AD ADCMP573 Ultrafast 3.3 v/5 v single-supply sige comparator Datasheet

Ultrafast 3.3 V/5 V
Single-Supply SiGe Comparators
ADCMP572/ADCMP573
3.3 V/5.2 V single-supply operation
150 ps propagation delay
15 ps overdrive and slew rate dispersion
8 GHz equivalent input rise time bandwidth
80 ps minimum pulse width
35 ps typical output rise/fall
10 ps deterministic jitter (DJ)
200 fs random jitter (RJ)
On-chip terminations at both input pins
Robust inputs with no output phase reversal
Resistor-programmable hysteresis
Differential latch control
Extended industrial −40°C to +125°C temperature range
FUNCTIONAL BLOCK DIAGRAM
VCCI
VCCO
VTP TERMINATION
VP NONINVERTING
INPUT
VN INVERTING
INPUT
Q OUTPUT
ADCMP572
ADCMP573
CML/
RSPECL
Q OUTPUT
VTN TERMINATION
LE INPUT
HYS
LE INPUT
04409-025
FEATURES
Figure 1.
APPLICATIONS
Clock and data signal restoration and level shifting
Automatic test equipment (ATE)
High speed instrumentation
Pulse spectroscopy
Medical imaging and diagnostics
High speed line receivers
Threshold detection
Peak and zero-crossing detectors
High speed trigger circuitry
GENERAL DESCRIPTION
The ADCMP572 and ADCMP573 are ultrafast comparators
fabricated on Analog Devices’ proprietary XFCB3 Silicon
Germanium (SiGe) bipolar process. The ADCMP572 features
CML output drivers and latch inputs, and the ADCMP573
features reduced swing PECL (RSPECL) output drivers and
latch inputs.
Both devices offer 150 ps propagation delay and 80 ps
minimum pulse width for 10 Gbps operation with 200 fs rms
random jitter (RJ). Overdrive and slew rate dispersion are
typically less than 15 ps.
A flexible power supply scheme allows both devices to operate
with a single 3.3 V positive supply and a −0.2 V to +1.2 V input
signal range or with split input/output supplies to support a
wider −0.2 V to +3.2 V input signal range and an independent
range of output levels. 50 Ω on-chip termination resistors are
provided at both inputs with the optional capability to be left
open (on an individual pin basis) for applications requiring
high impedance inputs.
The CML output stage is designed to directly drive 400 mV into
50 Ω transmission lines terminated to between 3.3 V to 5.2 V.
The RSPECL output stage is designed to drive 400 mV into
50 Ω terminated to VCCO − 2 V and is compatible with several
commonly used PECL logic families. The comparator input
stage offers robust protection against large input overdrive, and
the outputs do not phase reverse when the valid input signal
range is exceeded. High speed latch and programmable
hysteresis features are also provided.
The ADCMP572 and ADCMP573 are available in a 16-lead
LFCSP package and have been characterized over an extended
industrial temperature range of −40°C to +125°C.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2005 Analog Devices, Inc. All rights reserved.
ADCMP572/ADCMP573
TABLE OF CONTENTS
Electrical Characteristics ................................................................. 3
Using/Disabling the Latch Feature..............................................9
Absolute Maximum Ratings............................................................ 5
Optimizing High Speed Performance ..................................... 10
Thermal Considerations.............................................................. 5
Comparator Propagation Delay Dispersion ........................... 10
ESD Caution.................................................................................. 5
Comparator Hysteresis .............................................................. 11
Pin Configuration and Function Descriptions............................. 6
Minimum Input Slew Rate Requirements .............................. 11
Typical Performance Characteristics ............................................. 7
Typical Application Circuits.......................................................... 12
Application Information.................................................................. 9
Timing Information ....................................................................... 13
Power/Ground Layout and Bypassing ....................................... 9
Outline Dimensions ....................................................................... 14
CML/RSPECL Output Stage ....................................................... 9
Ordering Guide .......................................................................... 14
REVISION HISTORY
4/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADCMP572/ADCMP573
ELECTRICAL CHARACTERISTICS
VCCI = VCCO = 3.3 V, TA = −40°C to +125°C, typical at TA = +25°C, unless otherwise noted.
Table 1.
Parameter
DC INPUT CHARACTERISTICS
Input Voltage Range
Input Differential Voltage
Input Offset Voltage
Offset Voltage Tempco
Input Bias Current
Input Bias Current Tempco
Input Offset Current
Input Impedance
Input Resistance, Differential
Input Resistance, Common-Mode
Active Gain
Common-Mode Rejection
Power Supply Rejection—VCCI
Hysteresis
LATCH ENABLE CHARACTERISTICS
ADCMP572
Latch Enable Input Range
Latch Enable Input Differential
Latch Setup Time
Latch Hold Time
ADCMP573
Latch Enable Input Range
Latch Enable Input Differential
Latch Setup Time
Latch Hold Time
Latch Enable Input Impedance
Latch to Output Delay
Latch Minimum Pulse Width
DC OUTPUT CHARACTERISTICS
ADCMP572 (CML)
Output Impedance
Output Voltage High Level
Output Voltage Low Level
Output Voltage Differential
ADCMP573 (RSPECL)
Output Voltage High −40°C
Output Voltage High +25°C
Output Voltage High +125°C
Output Voltage Low −40°C
Output Voltage Low +25°C
Output Voltage Low +125°C
Output Voltage Differential
Symbol
Conditions
Min
VP, VN
VCCI = 3.3 V, VCCO = 3.3 V
VCCI = 5.2 V, VCCO = 3.3 V
−0.2
−0.2
−1.2
−5.0
VOS
∆VOS/dT
IP, IN
Open termination
−50.0
Open termination
Open termination
AV
CMRR
PSRVCCI
VCCI = 3.3 V, VCCO = 3.3 V,
VCM = 0.0 V to 1.0 V
VCCI = 5.2 V, VCCO = 3.3 V,
VCM = 0.0 V to 3.0 V
VCCI = 3.3 V ± 5%, VCCO = 3.3 V
RHYS = ∞
2.8
0.2
tS
tH
VOD = 100 mV
VOD = 100 mV
1.8
0.2
Typ
±2.0
10.0
−25.0
50.0
±2.0
50
50
500
54
65
Max
Unit
+1.2
+3.1
+1.2
+5.0
V
V
V
mV
µV/°C
µA
nA/°C
µA
Ω
kΩ
kΩ
dB
dB
0.0
65
dB
74
±1
dB
mV
0.4
15
5
0.4
90
100
50.0
150
100
VCCO + 0.2
0.5
V
V
ps
ps
VCCO − 0.6
0.5
V
V
ps
ps
Ω
ps
ps
tS
tH
VOD = 100 mV
VOD = 100 mV
tPLOH, tPLOL
tPL
VOD = 100 mV
VOD = 100 mV
ZOUT
VOH
VOL
−8 mA < IOUT < 8 mA
50 Ω terminate to VCCO
50 Ω terminate to VCCO
50 Ω terminate to VCCO
VCCO − 0.10
VCCO − 0.60
300
50.0
VCCO − 0.05
VCCO − 0.45
375
VCCO
VCCO − 0.30
450
Ω
V
V
mV
VOH
VOH
VOH
VOL
VOL
VOL
50 Ω terminate to VCCO − 2.0
50 Ω terminate to VCCO − 2.0
50 Ω terminate to VCCO − 2.0
50 Ω terminate to VCCO − 2.0
50 Ω terminate to VCCO − 2.0
50 Ω terminate to VCCO − 2.0
50 Ω terminate to VCCO − 2.0
VCCO − 1.14
VCCO − 1.10
VCCO − 1.04
VCCO − 1.54
VCCO − 1.50
VCCO − 1.44
300
VCCO − 1.02
VCCO − 0.98
VCCO − 0.92
VCCO − 1.39
VCCO − 1.35
VCCO − 1.29
375
VCCO − 0.90
VCCO − 0.86
VCCO − 0.80
VCCO − 1.24
VCCO − 1.20
VCCO − 1.14
450
V
V
V
V
V
V
mV
Rev. 0 | Page 3 of 16
ADCMP572/ADCMP573
Parameter
AC PERFORMANCE
Propagation Delay
Propagation Delay Tempco
Prop Delay Skew—Rising Transition
to Falling Transition
Overdrive Dispersion
Symbol
Conditions
tPD
VCCI = 3.3 V, VOD = 200 mV
VCCI = 3.3 V, VOD = 20 mV
VCCI = 5.2 V, VOD = 200 mV
∆tPD/dT
VOD = 200 mV, 5 V/ns
Slew Rate Dispersion
Pulse Width Dispersion
10% – 90% Duty Cycle Dispersion
Common-Mode Dispersion
Equivalent Input Bandwidth1
Toggle Rate
Deterministic Jitter
RMS Random Jitter
Minimum Pulse Width
Rise Time
Fall Time
POWER SUPPLY
Input Supply Voltage Range
Output Supply Voltage Range
Positive Supply Differential
ADCMP572 (CML)
Positive Supply Current
Device Power Dissipation
ADCMP573 (RSPECL)
Positive Supply Current
Device Power Dissipation
1
Min
BWEQ
DJ
RJ
PWMIN
PWMIN
tR
tF
50 mV < VOD < 0.2 V, 5 V/ns
10 mV < VOD < 0.2 V, 5 V/ns
2 V/ns to 10 V/ns, 250 mV OD
100 ps to 5 ns, 250 mV OD
VCCI = 3.3 V, 1 V/ns, 250 mV OD
VCCI = 5.2 V, 1 V/ns, 250 mV OD
VOD = 0.2V, 0.0 V < VCM < 2.9 V
0.0 V to 250 mV input
tR = tF = 17 ps, 20/80
>50% Output Swing
VOD = 200 mV, 5 V/ns,
PRBS31 − 1 NRZ, 4 Gbps
VOD = 200 mV, 5 V/ns,
PRBS31 − 1 NRZ, 10 Gbps
VOD = 200 mV, 5 V/ns, 1.25 GHz
∆tPD/∆PW < 5 ps, 200 mV OD
∆tPD/∆PW < 10 ps, 200 mV OD
20/80
20/80
VCCI
VCCO
VCCI −VCCO
IVCCI + IVCCO
PD
IVCCI + IVCCO
PD
Typ
Max
Unit
150
165
145
0.5
10
ps
ps
ps
ps/°C
ps
15
15
15
5
5
10
5
8.0
ps
ps
ps
ps
ps
ps/V
GHz
12.5
10
Gbps
ps
20
ps
0.2
100
80
35
35
ps
ps
ps
ps
ps
3.1
3.1
−0.2
5.4
5.4
+2.3
V
V
V
mA
VCCI = 3.3 V, VCCO = 3.3 V,
terminate 50 Ω to VCCO
VCCI = 5.2 V, VCCO = 5.2 V,
terminate 50 Ω to VCCO
VCCI = 3.3 V, VCCO = 3.3 V,
terminate 50 Ω to VCCO
VCCI = 5.2 V, VCCO = 5.2 V,
terminate 50 Ω to VCCO
44
52
44
52
140
165
230
265
VCCI = 3.3 V, VCCO = 3.3 V,
50 Ω to VCCO − 2 V
VCCI = 5.2 V, VCCO = 5.2 V,
50 Ω to VCCO − 2V
VCCI = 3.3 V, VCCO = 3.3 V,
50 Ω to VCCO − 2 V
VCCI = 5.2 V, VCCO = 5.2 V,
50 Ω to VCCO − 2 V
62
80
64
80
110
160
146
230
mW
mA
mW
Equivalent input bandwidth assumes a simple first-order response and is calculated with the following formula: BWEQ = 0.22/√(trCOMP2−trIN2), where trIN is the 20/80
transition time of a quasi-Gaussian signal applied to the comparator input, and trCOMP is the effective transition time digitized by the comparator.
Rev. 0 | Page 4 of 16
ADCMP572/ADCMP573
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
SUPPLY VOLTAGE
Input Supply Voltage
(VCCI to GND)
Output Supply Voltage
(VCCO to GND)
Positive Supply Differential
(VCCI − VCCO)
INPUT VOLTAGE
Input Voltage
Differential Input Voltage
Input Voltage, Latch Enable
HYSTERESIS CONTROL PIN
Applied Voltage (HYS to GND)
Maximum Input/Output Current
OUTPUT CURRENT
ADCMP572 (CML)
ADCMP573 (RSPECL)
TEMPERATURE
Operating Temperature, Ambient
Operating Temperature, Junction
Storage Temperature Range
Stress above those listed under Absolute Maximum Ratings may
cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other
conditions above those indicated in the operational section of
this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device
reliability.
Rating
−0.5 V to +6.0 V
−0.5 V to +6.0 V
−0.5 V to +3.5 V
−0.5 V to VCCI + 0.5 V
±(VCCI + 0.5 V)
−0.5 V to VCCO + 0.5 V
THERMAL CONSIDERATIONS
The ADCMP572/ADCMP573 LFCSP 16-lead package has a θJA
(junction-to-ambient thermal resistance) of 70°C/W in still air.
−0.5 V to +1.5 V
±1 mA
±20 mA
−35 mA
−40°C to +125°C
+150°C
−65°C to +150°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 16
ADCMP572/ADCMP573
GND
GND
16
HYS
VCCI
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
15
14
13
PIN1
VTP 1
12 VCCO
ADCMP572
ADCMP573
VP 2
VN 3
11 Q
10 Q
TOP VIEW
(Not to Scale)
VTN 4
8
VCCO/VTT
04409-026
7
LE
VCCI
6
LE
9 VCCO
5
Figure 2. ADCMP572/ADCMP573 Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
2
3
4
5, 16
6
Mnemonic
VTP
VP
VN
VTN
VCCI
LE
7
LE
8
VCCO/VTT
9, 12
13, 15
10
VCCO
GND
Q
11
Q
14
HYS
Isolated
Heat sink
N/C
Description
Termination Resistor Return Pin for VP Input.
Noninverting Analog Input.
Inverting Analog Input.
Termination Resistor Return Pin for VN Input.
Positive Supply Voltage for Input Stage.
Latch Enable Input Pin, Inverting Side.
In compare mode (LE = low), the output tracks changes at the input of the comparator.
In latch mode (LE = high), the output reflects the input state just prior to the comparator’s being
placed into latch mode. LE must be driven in complement with LE.
Latch Enable Input Pin, Noninverting Side.
In compare mode (LE = high), the output tracks changes at the input of the comparator.
In latch mode (LE = low), the output reflects the input state just prior to the comparator’s being
placed into latch mode. LE must be driven in compliment with LE.
Termination Return Pin for the LE/LE Input Pins.
For the ADCMP572 (CML output stage), this pin is internally connected to and also should be
externally connected to the positive VCCO supply.
For the ADCMP573 (RSPECL output stage), this pin should normally be connected to the VCCO – 2 V
termination potential.
Positive Supply Voltage for the CML/RSPECL Output Stage.
Ground.
Inverting Output. Q is at logic low if the analog voltage at the noninverting input, VP, is greater than
the analog voltage at the inverting input, VN, provided the comparator is in compare mode. See the
LE/LE descriptions (Pins 6 and 7) for more information.
Noninverting Output. Q is at logic high if the analog voltage at the noninverting input VP is greater
than the analog voltage at the inverting input, VN, provided the comparator is in compare mode. See
the LE/LE descriptions (Pins 6 and 7) for more information.
Hysteresis Control Pin. Leave this pin disconnected for zero hysteresis. Connect to GND with a
suitably sized resistor to add the desired amount of hysteresis. Refer to Figure 7 for proper sizing of
RHYS hysteresis control resistor.
The metallic back surface of the package is not electrically connected to any part of the circuit, and it
can be left floating for best electrical isolation between the package handle and the substrate of the
die. However, it can be soldered to the application board if improved thermal and/or mechanical
stability is desired.
Rev. 0 | Page 6 of 16
ADCMP572/ADCMP573
TYPICAL PERFORMANCE CHARACTERISTICS
VCCI = VCCO = 3.3 V, TA = 25°C, unless otherwise noted.
39.0
38.5
RISE/FALL TIME (ps)
15
10
38.0
37.5
37.0
5
0
0
50
100
150
200
250
INPUT OVERDRIVE VOLTAGE (mV)
36.0
–60
0
20
40
60
80
100
Figure 6. Rise/Fall Time vs. Temperature
158.5
60
158.0
50
157.5
HYSTERESIS (mV)
157.0
156.5
40
30
20
156.0
10
0.2
0.4
0.6
0.8
1.0
1.2
INPUT COMMON-MODE VOLTAGE (V)
0
0
1
2
3
4
5
04409-043
0
04409-040
155.5
6
RHYS (kΩ)
Figure 4. Propagation Delay vs. Input Common-Mode
Figure 7. Hysteresis vs. RHYS Control Resistor
160
80
70
156
60
HYSTERESIS (mV)
158
154
152
150
50
40
30
20
148
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
100
04409-041
10
146
–60
Figure 5. Propagation Delay vs. Temperature
0
–600
04409-047
PROPAGATION DELAY (ps)
–20
TEMPERATURE (°C)
Figure 3. Propagation Delay vs. Input Overdrive
PROPAGATION DELAY (ps)
–40
04409-042
36.5
04409-039
PROPAGATION DELAY ERROR (ps)
20
–500
–400
–300
–200
RHYS SINK CURRENT (µA)
Figure 8. Hysteresis vs. RHYS Sink Current
Rev. 0 | Page 7 of 16
–100
0
–15.0
380
–15.5
379
–16.0
378
OUTPUT LEVELS (mV)
–16.5
–17.0
–17.5
377
376
375
374
–18.5
–0.5
–0.3
–0.1
0.1
0.3
0.5
0.7
0.9
1.1
1.3
04409-044
–18.0
1.5
VP INPUT VOLTAGE (VN = –0.2V)
373
–60
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 12. Output Levels vs. Temperature
Figure 9. Input Bias Current vs. Input Differential
–16.2
496.0mV
–16.4
–16.5
–16.6
–16.7
–16.8
–20
0
20
40
60
80
100
TEMPERATURE (°C)
504.0mV
60.00ps/DIV
04409-049
–40
04409-045
M1
–16.9
–60
Figure 13. ADCMP572 Eye Diagram at 2.5 Gbps
Figure 10. Input Bias Current vs. Temperature
0.5
500.0mV
0.4
0.3
0.2
0.1
0
–0.1
–0.2
–0.4
–0.5
–50
–25
0
25
50
TEMPERATURE (°C)
75
100
500.0mV
125
25.00ps/DIV
Figure 14. ADCMP572 Eye Diagram at 6.5 Gbps
Figure 11. Input Offset Voltage vs. Temperature
Rev. 0 | Page 8 of 16
04409-050
–0.3
04409-024
OFFSET (mV)
INPUT BIAS CURRENT (µA)
–16.3
04409-046
INPUT BIAS CURRENT (µA)
ADCMP572/ADCMP573
ADCMP572/ADCMP573
APPLICATION INFORMATION
POWER/GROUND LAYOUT AND BYPASSING
The ADCMP572/ADCMP573 comparators are very high speed
SiGe devices. Consequently, it is essential to use proper high
speed design techniques to achieve the specified performance.
Of critical importance is the use of low impedance supply
planes, particularly the output supply plane (VCCO) and the
ground plane (GND). Individual supply planes are recommended as part of a multilayer board. Providing the lowest
inductance return path for switching currents ensures the best
possible performance in the target application.
strip line techniques are essential to ensure proper transition
times and to prevent output ringing and pulse width dependent
propagation delay dispersion. For the most timing critical
applications where transmission line reflections pose the
greatest risk to performance, the ADCMP572 provides the best
match to 50 Ω output transmission paths.
VCCO
50Ω
Q
It is important to adequately bypass the input and output
supplies. A 1 µF electrolytic bypass capacitor should be placed
within several inches of each power supply pin to ground. In
addition, multiple high quality 0.01 µF bypass capacitors should
be placed as close as possible to each of the VCCI and VCCO
supply pins and should be connected to the GND plane with
redundant vias. High frequency bypass capacitors should be
carefully selected for minimum inductance and ESR. Parasitic
layout inductance should be avoided to maximize the
effectiveness of the bypass at high frequencies.
Q
GND
04409-037
16mA
Figure 15. Simplified Schematic Diagram of
the ADCMP572 CML Output Stage
If the input and output supplies are connected separately such
that VCCI ≠ VCCO, care should be taken to bypass each of these
supplies separately to the GND plane. A bypass capacitor should
not be connected between them. It is recommended that the
GND plane separate the VCCI and VCCO planes when the circuit
board layout is designed to minimize coupling between the two
supplies and to take advantage of the additional bypass capacitance from each respective supply to the ground plane. This
enhances the performance when split input/output supplies are
used. If the input and output supplies are connected together for
single-supply operation such that VCCI = VCCO, coupling between
the two supplies is unavoidable; however, every effort should be
made to keep the supply plane adjacent to the GND plane to
maximize the additional bypass capacitance this arrangement
provides.
VCCO
Q
GND
04409-038
Q
Figure 16. Simplified Schematic Diagram of
the ADCMP573 RSPECL Output Stage
CML/RSPECL OUTPUT STAGE
USING/DISABLING THE LATCH FEATURE
Specified propagation delay dispersion performance can be
achieved only by using proper transmission line terminations.
The outputs of the ADCMP572 are designed to directly drive
400 mV into 50 Ω cable, microstrip, or strip line transmission
lines properly terminated to the VCCO supply plane. The CML
output stage is shown in the simplified schematic diagram of
Figure 15. The outputs are each back terminated with 50 Ω for
best transmission line matching. The RSPECL outputs of the
ADCMP573 are illustrated in Figure 16 and should be
terminated to VCCO − 2 V. As an alternative, Thevenin equivalent
termination networks can be used in either case if the direct
termination voltage is not readily available. If high speed output
signals must be routed more than a centimeter, microstrip or
The latch inputs (LE/LE) are active low for latch mode and are
internally terminated with 50 Ω resistors to Pin 8. This pin
corresponds to and is internally connected to the VCCO supply
for the CML-compatible ADCMP572. With the aid of these
resistors the ADCMP572 latch function can be disabled by
connecting the LE pin to GND with an external pull-down
resistor and leaving the LE pin unconnected. To avoid excessive
power dissipation, the resistor should be 750 Ω when VCCO =
3.3 V, and 1.2 kΩ when VCCO = 5.2 V. In the PECL-compatible
ADCMP573, the VTT pin should be connected externally to the
PECL termination supply at VCCO – 2 V. The latch can then be
disabled by connecting the LE pin to VCCO with an external
Rev. 0 | Page 9 of 16
ADCMP572/ADCMP573
500 Ω resistor and leaving the LE pin disconnected. In this case,
the resistor value does not depend on the VCCO supply voltage.
COMPARATOR PROPAGATION
DELAY DISPERSION
VCCO is the signal return for the output stage and VCCO pins
should of course be connected to a supply plane for maximum
performance.
The ADCMP572/ADCMP573 comparators are designed to
reduce propagation delay dispersion over a wide input overdrive
range of 5 mV to 500 mV. Propagation delay dispersion is
variation in the propagation delay that results from a change in
the degree of overdrive or slew rate (how far or how fast the
input signal exceeds the switching threshold).
For applications working in a 50 Ω environment, input and
output matching has a significant impact on data dependent (or
deterministic) jitter (DJ) and on pulse width dispersion
performance. The ADCMP572/ADCMP573 comparators
provide internal 50 Ω termination resistors for both the VP and
VN inputs, and the ADCMP572 provides 50 Ω back terminated
outputs. The return side for each input termination is pinned
out separately with the VTP and VTN pins, respectively. If a 50 Ω
termination is desired at one or both of the VP/VN inputs, then
the VTP and VTN pins can be connected (or disconnected) to
(from) the desired termination potential as required. The
termination potential should be carefully bypassed using high
quality bypass capacitors as discussed earlier to prevent
undesired aberrations on the input signal due to parasitic
inductance in the circuit board layout. If a 50 Ω input
termination is not desired, either one or both of the VTP/VTN
termination pins can be left disconnected. In this case, the pins
should be left floating with no external pull-downs or bypassing
capacitors.
Propagation delay dispersion is a specification that becomes
important in high speed, time-critical applications such as data
communication, automatic test and measurement, instrumentation, and event driven applications such as pulse spectroscopy,
nuclear instrumentation, and medical imaging. Dispersion is
defined as the variation in propagation delay as the input overdrive conditions vary (Figure 17 and Figure 18). For the
ADCMP572/ADCMP573, dispersion is typically <15 ps because
the overdrive varies from 10 mV to 500 mV, and the input slew
rate varies from 2 V/ns to 10 V/ns. This specification applies for
both positive and negative signals since the ADCMP572/
ADCMP573 has substantially equal delays for either positive
going or negative going inputs.
When leaving an input termination disconnected, the internal
resistor acts as a small stub on the input transmission path and
can cause problems for very high speed inputs. Reflections
should then be expected from the comparator inputs because
they no longer provide matched impedance to the input path
leading to the device. In this case, it is important to back match
the drive source impedance to the input transmission path to
minimize multiple reflections. For applications in which the
comparator is very close to the driving signal source, the source
impedance should be minimized. High source impedance in
combination with parasitic input capacitance of the comparator
might cause an undesirable degradation in bandwidth at the
input, therefore degrading the overall response. Although the
ADCMP572/ ADCMP573 comparators have been designed to
minimize input capacitance, some parasitic capacitance is
inevitable. It is therefore recommended that the drive source
impedance be no more than 50 Ω for best high speed
performance.
Rev. 0 | Page 10 of 16
500mV OVERDRIVE
INPUT VOLTAGE
10mV OVERDRIVE
VN ± VOS
DISPERSION
Q/Q OUTPUT
04409-0-027
As with any high speed comparator, proper design and layout
techniques are essential to obtaining the specified performance.
Stray capacitance, inductance, inductive power and ground
impedances, or other layout issues can severely limit
performance and often cause oscillation. Discontinuities along
input and output transmission lines can severely limit the
specified pulse width dispersion performance.
Figure 17. Propagation Delay—Overdrive Dispersion
INPUT VOLTAGE
1V/ns
VN ± VOS
10V/ns
DISPERSION
Q/Q OUTPUT
04409-0-028
OPTIMIZING HIGH SPEED PERFORMANCE
Figure 18. Propagation Delay—Slew Rate Dispersion
ADCMP572/ADCMP573
The addition of hysteresis to a comparator is often desirable in a
noisy environment or when the differential input amplitudes are
relatively small or slow moving, but excessive hysteresis has a
cost in degraded accuracy and slew-induced timing shifts. The
transfer function for a comparator with hysteresis is shown in
Figure 19. If the input voltage approaches the threshold (0.0 V
in this example) from the negative direction, the comparator
switches from low to high when the input crosses +VH/2. The
new switching threshold becomes −VH/2. The comparator
remains in the high state until the threshold −VH/2 is crossed
from the positive direction. In this manner, noise centered on
0.0 V input does not cause the comparator to switch states
unless it exceeds the region bounded by ±VH/2.
OUTPUT
applied as a function of external resistor value. The advantages
of applying hysteresis in this manner are improved accuracy,
stability, and reduced component count. An external bypass
capacitor is not recommended on the HYS pin because it would
likely degrade the jitter performance of the device. The
hysteresis pin could also be driven by a CMOS DAC. It is biased
to approximately 250 mV and has an internal series resistance
of 600 Ω.
60
50
HYSTERESIS (mV)
COMPARATOR HYSTERESIS
VOH
40
30
20
0
0
1
2
3
4
5
6
RHYS (kΩ)
VOL
04409-043
10
Figure 20. Hysteresis vs. RHYS Control Resistor
0
+VH
2
INPUT
MINIMUM INPUT SLEW RATE REQUIREMENTS
04409-005
–VH
2
Figure 19. Comparator Hysteresis Transfer Function
The customary technique for introducing hysteresis into a
comparator uses positive feedback from the output back to the
input. A limitation of this approach is that the amount of
hysteresis varies with the output logic levels, resulting in
hysteresis that can be load dependent and is not symmetrical
about the threshold. The external feedback network can also
introduce significant parasitics, which reduce high speed
performance and can even induce oscillation in some cases.
The ADCMP572/ADCMP573 comparators offer a programmable hysteresis feature that can significantly improve the
accuracy and stability of the desired hysteresis. By connecting
an external pull-down resistor from the HYS pin to GND, a
variable amount of hysteresis can be applied. Leaving the HYS
pin disconnected disables the feature, and hysteresis is then less
than 1 mV as specified. The maximum hysteresis that can be
applied using this method is approximately ±25 mV with the
pin grounded. Figure 20 illustrates the amount of hysteresis
As with all high speed comparators, a minimum slew rate
requirement must be met to ensure that the device does not
oscillate as the input signal crosses the threshold. This
oscillation is due in part to the high input bandwidth of the
comparator and the feedback parasitics inherent in the package.
A minimum slew rate of 50 V/µs should ensure clean output
transitions from the ADCMP572/ ADCMP573 comparators.
The slew rate may be too slow for other reasons. The extremely
high bandwidth of these devices means that broadband noise
can be a significant factor when input slew rates are low. There
will be at least 120 µv of thermal noise generated over the full
comparator bandwidth by two 50 Ω terminations at room
temperature. With a slew rate of only 50 V/µs the input will be
inside this noise band for over 2 ps, rendering the comparator’s
jitter performance of 200 fs moot. Raising the slew rate of the
input signal and/or reducing the bandwidth over which this
resistance is seen at the input can greatly reduce jitter.
Rev. 0 | Page 11 of 16
ADCMP572/ADCMP573
TYPICAL APPLICATION CIRCUITS
3.3V
VCCI
VCCO
VCCI
50Ω
VTP
VCCO = 3.3V
50Ω
5V
75Ω
VP
VIN
VN
Q
ADCMP572
100Ω
ADCMP572
Q
VTN
100Ω
50Ω
Figure 25. Interfacing 3.3 V CML to a 50 Ω
Ground Terminated Instrument
Figure 21. Zero-Crossing Detector with 3.3 V CML Outputs
VCCI = 5.2V
VCCI
VCCO = 3.3V
VCCO
VTP
50Ω
VN
VN
50Ω
Q
VP
ADCMP572
VN
Q
VCCO
750Ω
04409-035
04409-030
LATCH
INPUTS
Figure 26. Disabling the ADCMP572 Latch Feature
Figure 22. LVDS to 50 Ω Back Terminated RSPECL Receiver
VCCI = 3.3V
VCCO = 2.5V/3.3V
VCCI = 5.2V = VCCO
2.5V/3.3V
50Ω
VIN
VTH
–
50Ω
Q
VP
ADCMP572
VN
Q
ADCMP573
VTT = 3.2V
VCCO
Figure 27. Disabling the ADCMP573 Latch Feature
Figure 23. Comparator with ±1 V Input Range and
2.5 V or 3.3 V CML Outputs
VCCI = 5.2V
VCCO = 3.3V/5.2V
VCCI
3.3V/5.2V
50Ω
VCCO
VCCO
50Ω
50Ω
50Ω
Q
ADCMP572
ADCMP572
Q
0Ω TO 5kΩ
04409-036
LATCH
INPUTS
HYS
04409-032
VTH
50Ω
04409-048
GND = –1V
50Ω
500Ω
04409-031
LATCH
INPUTS
VIN
50Ω
ADCMP572
VTN
+
VCCO
50Ω
VP
VP
04409-034
04409-029
LATCH
INPUTS
50Ω
LATCH
INPUTS
Figure 28. Adding Hysteresis Using the HYS Control Pin
Figure 24. Comparator with 0 V to 3 V Input Range and
3.3 V or 5.2 V Positive CML Outputs
Rev. 0 | Page 12 of 16
ADCMP572/ADCMP573
TIMING INFORMATION
Figure 29 illustrates the ADCMP572/ADCMP573 compare and latch timing relationships. Table 4 provides definitions of the terms
shown in the figure.
LATCH ENABLE
50%
LATCH ENABLE
tS
tPL
tH
DIFFERENTIAL
INPUT VOLTAGE
VIN
VN ± VOS
VOD
tPDL
tPLOH
Q OUTPUT
50%
tF
tPDH
tPLOL
tR
04409-003
50%
Q OUTPUT
Figure 29. System Timing Diagram
Table 4. Timing Descriptions
Symbol
tPDH
Timing
Input to output high delay
tPDL
Input to output low delay
tPLOH
Latch enable to output high delay
tPLOL
Latch enable to output low delay
tH
Minimum hold time
tPL
Minimum latch enable pulse width
tS
Minimum setup time
tR
Output rise time
tF
Output fall time
VOD
Voltage overdrive
Description
Propagation delay measured from the time the input signal crosses the reference (± the
input offset voltage) to the 50% point of an output low-to-high transition.
Propagation delay measured from the time the input signal crosses the reference (± the
input offset voltage) to the 50% point of an output high-to-low transition.
Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output low-to-high transition.
Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output high-to-low transition.
Minimum time after the negative transition of the latch enable signal that the input signal
must remain unchanged to be acquired and held at the outputs.
Minimum time that the latch enable signal must be high to acquire an input signal
change.
Minimum time before the negative transition of the latch enable signal that an input
signal change must be present to be acquired and held at the outputs.
Amount of time required to transition from a low to a high output as measured at the
20% and 80% points.
Amount of time required to transition from a high to a low output as measured at the
20% and 80% points.
Difference between the input voltages VA and VB.
Rev. 0 | Page 13 of 16
ADCMP572/ADCMP573
OUTLINE DIMENSIONS
3.00
BSC SQ
0.60 MAX
13
12
0.45
PIN 1
INDICATOR
TOP
VIEW
2.75
BSC SQ
0.80 MAX
0.65 TYP
1.00
0.85
0.80
SEATING
PLANE
PIN 1 INDICATOR
16
1
1.65
1.50 SQ*
1.35
EXPOSED
PAD
0.50
BSC
12° MAX
0.50
0.40
0.30
9 (BOTTOM VIEW) 4
8
5
0.25 MIN
1.50 REF
0.05 MAX
0.02 NOM
0.30
0.23
0.18
0.20 REF
*COMPLIANT TO JEDEC STANDARDS MO-220-VEED-2
EXCEPT FOR EXPOSED PAD DIMENSION
Figure 30. 16-Lead Lead Frame Chip Scale Package [LFCSP]
3 x 3 mm Body
(CP-16-3)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADCMP572BCP-WP
ADCMP572BCP-R2
ADCMP572BCP-RL7
EVAL-ADCMP572BCP
ADCMP573BCP-WP
ADCMP573BCP-R2
ADCMP573BCP-RL7
EVAL-ADCMP573BCP
Temperature Range
−40°C to 85°C
−40°C to 85°C
−40°C to 85°C
−40°C to 85°C
−40°C to 85°C
−40°C to 85°C
Package Description
LFCSP-16
LFCSP-16
LFCSP-16
Evaluation Board
LFCSP-16
LFCSP-16
LFCSP-16
Evaluation Board
Rev. 0 | Page 14 of 16
Package Option
CP-16-3
CP-16-3
CP-16-3
CP-16-3
CP-16-3
CP-16-3
ADCMP572/ADCMP573
NOTES
Rev. 0 | Page 15 of 16
ADCMP572/ADCMP573
NOTES
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04409–0–4/05(0)
Rev. 0 | Page 16 of 16