1733 Reader's Spreadspg189-328:1570 Reader's Spreadspg189-328 1/27/09 4:59 PM Page 63 FBA ferrite bead array EU features • Noise suppression in signal I/O lines and other circuits that require multiple chip beads for noise suppression • Multiple circuits in a single package • Marking: Black body color with no marking • Products with lead-free terminations meet EU RoHS requirements dimensions and construction L a Type p (Inch Size Code) b W 1J (0603) L W Dimensions inches (mm) t a b p .126±.008 .063±.008 .031±.008 .016±.008 .012±.008 .031±.008 (3.2±0.2) (1.6±0.2) (0.8±0.2) (0.40±0.2) (0.3±0.2) (0.8±0.2) t Protective Coating Solder Plating ordering information New Part # FBA 1J 4 A Type Size Circuits Characteristics 1J: 0603 Number of circuits A: Standard B: High speed T Termination Material T: Sn TE 300 P Packaging Impedance Tolerance TE: 7" embossed plastic (3,000 pieces/reel) 2 significant figures + 1 multiplier Ex: 300 = 30Ω P: ±25% EMI/EMC filtering circuit schematic For further information on packaging, please refer to Appendix A. Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 258 2/24/08 KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com 1733 Reader's Spreadspg189-328:1570 Reader's Spreadspg189-328 1/27/09 4:59 PM Page 64 PMS 300 neg. Black neg. FBA ferrite bead array applications and ratings NEW Impedance @ 100MHz (Ω) FBA1J4ATTE300P FBA1J4ATTE600P FBA1J4ATTE121P FBA1J4ATTE221P FBA1J4ATTE301P FBA1J4ATTE601P FBA1J4ATTE102P FBA1J4BTTE300P FBA1J4BTTE600P FBA1J4BTTE121P FBA1J4BTTE221P FBA1J4BTTE301P FBA1J4BTTE601P 30 60 120 220 300 600 1000 30 60 120 220 300 600 DC Resistance Maximum (Ω) 0.1 0.25 0.3 0.4 0.5 0.7 0.25 0.3 0.4 0.45 0.50 0.65 Allowable DC Current Per Element Maximum (mA) 200 400 350 Operating Temperature Range 250 100 200 400 350 -55°C to +125°C 100 150 100 environmental applications Performance Characteristics Requirement Parameter Test Method Operating Temperature -55°C to +125°C Storage Temperature 40°C @ 70% humidity Sealed plastic bags with desiccant shall be used to reduce the potential of oxidation on the terminations during storage. Resistance to Solder Heat Change in Impedance: Relative to value before test ±20% Appearance: There shall be no cracking. Solder Coverage: More than 75% of the terminal electrode shall be covered with solder. Flux: 5 - 10 second dip After Flux: Air dry for 15 seconds Preheat: 150°C ± 10°C Preheat Time: 60 seconds Solder Temperature: 260°C ± 5°C Dip Time: 10 ± 1 second Solderability Solder Coverage: More than 95% of the termination shall be covered with solder. Flux: 5 - 10 second dip After Flux: Air dry for 15 seconds Solder Temperature: 245°C ± 5°C Dip Time: 5 ± 0.5 second Leach Resistance Appearance: There shall be no visible signs of physical or mechanical damage (i.e. no cracks). Terminations: Termination must not be leached away for more than 5%. The bead shall be subjected to the following 5 steps for the period of time shown below. The 5 steps constitute one (1) rotation. 4 rotations shall be carried out. 1) Flux: 5 - 10 seconds 2) After Flux: Air dry for 15 seconds 3) Solder Temperature: 230°C ± 5°C 4) Dip Time: 5 ± 0.5 second 5) Cool: Air cool for 60 seconds Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 3/05/07 KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com 259 EMI/EMC filtering NEW Part Designation 1733 Reader's Spreadspg189-328:1570 Reader's Spreadspg189-328 1/27/09 4:59 PM Page 65 FBA ferrite bead array environmental applications (continued) Performance Characteristics Parameter Requirement Test Method EMI/EMC filtering Insulation Resistance Insulation Resistance: Min. 1G ohms Solvent Resistance Change in Impedance: Relative to value before test ±10% Cleaning by: Washer: Ultrasonic washer (100W) Solvent: Isopropyl alcohol Time: 3 minutes Terminal Strength (hanging test) Appearance: The terminal electrode shall not break off, nor shall there be damage to the body. Type: 1206 W(kgf): 1.5 Time: 30 seconds ± 2 seconds Terminal Strength (push test) Appearance: There shall be no evidence of mechanical degradations to terminals or body. Type: 1206 W(kgf): 2.3 Time: 60 seconds Bending Strength Appearance: There shall be no physical or mechanical damage. Impedance: Relative to initial value before test ±10% Board: 90 x 40 x 1.6mm Bend: 1mm Time: 5 sec Mechanical Shock Appearance: There shall be no physical or mechanical damage. Impedance: Relative to initial value before test ±10% Force: 50G Time: 11 msec There shall be 3 shocks in each of 6 directions (18 shocks total) Vibration Impedance: Relative to initial value ±10% Only endurance conditioning by sweeping shall be made. The entire frequency range from 10 - 2,000 Hz, return to 10 Hz in 20 minutes (this will constitute one cycle). Amplitude: 15G The test shall have a 15G peak and shall be applied for a period of 4 hours (12 cycles) in each of 3 mutually perpendicular directions (a total of 36 cycles within a total of 12 hours). Thermal Shock Appearance: There shall be no physical or mechanical damage. Impedance: Relative to initial value ±20% DCR: The DCR shall not exceed initial specified value. Testing of the parts will be made at 0 hours, 250 hours and 500 hours. Before testing, the parts shall be allowed to cool to room temperature for 24 hours. Step: Temperature: Time: 1-start -40°C ± 2°C — 2-hold -40°C ± 2°C 30 minutes ± 5 minutes 3-transfer — 0.5 minutes maximum 4-hold ±105°C ± 2°C 30 minutes ± 5 minutes 5-transfer — 0.5 minutes maximum Steps 1 thru 5 constitute one complete cycle and the test shall consist of a total of 500 cycles. Load Humidity Appearance: There shall be no physical or mechanical damage. Impedance: Relative to initial value ±15% Measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. Temperature: ±85°C ± 2°C Relative Humidity: 85% Time: 1,000 hours total Apply: 100% rated current Life Test Appearance: There shall be no physical or mechanical damage. Impedance: Relative to initial value ±15% Measurements shall be taken at 0 hours, 250 hours, 500 hours and 1,000 hours and shall meet the conditions stated above. Temperature: ±85°C ± 2°C Time: 1,000 hours total Apply: 100% rated current Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. 260 3/01/07 KOA Speer Electronics, Inc. • 199 Bolivar Drive • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com