ms. In shutdown mode, all circuitry is powered down. When the AD7609 is powered up from shutdown mode, a reset signal must be applied to the AD7609 after the required power-up time has elapsed. The VDRIVE supply is connected to the same supply as the processor. The voltage on VDRIVE controls the voltage value of the output logic signals. For layout, decoupling, and grounding hints, see the Layout Guidelines section. After supplies are applied to the AD7609, a reset should be applied to the AD7609 to ensure that it is configured for the correct mode of operation. Table 8. Power-Down Mode Selection STBY Power-Down Mode Standby Shutdown ANALOG SUPPLY VOLTAGE 5V1 1µF REFIN/REFOUT 100nF 100nF REGCAP2 AVCC VDRIVE REFCAPA 10µF DB0 TO DB15 + REFCAPB REFGND EIGHT DIFFERENTIAL ANALOG INPUT PAIRS V1+ V1– V2+ V2– V3+ V3– V4+ V4– V5+ V5– V6+ V6– V7+ V7– V8+ V8– AD7609 CONVST A, B CS RD BUSY RESET OS 2 OS 1 OS 0 REF SELECT PARALLEL INTERFACE OVERSAMPLING VDRIVE PAR/SER SEL RANGE STBY VDRIVE AGND 1DECOUPLING SHOWN ON THE AV CC PIN APPLIES TO EACH AVCC PIN (PIN 1, PIN 37, PIN 38, PIN 48). DECOUPLING CAPACITOR CAN BE SHARED BETWEEN AV CC PIN 37 AND PIN 38. 2DECOUPLING SHOWN ON THE REGCAP PIN APPLIES TO EACH REGCAP PIN (PIN 36, PIN 39). Figure 41. Typical Connection Diagram Rev. B | Page 24 of 36 09760-038 + DIGITAL SUPPLY VOLTAGE +2.3V TO +5V MICROPROCESSOR/ MICROCONVERTER/ DSP 10µF 0 0 RANGE 1 0 Data Sheet AD7609 Simultaneously Sampling Two Sets of Channels CONVERSION CONTROL The AD7609 also allows the analog input channels to be sampled simultaneously in two sets. This can be used in power line protection and measurement systems to compensate for phase differences between PT and CT transformers. In a 50 Hz system, this allows for up to 9° of phase compensation, and in a 60 Hz system, it allows for up to 10° of phase compensation. Simultaneous Sampling on All Analog Input Channels The AD7609 allows simultaneous sampling of all analog input channels. All channels are sampled simultaneously when both CONVST x pins (CONVST A, CONVST B) are tied together. A single CONVST x signal is used to control both CONVST x inputs. The rising edge of this common CONVST x signal initiates simultaneous sampling on all analog input channels. This is accomplished by pulsing the two CONVST x pins independently and is only possible if oversampling is not in use. CONVST A is used to initiate simultaneous sampling of the first set of channels (V1 to V4). CONVST B is used to initiate simultaneous sampling on the second set of analog input channels (V5 to V8), as illustrated in Figure 42. On the rising edge of CONVST A, the track-and-hold amplifiers for the first set of channels are placed into hold mode. On the rising edge of CONVST B, the track-and-hold amplifiers for the second set of channels are placed into hold mode. The conversion process begins after both rising edges of CONVST x have occurred; therefore, BUSY goes high on the rising edge of the later CONVST x signal. The falling edge of BUSY also indicates that the new data can now be read from the parallel bus or the serial data lines, DOUTA and DOUTB. There is no change to the data read process when using two separate CONVST x signals. The AD7609 contains an on-chip oscillator that is used to perform the conversions. The conversion time for all ADC channels is tCONV. The BUSY signal indicates to the user when conversions are in progress, so that when the rising edge of CONVST x is applied, BUSY goes logic high and transitions low at the end of the entire conversion process. The falling edge of the BUSY signal is used to place all eight track-and-hold amplifiers back into track mode. The falling edge of BUSY also indicates that the new data can now be read from the parallel bus (DB[15:0]) or the serial data lines, DOUTA and DOUTB. Connect all unused analog input channel to AGND. The results for any unused channels are still included in the data read because all channels are always converted. V1 TO V4 TRACK-AND-HOLD ENTER HOLD V5 TO V8 TRACK-AND-HOLD ENTER HOLD CONVST A t5 CONVST B AD7609 CONVERTS ON ALL 8 CHANNELS BUSY tCONV CS, RD V1 V2 V8 09760-039 DATA: DB[15:0] FRSTDATA Figure 42. Simultaneous Sampling on Channel Sets Using Independent CONVST A/CONVST B Signals—Parallel Mode Rev. B | Page 25 of 36 AD7609 Data Sheet DIGITAL INTERFACE The AD7609 provides two interface options: a parallel interface and a high speed serial interface. The required interface mode is selected via the PAR/SER SEL pin. AD7609 INTERRUPT BUSY 14 The operation of the interface modes is described in the following sections. DIGITAL HOST DB[15:0] 33:16 PARALLEL INTERFACE (PAR/SER SEL = 0) Data can be read from the AD7609 via the parallel data bus with standard CS and RD signals. To read the data over the parallel bus, the PAR/SER SEL pin should be tied low. The CS and RD input signals are internally gated to enable the conversion result onto the data bus. The data lines, DB15 to DB0, leave their high impedance state when both CS and RD are logic low. The rising edge of the CS input signal three-states the bus and the falling edge of the CS input signal takes the bus out of the high impedance state. CS is the control signal that enables the data lines; it is the function that allows multiple AD7609 devices to share the same parallel data bus. The CS signal can be permanently tied low, and the RD signal can be used to access the conversion results, as shown in Figure 4. A read operation of new data can take place after the BUSY signal goes low (Figure 2), or, alternatively, a read operation of data from the previous conversion process can take place while BUSY is high (Figure 3). The RD pin is used to read data from the output conversion results register. Two RD pulses are required to read the full 18-bit conversion result from each channel. Applying a sequence of 16 RD pulses to the AD7609 RD pin clocks the conversion results out from each channel onto the parallel output bus, DB[15:0], in ascending order. The first RD falling edge after BUSY goes low clocks out DB[17:2] of the V1 result, the next RD falling edge updates the bus with DB[1:0] of the V1 result. It takes 16 RD pulses to read the eight 18-bit conversion results from the AD7609. The 16th falling edge of RD clocks out the DB[1:0] conversion result for Channel V8. When the RD signal is logic low, it enables the data conversion result from each channel to be transferred to the digital host (DSP, FPGA). When there is only one AD7609 in a system/board and it does not share the parallel bus, data can be read using only one control signal from the digital host. The CS and RD signals can be tied together, as shown in Figure 5. In this case, the data bus comes out of three-state on the falling edge of CS/RD. The combined CS and RD signal allows the data to be clocked out of the AD7609 and to be read by the digital host. In this case, CS is used to frame the data transfer of each data channel and 16 CS pulses are required to read the eight channels of data. 09760-040 CS 13 RD 12 Figure 43. AD7609 Interface Diagram: One AD7609 Using the Parallel Bus; CS and RD Shorted Together SERIAL INTERFACE (PAR/SER SEL = 1) To read data back from the AD7609 over the serial interface, the PAR/SER SEL pin should be tied high. The CS and SCLK signals are used to transfer data from the AD7609. The AD7609 has two serial data output pins, DOUTA and DOUTB. Data can be read back from the AD7609 using one or both of these DOUT lines. For the AD7609, conversion results from Channel V1 to Channel V4 first appear on DOUTA, whereas conversion results from Channel V5 to Channel V8 first appear on DOUTB. The CS falling edge takes the data output lines (DOUTA and DOUTB) out of three-state and clocks out the MSB of the conversion result. The rising edge of SCLK clocks all subsequent data bits onto the serial data outputs, DOUTA and DOUTB. The CS input can be held low for the entire serial read or it can be pulsed to frame each channel read of 18 SCLK cycles. Figure 44 shows a read of eight simultaneous conversion results using two DOUT lines on the AD7609. In this case, a 72 SCLK transfer is used to access data from the AD7609 and CS is held low to frame the entire 72 SCLK cycles. Data can also be clocked out using only one DOUT line, in which case DOUTA is recommended to access all conversion data, because the channel data is output in ascending order. For the AD7609 to access all eight conversion results on one DOUT line, a total of 144 SCLK cycles are required. These 144 SCLK cycles can be framed by one CS signal or each group of 18 SCLK cycles can be individually framed by the CS signal. The disadvantage of using only one DOUT line is that the throughput rate is reduced if reading after conversion. The unused DOUT line should be left unconnected in serial mode. For the AD7609, if DOUTB is to be used as a single DOUT line, the channel results are output in the following order: V5, V6, V7, V8, V1, V2, V3, V4; however, the FRSTDATA indicator returns low after V5 is read on DOUTB. Rev. B | Page 26 of 36 Data Sheet AD7609 Figure 6 shows the timing diagram for reading one channel of data, framed by the CS signal, from the AD7609 in serial mode. The SCLK input signal provides the clock source for the serial read operation. CS goes low to access the data from the AD7609. The falling edge of CS takes the bus out of three-state and clocks out the MSB of the 18-bit conversion result. This MSB is valid on the first falling edge of the SCLK after the CS falling edge. The subsequent 17 data bits are clocked out of the AD7609 on the SCLK rising edge. Data is valid on the SCLK falling edge. Eighteen clock cycles must be provided to the AD7609 to access each conversion result. The FRSTDATA output signal indicates when the first channel, V1, is being read back. When the CS input is high, the FRSTDATA output pin is in three-state. In serial mode, the falling edge of CS takes FRSTDATA out of three-state and sets the FRSTDATA pin high indicating that the result from V1 is available on the DOUTA output data line. The FRSTDATA output returns to a logic low following the 18th SCLK falling edge. If all channels are read on DOUTB, the FRSTDATA output does not go high when V1 is being output on this serial data output pin. It only goes high when V1 is available on DOUTA (and this is when V5 is available on DOUTB). READING DURING CONVERSION Data can be read from the AD7609 while BUSY is high and conversions are in progress. This has little effect on the performance of the converter and allows a faster throughput rate to be achieved. A parallel or serial read can be performed during conversions and when oversampling may or may not be in use. Figure 3 shows the timing diagram for reading while BUSY is high in parallel or serial mode. Reading during conversions allows the full throughput rate to be achieved when using the serial interface with a VDRIVE of 3.3 V to 5.25 V. Data can be read from the AD7609 at any time other than on the falling edge of BUSY because this is when the output data registers are updated with the new conversion data. t6, outlined in Table 3, should be observed in this condition. CS 72 DOUTA V1 V2 V3 V4 DOUTB V5 V6 V7 V8 Figure 44. AD7609 Serial Interface with Two DOUT Lines Rev. B | Page 27 of 36 09760-041 SCLK AD7609 Data Sheet The CONVST A and CONVST B pins must be tied/driven together when oversampling is turned on. When the oversampling function is turned on, the BUSY high time for the conversion process extends. The actual BUSY high time depends on the oversampling rate selected; the higher the oversampling rate, the longer the BUSY high, or total conversion time, see Table 9. DIGITAL FILTER The AD7609 contains an optional digital filter. This digital filter is a first-order sinc filter. This digital filter should be used in applications where slower throughput rates are used or where higher signal-to-noise ratio or dynamic range is desirable. The oversampling ratio of the digital filter is controlled using the oversampling pins, OS [2:0] (see Table 9). OS 2 is the MSB control bit and OS 0 is the LSB control bit. Table 9 provides the oversampling bit decoding to select the different oversample rates. The OS pins are latched on the falling edge of BUSY. This sets the oversampling rate for the next conversion (see Figure 45). In addition to the oversampling function, the output result is decimated to 18-bit resolution. Figure 46 shows that the conversion time extends as the oversampling rate is increased, and the BUSY signal lengthens for the different oversampling rates. For example, a sampling frequency of 10 kSPS yields a cycle time of 100 μs. Figure 46 shows OS × 2 and OS × 4; for a 10 kSPS example, there is adequate cycle time to further increase the oversampling rate and yield greater improvements in SNR performance. In an application where the initial sampling or throughput rate is at 200 kSPS, for example, and oversampling is turned on, the throughput rate must be reduced to accommodate the longer conversion time and to allow for the read. To achieve the fastest throughput rate possible when oversampling is turned on, the read can be performed during the BUSY high time. The falling edge of BUSY is used to update the output data registers with the new conversion data; therefore, the reading of conversion data should not occur on this edge. Figure 47 to Figure 53 illustrate the effect of oversampling on the code spread in a dc histogram plot. As the oversample rate is increased, the spread of codes is reduced. (In Figure 47 to Figure 53, AVCC = VDRIVE = 5 V and the sampling rate was scaled with OS ratio.) If the OS pins are set to select an OS ratio of 8, the next CONVST x rising edge takes the first sample for each channel and the remaining seven samples for all channels are taken with an internally generated sampling signal. These samples are then averaged to yield an improvement in SNR performance. Table 9 shows typical SNR performance for both the ±10 V and the ±5 V ranges. As Table 9 indicates, there is an improvement in SNR as the OS ratio increases. As the OS ratio increases, the 3 dB frequency is reduced and the allowed sampling frequency is also reduced. In an application where the required sampling frequency is 10 kSPS, an OS ratio of up to 16 can be used. In this case, the application sees an improvement in SNR but the input −3 dB bandwidth is limited to ~6 kHz. CONVST A, CONVST B OVERSAMPLE RATE LATCHED FOR CONVERSION N + 1 CONVERSION N CONVERSION N + 1 BUSY tOS_HOLD 09760-042 tOS_SETUP OS x Figure 45. OS Pin Timing Table 9. Oversampling Bit Decoding (100 Hz Input Signal) OS [2:0] 000 001 010 011 100 101 110 111 OS Ratio No OS 2 4 8 16 32 64 Invalid SNR ±5 V Range (dB) 90.8 93.3 95.5 98 100.6 101.8 102.7 SNR ±10 V Range (dB) 91.5 93.9 96.4 98.9 101 102 102.9 −3 dB BW 5 V Range (kHz) 22 22 18.5 11.9 6 3 1.5 Rev. B | Page 28 of 36 −3 dB BW 10 V Range (kHz) 33 28.9 21.5 12 6 3 1.5 Maximum Throughput CONVST x Frequency (kHz) 200 100 50 25 12.5 6.25 3.125 Data Sheet AD7609 tCYCLE CONVST A, CONVST B tCONV 19µs 9µs 4µs OS = 0 BUSY OS = 2 OS = 4 t4 t4 t4 CS 09760-043 RD DATA: DB[15:0] Figure 46. AD7609—No Oversampling, Oversampling × 4, and Oversampling × 8 Using Read After Conversion 3000 1600 OVERSAMPLING BY 4 NO OVERSAMPLING 1384 1373 840 800 727 600 492 450 400 1500 1000 2 10 27 –9 –8 –7 –6 –5 –4 –3 –2 –1 0 1 CODE 2 3 4 5 32 11 2 6 8 9 7 1 0 5 49 –5 –4 –3 –2 –1 0 CODE 1 79 8 3 4 2 Figure 49. Histogram of Codes—OS × 4 (10 Codes) Figure 47. Histogram of Codes—No OS (19 Codes) 4000 2000 OVERSAMPLING BY 2 OVERSAMPLING BY 8 3392 3500 NUMBER OF OCCURRENCES 1600 1389 1400 1146 1200 1000 788 800 599 600 400 3000 2397 2500 2000 1568 1500 1000 317 214 12 –7 –6 –5 –4 –3 –2 –1 229 105 46 0 1 CODE 2 3 4 15 2 1 5 6 7 09760-045 1 549 500 200 0 1 41 –4 –3 15 –2 –1 0 1 2 CODE Figure 50. Histogram of Codes—OS × 8 (Eight Codes) Figure 48. Histogram Of Codes—OS × 2 (15 Codes) Rev. B | Page 29 of 36 3 09760-047 1785 1772 1800 NUMBER OF OCCURRENCES 422 341 100 83 0 1340 1191 500 219 210 200 2000 09760-046 NUMBER OF OCCURRENCES 1062 1000 0 2363 2394 2500 1167 1200 09760-044 NUMBER OF OCCURRENCES 1400 AD7609 Data Sheet When the oversampling mode is selected, this has the effect of adding a digital filter function after the ADC. The different oversampling rates and the CONVST x sampling frequency produces different digital filter frequency profiles. 4500 OVERSAMPLING BY 16 3833 3500 3279 3000 Figure 54 to Figure 59 show the digital filter frequency profiles for the different oversampling rates. The combination of the analog antialiasing filter and the oversampling digital filter can be used to eliminate or reduce the complexity of the design of the filter before the AD7609. The digital filtering combines steep roll-off and linear phase response. 2500 2000 1500 1000 0 657 385 406 500 0 –3 –2 –1 0 1 2 CODE 6000 OVERSAMPLING BY 32 5090 5000 –20 –30 –40 –50 –60 4000 –70 –80 2716 –90 100 2000 1k 10k 100k 1M 10M FREQUENCY (Hz) 09760-051 3000 Figure 54. Digital Filter Response for OS × 2 1000 341 0 –2 –1 0 1 CODE 09760-049 45 0 –20 ATTENUATION (dB) Figure 52. Histogram of Codes—OS × 32 (Four Codes) 7000 OVERSAMPLING BY 64 5871 6000 5000 AVCC = 5V VDRIVE = 5V TA = 25°C 10V RANGE OS BY 4 –10 –30 –40 –50 –60 –70 –80 4000 –90 3000 –100 100 2245 2000 1k 10k 100k 1M FREQUENCY (Hz) Figure 55. Digital Filter Response for OS × 4 1000 –2 –1 0 1 CODE 09760-050 75 1 0 Figure 53. Histogram of Codes – OS × 64 (Four Codes) Rev. B | Page 30 of 36 10M 09760-052 NUMBER OF OCCURENCES –10 ATTENUATION (dB) Figure 51. Histogram of Codes—OS × 16 (Six Codes) NUMBER OF OCCURENCES AVCC = 5V VDRIVE = 5V TA = 25°C 10V RANGE OS BY 2 14 3 09760-048 NUMBER OF OCCURENCES 4000 Data Sheet AD7609 –20 –20 ATTENUATION (dB) –30 –40 –50 –60 –70 –30 –40 –50 –60 –70 –80 –80 –90 –90 1k 10k 100k 1M 10M FREQUENCY (Hz) –100 100 09760-053 –100 100 –20 ATTENUATION (dB) –40 –50 –60 –70 –40 –50 –60 –70 –80 –90 –90 10k 100k 1M FREQUENCY (Hz) 10M –30 –80 1k 1M 10M AVCC = 5V VDRIVE = 5V TA = 25°C 10V RANGE OS BY 64 –10 –30 –100 100 100k 0 09760-054 ATTENUATION (dB) –20 10k Figure 58. Digital Filter Response for OS × 32 AVCC = 5V VDRIVE = 5V TA = 25°C 10V RANGE OS BY 16 –10 1k FREQUENCY (Hz) Figure 56. Digital Filter Response for OS × 8 0 AVCC = 5V VDRIVE = 5V TA = 25°C 10V RANGE OS BY 32 –10 09760-055 –10 ATTENUATION (dB) 0 AVCC = 5V VDRIVE = 5V TA = 25°C 10V RANGE OS BY 8 Figure 57. Digital Filter Response for OS × 16 –100 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 59. Digital Filter Response for OS × 64 Rev. B | Page 31 of 36 10M 09760-056 0 AD7609 Data Sheet LAYOUT GUIDELINES The printed circuit board that houses the AD7609 should be designed so that the analog and digital sections are separated and confined to different areas of the board. If the AD7609 is in a system where multiple devices require analog-to-digital ground connections, the connection should still be made at only one point, a star ground point, which should be established as close as possible to the AD7609. Good connections should be made to the ground plane. Avoid sharing one connection for multiple ground pins. Individual vias or multiple vias to the ground plane should be used for each ground pin. 09760-057 Use at least one ground plane. It can be common or split between the digital and analog sections. In the case of the split plane, the digital and analog ground planes should be joined in only one place, preferably as close as possible to the AD7609. Figure 60. Top Layer Decoupling REFIN/REFOUT, REFCAPA, REFCAPB, and REGCAP Pins The power supply lines to the AVCC and VDRIVE pins on the AD7609 should use as large a trace as possible to provide low impedance paths and reduce the effect of glitches on the power supply lines. Where possible, use supply planes. Good connections should be made between the AD7609 supply pins and the power tracks on the board; this should involve the use of a single via or multiple vias for each supply pin. Good decoupling is also important to lower the supply impedance presented to the AD7609 and to reduce the magnitude of the supply spikes. Place the decoupling capacitors close to, ideally right up against, these pins and their corresponding ground pins. Place the decoupling capacitors for the REFIN/ REFOUT pin and the REFCAPA and REFCAPB pins as close as possible to their respective AD7609 pins. Where possible, they should be placed on the same side of the board as the AD7609 device. Figure 60 shows the recommended decoupling on the top layer of the AD7609 board. Figure 61 shows bottom layer decoupling. Bottom layer decoupling is for the four AVCC pins and the VDRIVE pin. Rev. B | Page 32 of 36 09760-058 Avoid running digital lines under the devices because doing so couples noise onto the die. Allow the analog ground plane to run under the AD7609 to avoid noise coupling. Shield fastswitching signals like CONVST A, CONVST B, or clocks with digital ground to avoid radiating noise to other sections of the board, and they should never run near analog signal paths. Avoid crossover of digital and analog signals. Run traces on layers in close proximity on the board at right angles to each other to reduce the effect of feedthrough through the board. Figure 61. Bottom Layer Decoupling Data Sheet AD7609 09760-059 To ensure good device-to-device performance matching in a system that contains multiple AD7609 devices, a symmetrical layout between the AD7609 devices is important. Figure 62 shows a layout with two AD7609 devices. The AVCC supply plane runs to the right of both devices. The VDRIVE supply track runs to the left of the two AD7609 devices. The reference chip is positioned between both AD7609 devices and the reference voltage track runs north to Pin 42 of U1 and south to Pin 42 to U2. A solid ground plane is used. These symmetrical layout principles can be applied to a system that contains more than two AD7609 devices. The AD7609 devices can be placed in a north-to-south direction with the reference voltage located midway between the AD7609 devices and the reference track running in the north-to-south direction similar to Figure 62. Figure 62. Multiple AD7609 Layout, Top Layer and Supply Plane Layer Rev. B | Page 33 of 36 AD7609 Data Sheet OUTLINE DIMENSIONS 0.75 0.60 0.45 12.20 12.00 SQ 11.80 1.60 MAX 64 49 1 48 PIN 1 10.20 10.00 SQ 9.80 TOP VIEW (PINS DOWN) 0.15 0.05 0.20 0.09 7° 3.5° 0° SEATING PLANE 16 0.08 COPLANARITY VIEW A 33 32 17 VIEW A 0.50 BSC LEAD PITCH 0.27 0.22 0.17 ROTATED 90° CCW COMPLIANT TO JEDEC STANDARDS MS-026-BCD 051706-A 1.45 1.40 1.35 Figure 63. 64-Lead Low Profile Quad Flat Package [LQFP] (ST-64-2) Dimensions shown in millimeters ORDERING GUIDE Model 1 AD7609BSTZ AD7609BSTZ-RL EVAL-AD7609EDZ CED1Z 1 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 64-Lead Low Profile Quad Flat Package [LQFP] 64-Lead Low Profile Quad Flat Package [LQFP] Evaluation Board for the AD7609 Converter Evaluation Development Z = RoHS Compliant Part. Rev. B | Page 34 of 36 Package Option ST-64-2 ST-64-2 Data Sheet AD7609 NOTES Rev. B | Page 35 of 36 AD7609 Data Sheet NOTES ©2011–2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09760-0-5/14(B) Rev. B | Page 36 of 36