597D www.vishay.com Vishay Sprague Solid Tantalum Chip Capacitors, TANTAMOUNT®, Ultra-Low ESR, Conformal Coated, Maximum CV FEATURES • New case size offerings • Terminations: 100 % tin (2) standard; tin/lead available Available • Extremely low ESR Available • Mounting: Surface mount • Ripple current up to 4.1 A • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 PERFORMANCE CHARACTERISTICS www.vishay.com/doc?40088 Operating Temperature: - 55 °C to + 125 °C (above 85 °C, voltage derating is required) Capacitance Range: 10 μF to 1500 μF Capacitance Tolerance: ± 10 %, ± 20 % standard Voltage Rating: 4 VDC to 75 VDC Note * This datasheet provides information about parts that are RoHS-compliant and/or parts that are non-RoHS-compliant. For example, parts with lead (Pb) terminations are not RoHS-compliant. Please see the information/tables in this datasheet for details. ORDERING INFORMATION 597D 687 X0 6R3 E 2 T TYPE CAPACITANCE CAPACITANCE TOLERANCE DC VOLTAGE RATING AT + 85 °C CASE CODE TERMINATION REEL SIZE AND PACKAGING This is expressed in pF. The first two digits are the significant figures. The third is the number of zeros to follow. X0 = ± 20 % X9 = ± 10 % This is expressed in V. To complete the three-digit block, zeros precede the voltage rating. A decimal point is indicated by an “R” (6R3 = 6.3 V). See Ratings and Case Codes table 2 = 100 % tin 8 = Solder plated (60/40) special order T = Tape and reel 7" [178 mm] reel Note • Preferred tolerance and reel sizes are in bold. We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Low ESR solid tantalum chip capacitors allow delta ESR of 1.25 times the datasheet limits after mounting. DIMENSIONS in inches [millimeters] J Tantalum wire nib identifies anode (+) terminal W L H D B A CASE CODE V D E R F Z M H L (MAX.) 0.299 [7.6] 0.299 [7.6] 0.299 [7.6] 0.299 [7.6] 0.299 [7.6] 0.299 [7.6] 0.315 [8.0] 0.315 [8.0] W 0.173 ± 0.016 [4.4 ± 0.4] 0.173 ± 0.016 [4.4 ± 0.4] 0.173 ± 0.016 [4.4 ± 0.4] 0.238 ± 0.016 [6.0 ± 0.4] 0.238 ± 0.016 [6.0 ± 0.4] 0.238 ± 0.016 [6.0 ± 0.4] 0.260 + 0.016/- 0.024 [6.6 + 0.4/- 0.6] 0.260 + 0.016/- 0.024 [6.6 + 0.4/- 0.6] H 0.079 [2.0 max.] 0.138 [3.5 max.] 0.157 ± 0.016 [4.0 ± 0.4] 0.142 ± 0.016 [3.6 ± 0.4] 0.185 ± 0.016 [4.7 ± 0.4] 0.236 ± 0.016 [6.0 ± 0.4] 0.142 ± 0.016 [3.6 ± 0.4] 0.205 ± 0.016 [5.2 ± 0.4] A 0.051 ± 0.012 [1.3 ± 0.3] 0.051 ± 0.012 [1.3 ± 0.3] 0.051 ± 0.012 [1.3 ± 0.3] 0.051 ± 0.012 [1.3 ± 0.3] 0.055 ± 0.016 [1.4 ± 0.4] 0.055 ± 0.016 [1.4 ± 0.4] 0.051 ± 0.012 [1.3 ± 0.3] 0.055 ± 0.016 [1.4 ± 0.4] B 0.181 ± 0.024 [4.6 ± 0.6] 0.181 ± 0.024 [4.6 ± 0.6] 0.181 ± 0.024 [4.6 ± 0.6] 0.181 ± 0.024 [4.6 ± 0.6] 0.181 ± 0.024 [4.6 ± 0.6] 0.181 ± 0.024 [4.6 ± 0.6] 0.197 ± 0.024 [5.0 ± 0.6] 0.197 ± 0.024 [5.0 ± 0.6] D (REF.) 0.252 [6.4] 0.252 [6.4] 0.252 [6.4] 0.244 [6.2] 0.244 [6.2] 0.244 [6.2] 0.260 [6.6] 0.260 [6.6] J (MAX.) 0.004 [0.1] 0.004 [0.1] 0.004 [0.1] 0.004 [0.1] 0.004 [0.1] 0.004 [0.1] 0.004 [0.1] 0.004 [0.1] Note • The anode termination (D less B) will be a minimum of 0.012" [0.3 mm] Revision: 25-Jun-13 Document Number: 40047 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 597D www.vishay.com Vishay Sprague RATINGS AND CASE CODES μF 10 15 22 33 47 68 100 150 220 330 470 680 1000 1500 2200 4V 6.3 V V E E R V E E/R R 10 V E E R F 16 V E F H 20 V 25 V 35 V R F F R F F M R H 50 V 63 V D R F E/R R F Z 75 V R STANDARD RATINGS CAPACITANCE (μF) CASE CODE PART NUMBER 470 680 1000 1000 1500 V E E R R 597D477(1)004V(2)(3) 597D687(1)004E(2)(3) 597D108(1)004E(2)(3) 597D108(1)004R(2)(3) 597D158(1)004R(2)(3) 330 470 680 1000 V E E R 597D337(1)6R3V(2)(3) 597D477(1)6R3E(2)(3) 597D687(1)6R3E(2)(3) 597D108(1)6R3R(2)(3) 330 470 680 1000 E E R F 597D337(1)010E(2)(3) 597D477(1)010E(2)(3) 597D687(1)010R(2)(3) 597D108(1)010F(2)(3) 220 330 470 E F H 597D227(1)016E(2)(3) 597D337(1)016F(2)(3) 597D477(1)016H(2)(3) 220 330 R H 597D227(1)020R(2)(3) 597D337(1)020H(2)(3) 68 100 R F 597D686(1)025R(2)(3) 597D107(1)025F(2)(3) MAX. DCL AT + 25 °C (μA) MAX. ESR AT + 25 °C 100 kHz (m) MAX. RIPPLE 100 kHz IRMS (A) 8 6 8 8 8 60 25 20 18 24 2.2 2.9 3.3 3.7 2.9 8 6 6 8 56 30 25 31 2.0 2.7 2.9 2.8 6 6 6 20 35 28 28 120 2.5 2.8 3.0 1.4 8 10 14 60 100 100 2.3 1.6 1.4 8 10 80 100 1.8 1.6 6 8 100 100 1.6 1.6 MAX. DF AT + 25 °C 120 Hz (%) 4 VDC AT + 85 °C; 2.7 VDC AT + 125 °C 19 27 40 40 60 6.3 VDC AT + 85 °C; 4 VDC AT + 125 °C 21 30 43 63 10 VDC AT + 85 °C; 7 VDC AT + 125 °C 33 47 68 100 16 VDC AT + 85 °C; 10 VDC AT + 125 °C 35 53 75 20 VDC AT + 85 °C; 13 VDC AT + 125 °C 44 66 25 VDC AT + 85 °C; 17 VDC AT + 125 °C 17 25 Note • Part number definitions: (1) Tolerance: For 10 % tolerance, specify “X9”, for 20 % tolerance, change to “X0” (2) Termination: For 100 % tin specify “2”, for solder plated 60/40 specify “8” (3) Packaging code: For 7" reels specify “T” Revision: 25-Jun-13 Document Number: 40047 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 597D www.vishay.com Vishay Sprague STANDARD RATINGS CAPACITANCE (μF) CASE CODE PART NUMBER 150 220 F M 597D157(1)025F(2)(3) 597D227(1)025M(2)(3) 47 68 100 R F F 597D476(1)035R(2)(3) 597D686(1)035F(2)(3) 597D107X0035F(2)(3) 15 15 22 33 47 E R R F Z 597D156(1)050E(2)(3) 597D156(1)050R(2)(3) 597D226(1)050R(2)(3) 597D336(1)050F(2)(3) 597D476(1)050Z(2)(3) 10 15 22 D R F 597D106(1)063D(2)(3) 597D156(1)063R(2)(3) 597D226(1)063F(2)(3) 10 R 597D106(1)075R(2)(3) MAX. DCL AT + 25 °C (μA) MAX. DF AT + 25 °C 120 Hz (%) MAX. ESR AT + 25 °C 100 kHz (m) MAX. RIPPLE 100 kHz IRMS (A) 8 8 80 100 1.8 1.6 6 6 8 100 100 100 1.6 1.6 1.6 6 6 6 6 6 300 250 220 150 240 0.9 1.0 1.1 1.3 1.1 6 6 6 400 400 250 0.6 0.8 1.0 6 500 0.7 25 VDC AT + 85 °C; 17 VDC AT + 125 °C 38 55 35 VDC AT + 85 °C; 23 VDC AT + 125 °C 17 24 35 50 VDC AT + 85 °C; 33 VDC AT + 125 °C 8 8 11 17 24 63 VDC AT + 85 °C; 42 VDC AT + 125 °C 10 10 14 75 VDC AT + 85 °C; 50 VDC AT + 125 °C 8 Note • Part number definitions: (1) Tolerance: For 10 % tolerance, specify “X9”, for 20 % tolerance, change to “X0” (2) Termination: For 100 % tin specify “2”, for solder plated 60/40 specify “8” (3) Packaging code: For 7" reels specify “T” RECOMMENDED VOLTAGE DERATING GUIDELINES (for temperature below + 85 °C) STANDARD CONDITIONS. FOR EXAMPLE: OUTPUT FILTERS Capacitor Voltage Rating 4.0 6.3 10 16 20 25 35 50 63 75 SEVERE CONDITIONS. FOR EXAMPLE: INPUT FILTERS Capacitor Voltage Rating 4.0 6.3 10 16 20 25 35 50 63 75 Revision: 25-Jun-13 Operating Voltage 2.5 3.6 6.0 10 12 15 24 28 37.8 45 Operating Voltage 2.5 3.3 5.0 8.0 10 12 15 24 32 37 Document Number: 40047 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 597D www.vishay.com Vishay Sprague TYPICAL CURVES 1500 μF - 4 V “R” CASE SIZE ESR and Z vs. FREQUENCY 330 μF - 10 V “E” CASE SIZE ESR and Z vs. FREQUENCY 1 1 ESR Z ESR and Z (Ω) ESR and Z () ESR Z 0.1 0.01 100 Hz 1 kHz 10 kHz FREQUENCY 100 kHz 1 MHz 0.1 0.01 100 Hz 1 kHz 10 kHz 100 kHz 1000 μF - 6.3 V “R” CASE SIZE ESR and Z vs. FREQUENCY 330 μF - 6.3 V “V” CASE SIZE and Z vs. FREQUENCY 10 1 ESR Z ESR Z ESR and Z () ESR and Z () 1 MHz FREQUENCY 1 0.1 0.1 0.01 0.01 100 Hz 1 kHz 10 kHz 100 kHz 1 MHz 100 Hz 1 kHz 10 kHz 100 kHz 1 MHz FREQUENCY FREQUENCY 470 μF - 4 V “V” CASE SIZE ESR and Z vs. FREQUENCY 10 ESR and Z (Ω) ESR Z 1 0.1 0.01 100 Hz 1 kHz 10 kHz 100 kHz 1 MHz FREQUENCY Revision: 25-Jun-13 Document Number: 40047 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 597D www.vishay.com Vishay Sprague POWER DISSIPATION CASE CODE MAXIMUM PERMISSIBLE POWER DISSIPATION AT + 25 °C (W) IN FREE AIR V 0.141 D 0.215 E 0.240 R, F, M 0.250 Z 0.265 H 0.265 STANDARD PACKAGING QUANTITY CASE CODE UNITS PER 7" REEL V 1000 D 400 E 500 R 300 F 250 Z 250 M 200 H 200 PRODUCT INFORMATION Conformal Coated Guide Pad Dimensions www.vishay.com/doc?40150 Packaging Dimensions Moisture Sensitivity www.vishay.com/doc?40135 SELECTOR GUIDES Solid Tantalum Selector Guide www.vishay.com/doc?49053 FAQ Frequently Asked Questions Revision: 25-Jun-13 www.vishay.com/doc?40110 Document Number: 40047 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000