HOTTECH ES3G Super-fast rectifier Datasheet

Plastic-Encapsulate Diodes
SUPER-FAST RECTIFIER
ES3A --- ES3J
FEATURES
Glass Passivated Die Construction
Super-Fast Recovery Time For High Efficiency
Low Forward Voltage Drop and High Current
Capability
Surge Overload Rating to 100A Peak
Ideally Suited for Automated Assembly
Plastic Material: UL Flammability
Classification Rating 94V-0
10
0.245(6.22)
0.220(5.59)
0.125(3.17)
0.115(2.92)
0.280(7.11)
0.260(6.60)
0.012(0.305)
0.006(0.152)
0.103(2.62)
0.079(2.06)
MECHANICAL DATA
Case: Molded Plastic
Terminals: Solder Plated Terminal - Solderable
per MIL-STD-202, Method 208
Polarity: Cathode Band or Cathode Notch
Mounting Position: Any
Marking: Type Number
0.060(1.52)
0.030(0.76)
0.320(8.13)
0.305(7.75)
0.008(0.203)
0.004(0.102)
DO-214AB (SMC)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 OC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive
load. For capacitive load, derate current by 20%.
Notes:
1. Unit mounted on PC board with 5.0 mm2 (0.013 mm thick) copper pads as heat sink.
2. Measured at 1.0MHz and applied reverse voltage of 4.0V DC.
3. Measured with IF = 0.5A, IR = 1.0A, Irr = 0.25A. See Figure 5.
GUANGDONG HOTTECH
INDUSTRIAL CO,. LTD.
Page:P2-P1
Plastic-Encapsulate Diodes
ES3A --- ES3J
Typical Characteristics
IF, INSTANTANEOUS FORWARD CURRENT (A)
IO, AVERAGE RECTIFIED CURRENT (A)
3.0
2.0
1.0
0
25
75
50
100
125
150
10
1.0
0.1
Tj = 25°C
Pulse Width: 300µs
0.01
175
0
0.8
1.2
1.6
VF, INSTANTANEOUS FORWARD VOLTAGE (V)
Fig. 2 Typical Forward Characteristics
120
IR, INSTANTANEOUS REVERSE CURRENT (A)
IFSM, PEAK FORWARD SURGE CURRENT (A)
TT, TERMINAL TEMPERATURE (°C)
Fig. 1 Forward Current Derating Curve
0.4
Single Half-Sine-Wave
(JEDEC Method)
100
80
60
40
20
1000
Tj = 125°C
100
10
Tj = 25°C
1.0
0
1
10
0
100
NUMBER OF CYCLES AT 60Hz
Fig. 3 Surge Current Derating Curve
40
80
120
PERCENT OF RATED PEAK REVERSE VOLTAGE (%)
Fig. 4 Typical Reverse Characteristics
trr
+0.5A
50Ω NI (Non-inductive)
10Ω NI
Device
Under
Test
(-)
0A
(+)
Pulse
Generator
(Note 2)
50V DC
Approx
(-)
1.0Ω
NI
Oscilloscope
(Note 1)
-0.25A
(+)
Notes:
1. Rise Time = 7.0ns max. Input Impedance = 1.0MΩ, 22pF.
2. Rise Time = 10ns max. Input Impedance = 50Ω.
-1.0A
Set time base for 50/100 ns/cm
Fig. 5 Reverse Recovery Time Characteristic and Test Circuit
GUANGDONG HOTTECH
INDUSTRIAL CO,. LTD.
Page:P2-P2