a 800 MHz, 50 mW Current Feedback Amplifier AD8001 FEATURES Excellent Video Specifications (RL = 150 , G = +2) Gain Flatness 0.1 dB to 100 MHz 0.01% Differential Gain Error 0.025 Differential Phase Error Low Power 5.5 mA Max Power Supply Current (55 mW) High Speed and Fast Settling 880 MHz, –3 dB Bandwidth (G = +1) 440 MHz, –3 dB Bandwidth (G = +2) 1200 V/s Slew Rate 10 ns Settling Time to 0.1% Low Distortion –65 dBc THD, fC = 5 MHz 33 dBm Third Order Intercept, F1 = 10 MHz –66 dB SFDR, f = 5 MHz High Output Drive 70 mA Output Current Drives Up to 4 Back-Terminated Loads (75 Each) While Maintaining Good Differential Gain/Phase Performance (0.05%/0.25) APPLICATIONS A-to-D Drivers Video Line Drivers Professional Cameras Video Switchers Special Effects RF Receivers FUNCTIONAL BLOCK DIAGRAMS 8-Lead PDIP (N-8), CERDIP (Q-8) and SOIC (R-8) NC 1 8 –IN 2 7 V+ +IN 3 6 OUT 5 NC V– 4 5-Lead SOT-23-5 (RT-5) AD8001 NC VOUT 1 AD8001 5 +VS 4 –IN –VS 2 +IN 3 NC = NO CONNECT transimpedance linearization circuitry. This allows it to drive video loads with excellent differential gain and phase performance on only 50 mW of power. The AD8001 is a current feedback amplifier and features gain flatness of 0.1 dB to 100 MHz while offering differential gain and phase error of 0.01% and 0.025°. This makes the AD8001 ideal for professional video electronics such as cameras and video switchers. Additionally, the AD8001’s low distortion and fast settling make it ideal for buffer high speed A-to-D converters. The AD8001 offers low power of 5.5 mA max (VS = ± 5 V) and can run on a single +12 V power supply, while being capable of delivering over 70 mA of load current. These features make this amplifier ideal for portable and battery-powered applications where size and power are critical. GENERAL DESCRIPTION The AD8001 is a low power, high speed amplifier designed to operate on ± 5 V supplies. The AD8001 features unique The outstanding bandwidth of 800 MHz along with 1200 V/µs of slew rate make the AD8001 useful in many general-purpose high speed applications where dual power supplies of up to ± 6 V and single supplies from 6 V to 12 V are needed. The AD8001 is available in the industrial temperature range of –40°C to +85°C. 9 VS = 5V RFB = 820 6 GAIN – dB 3 G = +2 RL = 100 0 –3 VS = 5V RFB = 1k –6 –9 –12 10M 100M FREQUENCY – Hz 1G Figure 1. Frequency Response of AD8001 Figure 2. Transient Response of AD8001; 2 V Step, G = +2 REV. D Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective companies. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 © 2003 Analog Devices, Inc. All rights reserved. Powered by TCPDF (www.tcpdf.org) IMPORTANT LINKS for the AD8001* Last content update 08/18/2013 12:37 am PARAMETRIC SELECTION TABLES DESIGN TOOLS, MODELS, DRIVERS & SOFTWARE Find Similar Products By Operating Parameters High Speed Amplifiers Selection Table Analog Filter Wizard 2.0 AD8001A SPICE Macro Model AD8001AN SPICE Macro Model AD8001AR SPICE Macro Model DOCUMENTATION AD8001: Military Data Sheet AN-692: Universal Precision Op Amp Evaluation Board AN-649: Using the Analog Devices Active Filter Design Tool AN-358: Noise and Operational Amplifier Circuits AN-356: User’s Guide to Applying and Measuring Operational Amplifier Specifications AN-417: Fast Rail-to-Rail Operational Amplifiers Ease Design Constraints in Low Voltage High Speed Systems AN-257: Careful Design Tames High Speed Op Amps AN-253: Find Op Amp Noise with Spreadsheet MT-057: High Speed Current Feedback Op Amps MT-051: Current Feedback Op Amp Noise Considerations MT-034: Current Feedback (CFB) Op Amps MT-059: Compensating for the Effects of Input Capacitance on VFB and CFB Op Amps Used in Current-to-Voltage Converters A Stress-Free Method for Choosing High-Speed Op Amps UG-127: Universal Evaluation Board for High Speed Op Amps in SOT-23-5/SOT-23-6 Packages UG-101: Evaluation Board User Guide ADI Warns Against Misuse of COTS Integrated Circuits Two-Stage Current-Feedback Amplifier Choosing High-Speed Signal Processing Components for Ultrasound Systems Current Feedback Amplifiers Part 1: Ask The Applications Engineer-22 Current Feedback Amplifiers Part 2: Ask The Applications Engineer-23 PCN#00-406 Aerospace Dice Standard Space Level Products Program Space Qualified Parts List DESIGN COLLABORATION COMMUNITY Collaborate Online with the ADI support team and other designers about select ADI products. Follow us on Twitter: www.twitter.com/ADI_News Like us on Facebook: www.facebook.com/AnalogDevicesInc DESIGN SUPPORT Submit your support request here: Linear and Data Converters Embedded Processing and DSP Telephone our Customer Interaction Centers toll free: Americas: Europe: China: India: Russia: 1-800-262-5643 00800-266-822-82 4006-100-006 1800-419-0108 8-800-555-45-90 Quality and Reliability Lead(Pb)-Free Data SAMPLE & BUY AD8001 View Price & Packaging Request Evaluation Board Request Samples Check Inventory & Purchase Find Local Distributors EVALUATION KITS & SYMBOLS & FOOTPRINTS View the Evaluation Boards and Kits page for documentation and purchasing Symbols and Footprints * This page was dynamically generated by Analog Devices, Inc. and inserted into this data sheet. Note: Dynamic changes to the content on this page (labeled 'Important Links') does not constitute a change to the revision number of the product data sheet. This content may be frequently modified. AD8001–SPECIFICATIONS (@ T = + 25C, V = 5 V, R = 100 , unless otherwise noted.) A Model DYNAMIC PERFORMANCE –3 dB Small Signal Bandwidth, N Package R Package RT Package S L AD8001A Typ Max Conditions Min Unit G = +2, < 0.1 dB Peaking, R F = 750 Ω G = +1, < 1 dB Peaking, RF = 1 kΩ G = +2, < 0.1 dB Peaking, R F = 681 Ω G = +1, < 0.1 dB Peaking, R F = 845 Ω G = +2, < 0.1 dB Peaking, R F = 768 Ω G = +1, < 0.1 dB Peaking, RF = 1 kΩ 350 650 350 575 300 575 440 880 440 715 380 795 MHz MHz MHz MHz MHz MHz G = +2, R F = 750 Ω G = +2, R F = 681 Ω G = +2, R F = 768 Ω G = +2, VO = 2 V Step G = –1, VO = 2 V Step G = –1, VO = 2 V Step G = +2, VO = 2 V Step, RF = 649 Ω 85 100 120 800 960 110 125 145 1000 1200 10 1.4 MHz MHz MHz V/µs V/µs ns ns –65 dBc 2.0 2.0 18 0.01 0.025 33 14 –66 nV/√Hz pA/√Hz pA/√Hz % Degree dBm dBm dB Bandwidth for 0.1 dB Flatness N Package R Package RT Package Slew Rate Settling Time to 0.1% Rise and Fall Time NOISE/HARMONIC PERFORMANCE Total Harmonic Distortion Input Voltage Noise Input Current Noise Differential Gain Error Differential Phase Error Third Order Intercept 1 dB Gain Compression SFDR fC = 5 MHz, VO = 2 V p-p G = +2, RL = 100 Ω f = 10 kHz f = 10 kHz, +In –In NTSC, G = +2, R L = 150 Ω NTSC, G = +2, R L = 150 Ω f = 10 MHz f = 10 MHz f = 5 MHz DC PERFORMANCE Input Offset Voltage 2.0 2.0 10 5.0 TMIN –TMAX Offset Drift –Input Bias Current TMIN –TMAX +Input Bias Current Open-Loop Transresistance INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio Offset Voltage –Input Current +Input Current OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Short Circuit Current POWER SUPPLY Operating Range Quiescent Current Power Supply Rejection Ratio –Input Current +Input Current 3.0 TMIN –TMAX VO = ± 2.5 V TMIN –TMAX 250 175 +Input –Input +Input 0.025 0.04 5.5 9.0 25 35 6.0 10 900 10 50 1.5 3.2 VCM = ± 2.5 V VCM = ± 2.5 V, TMIN –TMAX VCM = ± 2.5 V, TMIN –TMAX 50 R L = 150 Ω R L = 37.5 Ω 2.7 50 85 54 0.3 0.2 60 50 MΩ Ω pF ±V 1.0 0.7 5.0 75 56 0.5 0.1 dB µA/V µA/V ±V mA mA 3.1 70 110 ± 3.0 TMIN –TMAX +VS = +4 V to +6 V, –VS = –5 V –VS = – 4 V to – 6 V, +VS = +5 V TMIN –TMAX TMIN –TMAX mV mV µV/°C ±µA ±µA ±µA ±µA kΩ kΩ ± 6.0 5.5 2.5 0.5 V mA dB dB µA/V µA/V Specifications subject to change without notice. –2– REV. D AD8001 ABSOLUTE MAXIMUM RATINGS 1 MAXIMUM POWER DISSIPATION Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 V Internal Power Dissipation @ 25°C2 PDIP Package (N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 W SOIC (R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8 W 8-Lead CERDIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 W SOT-23-5 Package (RT) . . . . . . . . . . . . . . . . . . . . . . . 0.5 W Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ± VS Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ± 1.2 V Output Short Circuit Duration . . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves Storage Temperature Range N, R . . . . . . . . . –65°C to +125°C Operating Temperature Range (A Grade) . . . –40°C to +85°C Lead Temperature Range (Soldering 10 sec) . . . . . . . . . 300°C The maximum power that can be safely dissipated by the AD8001 is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately 150°C. Exceeding this limit temporarily may cause a shift in parametric performance due to a change in the stresses exerted on the die by the package. Exceeding a junction temperature of 175°C for an extended period can result in device failure. 2.0 MAXIMUM POWER DISSIPATION – W NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 Specification is for device in free air: 8-Lead PDIP Package: θJA = 90°C/W 8-Lead SOIC Package: θJA = 155°C/W 8-Lead CERDIP Package: θJA = 110°C/W 5-Lead SOT-23-5 Package: θJA = 260°C/W While the AD8001 is internally short circuit protected, this may not be sufficient to guarantee that the maximum junction temperature (150°C) is not exceeded under all conditions. To ensure proper operation, it is necessary to observe the maximum power derating curves. 8-LEAD PDIP PACKAGE TJ = +150C 8-LEAD CERDIP PACKAGE 1.5 8-LEAD SOIC PACKAGE 1.0 0.5 5-LEAD SOT-23-5 PACKAGE 0 –50 –40 –30 –20 –10 0 10 20 30 40 50 60 AMBIENT TEMPERATURE – C 70 80 90 Figure 3. Plot of Maximum Power Dissipation vs. Temperature ORDERING GUIDE Model Temperature Range Package Description Package Option Branding AD8001AN AD8001AQ AD8001AR AD8001AR-REEL AD8001AR-REEL7 AD8001ART-REEL AD8001ART-REEL7 AD8001ACHIPS 5962-9459301MPA* –40°C to +85°C –55°C to +125°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –40°C to +85°C –55°C to +125°C 8-Lead PDIP 8-Lead CERDIP 8-Lead SOIC 13" Tape and REEL 7" Tape and REEL 13" Tape and REEL 7" Tape and REEL Die Form 8-Lead CERDIP N-8 Q-8 R-8 R-8 R-8 RT-5 RT-5 HEA HEA * Q-8 Standard Military Drawing Device. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8001 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. D –3– WARNING! ESD SENSITIVE DEVICE AD8001–Typical Performance Characteristics 806 0.001F +VS VOUT TO TEKTRONIX CSA 404 COMM. SIGNAL ANALYZER 0.1F 806 AD8001 0.1F VIN HP8133A PULSE GENERATOR 50 RL = 100 0.001F TR/TF = 50ps –VS 400mV 5ns TPC 4. 2 V Step Response, G = +2 TPC 1. Test Circuit , Gain = +2 909 0.001F +VS 0.1F VOUT TO TEKTRONIX CSA 404 COMM. SIGNAL ANALYZER AD8001 0.1F VIN LeCROY 9210 PULSE GENERATOR TR/TF = 350ps TPC 2. 1 V Step Response, G = +2 0.5V 50 RL = 100 0.001F –VS TPC 5. Test Circuit, Gain = +1 5ns TPC 3. 2 V Step Response, G = +1 TPC 6. 100 mV Step Response, G = +1 –4– REV. D AD8001 1000 9 VS = 5V RFB = 820 G = +2 RL = 100 GAIN – dB 3 0 VS = 5V RFB = 1k –3 VS = 5V RL = 100 G = +2 800 –3dB BANDWIDTH – MHz 6 –6 600 N PACKAGE 400 R PACKAGE 200 –9 –12 10M 100M FREQUENCY – Hz 0 500 1G TPC 7. Frequency Response, G = +2 0.1 0 HARMONIC DISTORTION – dBc OUTPUT – dB –0.5 900 1000 5V SUPPLIES RF = 750 –0.3 –0.4 800 –50 RF = 698 –0.2 700 TPC 10. –3 dB Bandwidth vs. RF RF = 649 –0.1 600 VALUE OF FEEDBACK RESISTOR (RF) – G = +2 RL = 100 VIN = 50mV –0.6 –0.7 –60 VOUT = 2V p-p RL = 100 G = +2 –70 SECOND HARMONIC –80 THIRD HARMONIC –90 –0.8 –0.9 1M 10M FREQUENCY – Hz –100 10k 100M DIFF PHASE – Degrees –50 5V SUPPLIES VOUT = 2V p-p RL = 1k G = +2 –70 SECOND HARMONIC 10M 100M 0.08 0.06 G = +2 RF = 806 2 BACK TERMINATED LOADS (75) 0.04 0.02 0.00 1 BACK TERMINATED LOAD (150) –80 0.02 –90 DIFF GAIN – % HARMONIC DISTORTION – dBc 1M FREQUENCY – Hz TPC 11. Distortion vs. Frequency, RL = 100 Ω TPC 8. 0.1 dB Flatness, R Package (for N Package Add 50 Ω to RF) –60 100k THIRD HARMONIC –100 –110 10k 0.00 –0.01 –0.02 100k 1M FREQUENCY – Hz 10M 0 100M IRE 100 TPC 12. Differential Gain and Differential Phase TPC 9. Distortion vs. Frequency, RL = 1 kΩ REV. D 1 AND 2 BACK TERMINATED LOADS (150 AND 75) 0.01 –5– AD8001 5 1000 0 N PACKAGE 900 VIN = –26dBm –10 GAIN – dB –3dB BANDWIDTH – MHz –5 RF = 909 –15 –20 –25 800 R PACKAGE 700 VIN = 50mV RL = 100 G = +1 600 –30 –35 100M 1G 500 600 3G FREQUENCY – Hz TPC 13. Frequency Response, G = +1 –40 0 RF = 649 –50 –1 DISTORTION – dBc RF = 953 –2 OUTPUT – dB 1100 TPC 16. –3 dB Bandwidth vs. RF, G = +1 1 –3 –4 –5 900 700 800 1000 VALUE OF FEEDBACK RESISTOR (RF) – G = +1 RL = 100 VIN = 50mV –6 RL = 100 G = +1 VOUT = 2V p-p –60 SECOND HARMONIC –70 –80 THIRD HARMONIC –7 –90 –8 –9 2M 10M 100M FREQUENCY – Hz –100 10k 1G 100M 0 G = +1 RL = 1k VOUT = 2V p-p –3 –60 –6 OUTPUT – dBV DISTORTION – dBc 10M 3 –40 –70 SECOND HARMONIC –80 THIRD HARMONIC –90 –9 –12 –15 –18 –21 –100 –110 10k 1M FREQUENCY – Hz TPC 17. Distortion vs. Frequency, RL = 100 Ω TPC 14. Flatness, R Package, G = +1 (for N Package Add 100 Ω to RF) –50 100k RL = 100 G = +1 –24 100k 1M FREQUENCY – Hz 10M –27 1M 100M TPC 15. Distortion vs. Frequency, RL = 1 kΩ 10M FREQUENCY – Hz 100M TPC 18. Large Signal Frequency Response, G = +1 –6– REV. D AD8001 45 2.2 40 2.0 30 INPUT OFFSET VOLTAGE – mV G = +100 35 RF = 1000 25 GAIN – dB 20 G = +10 15 RF = 470 10 5 0 –5 RL = 100 –10 –15 1.8 1.6 DEVICE NO. 2 1.4 1.2 1.0 DEVICE NO. 3 0.8 0.6 –20 –25 DEVICE NO. 1 1M 10M 100M FREQUENCY – Hz 0.4 –60 1G 3.35 5.8 3.25 5.6 3.15 +VOUT RL = 150 VS = 5V 3.05 | –VOUT | 2.95 2.85 +VOUT RL = 50 VS = 5V 2.75 2.55 –60 –40 –20 0 20 40 60 JUNCTION TEMPERATURE – C 80 VS = 5V 5.0 4.8 5 125 4 120 SHORT CIRCUIT CURRENT – mA INPUT BIAS CURRENT – A 5.2 –40 –20 0 20 40 60 80 100 JUNCTION TEMPERATURE – C 120 140 TPC 23. Supply Current vs. Temperature 3 –IN 2 1 0 –1 +IN –2 SOURCE ISC 115 110 | SINK ISC | 105 100 95 90 –3 –40 –20 0 20 40 60 80 100 120 85 –60 140 JUNCTION TEMPERATURE – C –40 –20 0 20 40 60 JUNCTION TEMPERATURE – C 80 100 TPC 24. Short Circuit Current vs. Temperature TPC 21. Input Bias Current vs. Temperature REV. D 100 5.4 4.4 –60 100 TPC 20. Output Swing vs. Temperature –4 –60 80 4.6 | –VOUT | 2.65 –20 0 20 40 60 JUNCTION TEMPERATURE – C TPC 22. Input Offset vs. Temperature SUPPLY CURRENT – mA OUTPUT SWING – Volts TPC 19. Frequency Response, G = +10, G = +100 –40 –7– AD8001 6 1k 100 VS = 5V RL = 150 VOUT = 2.5V 4 ROUT – TRANSRESISTANCE – k 5 3 –TZ 2 1 0 –60 1 G = +2 RF = 909 0.1 +TZ –40 10 –20 0 20 40 60 80 100 JUNCTION TEMPERATURE – C 120 0.01 10k 140 TPC 25. Transresistance vs. Temperature 100 100k 1M FREQUENCY – Hz 10M TPC 28. Output Resistance vs. Frequency 100 1 RF = 576 0 –1 10 10 NONINVERTING CURRENT VS = 5V RF = 649 –2 OUTPUT – dB INVERTING CURRENT VS = 5V NOISE CURRENT – pA/√Hz NOISE VOLTAGE – nV/√Hz 100M –3 –4 G = –1 RL = 100 VIN = 50mV RF = 750 –5 –6 –7 –8 VOLTAGE NOISE VS = 5V 1 10 100 1k FREQUENCY – Hz 1 100k 10k –9 1M 10M 100M FREQUENCY – Hz 1G TPC 29. –3 dB Bandwidth vs. Frequency, G = –1 TPC 26. Noise vs. Frequency –48 –52.5 –55.0 –49 –CMRR –PSRR –57.5 –50 PSRR – dB CMRR – dB –60.0 –51 +CMRR –52 –53 2.5V SPAN 3V SPAN –62.5 CURVES ARE FOR WORSTCASE CONDITION WHERE ONE SUPPLY IS VARIED WHILE THE OTHER IS HELD CONSTANT. –65.0 –67.5 –70.0 –54 –72.5 +PSRR –55 –56 –60 –75.0 –40 –20 0 20 40 60 80 100 JUNCTION TEMPERATURE – C 120 –77.5 –60 140 TPC 27. CMRR vs. Temperature –40 –20 0 20 40 60 JUNCTION TEMPERATURE – C 80 100 TPC 30. PSRR vs. Temperature –8– REV. D AD8001 30 –10 10 51 150 –20 VOUT 62 0 150 PSRR – dB CMRR – dB 910 CURVES ARE FOR WORSTCASE CONDITION WHERE ONE SUPPLY IS VARIED WHILE THE OTHER IS HELD CONSTANT. 20 910 VIN –30 –10 –PSRR –20 –30 –40 +PSRR –PSRR +PSRR –40 RF = 909 G = +2 –50 –50 –60 300k 1M 10M FREQUENCY – Hz 100M 1M 1G TPC 31. CMRR vs. Frequency 1G 10M 100M FREQUENCY – Hz TPC 34. PSRR vs. Frequency 1 RF = 549 0 –1 RF = 649 OUTPUT – dB –2 –3 G = –2 RL = 100 VIN = 50mVrms –4 –5 RF = 750 –6 –7 –8 10M 100M FREQUENCY – Hz 1G TPC 35. 2 V Step Response, G = –1 TPC 32. –3 dB Bandwidth vs. Frequency, G = –2 100 100 3 WAFER LOTS COUNT = 895 MEAN = 1.37 STD DEV = 1.13 MIN = –2.45 MAX = +4.69 90 80 70 90 80 CUMULATIVE 70 COUNT 60 50 FREQ DIST 40 40 30 30 20 20 10 10 0 –5 –4 –3 –2 –1 0 1 2 3 INPUT OFFSET VOLTAGE – mV 4 5 TPC 36. Input Offset Voltage Distribution TPC 33. 100 mV Step Response, G = –1 REV. D 60 50 –9– 0 PERCENT –9 1M AD8001 THEORY OF OPERATION A very simple analysis can put the operation of the AD8001, a current feedback amplifier, in familiar terms. Being a current feedback amplifier, the AD8001’s open-loop behavior is expressed as transimpedance, ∆VO/∆I–IN, or TZ. The open-loop transimpedance behaves just as the open-loop voltage gain of a voltage feedback amplifier, that is, it has a large dc value and decreases at roughly 6 dB/octave in frequency. Since the RIN is proportional to 1/gM, the equivalent voltage gain is just TZ × gM, where the gM in question is the transconductance of the input stage. This results in a low open-loop input impedance at the inverting input, a now familiar result. Using this amplifier as a follower with gain, Figure 4, basic analysis yields the following result. Considering that additional poles contribute excess phase at high frequencies, there is a minimum feedback resistance below which peaking or oscillation may result. This fact is used to determine the optimum feedback resistance, R F. In practice, parasitic capacitance at Pin 2 will also add phase in the feedback loop, so picking an optimum value for R F can be difficult. Figure 6 illustrates this problem. Here the fine scale (0.1 dB/ div) flatness is plotted versus feedback resistance. These plots were taken using an evaluation card which is available to customers so that these results may readily be duplicated. Achieving and maintaining gain flatness of better than 0.1 dB at frequencies above 10 MHz requires careful consideration of several issues. 0.1 TZ (S ) VO =G× VIN TZ (S ) + G × RIN + R1 R1 R2 RF = 698 –0.1 RIN = 1 / g M ≈ 50 Ω –0.2 OUTPUT – dB G = 1+ RF = 649 0 R1 G = +2 –0.3 RF = 750 –0.4 –0.5 R2 –0.6 RIN –0.7 VOUT –0.8 VIN –0.9 1M 10M FREQUENCY – Hz 100M Figure 6. 0.1 dB Flatness vs. Frequency Figure 4. Follower with Gain Recognizing that G × RIN << R1 for low gains, it can be seen to the first order that bandwidth for this amplifier is independent of gain (G). This simple analysis in conjunction with Figure 5 can, in fact, predict the behavior of the AD8001 over a wide range of conditions. 1M 100k Choice of Feedback and Gain Resistors Because of the above-mentioned relationship between the bandwidth and feedback resistor, the fine scale gain flatness will, to some extent, vary with feedback resistance. It, therefore, is recommended that once optimum resistor values have been determined, 1% tolerance values should be used if it is desired to maintain flatness over a wide range of production lots. In addition, resistors of different construction have different associated parasitic capacitance and inductance. Surface-mount resistors were used for the bulk of the characterization for this data sheet. It is not recommended that leaded components be used with the AD8001. TZ – 10k 1k 100 10 100k 1M 10M FREQUENCY – Hz 100M 1G Figure 5. Transimpedance vs. Frequency –10– REV. D AD8001 Printed Circuit Board Layout Considerations Driving Capacitive Loads As to be expected for a wideband amplifier, PC board parasitics can affect the overall closed-loop performance. Of concern are stray capacitances at the output and the inverting input nodes. If a ground plane is to be used on the same side of the board as the signal traces, a space (5 mm min) should be left around the signal lines to minimize coupling. Additionally, signal lines connecting the feedback and gain resistors should be short enough so that their associated inductance does not cause high frequency gain errors. Line lengths on the order of less than 5 mm are recommended. If long runs of coaxial cable are being driven, dispersion and loss must be considered. The AD8001 was designed primarily to drive nonreactive loads. If driving loads with a capacitive component is desired, best frequency response is obtained by the addition of a small series resistance, as shown in Figure 8. The accompanying graph shows the optimum value for RSERIES versus capacitive load. It is worth noting that the frequency response of the circuit when driving large capacitive loads will be dominated by the passive roll-off of RSERIES and CL. 909 Power Supply Bypassing RSERIES Adequate power supply bypassing can be critical when optimizing the performance of a high frequency circuit. Inductance in the power supply leads can form resonant circuits that produce peaking in the amplifier’s response. In addition, if large current transients must be delivered to the load, then bypass capacitors (typically greater than 1 µF) will be required to provide the best settling time and lowest distortion. A parallel combination of 4.7 µF and 0.1 µF is recommended. Some brands of electrolytic capacitors will require a small series damping resistor ≈4.7 Ω for optimum results. IN RL 500 CL Figure 8. Driving Capacitive Loads 40 G = +1 DC Errors and Noise R R VOUT = VIO × 1 + F ± I BN × RN × 1 + F ± I BI × RF RI RI RF RI RN IBI IBN VOUT Figure 7. Output Offset Voltage REV. D –11– 30 RSERIES – There are three major noise and offset terms to consider in a current feedback amplifier. For offset errors, refer to the equation below. For noise error the terms are root-sum-squared to give a net output error. In the circuit in Figure 7 they are input offset (VIO), which appears at the output multiplied by the noise gain of the circuit (1 + RF/RI), noninverting input current (IBN × RN) also multiplied by the noise gain, and the inverting input current, which when divided between RF and RI and subsequently multiplied by the noise gain always appears at the output as IBN × RF. The input voltage noise of the AD8001 is a low 2 nV/ √Hz. At low gains though the inverting input current noise times RF is the dominant noise source. Careful layout and device matching contribute to better offset and drift specifications for the AD8001 compared to many other current feedback amplifiers. The typical performance curves in conjunction with the following equations can be used to predict the performance of the AD8001 in any application. 20 10 0 0 5 10 15 20 25 CL – pF Figure 9. Recommended RSERIES vs. Capacitive Load AD8001 Communications Operation as a Video Line Driver Distortion is a key specification in communications applications. Intermodulation distortion (IMD) is a measure of the ability of an amplifier to pass complex signals without the generation of spurious harmonics. The third order products are usually the most problematic since several of them fall near the fundamentals and do not lend themselves to filtering. Theory predicts that the third order harmonic distortion components increase in power at three times the rate of the fundamental tones. The specification of third order intercept as the virtual point where fundamental and harmonic power are equal is one standard measure of distortion performance. Op amps used in closed-loop applications do not always obey this simple theory. At a gain of +2, the AD8001 has performance summarized in Figure 10. Here the worst third order products are plotted versus input power. The third order intercept of the AD8001 is +33 dBm at 10 MHz. The AD8001 has been designed to offer outstanding performance as a video line driver. The important specifications of differential gain (0.01%) and differential phase (0.025°) meet the most exacting HDTV demands for driving one video load. The AD8001 also drives up to two back terminated loads as shown in Figure 11, with equally impressive performance (0.01%, 0.07°). Another important consideration is isolation between loads in a multiple load application. The AD8001 has more than 40 dB of isolation at 5 MHz when driving two 75 Ω back terminated loads. 909 75 75 CABLE 909 +VS VOUT NO. 1 75 0.001F + 0.1F –45 THIRD ORDER IMD – dBc –50 G = +2 F1 = 10MHz 75 CABLE F2 = 12MHz AD8001 VIN 2F2 – F1 –55 75 75 CABLE 0.1F VOUT NO. 2 75 75 –60 0.001F 2F1 – F2 –65 –VS Figure 11. Video Line Driver –70 –75 –80 –8 –7 –6 –5 –4 –3 –2 –1 0 1 INPUT POWER – dBm 2 3 4 5 6 Figure 10. Third Order IMD; F1 = 10 MHz, F2 = 12 MHz –12– REV. D AD8001 ADC. Using the AD9058’s internal +2 V reference connected to both ADCs as shown in Figure 12 reduces the number of external components required to create a complete data acquisition system. The 20 Ω resistors in series with ADC inputs are used to help the AD8001s drive the 10 pF ADC input capacitance. The AD8001 only adds 100 mW to the power consumption while not limiting the performance of the circuit. Driving A-to-D Converters The AD8001 is well suited for driving high speed analog-todigital converters such as the AD9058. The AD9058 is a dual 8-bit 50 MSPS ADC. In the circuit below, the AD8001 is shown driving the inputs of the AD9058, which are configured for 0 V to 2 V ranges. Bipolar input signals are buffered, amplified (–2×), and offset (by +1.0 V) into the proper input range of the 1k ENCODE 74ACT04 10 ENCODE A 8 649 38 ANALOG IN A 0.5V 324 10pF 50 36 ENCODE B –VREF A +VS –VREF B 5, 9, 22, 24, 37, 41 AD9058 20 AD8001 6 RZ1 (J-LEAD) AIN A 1.3k +5V 0.1F D0A (LSB) 18 17 AD707 0.1F 20k 20k 3 0.1F 43 15 +VINT 14 +VREF A 13 +VREF B 12 D7A (MSB) 1.3k 649 D0B (LSB) 324 28 RZ2 29 30 20 AD8001 40 31 AIN B 32 33 1 D7B (MSB) –VS RZ1, RZ2 = 2,000 SIP (8-PKG) 35 7, 20, 26, 39 0.1F 4,19, 21 25, 27, 42 Figure 12. AD8001 Driving a Dual A-to-D Converter REV. D –13– 8 34 COMP 0.1F 8 11 74ACT 273 ANALOG IN B 0.5V 74ACT 273 16 2 –2V –5V 1N4001 CLOCK AD8001 (4.7 µF–10 µF) tantalum electrolytic capacitor should be connected in parallel, but not necessarily so close, to supply current for fast, large-signal changes at the output. Layout Considerations The specified high speed performance of the AD8001 requires careful attention to board layout and component selection. Proper RF design techniques and low parasitic component selection are mandatory. The feedback resistor should be located close to the inverting input pin in order to keep the stray capacitance at this node to a minimum. Capacitance variations of less than 1 pF at the inverting input will significantly affect high speed performance. The PCB should have a ground plane covering all unused portions of the component side of the board to provide a low impedance ground path. The ground plane should be removed from the area near the input pins to reduce stray capacitance. Stripline design techniques should be used for long signal traces (greater than about 1 inch). These should be designed with a characteristic impedance of 50 Ω or 75 Ω and be properly terminated at each end. Chip capacitors should be used for supply bypassing (see Figure 13). One end should be connected to the ground plane and the other within 1/8 inch of each power pin. An additional large RF RF +VS +VS +VS C1 0.1F RG IN RO RT RG C3 10F RO OUT OUT C2 0.1F RS –VS IN C4 10F RT –VS Inverting Configuration Supply Bypassing –VS Noninverting Configuration Figure 13. Inverting and Noninverting Configurations for Evaluation Boards Table I. Recommended Component Values AD8001AN (PDIP) Gain AD8001AR (SOIC) Gain AD8001ART (SOT-23-5) Gain Component –1 +1 +2 +10 +100 –1 +1 +2 +10 +100 –1 +1 RF (Ω) RG (Ω) RO (Nominal) (Ω) RS (Ω) RT (Nominal) (Ω) Small Signal BW (MHz) 0.1 dB Flatness (MHz) 649 649 49.9 0 54.9 340 1050 470 51 49.9 1000 10 49.9 49.9 681 681 49.9 470 51 49.9 1000 10 49.9 49.9 880 49.9 460 49.9 260 49.9 20 604 604 49.9 0 54.9 370 953 49.9 750 750 49.9 49.9 710 49.9 440 49.9 260 49.9 20 845 845 49.9 0 54.9 240 70 105 130 100 120 110 105 –14– +2 +10 +100 1000 768 768 49.9 49.9 470 51 49.9 1000 10 49.9 49.9 795 49.9 380 49.9 260 49.9 20 300 145 REV. D AD8001 OUTLINE DIMENSIONS 8-Lead Plastic Dual In-Line Package [PDIP] (N-8) 8-Lead Ceramic Dual In-Line Package [CERDIP] (Q-8) Dimensions shown in inches and (millimeters) Dimensions shown in inches and (millimeters) 0.375 (9.53) 0.365 (9.27) 0.355 (9.02) 0.005 (0.13) MIN 0.055 (1.40) MAX 8 8 5 0.295 (7.49) 0.285 (7.24) 0.275 (6.98) 4 1 1 0.100 (2.54) BSC 0.015 (0.38) MIN 0.150 (3.81) 0.130 (3.30) 0.110 (2.79) 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.310 (7.87) 0.220 (5.59) PIN 1 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.180 (4.57) MAX 5 0.100 (2.54) BSC 0.150 (3.81) 0.135 (3.43) 0.120 (3.05) 0.320 (8.13) 0.290 (7.37) 0.405 (10.29) MAX 0.060 (1.52) 0.015 (0.38) 0.200 (5.08) MAX 0.150 (3.81) MIN 0.200 (5.08) 0.125 (3.18) 0.015 (0.38) 0.010 (0.25) 0.008 (0.20) SEATING PLANE 0.060 (1.52) 0.050 (1.27) 0.045 (1.14) 4 SEATING 0.070 (1.78) PLANE 0.030 (0.76) 0.023 (0.58) 0.014 (0.36) 0.015 (0.38) 0.008 (0.20) 15 0 CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN COMPLIANT TO JEDEC STANDARDS MO-095AA CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 8-Lead Standard Small Outline Package [SOIC] (R-8) 5-Lead Small Outline Transistor Package [SOT-23] (RT-5) Dimensions shown in millimeters and (inches) Dimensions shown in millimeters 5.00 (0.1968) 4.80 (0.1890) 4.00 (0.1574) 3.80 (0.1497) 8 5 1 4 2.90 BSC 5 6.20 (0.2440) 5.80 (0.2284) 2.80 BSC 1.60 BSC 1 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) COPLANARITY SEATING 0.10 PLANE 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) 0.31 (0.0122) 4 0.50 (0.0196) ⴛ 45ⴗ 0.25 (0.0099) 2 3 PIN 1 0.95 BSC 1.30 1.15 0.90 8ⴗ 0.25 (0.0098) 0ⴗ 1.27 (0.0500) 0.40 (0.0157) 0.17 (0.0067) 1.90 BSC 1.45 MAX COMPLIANT TO JEDEC STANDARDS MS-012AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 0.15 MAX 0.50 0.30 SEATING PLANE 0.22 0.08 10ⴗ 5ⴗ 0ⴗ COMPLIANT TO JEDEC STANDARDS MO-178AA REV. D –15– 0.60 0.45 0.30 AD8001 Location Page 7/03—Data Sheet changed from REV. C to REV. D Renumbered figures and TPCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Universal Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 –16– REV. D C01043–0–7/03(D) Revision History