Marketing Bulletin DATE: June 23rd, 2006 TO: All Sales Personnel FROM: Mark Stoner RE: Product Termination To all concerned parties, This bulletin is to notify all customers of the discontinuation of the following Ecliptek series effective July 1st, 2006: Series EC3SM1 EC4SM1 Description Four pad SMD Crystal Four pad SMD Crystal Recommended Replacement EC3SM EC4SM In compliance with our End of Life (EOL) policy, this will serve as advanced notice of product termination. New orders will not be accepted after September 31st, 2006, with delivery to conclude by December 31st 2006. If there are any questions pertaining to this bulletin, please fell free to contact me. Thank you again for your cooperation. Best Regards, Mark W. Stoner Vice President of Marketing Ecliptek Corporation 3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234 EC3SM1 Series EC3SM1 • Four pad surface mount package • AT or BT cut available • Resistance weld seal • Tight tolerance/stability • Interchangeable with plastic surface mount crystals • Tape and reel available NOTES H 5.18 L 12.50 W 4.95 CRYSTAL __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ OBSOLETE __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ELECTRICAL SPECIFICATIONS Frequency Range 4.000MHz, 7.3728MHz, 20.000MHz, and 30.000MHz Frequency Tolerance / Stability ±50ppm / ±100ppm (Standard), ±30ppm / ±50ppm (AT cut only), ±15ppm / ±30ppm (AT cut only), Over Operating Temperature Range or ±15ppm / ±20ppm (AT cut only) Operating Temperature Range 0°C to 70°C (Standard), -20°C to 70°C (AT cut only), or -40°C to 85°C (AT cut only) Aging (at 25°C) ±5ppm / year Maximum Storage Temperature Range -40°C to 85°C Shunt Capacitance 7pF Maximum Insulation Resistance 500 Megaohms Minimum at 100VDC Drive Level 1 mWatt Maximum Load Capacitance (CL) 18pF (Standard), Custom CL ≥10pF, or Series Resonant EQUIVALENT SERIES RESISTANCE (ESR), MODE OF OPERATION (MODE), AND CUT Nominal Frequency ESR (Ω) Mode / Cut Nominal Frequency ESR (Ω) Mode / Cut 4.000MHz 200 Max Fundamental / AT 30.000MHz 40 Max Fundamental / AT 7.3728MHz 120 Max Fundamental / AT 30.000MHz 40 Max Fundamental / BT 20.000MHz 50 Max Fundamental / AT MANUFACTURER CATEGORY SERIES PACKAGE CLASS REV.DATE ECLIPTEK CORP. CRYSTAL EC3SM1 EPOXY BASE CR34 06/06 800-ECLIPTEK www.ecliptek.com for latest revision Specifications subject to change without notice. PART NUMBERING GUIDE EC3SM1 - B - 20 - 30.000M TR PACKAGING OPTIONS Blank=Bulk, TR=Tape and Reel FREQUENCY TOLERANCE / STABILITY Blank=±50ppm at 25°C, ±100ppm from 0°C to 70°C A=±50ppm at 25°C, ±100ppm from -20°C to 70°C B=±50ppm at 25°C, ±100ppm from -40°C to 85°C C=±30ppm at 25°C, ±50ppm from 0°C to 70°C D=±30ppm at 25°C, ±50ppm from -20°C to 70°C E=±30ppm at 25°C, ±50ppm from -40°C to 85°C F=±15ppm at 25°C, ±30ppm from 0°C to 70°C G=±15ppm at 25°C, ±30ppm from -20°C to 70°C J=±15ppm at 25°C, ±20ppm from 0°C to 70°C FREQUENCY LOAD CAPACITANCE Blank=18pF (Standard), S=Series XX=XXpF (Custom) MODE OF OPERATION / CRYSTAL CUT Blank=Fundamental / AT B=Fundamental / BT OBSOLETE MECHANICAL DIMENSIONS SUGGESTED SOLDER PAD LAYOUT ALL DIMENSIONS IN MILLIMETERS ALL DIMENSIONS IN MILLIMETERS Coplanarity: 0.152 Maximum Tolerances = ±0.2 TAPE AND REEL DIMENSIONS ALL DIMENSIONS IN MILLIMETERS A B C D E 24±.3 11.5±.1 10.75±.1 4±.1 2±.1 TAPE REEL M N O P Q 1.5 MIN 50 MIN 20.2 MIN 13±.2 40 MIN QTY/REEL 1,000 F G H J K L R S T U V 12±.1 5.4±.1 1.5 +.1 12.5±.1 .4±.05 5.35 ±0.2 2.5 MIN 10 MIN 30.4 MAX 360 MAX 24.4+2-0 *Compliant to EIA-481A MARKING SPECIFICATIONS ENVIRONMENTAL/MECHANICAL SPECIFICATIONS PARAMETER SPECIFICATION Fine Leak Test Gross Leak Test Mechanical Shock Vibration Solderability Temperature Cycling Resistance to Soldering Heat Resistance to Solvents MIL-STD-883, Method 1014, Condition A MIL-STD-883, Method 1014, Condition C MIL-STD-202, Method 213, Condition C MIL-STD-883, Method 2007, Condition A MIL-STD-883, Method 2002 MIL-STD-883, Method 1010 MIL-STD-883, Method 210 MIL-STD-883, Method 215 Line 1: E XX.XXX Frequency in MHz (5 Digits Maximum + Decimal) MANUFACTURER CATEGORY SERIES PACKAGE CLASS REV.DATE ECLIPTEK CORP. CRYSTAL EC3SM1 EPOXY BASE CR34 06/06 800-ECLIPTEK www.ecliptek.com for latest revision Specifications subject to change without notice.