CCM03 MK II A new range of CCM03 connectors have been developed to interface with SIM/SAM cards as defined by GSM1111 and ENV1375-1. The connectors are available with either hinged covers or fixed covers and have been designed to minimize the amount of space needed for PCB mounting. Features Hinged Cover • Available with 6 or 8 contacts, with or without PCB locating pegs. Construction Contacts Plating Copper alloy Contact area : Gold alloy inlay or gold over nickel Terminals : Tin lead (2µ min) High temp. thermoplastic UL 94V-0 rated Stainless steel Moldings Slide lock/metal cover Mechanical Data Number of Contacts Mechanical life, hinged cover Mechanical life, fixed cover Card insertion force • Available with insulated card presence Card extraction force switch. • The cover springs open when unlocked while the card is in place. Contact force Slide locking force Vibration • The molding is polarized so that the cover can only be closed if the card is Shock correctly inserted. • The cover can be replaced without removing the connector from the PCB. Contact Electrical Data • Inspection slots allow an electrical test to be made without opening the cover. • The overall height of the connector is only 2,5 mm. The amount of space needed to mount the connector is just 29,65 mm x 17,2 mm. Fixed Cover • Available with 6 or 8 contacts. • The overall height of the connector is 2,85 mm max. Only 25,5 mm x 17,2 mm of board space is required to mount the connector. General • With tape and reel packaging as standard, the connectors are designed to be automatically pick-and-placed. • The high temperature thermoplastic moldings are suited for infrared and convection soldering processes. Insulation resistance Resistance Current rating Dielectric strength 6 or 8 10,000 cycles min 50,000 cycles Hinged cover: 1 N max Fixed cover: 3 N max Hinged cover: 1 N max Fixed cover: 0.80 N min / 3 N max 0.25 N min / 0.50 N max 2 N min / 6 N max Frequency 10 to 500 Hz. Acceleration 50m/s2 Duration 6 hours - amplitude 0,35 mm Max electrical discontinuity 1µs Peak value 500 m/s2 – Duration 11 ms 3 shocks in each direction of each axis Max electrical discontinuity 1 µs 1,000 MΩ min 100 mΩ max 10 µA min / 1 A max 750 Vrms min Switch Electrical Data Card detection switch Contact resistance Dielectric strength Current rating Maximum power Normally open 100 mΩ max 250 Vrms min 1 mA min / 10m A max 0.2 VA Environmental Data Operating temperature Soldering temperature -40°C to +85°C Temperature/time profile acc. to CECC00802 para. 6.1, Fig. 3 with peak temperature 250°C IEC 512 test number 11c (10 days) IEC 512 test number 11f (96 hours) Damp heat Salt mist Packaging Quantity per reel, see table next page. • By using an inlay finish in the contact area the life of the precious metal is extended by over 10 times that of standard gold plating. • Robustly formed printed circuit tails allow a co-planarity of ± 0,05 mm to be maintained. Dimensions are shown in mm Dimensions subject to change www.ittcannon.com 19 CCM03 MK II Ordering Code Part Number CCM03-3001 CCM03-3002 CCM03-3003 CCM03-3004 CCM03-3009 CCM03-3010 CCM03-3011 CCM03-3012 CCM03-3013 CCM03-3514 R102 R102 R102 R102 R102 R102 R102 R102 R102 R122 Number of Contacts 6 6 8 8 6 6 8 8 6 6 8 6 CCM03-3504 R122 CCM03-3505 R122 Cover Hinged Hinged Hinged Hinged Hinged Hinged Hinged Hinged Hinged Hinged PCB Locating Pegs No Yes No Yes No Yes No Yes No No Quantity per reel 1000 1000 1000 1000 1000 1000 1000 1000 1000 1200 Contact Finish Inlay Inlay Inlay Inlay Gold Gold Gold Gold Gold Inlay Switch lock No No No No No No No No No Yes Fixed Fixed No No 1200 1200 Inlay Inlay No No Card Presence switch No No No No No No No No Yes (insulated) No No No Dimensional Drawings MICROSIM CARD 25 2,5 (2,7 max. includes solder tails) Hinged Cover CCM03 - 3001 (6 contacts) 3002 (6 contacts - PCB locating pegs) 3003 (8 contacts) 3004 (8 contacts - PCB locating pegs) 180˚max SEE DETAIL A 25,5 (REF.) DETAIL A 0 0,1-0,1 29,65 5,65±0,2 13,8 2,45 R 1,9 1,25 0,8 0,65 3,5 28 ,4 1,25 1,25 25˚0' 25 ,4 ±0 ,2 4 0, Mated condition 3,81 3,81 0,7 Slider locked Notes: Coplanarity of soldering surfaces: ± 0,05 mm *Pegs: Height 0,7 mm and Ø 1 mm 25,5 (REF.) Pick and place area ø3,5 17,2 11,35 Bump XX-XXX Date Code area 3,81 3,8 R 1,9 PCB Layout CCM03-3001 / 3002 CCM03-3003 / 3004 (Component side) (Component side) 23,2 1,5 20,32 Pad ø0,1 1,27 1,3 0,2 1,5 5,5 3,81 3,81 1,55 6,35 C5 C6 C7 C8 Prohibited area Contact location according to ENV1375-1 & GSM11-11 9,34 C1 C2 C3 C4 1,3 C1 C2 C3 6x 8,6 C5 C6 C7 2x 2,54 5,08 1,27 10,16 Prohibited area Current location according to ENV1375-1 & GSM11-11 2,5 5,5 1,8 2,5 5,5 0,2 5,5 Pad 23,2 0,8 x 1 1,8 Contact foot area 0,8 x 1 1,5 1,44 2x 3,81 3,81 9,34 8x +0,1 ø1,2 0 8,6 Plastic outline Plastic outline 3x 2,54 1,5 25,5 25,5 Unless otherwise stated, tolerances are ± 0,10 mm Dimensions are shown in mm Dimensions subject to change www.ittcannon.com 20 CCM03 MK II Hinged Cover Insulated Card Presence Switch Dimensional Drawings Hinged Cover CCM03 - 3013 (6 contacts + Card Presence Switch) 25,5 ±0,2 0,4 MICROSIM CARD 25 A 1,27 13,15 3x 2,54 2,1 ,2 25 ,4 ±0 0,3 A 3,7 1 8,6 9,6 4 0, 8x Mated condition 25˚0' SEE DETAIL A 2,45 1,25 Plastic actuator 0,8 0,65 R 1,9 Slider locked DETAIL insulated blade switch 0 0,1-0,1 13,8 3,5 28 25,5 (REF.) DETAIL A 29,65 5,65 ±0,2 ,4 3,81 3,81 1,25 0,7 1,25 2,5 (2,7 max. includes solder tails) 180˚max 25,5 (REF.) 3,81 15 11,35 Pick and place area ø 3,5 17,2 XX-XXX 3,8 Date Code area R 1,9 Note: Coplanarity of soldering surfaces: ± 0,05 mm PCB Layout CCM03 - 3013 (6 contacts + Card Presence Switch) (Component side) Plastic outline Contact foot area 0,8 x 1 1,5 23,2 5,5 1,5 5,5 1,55 Prohibited area Contact location according to ENV1375-1 & GSM11-11 3,81 3,81 9,34 0,2 1,3 C1 C2 C3 SW 8x C5 C6 C7 SW 3x 2,54 1,27 8,6 1,8 Pad 2,5 25,5 Unless otherwise stated, tolerances are ± 0,10 mm Dimensions are shown in mm Dimensions subject to change www.ittcannon.com 21 CCM03 MK II Hinged Cover Dimensional Drawings Hinged Cover CCM03 - 3514 (6 contacts - with switch on metal lock) 25,5 ±0,2 Right lock switch terminal 13,15 MICROSIM CARD 25 A 5,08 0,6 3,7 180˚max Left lock switch terminal 25 ,4 8x ±0 ,2 0,3 4 0, 3,81 3,81 25,5 (REF.) 1,25 25˚0' SEE DETAIL A 28 ,4 Mated condition 0,7 1,25 DETAIL A on contacts & left lock switch terminal on right lock switch terminal only 0,65 29,65 5,65 ±0,2 13,8 2,45 R 1,9 1,25 0,8 +0,1 0,5 0 3,5 Slider locked 0,1 0,45 0 3 (3,2 max includes solder tails) 8,6 9,6 A 1,27 2x 2,54 5,08 2,1 0,4 25,5 (REF.) Pick and place area ø3,5 15 11,35 17,2 Bump XX-XXX Date Code area 3,81 3,8 R 1,9 Note: Coplanarity of soldering surfaces: ± 0,05 mm PCB Layout CCM03 - 3514 (6 contacts - with switch on metal lock) (Component side) Plastic outline 1,5 23,2 Contact foot area 0,8 x 0,6 2,4 3,4 2,5 1,5 5,5 7,6 1,55 1 0,2 8x 3 2x 2,54 1,27 Prohibited area Contact location according to ENV1375-1 & GSM11-11 C1 C2 C3 1,4 5,08 C5 C6 C7 5,08 8,6 1,8 Pad 5,5 5,6 3,81 3,81 9,34 25,5 Unless otherwise stated, tolerances are ± 0,10 mm Dimensions are shown in mm Dimensions subject to change www.ittcannon.com 22 CCM03 MK II Fixed Cover Dimensional Drawings Fixed cover CCM03 - 3504 (8 contacts) 12,7 3x 2,54 12,75 2,5 1 8,6 2,54 2,85 (3 max includes solder tails) A 1,27 25,5 ±0,2 1,25±0,05 2,65 12,1 30˚0' 25,5 B Pick and place area ø3,5 0,2 40˚0' 3,45 (REF.) 9,75 (REF.) 0 0,1-0,1 0,4 0,4 SEE DETAIL A 2,45 0,3 0,8 8x Mated condition 3,81 3,81 17,2 (REF.) A 0,3±0,02 DETAIL A 10,16 25,5 (REF.) 0,8 25,5 (REF.) 0,15 min Card stop A A 1,9 17,2 ±0,05 15,2 +0,1 0 +0,05 ø1,4 0 XX-XXX ø1,6 Date Code area 0,75 2,3 B 1,4+0,05 0 12,9 21,55 Note: Coplanarity of soldering surfaces: ± 0,05 mm PCB Layout CCM03 - 3504 CCM03 - 3505 (Component side) (Component side) ENV1375-1 & GSM11-11 25,5 3,81 6,35 5,5 1,44 C1 C6 C2 C7 C3 C8 C4 Prohibited area Contact location according to ENV1375-1 & GSM11-11 12,7 C5 1,3 8,6 1,27 6x Prohibited area 3,81 1,5 +0,05 ø1,4 0 2x 2,5 5,5 3x 2,54 C3 12,7 C2 C7 1,3 C6 0,2 8,6 C1 2x 2,54 1,27 C5 23,2 2,54 1,44 1,8 5,5 1,5 Contact foot area 0,8 x 1 Pad 0,2 Contact foot area 0,8 x 1 Pad Plastic outline 1,5 +0,05 ø1,4 0 2x 2,5 5,5 8x 23,2 1,8 1,5 2,54 Plastic outline 3,81 3,81 6,35 25,5 Unless otherwise stated, tolerances are ± 0,10 mm Dimensions are shown in mm Dimensions subject to change www.ittcannon.com 23 CCM03 MK II with Auto Lock cover A new range of CCM03 connectors have been developed to interface with SIM/SAM cards as defined by GSM1111 and ENV1375-1. The connectors are available with a hinged metallic cover and have been designed to provide an easier open/lock function and side card entry. Features • Available with 6 cross contacts which are designed to give a consistently reliable normal force over the life of the connector. • The hinged metallic cover can automatically lock by pressure. • Side entry of the card ensures easier positioning of the card into the connector. • Insulated blade switch version available for detection card when cover is closed. • The molding is polarized so that the cover can only be closed if the card is correctly inserted. • Inspection slots allow an electrical test to be made without opening the cover. • With tape and reel packaging as standard, the connectors are designed to be automatically pick-and-placed. • The moldings are made from hightemperature thermoplastics suited to infrared and convection soldering processes. • Robustly formed printed circuit tails allow a coplanarity of ± 0,05 mm to be maintained. Construction Contacts Contacts finish PC tail plating Molding Cover Copper alloy Gold over nickel Tin lead (2µ min) High temp. thermoplastic, UL94V-0 Stainless steel Mechanical Data Number of Contacts Mechanical life Contact force Vibration 6 10,000 cycles min 0.35 N min / 0.50 N max Frequency 10 to 500 Hz. Acceleration 50m/s2 Duration 6 hours - amplitude 0.35 mm (0.014) Max electrical discontinuity 1µs Contact Electrical Data Insulation resistance Resistance Current rating Dielectric strength 1,000 MΩ min 100 mΩ max 10 µA min / 1 A max 750 Vrms min Switch Electrical Data Card detection switch Contact resistance Dielectric strength Current rating Maximum power Normally open 100 mΩ max 250 Vrms min 1mA min / 10m A max 0.2 VA Environmental Data Operating temperature Soldering temperature -40°C to +85°C Temperature/time profile acc. to CECC00802 para. 6.1, Fig. 3 with peak temperature 250°C IEC 512 test number 11c (10 days) IEC 512 test number 11f (96 hours) Damp heat Salt mist Ordering Code Part Number CCM03-3517 CCM03-3518 CCM03-3529 Number of Contacts 6 6 6 Cover Side Hinged Front Hinged Front Hinged Card Presence Switch No Yes (insulated) No Quantity per reel 1300 1300 1300 Packaging 5 reels per box. Dimensions are shown in mm Dimensions subject to change www.ittcannon.com 24 CCM03 MK II with Auto Lock cover Dimensional Drawings Hinged Cover CCM03 - 3517 (6 contacts) 24,6±0,2 0,25 LOCKED UNLOCKED 1 3,23 8,82 8,64 A 1,27 2x 2,54 1,3 12,05 A 5 2 max. 2,2 1,8 +0,05 0,1-0,10 1,85 1,3 0,9 2,1 max on metal cover 0,3 6x 2,5 max 4,9 DETAIL A LOCKED UNLOCKED DETAIL A 1 Pick and place area ø3,2 24,6 (REF.) 0,95 0,95 29,6 Date Code area OPEN OPEN 1,9 Manual 1 opening 17 7 Manual 2 closing Card withdrawal from the base Card insertion 1 onto the base 14,5 2 0,9 2 0,9 xx-xxx 11,61 0,25 29,1 CARD INSERTION CARD WITHDRAWAL 0,25 Note: Coplanarity of soldering surfaces: ± 0,05 mm PCB Layout CCM03 - 3517 (6 contacts) (Component side) Plastic outline Contact foot area 1x1 Pad 1,5 22,1 2,5 1,5 1,25 5,5 C2 C7 C3 1,4 C1 C6 0,2 C5 Prohibited area Contact location according to ENV1375-1 & GSM 11-11 6x 5 1,27 2x 2,54 2,5 8,82 1,8 5,5 2 16,1 11,1 3,81 3,81 2 8,24 24,6 Unless otherwise stated, tolerances are ± 0,10 mm Dimensions are shown in mm Dimensions subject to change www.ittcannon.com 25 CCM03 MK II with Auto Lock cover Dimensional Drawings Hinged Cover CCM03 - 3518 (6 contacts and switch) 24,6±0,2 11,8 0,5 A 8,45 11,17 3x 2,54 11,8 1,27 5,1 1 OPEN UNLOCKED 2,86 0,3 A LOCKED 8x UNLOCKED Manual 1 opening 25,2 2,2 max (on metal cover) Plastic actuator 2 LOCKED Card withdrawal from the base 2,8 SEE DETAIL A +0,05 0,1-0,1 2,1 max (on insulator) DETAIL A Insulated blade switch 2 1 Blade switch 29,65 24,6 (REF.) Date Code area OPEN Manual 2 closing 17 10,5 2,4 18 max during opening Pick and place area ø3,2 Card insertion 1 onto the base 2,3 4,4 3,2 4,4 OPEN 0,95 Note: Coplanarity of soldering surfaces: ± 0,05 mm PCB Layout CCM03 - 3518 (6 contacts and switch) CCM03-3529 (without switch) layout is similar except SW pads CARD WITHDRAWAL 1,5 Pad 22,1 5 5,5 2,5 1,5 5,5 1,7 C1 C2 2 2x 3x 2,54 C3 SW SW 8x 19,1 1,27 Contact location according to ENV1375-1 & GSM 11-11 Prohibited area C7 1,4 C5 C6 0,2 8,45 1,8 1,05 CARD INSERTION (Component side) Plastic outline Contact foot area 1 x 1 3,81 3,81 7,24 24,6 Unless otherwise stated, tolerances are ± 0,10 mm Dimensions are shown in mm Dimensions subject to change www.ittcannon.com 26