P-511-523(V :1) E D060S C 4 V ers ion : 1.0 T E C HNIC AL S P E C IF IC AT ION MODE L NO : E D060S C 4 T he content of this information is s ubject to be changed without notice. P leas e contact P V I or its agent for further information. C us tomer•s C onfirmation C us tomer Date By P V I•s C onfirmation FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA, 92656 Http://www.AZDISPLAYS.com Confirmed B y Prepared B y T he information contained herein is the exclus ive property of P rime V iew International C o., Ltd. and s hall not be dis tributed, reproduced, or dis clos ed in whole or in part without prior written permis s ion of P rime V iew International C o., Ltd. P AG E :1 P-511-523(V:1) ED060SC4 Revision History Rev. 1.0 Issued Date May,13,2008 Revised New Contents The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:2 P-511-523(V:1) ED060SC4 TECHNICAL SPECIFICATION CONTENTS NO. ITEM PAGE - Cover 1 - Revision History 2 - Contents 3 1 Application 4 2 Features 4 3 Mechanical Specifications 4 4 Mechanical Drawing of EPD module 5 5 Input/Ouput Terminals 6 6 Electrical Characteristics 8 7 Power on Sequence 11 8 Optical Characteristics 13 9 Handing, Safety and Environment Requirements 16 10 Reliability test 17 11 Block Diagram 19 12 Packing 20 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:3 P-511-523(V:1) ED060SC4 1. Application The display is a TFT active matrix electrophoretic display, with associated interface and control logic, and a reference system design. The 6” active area contains 800x600 pixels, and has full 1~4 bit display capabilities. An integrated circuit containing interface, timing and control logic is supplied with each panel. 2. Features High contrast TFT electrophoretic 800x600 display High reflectance Ultra wide viewing angle Ultra low power consumption Pure reflective mode Bi-stable Commercial temperature range Landscape, portrait mode Antiglare hard-coated front-surface 3. Mechanical Specifications Parameter Screen Size Display Resolution Active Area Pixel Pitch Pixel Configuration Outline Dimension Module Weight Specifications 6.0 (4:3 diagonal) 800 (H) ͪ600(V) 122.4 (H)ͪ90.6 (V) 0.153 (H)ͪ0.151 (V) Rectangle Unit Inch Dot mm mm Remark Panel height is 137.90(W)Ø104.10(H)Ø1.18(D) (panel area height) mm measured without 137.90(W)Ø104.10(H)Ø2.0 (D) (FPC area height with capacitor) released film 35̈́5 g The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:4 P-511-523(V:1) ED060SC4 4. Mechanical Drawing of EPD Module The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:5 P-511-523(V:1) ED060SC4 5.Input/Ouput Interface 5-1)Pin Assignment Pin # Signal Description 1 VNEG Negative power supply source driver 2 VPOS Positive power supply source driver 3 VSS Ground 4 VDD Digital power supply drivers 5 CL Clock source driver 6 LE Latch enable source driver 7 OE Output enable source driver 8 SHR Shift direction source driver 9 NC NO Connection 10 NC NO Connection 11 SPH Start pulse source driver 12 D0 Data signal source driver 13 D1 Data signal source driver 14 D2 Data signal source driver 15 D3 Data signal source driver 16 D4 Data signal source driver 17 D5 Data signal source driver 18 D6 Data signal source driver 19 D7 Data signal source driver 20 NC NO Connection 21 NC NO Connection 22 VCOM Common connection 23 GVDD Positive power supply gate driver 24 GVEE Negative power supply gate driver 25 NC NO Connection 26 NC NO Connection 27 GMODE2 Output mode selection gate driver 28 GMODE1 Output mode selection gate driver 29 RL Shift direction gate driver 30 U1CE2 Cascade sequence 1st gate driver 31 U1CE1 Cascade sequence 1st gate driver 32 U1SPV Start pulse 1st gate driver 33 U1CKV Clock 1st gate driver 34 VBORDER Border connection 35 U2CE2 Cascade sequence 2nd gate driver 36 U2CE1 Cascade sequence 2nd gate driver 37 U2SPV Start pulse 2nd gate driver 38 U2CKV Clock 2nd gate driver 39 NC NO Connection The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:6 P-511-523(V:1) ED060SC4 5-2 )Panel Electrical Connection SERVICE CONNECTOR TYPE NUMBER Interface JST 39FXL-RSM1-S-H-TB NUMBER MATING OF PINS CONNECTOR 39 Copper foil 0.3mm pitch The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:7 P-511-523(V:1) ED060SC4 6.Electrical Characteristics 6-1) Panel interface description This panel is driven by ASIC PVI-6001A or “Apollo” display controller ASIC. See control product specification for details. 6-2) Panel DC characteristics Parameter Signal ground Symbol VSS VDD Logic Voltage supply IVDD GVEE Gate Negative supply GIEE GVDD Gate Positive supply GIDD VNEG Source Negative supply INEG VPOS Source Positive supply IPOS Asymmetry source Common voltage Maximum power panel Standby power panel Typical power panel Operating temperature Storage temperature Maximum image update time at 25к VAsym VCOM ICOM PMAX PSTBY PTYP Conditions VDD=3.3V GVEE =-20V GVDD = 22V VNEG = -15V VPOS = 15V VPOS+VNEG Min 3.0 -21 21 -15.4 14.6 - Typ 0 3.3 0.55 -20 Max 3.6 1.1 -19 1.3 22 3.9 23 0.6 -15 1.8 -14.6 18 15 36 15.4 18 36 Unit V V mA V mA V mA V mA V mA -80 -2.5 - 0 Adjusted 0.2 80 -1.0 - mV V mA - 1000 1100 mW 400 0.4 - mW mW 0 - 50 -25 - 70 к - 1000 - ms к - The maximum power and maximum currents are specified for the worst case power consumption. - The typical power is measured when “typical images” are displayed - The standby power is the consumed power when the panel controller is in standby mode. - The listed electrical/optical characteristics are only guaranteed under the controller & waveform provided by PVI. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:8 P-511-523(V:1) ED060SC4 6-3 )Panel AC characteristics VDD=3.0V to 3.6V, unless otherwise specified. Parameter Symbol Clock frequency Minimum “L” clock pulse width Clock rise time Clock fall time Data setup time Data hold time Pulse rise time Pulse fall time Clock CL cycle time D0 .. D7, SPH setup time D0 .. D7, SPH hold time LE on delay time LE high-level pulse width LE off delay time fckv twL trckv tfckv tSU tH trspv tfspv tcy tsu th tLEdly tLEw tLEoff Min. Typ. Max. Unit 200 kHz us ns ns ns ns ns ns ns ns ns ns ns Ns 0.5 100 100 100 100 100 100 DC 50 8 1 40 40 40 App Pin CKV CKV, SPV SPV Below table CLOCK & DATA TIMING CL tLEoff tLEdly LE tLE tOUT OUT1 ~ OUT400 OUTPUT LATCH CONTROL SIGNNALS SPH tstls tstlh 10% 10% CL tcy D0~D7 90% 90% 10% 10% tsu th The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:9 P-511-523(V:1) ED060SC4 6-4) Power Consumption Parameter Maximum panel power consumption during update. Power consumption in standby mode Symbol Typical panel power Conditions TYP Max Unit - - - 1100 mW - - - 0.4 mW - - 400 - mW Remark The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:10 P-511-523(V:1) ED060SC4 7.Power on Sequence 1. VSS VDD VNEG VPOS (Source driver) 2. VEE VGG(Gate driver) ϠPower on sequence’s timing chart as blew : VGG VPOS VDD VSS VEE V NEG Logic signal input The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:11 P-511-523(V:1) ED060SC4 ϠIt is expanded as blew. VDD Sequence VPOS Sequence VNEG VEE Sequence Sequence VGG Sequence Logic signal input Sequence The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:12 P-511-523(V:1) ED060SC4 8. Optical characteristics 8-1)Specifications Measurements are made with that the illumination is under an angle of 30 degrees, the detection is perpendicular unless otherwise specified. T = 25oC SYMBOL PARAMETER CONDITIONS MIN TYP. MAX UNIT R Reflectance White 30 35 - % Note 8-1 Gn Nth Grey Level - - DS+(WS-DS)ͪn/(m-1) - L* - CR Contrast Ratio - 6 - - Tupdate Update time 2~4-bit mode 1-bit mode 1000 540 - ms ms - WS: White state , DS: Dark state, Gray state from Dark to White :DSΕG1ΕG2…ΕGn…ΕGm-2ΕWS m:4Ε8Ε16 when 2Ε3Ε4 bits mode 8-2)Definition of contrast ratio The contrast ratio (CR) is the ratio between the reflectance in a full white area (Rl) and the reflectance in a dark area (Rd): CR = Rl/Rd The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:13 P-511-523(V:1) ED060SC4 Note 8-1 Luminance meter: Eye-One Pro Spectrophotometer Only reflectivity effect is counted when using above optical measurement with Eye-One Pro Spectrophotometer .Some scattering effect will be counted in actual visual conditions and the measurement data will be higher. A second optical measurement method and related data by which scattering effect counted are listed for reference. O ptical P roperties M easurem ent S etup Method Reflectivity only Reflectivity & scattering SYMBOL PARAMETER CONDITIONS MIN. R Reflectance White 30 Luminance meter Eye-One Pro Spectrophotometer R Reflectance White 35 EOTS UNIT % The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:14 P-511-523(V:1) ED060SC4 8-3)Reflection Ratio The reflection ratio is expressed as: R = Reflectance Factorwhite board x ( Lcenter / Lwhite board ) Lcenter is the luminance measured at center in a white area (R=G=B=1). Lwhite board is the luminance of a standard white board. Both are measured with equivalent illumination source (see figure 8.3). The viewing angle shall be no more than 2 degrees. figure 8.3 α = declination / θ = azimuth 8-4)Waveform - Wave Form file should be available before panel delivery to customer. Wave Form file size should be 64Kb Ghosting quality is measured by the reflectance difference between specific area and surface. In MU and GU mode, within 3L* In GC mode, within 2L* The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:15 P-511-523(V:1) ED060SC4 9.HANDLING, SAFETY AND ENVIROMENTAL REQUIREMENTS WARNING The display glass may break when it is dropped or bumped on a hard surface. Handle with care. Should the display break, do not touch the electrophoretic material. In case of contact with electrophoretic material, wash with water and soap. CAUTION The display module should not be exposed to harmful gases, such as acid and alkali gases, which corrode electronics components. Disassembling the display module can cause permanent damage and invalidates the warranty agreements. Observe general precautions that are common to handling delicate electronic components. The glass can break and front surfaces can easily be damaged. Moreover the display is sensitive to static electricity and other rough environmental conditions. Data sheet status Product This data sheet contains final product specifications. specification Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:16 P-511-523(V:1) ED060SC4 10. Reliability test ʳ TEST 1 High-Temperature Operation 2 Low-Temperature Operation 3 High-Temperature T = +60°C, RH=26% for 240 Functional hrs IEC 60 068-2-2Bp 4 Low-Temperature Functional IEC 60 068-2-2Ab 5 High-Temperature T = +70°C, RH=23% for 240 hrs Storage IEC 60 068-2-2Bp 6 Low-Temperature Storage T = -25°C for 240 hrs IEC 60 068-2-1Ab T = +40°C, RH = 90% for 168 hrs IEC 60 068-2-3CA T = +60к, RH=80% 240hrs IEC 60 068-2-3CA 7 8 High-Temperature, High-Humidity Operation High Temperature, High- Humidity Storage CONDITION METHOD T = +50°C, RH = 30% 240 hrs for IEC 60 068-2-2Bp IEC 60 068-2-2Ab T = 0°C for 240 hrs T = -10°C for 240 hrs for 9 Temperature Cycle 1 cycle:[-25к 30min]Ш[+70 к 30 min] : 100 cycles IEC 60 068-2-14 10 UV exposure Resistance 765 W/m2 for 168hrs,40к IEC60 068-2-5Sa Package Vibration 1.04G, Frequency: 10~500Hz Direction: X,Y,Z Duration: 1 hours in each direction Full packed for shipment 11 REMARK At the end of the test, electric, mechanical, and optical specifications shall be satisfied. At the end of the test, electric, mechanical, and optical specifications shall be satisfied. At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ At the end of the test, electric, mechanical, and optical specifications shall be satisfied.ʳ At the end of the test, electric, mechanical, and optical specifications shall be satisfied.ʳ At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ Optical characteristics shall be satisfied.ʳ At the end of the test, electric, mechanical, and optical specifications shall be satisfied.ʳ Drop from height of 122 cm At the end of the test, electric, on concrete surface. full packed for mechanical, and optical Drop sequence: 1 corner, 3 shipment specifications shall be satisfied.ʳ edges, 6 faces One drop for each. 12 Package Drop Impact 13 Electrostatic Effect (non-operating) Machine model 㪂㪆㪄㩷250V, 0Ө, 200pF 14 Altitude test Operation 700hPa ( = 3000m ) 48Hr IEC 62179, IEC 62180 At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ ʳ At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ ʳ The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:17 P-511-523(V:1) ED060SC4 15 16 Altitude test Storage 260hPa ( = 10000m ) 48Hr Stylus Tapping POLYACETAL Pen: Top R0.4mm Load: 300gf Speed: 5times/sec Total 13,500times, ʳ At the end of the test, electric, mechanical, specifications shall be satisfied.ʳ ʳ Pass criteria – no glass breakage or damage to microcapsules. Actual EMC level to be measured on customer application The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:18 P-511-523(V:1) ED060SC4 11.Block Diagram ˟˖˗ʳˣ˴́˸˿ ˩ʳ˗̅˼̉˸̅ ʻ˚˴̇˸ʼ ˛ʳ˗̅˼̉˸̅ ʻ˦̂̈̅˶˸ʼ 39 PIN Input The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:19 P-511-523(V:1) ED060SC4 12.Packing The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:20