ETC2 BT-210 Bluetooth usb adapter Datasheet

Amp’ed RF, Inc.
(phone) 408 213-9530
(fax) 408 213-9533
Product Specification
Features
Description
The BT-210 Bluetooth USB Adapter is a perfect solution for those looking
for easy, all-in-one, Bluetooth connectivity.
Our design eliminates the need for a system to apply its processing and
memory resources to running the BT-210 since it already has its own
microprocessor, memory, and firmware!
Customized firmware for peripheral device interaction, power optimization,
security, and other proprietary features may be supported and can be
ordered pre-loaded and configured.
Additional Documentation
„
„
„
„
„
„
„
„
„
-
Bluetooth Radio
Fully embedded Bluetooth v2.0 Serial Profile
Class 2 radio
Built with our BT-21 bluetooth module
Wireless data communications
Integrated chip antenna
128-bit encryption security
Range up to 30m LOS
FCC & Bluetooth qualified
ST Micro ARM7 microprocessor up to 50MHz
Memory
256K bytes flash memory
64K bytes RAM memory
Data Rate
2M bps maximum data rate
Multipoint capability
Serial Interface
COM port, up to 480K baud
USB v2.0
User Interface
AT command set (abSerial)
abSerial User Guide
abSerial Reference Guide
BT-21 Datasheet
©2008
Amp’ed RF Inc
1
9/30/08
1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA
www.ampedrf.com
BT-210 Datasheet
Page 1 of 7
Amp’ed RF, Inc.
(phone) 408 213-9530
(fax) 408 213-9533
Software Architecture
Upper Layer Stack
Lower Layer Stack
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Full Bluetooth v2.0 data rate (3M bps maximum)
Device power modes—active, sleep and deep sleep
Wake on Bluetooth feature—optimized power consumption of host CPU
Authentication and encryption
Encryption key length from 8-bits to 128-bits maximum
Persistent FLASH memory—for BD Address and radio parameter
storage
All ACL (Asynchronous Connection Less) packet types (DM1, DH1, DM3,
DH3, DM5, DH5, 2-DH1, 2-DH3, 2-DH5, 3-DH1 3-DH3, 3-DH5, AUX1)
SCO (Synchronous Connection Oriented) packet types (HV1, HV2, HV3)
Point to multipoint and scatternet support—3 master and 7 slave links
allowed (10 active links simultaneously)
Park, sniff, and hold modes—fully supported to maximum allowed
intervals
Master slave switch—supported during connection and post connection
Dedicated Inquiry Access Code—for improved inquiry scan performance
Dynamic packet selection—channel quality driven data rate to optimize
link performance
Dynamic power control—interference reduction and link performance
Bluetooth test modes—per Bluetooth v2.0 specification
802.11b co-existence—AWMA and AFH
Vendor specific HCI commands—to support device configuration and
certification test modes
ƒ
ƒ
SPP, OBEX, SDAP, GAP, and DUN protocols
RFComm, SDP, and L2CAP supported
HCI Interface
ƒ
ƒ
ƒ
Bluetooth v2.0 specification compliant
HCI UART transport layer (H4)
Firmware upgrade over UART
APPLICATIONS
UPPER LAYER STACK
EVENTS
ARM7
CPU
COMMANDS
HCI
LM
FLASH
MEMORY
BASEBAND
RF
HCI STACK
©2008
Amp’ed RF Inc
2
9/30/08
1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA
www.ampedrf.com
BT-210 Datasheet
Page 2 of 7
Amp’ed RF, Inc.
(phone) 408 213-9530
(fax) 408 213-9533
Driver Installation
Windows XP Installation Instructions:
Step 1
Simply plug in the BT-210 into any available USB port.
The computer will respond with the following two
messages...
Step 2
Next, Windows will launch a "Found New Hardware
Wizard" installation window.
Select YES to locate the drivers from the Microsoft
website.
©2008
Amp’ed RF Inc
3
9/30/08
1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA
www.ampedrf.com
BT-210 Datasheet
Page 3 of 7
Amp’ed RF, Inc.
(phone) 408 213-9530
(fax) 408 213-9533
Click NEXT to install automatically.
Now the BT-210 USB to UART Controller and Virtual
©2008
Amp’ed RF Inc
4
9/30/08
1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA
www.ampedrf.com
BT-210 Datasheet
Page 4 of 7
Amp’ed RF, Inc.
(phone) 408 213-9530
(fax) 408 213-9533
COM port driver is installed.
©2008 Amp’ed RF Inc
5
9/30/08
1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA
www.ampedrf.com
BT-210 Datasheet
Page 5 of 7
Amp’ed RF, Inc.
(phone) 408 213-9530
(fax) 408 213-9533
Step 3
The "Found New Hardware Wizard" will now open
again in order to install the USB device driver.
Select YES to locate the drivers from the Microsoft
website.
You will now see the following message.
©2008
Amp’ed RF Inc
6
9/30/08
1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA
www.ampedrf.com
BT-210 Datasheet
Page 6 of 7
Amp’ed RF, Inc.
(phone) 408 213-9530
(fax) 408 213-9533
Step 4
You may open the Windows Device Manager application to verify correct installation, and see which COM
port has been assigned to your BT-210 Bluetooth serial device. The BT-210 will usually be assigned the
same virtual COM port each time it is inserted (unless you have other virtual COM devices altering port
assignments).
You should see the two device drivers for your BT-210 Bluetooth device here
The CP2102 chip provides the functionality to use standard UART serial communications from your computer
via the Universal Serial Bus, and interfaces directly to our Bluetooth module inside the BT-210 Bluetooth
serial adapter.
©2008
Amp’ed RF Inc
7
9/30/08
1722 Ringwood Ave, Suite 250, San Jose, CA 95131, USA
www.ampedrf.com
BT-210 Datasheet
Page 7 of 7
Similar pages