CY28419 Clock Synthesizer with Differential SRC and CPU Outputs Features • Four differential CPU clock pairs • One differential SRC clock • CK409B-compliant • I2C support with readback capabilities • Supports Intel Pentium£ 4-type CPUs • Selectable CPU frequencies • Ideal Lexmark Spread Spectrum profile for maximum electromagnetic interference (EMI) reduction • 3.3V power supply • 56-pin SSOP package • Ten copies of PCI clocks • Two copies 48 MHz clock CPU SRC 3V66 PCI REF 48M x4 x1 x5 x 10 x2 x2 • Five copies of 3V66 with one optional VCH [1] Block Diagram XIN XOUT Pin Configuration VDD_REF REF0:1 XTAL OSC PLL 1 PLL Ref Freq VDD_CPU CPUT(0:3), CPUC(0:3) Divider Network VDD_SRC SRCT, SRCC FS_(A:B) VTT_PWRGD# IREF VDD_PCI PCIF(0:2) PLL2 2 PCI(0:6) 3V66_4/VCH VDD_48MHz DOT_48 PD# USB_48 SDATA SCLK I2C Logic 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 CY28419 VDD_3V66 3V66_(0:3) REF_0 REF_1 VDD_REF XIN XOUT VSS_REF PCIF0 PCIF1 PCIF2 VDD_PCI VSS_PCI PCI0 PCI1 PCI2 PCI3 VDD_PCI VSS_PCI PCI4 PCI5 PCI6 PD# 3V66_0 3V66_1 VDD_3V66 VSS_3V66 3V66_2 3V66_3 SCLK FS_B VDD_A VSS_A VSS_IREF IREF FS_A CPUT3 CPUC3 VDD_CPU CPUT2 CPUC2 VSS_CPU CPUT1 CPUC1 VDD_CPU CPUT0 CPUC0 VSS_SRC SRCT SRCC VDD_SRC VTT_PWRGD# VDD_48 VSS_48 DOT_48 USB_48 SDATA 3V66_4/VCH SSOP-56 Note: 1. Signals marked with [*] and [**] have internal pull-up and pull-down resistors, respectively. Rev 1.0, November 22, 2006 2200 Laurelwood Road, Santa Clara, CA 95054 Page 1 of 15 Tel:(408) 855-0555 Fax:(408) 855-0550 www.SpectraLinear.com CY28419 Pin Description Pin No. Pin Name Pin Type O, SE Pin Description 1,2 REF(0:1) 4 XIN 5 XOUT O, SE Crystal Connection. Connection for an external 14.318-MHz crystal output. 41,44,47,50 CPUT(0:3) O, DIF CPU Clock Output. Differential CPU clock outputs. See Table 1 for frequency configuration. 40,43,46,49 CPUC(0:3) O, DIF CPU Clock Output. Differential CPU clock outputs. See Table 1 for frequency configuration. 38, 37 SRCT, SRCC O, DIF Differential serial reference clock. I Reference Clock. 3.3V 14.318-Mz clock output. Crystal Connection or External Reference Frequency Input. This pin has dual functions. It can be used as an external 14.318-MHz crystal connection or as an external reference frequency input. 22,23,26,27 3V66(3:0) O, SE 66 MHz Clock Output. 3.3V 66-MHz clock from internal VCO. 29 3V66_4VCH O, SE 48/66 MHz Clock Output. 3.3V selectable through SMBus to be 66 or 48 MHz. 7,8,9 PCIF(0:2) O, SE Free Running PCI Output. 33-MHz clocks divided down from 3V66. 12,13,14,15, PCI(0:6) 18,19,20 O, SE PCI Clock Output. 33-MHz clocks divided down from 3V66. 31, USB_48 O, SE Fixed 48 MHz clock output. 32 DOT_48 O, SE Fixed 48 MHz clock output. 51,56 FS_A, FS_B I 3.3V LVTTL input for CPU frequency selection. 52 IREF I Current Reference. A precision resistor is attached to this pin which is connected to the internal current reference. 21 PD# I, PU 35 VTT_PWRGD# 30 SDATA I I/O 3.3V LVTTL input for power-down# active LOW. 3.3V LVTTL input is a level-sensitive strobe used to latch the FS0 input (active LOW). SMBus-compatible SDATA. 28 SCLK I SMBus-compatible SCLOCK. 53 VSS_IREF GND Ground for current reference. 55 VDD_A PWR 3.3V power supply for PLL. 54 VSS_A GND Ground for PLL. 42,48 VDD_CPU PWR 3.3V power supply for outputs. 45 VSS_CPU GND Ground for outputs. 36 VDD_SRC PWR 3.3V power supply for outputs. 39 VSS_SRC GND Ground for outputs. 34 VDD_48 PWR 3.3V power supply for outputs. 33 VSS_48 GND Ground for outputs. 10,16 VDD_PCI PWR 3.3V power supply for outputs. 11,17 VSS_PCI GND Ground for outputs. 24 VDD_3V66 PWR 3.3V power supply for outputs. 25 VSS_3V66 GND Ground for outputs. 3 VDD_REF PWR 3.3V power supply for outputs. 6 VSS_REF GND Ground for outputs. Rev 1.0, November 22, 2006 Page 2 of 15 CY28419 Frequency Select Pins (FS_A, FS_B) Host clock frequency selection is achieved by applying the appropriate logic levels to FS_A and FS_B inputs prior to VTT_PWRGD# assertion (as seen by the clock synthesizer). Upon VTT_PWRGD# being sampled low by the clock chip (indicating processor VTT voltage is stable), the clock chip samples the FS_A and FS_B input values. For all logic levels of FS_A and FS_B except MID, VTT_PWRGD# employs a one-shot functionality in that once a valid low on VTT_PWRGD# has been sampled low, all further VTT_PWRGD#, FS_A and FS_B transitions will be ignored. In the case where FS_B is at mid level when VTT_PWRGD# is sampled low, the clock chip will assume “Test Clock Mode”. Once “Test Clock Mode” has been invoked, all further FS_B transitions will be ignored and FS_A will asynchronously select between the Hi-Z and REF/N mode. Exiting test mode is accomplished by cycling power with FS_B in a high or low state. Table 1. Frequency Select Table (FS_A FS_B) FS_A FS_B CPU SRC 3V66 PCIF/PCI REF0 REF1 USB/DOT 0 0 100 MHz 100/200 MHz 66 MHz 33 MHz 14.3 MHz 14.31 MHz 48 MHz 0 MID REF/N REF/N REF/N REF/N REF/N REF/N REF/N 0 1 200 MHz 100/200 MHz 66 MHz 33 MHz 14.3 MHz 14.31 MHz 48 MHz 1 0 133 MHz 100/200 MHz 66 MHz 33 MHz 14.3 MHz 14.31 MHz 48 MHz 1 1 166 MHz 100/200 MHz 66 MHz 33 MHz 14.3 MHz 14.31 MHz 48 MHz 1 MID Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Table 2. Frequency Select Table (FS_A FS_B) SMBus Bit 5 of Byte 6 = 1 FS_A FS_B CPU SRC 3V66 PCIF/PCI REF0 REF1 USB/DOT 0 0 200 MHz 100/200 MHz 66 MHz 33 MHz 14.3 MHz 14.31 MHz 48 MHz 0 1 400 MHz 100/200 MHz 66 MHz 33 MHz 14.3 MHz 14.31 MHz 48 MHz 1 0 266 MHz 100/200 MHz 66 MHz 33 MHz 14.3 MHz 14.31 MHz 48 MHz 1 1 333 MHz 100/200 MHz 66 MHz 33 MHz 14.3 MHz 14.31 MHz 48 MHz Serial Data Interface To enhance the flexibility and function of the clock synthesizer, a two-signal serial interface is provided. Through the Serial Data Interface, various device functions, such as individual clock output buffers, can be individually enabled or disabled. The registers associated with the Serial Data Interface initializes to their default setting upon power-up, and therefore use of this interface is optional. Clock device register changes are normally made upon system initialization, if any are required. The interface cannot be used during system operation for power management functions. first) with the ability to stop after any complete byte has been transferred. For byte write and byte read operations, the system controller can access individually indexed bytes. The offset of the indexed byte is encoded in the command code, as described in Table 3. The block write and block read protocol is outlined in Table 4 while Table 5 outlines the corresponding byte write and byte read protocol. The slave receiver address is 11010010 (D2h). Table 3. Command Code Definition Bit Description 7 0 = Block read or block write operation, 1 = Byte read or byte write operation (6:0) Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be '0000000' Data Protocol The clock driver serial protocol accepts byte write, byte read, block write, and block read operations from the controller. For block write/read operation, the bytes must be accessed in sequential order from lowest to highest byte (most significant bit Table 4. Block Read and Block Write Protocol Block Write Protocol Bit 1 2:8 Description Start Slave address – 7 bits Block Read Protocol Bit 1 2:8 Description Start Slave address – 7 bits 9 Write = 0 9 Write = 0 10 Acknowledge from slave 10 Acknowledge from slave 11:18 Command Code – 8 bits '00000000' stands for block operation Rev 1.0, November 22, 2006 11:18 Command Code – 8 bits '00000000' stands for block operation Page 3 of 15 CY28419 Table 4. Block Read and Block Write Protocol (continued) Block Write Protocol 19 20:27 28 29:36 37 38:45 Block Read Protocol Acknowledge from slave 19 Acknowledge from slave Byte Count – 8 bits 20 Repeat start Acknowledge from slave 21:27 Slave address – 7 bits Data byte 1 – 8 bits 28 Read = 1 Acknowledge from slave 29 Acknowledge from slave Data byte 2 – 8 bits 30:37 38 Byte count from slave – 8 bits 46 Acknowledge from slave .... ...................... .... Data Byte (N–1) –8 bits 47 .... Acknowledge from slave 48:55 .... Data Byte N –8 bits 56 Acknowledge from master .... Acknowledge from slave .... Data byte N from slave – 8 bits .... Stop .... Acknowledge from master .... Stop 39:46 Acknowledge from master Data byte from slave – 8 bits Acknowledge from master Data byte from slave – 8 bits Table 5. Byte Read and Byte Write Protocol Byte Write Protocol Bit 1 2:8 Description Start Slave address – 7 bits Byte Read Protocol Bit 1 2:8 Description Start Slave address – 7 bits 9 Write = 0 9 Write = 0 10 Acknowledge from slave 10 Acknowledge from slave 11:18 19 20:27 Command Code – 8 bits '100xxxxx' stands for byte operation, bits[6:0] of the command code represents the offset of the byte to be accessed 11:18 Command Code – 8 bits '100xxxxx' stands for byte operation, bits[6:0] of the command code represents the offset of the byte to be accessed Acknowledge from slave 19 Acknowledge from slave Data byte from master – 8 bits 20 Repeat start 28 Acknowledge from slave 29 Stop 21:27 Read = 1 29 Acknowledge from slave 30:37 Rev 1.0, November 22, 2006 Slave address – 7 bits 28 Data byte from slave – 8 bits 38 Acknowledge from master 39 Stop Page 4 of 15 CY28419 Byte 0: Control Register 0 Bit @Pup 7 0 Reserved Name Reserved Description 6 1 Reserved Reserved 5 0 Reserved Reserved 4 0 Reserved Reserved 3 1 Reserved Reserved 2 1 Reserved Reserved 1 Externally Selected FS_B FS_B reflects the value of the FS_B pin sampled on power-up. 0 = FS_B low at power-up 0 Externally Selected FS_A FS_A reflects the value of the FS_A pin sampled on power-up. 0 = FS_A low at power-up Byte 1: Control Register 1 Bit @Pup 7 0 SRCT, SRCC Name Allow control of SRCT/C with assertion of PCI_STP# 0 = Free Running, 1 = Stopped with PCI_STP# Description 6 1 SRCT, SRCC SRCT/C Output Enable 0 = Disabled (three-state), 1 = Enabled 5 1 Reserved Reserved 4 1 Reserved Reserved 3 1 Reserved Reserved 2 1 CPUT2, CPUC2 CPUT/C2 Output Enable 0 = Disabled (three-state), 1 = Enabled 1 1 CPUT1, CPUC1 CPUT/C1 Output Enable, 0 = Disabled (three-state), 1 = Enabled 0 1 CPUT0, CPUC0 CPUT/C0 Output Enable 0 = Disabled (three-state), 1 = Enabled Byte 2: Control Register 2 Bit @Pup 7 0 SRCT, SRCC Name SRCT/C Pwrdwn drive mode 0 = Driven in power-down, 1 = Three-state in power-down 6 0 SRCT, SRCC SRCT/C Stop drive mode 0 = Driven in PCI_STP, 1 = Three-state in power-down 5 0 CPUT2, CPUC2 CPUT/C2 Pwrdwn drive mode 0 = Driven in power-down, 1 = Three-state in power-down 4 0 CPUT1, CPUC1 CPUT/C1 Pwrdwn drive mode 0 = Driven in power-down, 1 = Three-state in power-down 3 0 CPUT0, CPUC0 CPUT/C0 Pwrdwn drive mode 0 = Driven in power-down, 1 = Three-state in power-down 2 0 Reserved Reserved 1 0 Reserved Reserved 0 0 Reserved Reserved Rev 1.0, November 22, 2006 Description Page 5 of 15 CY28419 Byte 3: Control Register 3 Bit @Pup Name 7 1 All PCI and SRC Clock outputs except PCIF and SRC clocks set to free-running 6 1 PCI6 5 1 PCI5 4 1 PCI4 3 1 PCI3 2 1 PCI2 1 1 PCI1 0 1 PCI0 Description PCI_STP Control. 0 = SW PCI_STP not enabled and only the PCI_STP# pin will stop the PCI stop enabled outputs, 1 = the PCI_STP function is enabled and the stop enabled outputs will be stopped in a synchronous manner with no short pulses. PCI6 Output Enable 0 = Disabled, 1 = Enabled PCI5 Output Enable 0 = Disabled, 1 = Enabled PCI4 Output Enable 0 = Disabled, 1 = Enabled PCI3 Output Enable 0 = Disabled, 1 = Enabled PCI2 Output Enable 0 = Disabled, 1 = Enabled PCI1 Output Enable 0 = Disabled, 1 = Enabled PCI0 Output Enable 0 = Disabled, 1 = Enabled Byte 4: Control Register 4 Bit 7 @Pup 0 Name USB_ 48MHz 6 1 USB_ 48MHz 5 0 PCIF2 4 0 PCIF1 3 0 PCIF0 2 1 PCIF2 1 1 PCIF1 0 1 PCIF0 Description USB_48 Drive Strength 0 = High drive strength, 1 = Normal drive strength USB_48 Output Enable 0 = Disabled, 1 = Enabled Allow control of PCIF2 with assertion of PCI_STP# 0 = Free Running, 1 = Stopped with PCI_STP# Allow control of PCIF1 with assertion of PCI_STP# 0 = Free Running, 1 = Stopped with PCI_STP# Allow control of PCIF0 with assertion of PCI_STP# 0 = Free Running, 1 = Stopped with PCI_STP# PCIF2 Output Enable 0 = Disabled, 1 = Enabled PCIF1 Output Enable 0 = Disabled, 1 = Enabled PCIF0 Output Enable 0 = Disabled, 1 = Enabled Byte 5: Control Register 5 Bit @Pup 7 1 DOT_48 Name DOT_48 Output Enable 0 = Disabled, 1 = Enabled 6 1 CPUT3, CPUC3 0 = three-state, 1 = Enabled 5 0 3V66_4/VCH VCH Select 66 MHz/48 MHz 0 = 3V66 mode, 1 = VCH (48MHz) mode 4 1 3V66_4/VCH 3V66_4/VCH Output Enable 0 = Disabled, 1 = Enabled 3 1 3V66_3 3V66_3 Output Enable 0 = Disabled, 1 = Enabled 2 1 3V66_2 3V66_2 Output Enable 0 = Disabled, 1 = Enabled 1 1 3V66_1 3V66_1 Output Enable 0 = Disabled, 1 = Enabled 0 1 3V66_0 3V66_0 Output Enable 0 = Disabled, 1 = Enabled Rev 1.0, November 22, 2006 Description Page 6 of 15 CY28419 Byte 6: Control Register 6 Bit @Pup 7 0 Name Description Test Clock Mode 0= Disabled, 1 = Enabled REF PCIF PCI 3V66 USB_48 DOT_48 CPUT/C SRCT/C 6 0 5 0 CPUC0, CPUT0 CPUC1, CPUT1 CPUC2, CPUT2 CPUC3, CPUT3 Reserved, Set = 0 FS_A & FS_B Operation 0 = Normal, 1 = Test mode 4 0 SRCT, SRCC SRC Frequency Select 0 = 100 MHz, 1 = 200 MHz 3 0 2 0 PCIF PCI 3V66 SRC(T/C) CPUT/ C Spread Spectrum Mode 0 = Spread Off, 1 = Spread On 1 1 REF_1 REF_1 Output Enable 0 = Disabled, 1 = Enabled 0 1 REF_0 REF_0 Output Enable 0 = Disabled, 1 = Enabled Reserved, Set = 0 Byte 7: Vendor ID Bit @Pup Name Description 7 0 Revision Code Bit 3 Revision Code Bit 3 6 0 Revision Code Bit 2 Revision Code Bit 2 5 0 Revision Code Bit 1 Revision Code Bit 1 4 0 Revision Code Bit 0 Revision Code Bit 0 3 1 Vendor ID Bit 3 Vendor ID Bit 3 2 0 Vendor ID Bit 2 Vendor ID Bit 2 1 0 Vendor ID Bit 1 Vendor ID Bit 1 0 0 Vendor ID Bit 0 Vendor ID Bit 0 Crystal Recommendations The CY28419 requires a Parallel Resonance Crystal. Substituting a series resonance crystal will cause the CY28419 to operate at the wrong frequency and violate the ppm specification. For most applications there is a 300-ppm frequency shift between series and parallel crystals due to incorrect loading. Table 6. Crystal Recommendations Frequency (Fund) Cut Loading Load Cap Drive (max.) Shunt Cap (max.) Motional (max.) Tolerance (max.) Stability (max.) Aging (max.) 14.31818 MHz AT Parallel 0.1 mW 5 pF 0.016 pF 50 ppm 50 ppm 5 ppm Rev 1.0, November 22, 2006 20 pF Page 7 of 15 CY28419 Crystal Loading Crystal loading plays a critical role in achieving low ppm performance. To realize low-ppm performance, the total capacitance the crystal will see must be considered to calculate the appropriate capacitive loading (CL). The following diagram shows a typical crystal configuration using the two trim capacitors. An important clarification for the following discussion is that the trim capacitors are in series with the crystal not parallel. It’s a common misconception that load capacitors are in parallel with the crystal and should be approximately equal to the load capacitance of the crystal. This is not true. As mentioned previously, the capacitance on each side of the crystal is in series with the crystal. This mean the total capacitance on each side of the crystal must be twice the specified load capacitance(CL). While the capacitance on each side of the crystal is in series with the crystal, trim capacitors(Ce1,Ce2) should be calculated to provide equal capacitative loading on both sides. Use the following formulas to calculate the trim capacitor values fro Ce1 and Ce2. Load Capacitance (each side) Ce = 2 * CL – (Cs + Ci) Total Capacitance (as seen by the crystal) CLe = 1 1 ( Ce1 + Cs1 + Ci1 + 1 Ce2 + Cs2 + Ci2 ) CL....................................................Crystal load capacitance CLe......................................... Actual loading seen by crystal ..................................... using standard value trim capacitors Ce..................................................... External trim capacitors Figure 1. Crystal Capacitive Clarification Calculating Load Capacitors In addition to the standard external trim capacitors, trace capacitance and pin capacitance must also be considered to correctly calculate crystal loading. As mentioned previously, the capacitance on each side of the crystal is in series with the crystal. This means the total capacitance on each side of the crystal must be twice the specified crystal load capacitance (CL). While the capacitance on each side of the crystal is in series with the crystal, trim capacitors (Ce1,Ce2) should be calculated to provide equal capacitive loading on both sides. Clock Chip (CY28419) Ci2 Ci1 Pin 3 to 6p X2 X1 Cs1 Cs ........................................... Stray capacitance (trace, etc.) Ci ...........................................................Internal capacitance ................................................ (lead frame, bond wires, etc.) PD# (Power-down) Clarification The PD# pin is used to shut off all clocks and PLLs without having to remove power from the device. All clocks are shut down in a synchronous manner so has not to cause glitches while transitioning to the power-down state. PD#–Assertion When PD# is sampled low by two consecutive rising edges of the CPUC clock then all clock outputs (except CPU) clocks must be held low on their next high to low transition. CPU clocks must be held with CPUT clock pin driven high with a value of 2x Iref and CPUC undriven as the default condition. There exists an I2C bit that allows for the CPUT/C outputs to be three-stated during power-down. Due to the state of internal logic, stopping and holding the REF clock outputs in the LOW state may require more than one clock cycle to complete. Cs2 Trace 2.8pF XTAL Ce1 Ce2 Trim 33pF Figure 2. Crystal Loading Example Rev 1.0, November 22, 2006 Page 8 of 15 CY28419 PD# CPUT, 133MHz CPUC, 133MHz SRCT 100MHz SRCC 100MHz 3V66, 66MHz USB, 48MHz PCI, 33MHz REF Figure 3. Power-down Assertion Timing Waveforms PD# Deassertion The power-up latency between PD# rising to a valid logic ‘1’ level and the starting of all clocks is less than 1.8 ms. The CPUT/C outputs must be driven to greater than 200 mV is less than 300 us. Tstable <1.8ms PD# CPUT, 133MHz CPUC, 133MHz SRCT 100MHz SRCC 100MHz 3V66, 66MHz USB, 48MHz PCI, 33MHz REF Tdrive_PWRDN# <300PS, >200mV Figure 4. Power-down Deassertion Timing Waveforms Rev 1.0, November 22, 2006 Page 9 of 15 CY28419 FS_A, FS_B VTT_PWRGD# PWRGD_VRM 0.2-0.3mS Delay VDD Clock Gen Clock State Clock Outputs Clock VCO State 0 Wait for VTT_PWRGD# State 1 Device is not affected, VTT_PWRGD# is ignored Sample Sels State 2 Off State 3 On On Off Figure 5. VTTPWRGD Timing Diagram S2 S1 Delay >0.25mS VTT_PWRGD# = Low Sample Inputs straps VDD_A = 2.0V Wait for <1.8ms S0 Power Off S3 VDD_A = off Normal Operation Enable Outputs VTT_PWRGD# = toggle Figure 6. Clock Generator Power-up/Run State Diagram Rev 1.0, November 22, 2006 Page 10 of 15 CY28419 Absolute Maximum Conditions Parameter Description Condition Min. Max. Unit VDD Core Supply Voltage –0.5 4.6 V VDD_A Analog Supply Voltage –0.5 4.6 V VIN Input Voltage Relative to V SS –0.5 VDD + 0.5 VDC TS Temperature, Storage Non-functional –65 +150 °C TA Temperature, Operating Ambient Functional 0 70 °C TJ Temperature, Junction Functional – 150 °C ØJC Dissipation, Junction to Case Mil-Spec 883E Method 1012.1 – 15 °C/W ØJA Dissipation, Junction to Ambient JEDEC (JESD 51) – 45 °C/W ESDHBM ESD Protection (Human Body Model) MIL-STD-883, Method 3015 – V UL-94 Flammability Rating At 1/8 in. MSL Moisture Sensitivity Level 2000 V–0 1 Multiple Supplies: The Voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required. DC Electrical Specifications Parameter Description Conditions VDD, VDD_A 3.3 Operating Voltage 3.3V ± 5% VILI2C Input Low Voltage SDATA, SCLK VIHI2C Input High Voltage SDATA, SCLK VIL Input Low Voltage VIH Input High Voltage IIL Input Leakage Current IILI2C VOL Min. Max. Unit 3.135 3.465 V – 1.0 V 2.2 – V VSS – 0.5 0.8 V 2.0 VDD + 0.5 V except Pull-ups or Pull-downs 0 < VIN < VDD –5 5 PA Input High Voltage SDATA, SCLK 2.2 – V Output Low Voltage IOL = 1 mA – 0.4 V IOH = –1 mA VOH Output High Voltage IOZ High-impedance Output Current CIN Input Pin Capacitance 2 5 pF COUT Output Pin Capacitance 3 6 pF LIN Pin Inductance VXIH Xin High Voltage VXIL Xin Low Voltage IDD Dynamic Supply Current At 200 MHz and all outputs loaded per Table 9 and Figure 7 IPD Power-down Supply Current PD# asserted, Outputs Three-stated 2.4 – V –10 10 PA – 7 nH 0.7VDD VDD V 0 0.3VDD V – 280 mA – 1 mA Conditions Min. Max. Unit The device will operate reliably with input duty cycles up to 30/70 but the REF clock duty cycle will not be within specification 47.5 52.5 % AC Electrical Specifications Parameter Description Crystal TDC XIN Duty Cycle TPERIOD XIN Period When XIN is driven from an external clock source 69.841 71.0 ns T R / TF XIN Rise and Fall Times Measured between 0.3VDD and 0.7VDD – 10.0 ns TCCJ XIN Cycle-to-Cycle Jitter As an average over 1-Ps duration – 500 ps LACC Long-term Accuracy Over 150 ms – 300 ppm Rev 1.0, November 22, 2006 Page 11 of 15 CY28419 AC Electrical Specifications (continued) Parameter Description CPU at 0.7V TDC CPUT and CPUC Duty Cycle Conditions Measured at crossing point VOX Min. Max. Unit 45 55 % TPERIOD 100-MHz CPUT and CPUC Period Measured at crossing point VOX 9.9970 10.003 ns TPERIOD 133-MHz CPUT and CPUC Period Measured at crossing point VOX 7.4978 7.5023 ns TPERIOD 166-MHz CPUT and CPUC Period Measured at crossing point VOX 5.9982 6.0018 ns TPERIOD 200-MHz CPUT and CPUC Period Measured at crossing point VOX 4.9985 5.0015 ns TSKEW Any CPU to CPU Clock Skew Measured at crossing point VOX – 100 ps TCCJ CPU Cycle-to-Cycle Jitter Measured at crossing point VOX – 125 ps 175 700 ps – 20 % TR/TF CPUT/CPUC Rise and Fall Times Measured from VOL = 0.175 to VOH = 0.525V TRFM Rise/Fall Matching Determined as a fraction of 2*(TR–TF)/ (TR+TF) 'TR Rise Time Variation – 125 ps 'TF Fall Time Variation – 125 ps VHIGH Voltage High Math average, see Figure 7 660 850 mv VLOW Voltage Low Math average, see Figure 7 –150 – mv VOX Crossing Point voltage at 0.7V Swing 250 550 mv VOVS Maximum Overshoot Voltage – VHIGH + 0.3 V VUDS Minimum Undershoot Voltage –0.3 – V VRB Ring Back Voltage See Figure 7. Measure SE – 0.2 V SRC TDC SRCT and SRCC Duty Cycle Measured at crossing point VOX 45 55 % TPERIOD 100-MHz SRCT and SRCC Period Measured at crossing point VOX 9.9970 10.003 ns TPERIOD 200-MHz SRCT and SRCC Period Measured at crossing point VOX 4.9985 5.0015 ns TCCJ SRC Cycle-to-Cycle Jitter Measured at crossing point VOX – 125 ps LACC SRCT/C Long-term Accuracy Measured at crossing point VOX – 300 ppm T R / TF SRCT/SRCT\C Rise and Fall Times Measured from VOL = 0.175 to VOH = 0.525V 175 700 ps TRFM Rise/Fall Matching – 20 % 'TR Rise Time Variation – 125 ps 'TF Fall Time Variation – 125 ps Determined as a fraction of 2*(TR–TF)/ (TR+TF) VHIGH Voltage High Math average, see Figure 7 660 850 mv VLOW Voltage Low Math average, see Figure 7 –150 – mv VOX Crossing Point Voltage at 0.7V Swing 250 550 mV VOVS Maximum Overshoot Voltage – VHIGH+0.3 V VUDS Minimum Undershoot Voltage –0.3 – V VRB Ring Back Voltage See Figure 7. Measure SE – 0.2 V 3V66 TDC 3V66 Duty Cycle Measurement at 1.5V 45 55 % TPERIOD Spread Disabled 3V66 Period Measurement at 1.5V 14.9955 15.0045 ns TPERIOD Spread Enabled 3V66 Period Measurement at 1.5V 14.9955 15.0799 ns THIGH 3V66 High Time Measurement at 2.0V 4.9500 – ns TLOW 3V66 Low Time Measurement at 0.8V 4.5500 – ns T R / TF 3V66 Rise and Fall Times Measured between 0.8V and 2.0V 0.5 2.0 ns TSKEW Any 3V66 to Any 3V66 Clock Skew Measurement at 1.5V – 250 ps TCCJ 3V66 Cycle-to-Cycle Jitter – 250 ps Rev 1.0, November 22, 2006 Measurement at 1.5V Page 12 of 15 CY28419 AC Electrical Specifications (continued) Parameter Description Conditions PCI / PCIF TDC PCIF and PCI Duty Cycle Measurement at 1.5V Min. Max. Unit 45 55 % TPERIOD Spread Disabled PCIF/PCI Period Measurement at 1.5V 29.9910 30.0009 ns TPERIOD Spread Enabled PCIF/PCI Period Measurement at 1.5V 29.9910 30.1598 ns THIGH PCIF and PCI High Time Measurement at 2.0V 12.0 – nS TLOW PCIF and PCI Low Time Measurement at 0.8V 12.0 – nS T R / TF PCIF and PCI rise and fall times Measured between 0.8V and 2.0V 0.5 2.0 nS TSKEW Any PCI Clock to Any PCI Clock Skew Measurement at 1.5V – 500 pS TCCJ PCIF and PCI Cycle-to-Cycle Jitter Measurement at 1.5V – 250 ps DOT TDC DOT Duty Cycle Measurement at 1.5V 45 55 % TPERIOD DOT Period Measurement at 1.5V 20.8257 20.8340 ns THIGH DOT High Time Measurement at 2.0V 8.994 10.486 nS TLOW DOT Low Time Measurement at 0.8V 8.794 10.386 nS T R / TF Rise and Fall Times Measured between 0.8V and 2.0V 0.5 1.0 ns TLTJ Long-term Jitter 10-Ps period – 2.0 ns USB TDC USB Duty Cycle Measurement at 1.5V 45 55 % TPERIOD USB Period Measurement at 1.5V 20.8257 20.8340 ns THIGH USB High Time Measurement at 2.0V 8.094 10.036 nS TLOW USB Low Time Measurement at 0.8V 7.694 9.836 nS T R / TF Rise and Fall Times Measured between 0.8V and 2.0V 1.0 2.0 ns TLTJ Long-term Jitter 125-Ps period – 6.0 ns REF TDC REF Duty Cycle Measurement at 1.5V 45 55 % TPERIOD REF Period Measurement at 1.5V 69.827 69.855 ns T R / TF REF Rise and Fall Times Measured between 0.8V and 2.0V 1.0 4.0 V/ns TCCJ REF Cycle-to-Cycle Jitter Measurement at 1.5V – 1000 ps ENABLE/DISABLE and SET-UP TSTABLE Clock Stabilization from Power-up TSS Stopclock Set-up Time TSH Stopclock Hold Time Table 7. Group Timing Relationship and Tolerances Offset – 1.8 ms 10.0 – ns 0 – ns Table 9. Maximum Lumped Capacitive Output Loads Clock Max Load Unit Group Conditions Min. Max. PCI Clocks 30 pF 3V66 to PCI 3V66 Leads PCI 1.5 ns 3.5 ns 3V66 Clocks 30 pF Table 8. USB to DOT Phase Offset Parameter Typical Value Tolerance DOT Skew 0° 0.0ns 1000 ps USB Skew 180° 0.0ns 1000 ps VCH SKew 0° 0.0ns 1000 ps Rev 1.0, November 22, 2006 USB Clock 20 pF DOT Clock 10 pF REF Clock 30 pF Page 13 of 15 CY28419 Test and Measurement Set-up For Differential CPU and SRC Output Signals The following diagram shows lumped test load configurations for the differential Host Clock Outputs. M e a s u re m e n t P o in t TPCB : CPUT : M e a s u re m e n t P o in t TPCB : CPUC 2pF : IR E F 2pF : Figure 7. 0.7V Load Configuration O u tp u t u n d e r T e s t P ro b e Load Cap 3 .3 V s ig n a ls tD C - - 3 .3 V 2 .0 V 1 .5 V 0 .8 V 0V Tr Tf Figure 8. Lumped Load For Single-ended Output Signals (for AC Parameters Measurement) Table 10.CPU Clock Current Select Function Board Target Trace/Term Z Reference R, Iref – VDD (3*Rr) Output Current Voh @ Z 50 Ohms RREF = 475 1%, IREF = 2.32 mA Ioh = 6*Iref 0.7V @ 50 Ordering Information Part Number Package Type Product Flow CY28419OC 56-pin Shrunk Small Outline package (SSOP) Commercial, 0q to 70qC CY28419OCT 56-pin Shrunk Small Outline package (SSOP) – Tape and Reel Commercial, 0q to 70qC CY28419ZC 56-pin Thin Shrunk Small Outline package (TSSOP) Commercial, 0q to 70qC CY28419ZCT 56-pin Thin Shrunk Small Outline package (TSSOP) – Tape and Reel Commercial, 0q to 70qC Rev 1.0, November 22, 2006 Page 14 of 15 CY28419 Package Drawing and Dimensions 56-Lead Shrunk Small Outline Package O56 56-Lead Thin Shrunk Small Outline Package, Type II (6 mm x 14 mm) Z56 While SLI has reviewed all information herein for accuracy and reliability, Spectra Linear Inc. assumes no responsibility for the use of any circuitry or for the infringement of any patents or other rights of third parties which would result from each use. This product is intended for use in normal commercial applications and is not warranted nor is it intended for use in life support, critical medical instruments, or any other application requiring extended temperature range, high reliability, or any other extraordinary environmental requirements unless pursuant to additional processing by Spectra Linear Inc., and expressed written agreement by Spectra Linear Inc. Spectra Linear Inc. reserves the right to change any circuitry or specification without notice. Rev 1.0, November 22, 2006 Page 15 of 15