AD AD13465AZ Dual channel, 14-bit, 65 msps a/d converter with analog input signal conditioning Datasheet

a
Dual Channel, 14-Bit, 65 MSPS A/D Converter
with Analog Input Signal Conditioning
AD13465
FEATURES
Dual, 65 MSPS Minimum Sample Rate
Channel-to-Channel Matching, ⴞ1% Gain Error
90 dB Channel-to-Channel Isolation
DC-Coupled Signal Conditioning
85 dB Spurious-Free Dynamic Range
Selectable Bipolar Inputs
(ⴞ1 V and ⴞ0.5 V Ranges)
Integral Two-Pole Low-Pass Nyquist Filter
Two’s Complement Output Format
3.3 V Compatible Outputs
1.8 W per Channel
Industrial and Military Grade
state-of-the-art high-density circuit design and laser-trimmed
thin-film resistor networks to achieve exceptional channel
matching and impedance control, and provide for significant
board area savings.
Multiple options are provided for driving the analog input, including single-ended, differential, and optional series filtering. The
AD13465 also offers the user a choice of analog input signal
ranges to further minimize additional external signal conditioning, while remaining general-purpose. The AD13465 operates
with ± 5.0 V for the analog signal conditioning, 5.0 V supply for
the analog-to-digital conversion, and 3.3 V digital supply for
the output stage. Each channel is completely independent, allowing operation with independent Encode and Analog Inputs, while
maintaining minimal crosstalk and interference.
APPLICATIONS
Radar Processing
Optimized for I/Q Baseband Operation
Phased Array Receivers
Multichannel, Multimode Receivers
GPS Antijamming Receivers
Communications Receivers
The AD13465 is packaged in a 68-lead ceramic gull wing
package. Manufacturing is done on Analog Devices’ MIL38534 Qualified Manufacturers Line (QML) and components
are available up to Class-H (–40°C to +85°C). The components
are manufactured using Analog Devices’ high-speed complementary bipolar process (XFCB).
PRODUCT DESCRIPTION
PRODUCT HIGHLIGHTS
The AD13465 is a complete dual channel signal processing
solution including on-board amplifiers, references, ADCs,
and output termination components to provide optimized
system performance. The AD13465 has on-chip track-and-hold
circuitry and utilizes an innovative multipass architecture to
achieve 14-bit, 65 MSPS performance. The AD13465 uses
1. Guaranteed sample rate of 65 MSPS.
2. Input signal conditioning included; gain and impedance
matching.
3. Single-ended, differential, or off-module filter options.
4. Fully tested/characterized full channel performance
5. Pin compatible with 12-bit AD13280 product family.
FUNCTIONAL BLOCK DIAGRAM
AMP-IN-A-2
AMP-IN-A-1
AMP-IN-B-2
AMP-IN-B-1
AMP-OUT-B
AMP-OUT-A
A–IN
B+IN
A+IN
B–IN
DROUTA
(LSB) D0A
DROUTB
AD13465
D1A
ENC
D2A
TIMING
D3A
D4A
VREF
D5A
DROUT
D6A
D7A
D8A
D9A
VREF
DROUT
D13B (MSB)
14
D12B
14
11
100⍀ OUTPUT TERMINATORS
TIMING
3
100⍀ OUTPUT TERMINATORS
5
ENC ENC
D11A D12A D13A
(MSB)
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
D11B
D10B
9
D9B
D10A
REV. 0
ENC
D0B D1B D2B D3B D4B D5B
(LSB)
D6B D7B D8B
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2001
(AVCC = 5 V; AVEE = –5 V; DVCC = 3.3 V applies to each ADC with Front
AD13465–TARGET SPECIFICATIONS End Amplifier unless otherwise noted.)
Parameter
Temp
Test
Level
Mil SubGroup
Min
RESOLUTION
DC ACCURACY
No Missing Codes
Offset Error
AD13465AZ/BZ
Typ
Max
14
IV
I
VI
VI
I
VI
I
VI
VI
Full
Full
V
V
Full
Full
IV
IV
Full
V
100
200
4.0
100
DIFFERENTIAL ANALOG INPUT
Analog Signal Input Range
A+IN to A–IN and B+IN to B–IN 4
Input Impedance
Analog Input Bandwidth 3
Full
Full
Full
V
V
V
± 1.0
618
50
V
Ω
MHz
ENCODE INPUT (ENC, ENC) 5
Differential Input Voltage
Differential Input Resistance
Differential Input Capacitance
Full
25°C
25°C
IV
V
V
12
10
2.5
V p-p
kΩ
pF
Full
Full
25°C
25°C
25°C
25°C
25°C
Full
Full
VI
IV
V
IV
V
IV
IV
IV
V
4, 5, 6
12
25°C
25°C
Full
25°C
Full
25°C
Full
V
I
II
I
II
V
V
25°C
25°C
Full
25°C
Full
25°C
Full
V
I
II
I
II
V
V
Gain Error Channel Match
SINGLE-ENDED ANALOG INPUT
Input Voltage Range
AMP-IN-X-1
AMP-IN-X-2
Input Resistance
AMP-IN-X-1
AMP-IN-X-2
Input Capacitance2
Analog Input Bandwidth 3
SWITCHING PERFORMANCE
Maximum Conversion Rate 6
Minimum Conversion Rate 6
Aperture Delay (tA)
Aperture Delay Matching
Aperture Uncertainty (Jitter)
ENCODE Pulse with High
ENCODE Pulse with Low
Output Delay (tOD)
Encode, Rising to Data Ready,
Rising Delay
SNR7
Analog Input @ 4.98 MHz
Analog Input @ 9.9 MHz
Analog Input @ 21 MHz
Analog Input @ 32 MHz
SINAD8
Analog Input @ 4.98 MHz
Analog Input @ 9.9 MHz
Analog Input @ 21 MHz
Analog Input @ 32 MHz
–2.2
–2.2
–1.0
–3.0
–5.0
+1.5
–3.0
–5.0
Guaranteed
± 0.2
± 1.0
± 0.1
–1.0
± 2.0
± 0.5
± 1.0
± 1.0
Bits
Full
25°C
Full
Full
25°C
Full
25°C
Max
Min
Offset Error Channel Match
Gain Error1
12
1
2, 3
1, 2, 3
1
2, 3
1
2
3
Unit
+2.2
+2.2
+1.0
+1.0
+5.0
+1.5
+3.0
+5.0
± 0.5
± 1.0
12
12
99
198
–2–
V
V
101
202
7.0
0.4
65
20
12
12
12
12
5.0
5.0
4
5, 6
4
5, 6
70
69
69
68
4
5, 6
4
5, 6
69
68.5
66.5
66
1.5
250
0.3
7.7
7.7
7.5
11.5
% FS
% FS
% FS
% FS
% FS
% FS
% FS
% FS
500
9.5
9.5
Ω
Ω
pF
MHz
MSPS
MSPS
ns
ps
ps rms
ns
ns
ns
ns
72
72
71
71
70
70
69
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
72
72
70.5
70
69
63
61
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
REV. 0
AD13465
Temp
Test
Level
25°C
25°C
Full
25°C
Full
25°C
Full
V
I
II
I
II
V
V
SINGLE-ENDED ANALOG INPUT
Pass Band Ripple to 10 MHz
Pass Band Ripple to 25 MHz
25°C
25°C
DIFFERENTIAL ANALOG INPUT
Pass Band Ripple to 10 MHz
Pass Band Ripple to 25 MHz
Parameter
SPURIOUS-FREE DYNAMIC RANGE
Analog Input @ 4.98 MHz
Analog Input @ 9.9 MHz
Mil SubGroup
Min
4
5, 6
4
5, 6
80
78
70
69
AD13465AZ/BZ
Typ
Max
Unit
9
85
86
84
76
74
63
62
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
V
V
0.05
0.1
dB
dB
25°C
25°C
V
V
0.3
0.82
dB
dB
TWO-TONE IMD REJECTION 10
fIN = 9.1 MHz and 10.1 MHz
f1 and f2 are –7 dB
fIN = 19.1 MHz and 20.7 MHz
f1 and f2 are –7 dB
25°C
Full
25°C
I
II
V
4
5, 6
82
80
72
dBc
CHANNEL-TO-CHANNEL ISOLATION 11
25°C
IV
12
TRANSIENT RESPONSE
25°C
V
Analog Input @ 21 MHz
Analog Input @ 32 MHz
DIGITAL OUTPUTS
Logic Compatibility
DVCC = 3.3 V
Logic 1 Voltage
Logic 0 Voltage
DVCC = 5 V
Logic 1 Voltage
Logic 0 Voltage
Output Coding
77.5
76.5
dBc
90
dB
15.3
ns
12
POWER SUPPLY
AVCC Supply Voltage13
I (AVCC) Current
AVEE Supply Voltage13
I (AVEE) Current
DVCC Supply Voltage13
I (DVCC) Current
(Total) Supply Current per Channel
Power Dissipation (Total)
Power Supply Rejection Ratio (PSRR)
CMOS
Full
Full
I
I
Full
Full
V
V
Full
Full
Full
Full
Full
Full
Full
Full
Full
VI
V
VI
V
VI
V
I
I
V
1, 2, 3
1, 2, 3
2.5
DVCC – 0.2
0.2
0.5
DVCC – 0.3
0.35
Two’s Complement
4.85
–5.25
3.135
1, 2, 3
1, 2, 3
5.0
270
–5.0
38
3.3
34
369
3.57
0.02
V
V
V
V
5.25
308
–4.75
49
3.465
46
403
3.9
V
mA
V
mA
V
mA
mA
W
% FSR/
% VS
NOTES
1
Gain tests are performed on AMP-IN-X-1 input voltage range.
2
Input capacitance spec. combines AD8037 capacitance and ceramic package capacitance.
3
Full Power Bandwidth is the frequency at which the spectral power of the fundamental frequency (as determined by FFT analysis) is reduced by 3 dB.
4
For differential input: +IN = 1 V p-p and –IN = 1 V p-p (signals are 180 ° out of phase). For single ended input: +IN = 2 V p-p and –IN = GND.
5
All AC specifications tested by driving ENCODE and ENCODE differentially. AMP-IN-X-1 = 1 V p-p, AMP-IN-X-2 = GND.
6
Minimum and Maximum conversion rates allow for variation in Encode Duty Cycle of 50% ± 5%.
7
Analog Input signal power at –1 dBFS; signal-to-noise ratio (SNR) is the ratio of signal level to total noise (first five harmonics removed).
Encode = 65 MSPS. SNR is reported in dBFS, related back to converter full scale.
8
Analog Input signal power at –1 dBFS; signal-to-noise and distortion (SINAD) is the ratio of signal level to total noise + harmonics.
Encode = 65 MSPS. SINAD is reported in dBFS, related back to converter full scale.
9
Analog Input signal power at –1 dBFS; SFDR is ratio of converter full scale to worst spur.
10
Both input tones at –7 dBFS; two tone intermodulation distortion (IMD) rejection is the ratio of either tone to the worst third order intermod product.
11
Channel-to-channel isolation tested with A Channel grounded and a full-scale signal applied to B Channel.
12
Digital output logic levels: DV CC = 3.3 V, C LOAD = 10 pF. Capacitive loads > 10 pF will degrade performance.
13
Supply voltage recommended operating range. AV CC may be varied from 4.85 V to 5.25 V. However, rated ac (harmonics) performance is valid only over the range
AVCC = 5.0 V to 5.25 V.
Specifications subject to change without notice.
REV. 0
–3–
AD13465
ABSOLUTE MAXIMUM RATINGS 1
TEST LEVEL
ELECTRICAL
AVCC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to 7 V
AVEE Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . –7 V to 0 V
DVCC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to 7 V
Analog Input Voltage . . . . . . . . . . . . . . . . . . . . . VEE to VCC
Analog Input Current . . . . . . . . . . . . . . –10 mA to +10 mA
Digital Input Voltage (ENCODE) . . . . . . . . . . . . . 0 to VCC
ENCODE, ENCODE Differential Voltage . . . . . . . . . . 4 V
Digital Output Current . . . . . . . . . . . . –10 mA to +10 mA
ENVIRONMENTAL2
Operating Temperature (Case) . . . . . . . . . –40°C to +85°C
Maximum Junction Temperature . . . . . . . . . . . . . . . 175°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . 300°C
Storage Temperature Range (Ambient) . . –65°C to +150°C
I
100% Production Tested.
II
100% Production Tested at 25°C, and sample tested at
specified temperatures. AC testing done on sample basis.
III Sample Tested Only.
IV Parameter is guaranteed by design and characterization testing.
V
Parameter is a typical value only.
VI 100% production tested at temperature at 25°C: sample
tested at temperature extremes.
NOTES
1
Absolute maximum ratings are limiting values applied individually, and beyond
which the serviceability of the circuit may be impaired. Functional operability is not
necessarily implied. Exposure to absolute maximum rating conditions for an
extended period of time may affect device reliability.
2
Typical thermal impedance for “ES” package: θJC, 2.2°C/W; θJA, 24.3°C/W.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD13465 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
ORDERING GUIDE
Model
Temperature Range (Case)
Package Description
Package Option
AD13465AZ
AD13465AF
–25°C to +85°C
–25°C to +85°C
ES-68C
ES-68C
5962-0150601HXA
AD13465/PCB
–40°C to +85°C
25°C
68-Lead Ceramic Leaded Chip Carrier
68-Lead Ceramic Leaded Chip Carrier
with Nonconductive Tie-Bar
68-Lead Ceramic Leaded Chip Carrier
Evaluation Board with AD13465AZ
–4–
ES-68C
REV. 0
AD13465
PIN FUNCTION DESCRIPTIONS
Pin No.
Mnemonic
Function
1, 35
2, 3, 9, 10, 13, 16
SHIELD
AGNDA
4
5
6
7
8
11
12
14
15
17
18–25, 28–33
26, 27
34
36
37–42, 45–52
43, 44
53
54, 57, 60, 61, 67, 68
55
56
58
59
62
63
64
65
66
A–IN
A+IN
AMP-OUT-A
AMP-IN-A-1
AMP-IN-A-2
AVEEA
AVCCA
ENCA
ENCA
DVCCA
D0A–D13A
DGNDA
DROUTA
DROUTB
D0B–D13B
DGNDB
DVCCB
AGNDB
ENCB
ENCB
AVCCB
AVEEB
AMP-IN-B-2
AMP-IN-B-1
AMP-OUT-B
B+IN
B–IN
Internal Ground Shield Between Channels.
A Channel Analog Ground. A and B grounds should be connected as close to the
device as possible.
Inverting Differential Input (Gain = 1).
Noninverting Differential Input (Gain = 1).
Single-Ended Amplifier Output (Gain = 2).
Analog Input for A Side ADC (Nominally ± 0.5 V).
Analog Input for A Side ADC (Nominally ± 1.0 V).
A Channel Analog Negative Supply Voltage (Nominally –5.0 V or –5.2 V).
A Channel Analog Positive Supply Voltage (Nominally 5.0 V).
Complement of Encode; Differential Input.
Encode Input; Conversion Initiated on Rising Edge.
A Channel Digital Positive Supply Voltage (Nominally 5.0 V/3.3 V).
Digital Outputs for ADC A. D0 (LSB).
A Channel Digital Ground.
Data Ready A Output.
Data Ready B Output.
Digital Outputs for ADC B. D0 (LSB).
B Channel Digital Ground.
B Channel Digital Positive Supply Voltage (Nominally 5.0 V/3.3 V).
B Channel Analog Ground.
Encode Input; Conversion Initiated on Rising Edge.
Complement of Encode; Differential Input.
B Channel Analog Positive Supply Voltage (Nominally 5.0 V).
B Channel Analog Negative Supply Voltage (Nominally –5.0 V or –5.2 V).
Analog Input for B Side ADC (Nominally ± 1.0 V).
Analog Input for B Side ADC (Nominally ± 0.5 V).
Single-Ended Amplifier Output (Gain = 2).
Noninverting Differential Input (Gain = 1).
Inverting Differential Input (Gain = 1).
AGNDA
SHIELD
AGNDB
4
2
1 68 67 66 65 64 63 62 61
5
3
AGNDB
A–IN
AGNDA
6
AMP-IN-B-1
AMP-IN-B-2
AMP-OUT-A
A+IN
7
B+IN
AMP-OUT-B
AMP-IN-A-1
8
B–IN
AMP-IN-A-2
9
AGNDA 10
AVEEA 11
AGNDB
AGNDA
PIN CONFIGURATION
59
AGNDB
AVEEB
AVCCA 12
AGNDA 13
ENCA 14
58
AVCCB
57
56
AGNDB
ENCB
ENCA 15
AGNDA 16
DVCCA 17
55
ENCB
54
60
PIN 1
IDENTIFIER
D0A(LSB) 18
D1A 19
AD13465
53
AGNDB
DVCCB
TOP VIEW
(Not to Scale)
52
D13B(MSB)
51
D2A 20
50
D12B
D11B
D3A 21
49
D10B
D4A 22
48
D9B
D5A 23
47
D8B
D6A 24
46
D7B
D7A 25
DGNDA 26
45
D6B
DGNDB
44
REV. 0
–5–
DGNDB
D5B
D3B
D4B
D2B
D1B
DROUTB
D0B(LSB)
SHIELD
DROUTA
D12A
D13A(MSB)
D9A
D10A
D11A
D8A
DGNDA
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
AD13465 –Typical Performance Characteristics
0
0
ENCODE = 65MSPS
AIN = 5MHz(–1dBFS)
SNR = 72.12dBFS
SFDR = 86.05dBc
–10
–20
–20
–30
–40
–40
–50
–50
–60
–60
dB
dB
–30
ENCODE = 65MSPS
AIN = 9.9MHz(–1dBFS)
SNR = 72.09dBFS
SFDR = 84.04dBc
–10
–70
–80
–70
–80
–90
–90
–100
–100
–110
–110
–120
–120
–130
–130
0
2.5 5.0 7.5 10.0 12.5 15.0 17.5 20.0 22.5 25.0 27.5 30.0 32.5
0
FREQUENCY – MHz
FREQUENCY – MHz
TPC 1. Single Tone @ 5 MHz
TPC 4. Single Tone @ 9.9 MHz
0
0
ENCODE = 65MSPS
AIN = 21MHz(–1dBFS)
SNR = 71.74dBFS
SFDR = 73.07dBc
–10
–20
ENCODE = 65MSPS
AIN = 32MHz(–1dBFS)
SNR = 70.8dBFS
SFDR = 62.57dBc
–10
–20
–30
–40
–40
–50
–50
–60
–60
dB
dB
–30
–70
–70
–80
–80
–90
–90
–100
–100
–110
–110
–120
–120
–130
–130
0
0
2.5 5.0 7.5 10.0 12.5 15.0 17.5 20.0 22.5 25.0 27.5 30.0 32.5
2.5 5.0 7.5 10.0 12.5 15.0 17.5 20.0 22.5 25.0 27.5 30.0 32.5
FREQUENCY – MHz
FREQUENCY – MHz
TPC 2. Single Tone @ 21 MHz
TPC 5. Single Tone @ 32 MHz
0
0
ENCODE = 65MSPS
AIN = 9.1MHz AND 10.1MHz(–1dBFS)
SFDR = 85.01dBc
–10
–20
ENCODE = 65MSPS
AIN = 19MHz AND
20.7MHz(–1dBFS)
SNR = 70.8dBFS
SFDR = 75.40dBc
–10
–20
–30
–30
–40
–40
–50
–50
–60
–60
dB
dB
2.5 5.0 7.5 10.0 12.5 15.0 17.5 20.0 22.5 25.0 27.5 30.0 32.5
–70
–70
–80
–80
–90
–90
–100
–100
–110
–110
–120
–120
–130
–130
0
0
2.5 5.0 7.5 10.0 12.5 15.0 17.5 20.0 22.5 25.0 27.5 30.0 32.5
2.5 5.0 7.5 10.0 12.5 15.0 17.5 20.0 22.5 25.0 27.5 30.0 32.5
FREQUENCY – MHz
FREQUENCY – MHz
TPC 3. Two-Tone @ 9.1 MHz/10.1 MHz
TPC 6. Two-Tone @ 19 MHz/20.7 MHz
–6–
REV. 0
AD13465
3.0
3.0
ENCODE = 65MSPS
DNL MAX = 0.632 CODES
DNL MIN = –0.52 CODES
2.5
ENCODE = 65MSPS
INL MAX = 1.18 CODES
INL MIN = –1.06 CODES
2.0
2.0
1.0
LSB
LSB
1.5
1.0
0
0.5
–1.0
0
–2.0
–0.5
–1.0
–3.0
0
2048
4096
6144
8192
0
10240 12288 14336 16384
TPC 7. Differential Nonlinearity
2048
4096
6144
8192
TPC 10. Integral Nonlinearity
0
0
ENCODE = 40MSPS
AIN = 5MHz(–1dBFS)
SNR = 72dBFS
SFDR = 87.57dBc
–10
–1
–20
ENCODE = 65MSPS
ROLLOFF = –0.18dB
–30
–3
–40
–4
–50
dB
dBFS
–2
10240 12288 14336 16384
–5
–6
–60
–70
–80
–90
–7
–100
–8
–110
–9
–120
–10
1.0
3.5
6.0
8.5
11.0 13.5
16.0
18.5
21.0
23.5
–130
0
26.0
2.5
5.0
TPC 8. Passband Ripple to 25 MHz
–30
–10
–20
–30
–40
–40
–50
–50
–60
–60
dB
dB
12.5
15.0
17.5
20.0
17.5
20.0
0
ENCODE = 40MSPS
AIN = 9.1MHz AND
10.1MHz(–1dBFS)
SFDR = 84.16dBc
–20
–70
ENCODE = 40MSPS
AIN = 18MHz(–1dBFS)
SNR = 71.5dBFS
SFDR = 78.7dBc
–70
–80
–80
–90
–90
–100
–100
–110
–110
–120
–120
2.5
5.0
7.5
10.0
12.5
15.0
17.5
–130
0
20.0
FREQUENCY – MHz
2.5
5.0
7.5
10.0
12.5
15.0
FREQUENCY – MHz
TPC 9. Two-Tone @ 9.1 MHz/10.1 MHz
REV. 0
10.0
TPC 11. Single Tone @ 5 MHz
0
–10
–130
0
7.5
FREQUENCY – MHz
FREQUENCY – MHz
TPC 12. Single Tone @ 18 MHz
–7–
AD13465
DEFINITION OF SPECIFICATIONS
Analog Bandwidth
Minimum Conversion Rate
The encode rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed limit.
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Maximum Conversion Rate
The encode rate at which parametric testing is performed.
Aperture Delay
Output Propagation Delay
The delay between a differential crossing of ENCODE and
ENCODE command and the instant at which the analog input
is sampled.
The delay between a differential crossing of ENCODE and
ENCODE command and the time when all output data bits are
within valid logic levels.
Aperture Uncertainty (Jitter)
Overvoltage Recovery Time
The sample-to-sample variation in aperture delay.
The amount of time required for the converter to recover to
0.02% accuracy after an analog input signal of the specified
percentage of full scale is reduced to midscale.
Differential Analog Input Resistance, Differential Analog
Input Capacitance, and Differential Analog Input Impedance
The real and complex impedances measured at each analog
input port. The resistance is measured statically and the capacitance and differential input impedances are measured with a
network analyzer.
Power Supply Rejection Ratio
The ratio of a change in input offset voltage to a change in
power supply voltage.
Signal-to-Noise-and-Distortion (SINAD)
Differential Analog Input Voltage Range
The ratio of the rms signal amplitude (set at 1 dB below full
scale) to the rms value of the sum of all other spectral components, including harmonics but excluding dc. May be reported
in dB (i.e., degrades as signal level is lowered) or in dBFS
(always related back to converter full scale).
The peak-to-peak differential voltage that must be applied to
the converter to generate a full-scale response. Peak differential
voltage is computed by observing the voltage from the other pin,
which is 180 degrees out of phase. Peak-to-peak differential is
computed by rotating the inputs phase 180 degrees and taking
the peak measurement again. The difference is then computed
between both peak measurements.
Signal-to-Noise Ratio (without Harmonics)
The ratio of the rms signal amplitude (set at 1 dB below full scale)
to the rms value of the sum of all other spectral components,
excluding the first five harmonics and dc. May be reported in
dB (i.e., degrades as signal level is lowered) or in dBFS (always
related back to converter full scale).
Differential Nonlinearity
The deviation of any code from an ideal 1 LSB step.
Encode Pulsewidth/Duty Cycle
Pulsewidth high is the minimum amount of time that the
ENCODE pulse should be left in Logic 1 state to achieve rated
performance; pulsewidth low is the minimum time ENCODE
pulse should be left in low state. At a given clock rate, these
specs define an acceptable encode duty cycle.
Spurious-Free Dynamic Range
The ratio of the rms signal amplitude to the rms value of the
peak spurious spectral component. The peak spurious component may or may not be a harmonic.
Transient Response
Harmonic Distortion
The time required for the converter to achieve 0.02% accuracy when a one-half full-scale step function is applied to the
analog input.
The ratio of the rms signal amplitude to the rms value of the
worst harmonic component.
Integral Nonlinearity
Two-Tone Intermodulation Distortion Rejection
The deviation of the transfer function from a reference line
measured in fractions of 1 LSB using a “best straight line”
determined by a least square curve fit.
The ratio of the rms value of either input tone to the rms value
of the worst third order intermodulation product; reported in dBc.
tA
N+3
N
AIN
N+1
N+2
t ENC
ENC, ENC
t ENCH
N
N+4
t ENCL
N+2
N+1
N+3
N+4
t E_DR
D[13:0]
N–3
N–2
t OD
N–1
N
DRY
Figure 1. Timing Diagram
–8–
REV. 0
AD13465
THEORY OF OPERATION
AMP-IN-X-1
100⍀
AMP-IN-X-2
The AD13465 is a high-dynamic range, 14-bit, 65 MHz pipeline delay (three pipelines) analog-to-digital converter. The
custom analog input section provides input ranges of 1 V p-p and
2 V p-p, and input impedance configurations of 50 Ω, 100 Ω,
and 200 Ω.
TO AD8037
100⍀
Figure 2. Single-Ended Input Stage
The AD13465 employs four monolithic ADI components per
channel (AD8037, AD8138, AD8031, and AD6644), along
with multiple passive resistor networks and decoupling capacitors
to fully integrate a complete 14-bit analog-to-digital converter.
LOADS
AVCC
AVCC
AVCC
AVCC
10k⍀
10k⍀
ENCODE
ENCODE
10k⍀
10k⍀
LOADS
Figure 3. ENCODE Inputs
In the single-ended input configuration, the input signal is
passed through a precision laser trimmed resistor divider allowing
the user to externally select operation with a full-scale signal of
± 0.5 V or ± 1.0 V by choosing the proper input terminal for the
application. The result of the resistor divider is to apply a full-scale
input approximately 0.4 V to the noninverting input of the
internal AD8037 amplifier.
The AD13465 analog input includes an AD8037 amplifier
featuring an innovative architecture that maximizes the dynamic
range capability on the amplifier’s inputs and outputs. The
AD8037 amplifier provides a high-input impedance and gain for
driving the AD8138 in a single-ended-to-differential amplifier
configuration. The AD8138 has a –3 dB bandwidth at 300 MHz
and delivers a differential signal with the lowest harmonic
distortion available in a differential amplifier. The AD8138
differential outputs help balance the differential inputs to the
AD6644 maximizing the performance of the device.
DVCC
CURRENT MIRROR
DVCC
VREF
DR OUT
CURRENT MIRROR
The AD8031 provides the buffer for the internal reference
analog-to-digital converter. The internal reference voltage of the
AD6644 is designed to track the offsets and drifts and is used to
ensure matching over an extended temperature range of operation. The reference voltage is connected to the output common
mode input on the AD8138. This reference voltage sets the
output common mode on the AD8138 at 2.4 V, which is the
midsupply level for the ADC.
The AD6644 has complementary analog input pins, AIN and
AIN. Each analog input is centered at 2.4 V and should swing
± 0.55 V around this reference. Since AIN and AIN are 180
degrees out of phase, the differential analog input signal is 2.2 V
peak-to-peak. Both analog inputs are buffered prior to the first
track-and-hold.
Figure 4. Digital Output Stage
DVCC
The AD6644 digital outputs drive 100 Ω series resistors (Figure
5.) The result is a 14-bit parallel digital CMOS-compatible
word, coded as two’s complement.
CURRENT MIRROR
USING THE SINGLE-ENDED INPUT
DVCC
VREF
100⍀
D0–D13
CURRENT MIRROR
Figure 5. Digital Output Stage
REV. 0
The AD13465 has been designed with the user’s ease of operation in mind. Multiple input configurations have been included
on board to allow the user a choice of input signal levels and
input impedance. The standard inputs are ± 0.5 V and ± 1.0 V.
The user can select the input impedance of the AD13465 on
any input by using the other inputs as alternate locations for the
GND. The following chart summarizes the impedance options
available at each input location.
AMP-IN-X-1 = 100 Ω when AMP-IN-X-2 is open.
AMP-IN-X-1 = 50 Ω when AMP-IN-X-2 is shorted to GND.
AMP-IN-X-2 = 200 Ω when AMP-IN-X-1 is open.
Each channel has two analog inputs AMP-IN-A-1 and AMPIN-A-2 or AMP-IN-B-1 and AMP-IN-B-2. Use AMP-IN-A-1
–9–
AD13465
or AMP-IN-B-1 when an input of ±5 V full scale is desired. Use
AMP-IN-A-2 or AMP-IN-B-2 when ± 1 V full scale is desired.
Each channel has an AMP-OUT that must be tied to either a
noninverting or inverting input of a differential amplifier with
the remaining input grounded. For example, Side A, AMPOUT-A (Pin 6) must be tied to A+IN (Pin 5) with A–IN (Pin 4)
tied to ground for noninverting operation or AMP-OUT-A (Pin 6)
tied to A–IN (Pin 4) with A+IN (Pin 5) tied to ground for
inverting operation.
If a low jitter ECL/PECL clock is available, another option is to
ac-couple a differential ECL/PECL signal to the encode input
pins as shown below. A device that offers excellent jitter performance is the MC100LVEL16 (or same family) from Motorola.
VT
0.1␮F
ENCODE
ECL/
PECL
AD13465
0.1␮F
ENCODE
USING THE DIFFERENTIAL INPUT
APPLYING THE AD13465
Encoding the AD13465
The AD13465 encode signal must be a high quality, extremely
low phase noise source, to prevent degradation of performance.
Maintaining 14-bit accuracy at 65 MSPS places a premium on
encode clock phase noise. SNR performance can easily degrade
3 dB to 4 dB with 32 MHz input signals when using a high-jitter
clock source. See Analog Devices’ Application Note AN-501,
“Aperture Uncertainty and ADC System Performance,” for
complete details. For optimum performance, the AD13465
must be clocked differentially. The encode signal is usually
ac-coupled into the ENCODE and ENCODE pins via a transformer or capacitors. These pins are biased internally and require
no additional bias.
VT
Figure 7. Differential ECL for Encode
Jitter Consideration
The signal-to-noise ratio (SNR) for any ADC can be predicted.
When normalized to ADC codes, the equation below, accurately
predicts the SNR based on three terms. These are jitter, average
DNL error, and thermal noise. Each of these terms contributes
to the noise within the converter.
1/ 2
2

 
V
(1 + ε 
SNR = –20 × log  N  + (2 × π × f ANALOG × t J RMS )2 +  NOISEN RMS  
 2 
2
 



fANALOG
= analog input frequency
tJ RMS
= rms jitter of the encode (rms sum of encode
source and internal encode circuitry)
ε
= average DNL of the ADC (typically 0.50 LSB)
N
= Number of bits in the ADC
VNOISE RMS = V rms noise referred to the analog input of the
ADC (typically 5 LSB)
For a 14-bit analog-to-digital converter like the AD13465, aperture jitter can greatly affect the SNR performance as the analog
frequency is increased. The chart below shows a family of curves
that demonstrates the expected SNR performance of the AD13465
as jitter increases. The chart is derived from the above equation.
For a complete discussion of aperture jitter, please consult Analog Devices’ Application Note AN-501, “Aperture Uncertainty
and ADC System Performance.”
Shown below is one preferred method for clocking the AD13465.
The clock source (low jitter) is converted from single-ended to
differential using an RF transformer. The back-to-back Schottky
diodes across the transformer secondary limit clock excursions
into the AD13465 to approximately 0.8 V p-p differential. This
helps prevent the large voltage swings of the clock from feeding
through to the other portions of the AD13465, and limits the
noise presented to the ENCODE inputs. A crystal clock oscillator
can also be used to drive the RF transformer if an appropriate
limited resistor (typically 100 Ω) is placed in the series with
the primary.
71
70
68
67
0.1mF 100 ⍀
AIN = 9.9MHz
66
AIN = 21MHz
65
64
63
62
61
60
CLOCK
SOURCE
AIN = 5MHz
69
SNR – –dBFS
Each channel of the AD13465 was designed with two optional
differential inputs, A+IN, A–IN and B+IN, B–IN. The inputs
provide system designers with the ability to bypass the AD8037
amplifier and drive the AD8138 directly. The AD8138 differential ADC driver can be deployed in either a single-ended or
differential input configuration. The differential analog inputs
have a nominal input impedance of 620 Ω and nominal fullscale input range of 1.2 V p-p. The AD8138 amplifier drives a
differential filter and the custom analog-to-digital converter. The
differential input configuration provides the lowest even-order
harmonics and signal-to-noise (SNR) performance improvement of up to 3 dB (SNR = 73 dBFS). Exceptional care was taken
in the layout of the differential input signal paths. The differential input transmission line characteristics are matched and
balanced. Equal attention to system level signal paths must be
provided in order to realize significant performance improvements.
AIN = 32MHz
59
T1-4T
ENCODE
58
0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4 4.8 5.0
AD13465
CLOCK JITTER – ps
ENCODE
HSMS2812
DIODES
Figure 8. SNR vs. Jitter
Figure 6. Crystal Clock Oscillator—Differential Encode
–10–
REV. 0
AD13465
Power Supplies
LAYOUT INFORMATION
Care should be taken when selecting a power source. Linear
supplies are strongly recommended. Switching supplies tend to
have radiated components that may be received by the AD13465.
Each of the power supply pins should be decoupled as closely to
the package as possible, using 0.1 µF chip capacitors.
The schematic of the evaluation board (Figure 10) represents a
typical implementation of the AD13465. The pinout of the
AD13465 is very straightforward and facilitates ease of use and
the implementation of high frequency/high resolution design
practices. It is recommended that high quality ceramic chip
capacitors be used to decouple each supply pin to ground directly
at the device. All capacitors can be standard high quality ceramic
chip capacitors.
The AD13465 has separate digital and analog power supply pins.
The analog supplies are denoted AVCC and the digital supply
pins are denoted DVCC. AVCC and DVCC should be separate
power supplies. This is because the fast digital output swings
can couple switching current back into the analog supplies.
Note that AVCC must be held within +5% and –3% of 5 V. The
AD13465 is specified for DVCC = 3.3 V as this is a common
supply for digital ASICs.
Output Loading
Care must be taken when designing the data receivers for the
AD13465. The digital outputs drive an internal series resistor
(e.g., 100 Ω) followed by a gate like 75LCX574. To minimize
capacitive loading, there should be only one gate on each output
pin. An example of this is shown in the evaluation board schematic shown in Figure 10. The digital outputs of the AD13465
have a constant output slew rate of 1 V/ns. A typical CMOS
gate combined with a PCB trace will have a load of approximately
10 pF. Therefore, as each bit switches, 10 mA (10 pF × 1 V ÷ 1 ns)
of dynamic current per bit will flow in or out of the device. A fullscale transition can cause up to 140 mA (14 bits × 10 mA/bit)
of transient current through the output stages. These switching currents are confined between ground and the DVCC pin.
Standard TTL gates should be avoided since they can appreciably add to the dynamic switching currents of the AD13465. It
should also be noted that extra capacitive loading will increase
output timing and invalidate timing specifications. Digital output timing is guaranteed with 10 pF loads.
Care should be taken when placing the digital output runs.
Because the digital outputs have such a high slew rate, the
capacitive loading on the digital outputs should be minimized.
Circuit traces for the digital outputs should be kept short and
connect directly to the receiving gate. Internal circuitry buffers
the outputs of the ADC through a resistor network to eliminate
the need to externally isolate the device from the receiving gate.
EVALUATION BOARD
The AD13465 evaluation board (Figure 9) is designed to
provide optimal performance for evaluation of the AD13465
analog-to-digital converter. The board encompasses everything
needed to ensure the highest level of performance for evaluating
the AD13465. The board requires an analog input signal, encode
clock, and power supply inputs. The clock is buffered on-board
to provide clocks for the latches. The digital outputs and out
clocks are available at the standard 40-pin connectors J1 and J2.
Power to the analog supply pins is connected via banana jacks.
The analog supply powers the associated components and
the analog section of the AD13465. The digital outputs of the
AD13465 are powered via banana jacks with 3.3 V. Contact the
factory if additional layout or applications assistance is required.
Figure 9. Evaluation Board Mechanical Layout
REV. 0
–11–
AD13465
Bill of Materials List for Evaluation Board
Qty
Component Name
Ref/Des
2
1
2
10
2
4
6
74CLX16373MTD
AD13465AZ
ADP3330
BJACK
BRES0805
BRES0805
RES2
36
RES2
28
CAP2
2
2
6
4
2
8
CAP2
H40DM
IND2
MC10EL16
MC100ELT23
POLCAP2
4
12
4
4
1
RES2
SMA
Stand-Off
Screws
PCB
U7, U8
U1
U5, U6
BJ1-BJ10
R41, R53
R38, R39, R55, R56
R1, R2, R5, R7, R8
R54
R3, R4, R6, R9
R12–R15, R19–R28,
R31–R36, R37,
R42–R46, R51, R52
C1, C2, C5–C10,
C12, C16–C18
C20–C26, C28
C30–C38
C13, C27
J1, J2
L1–L6
U2, U3, U9, U11
U4, U10
C3, C4, C11, C14,
C15, C19, C29, C30
R47–R50
J3–J14
Value
Description
Manufacturing Part No.
25 Ω
33 kΩ
50 Ω
Latch
AD13465AZ
Regulator
Banana Jacks
0805 SM Resistor
0805 SM Resistor
0805 SM Resistor
74LCX1673MTD (Fairchild)
AD13465AZ
ADP3330ART-3.3RL7
108-0740-001 (Johnson Components)
EFJ-6GEYJ240V
EFJ-6GEYJ333V
EFJ-6GEYJ333V
100 Ω
0805 SM Resistor
EFJ-6GEYJ333V
0.1 µF
0805 SM Resistor
GRM 40X7R104K025BL
0.47 µF
0805 SM Resistor
2 × 20 40-Pin Male Connector
SM Inductor
Clock Drivers
ECL/TTL Clock Drivers
Tantalum Polar Caps
VJ1206U474MFXMB
TSW-120-08-G-D
2743019447
MC1016EP16D
SY100ELT23L
T491C106M016A57280
0805 SM Resistor
SMA Connectors
Stand-Off
Screws (Stand-Off)
AD13465 Eval Board (Rev B)
ERJ-6GEY OR 00V
142-0701-201
313-2477-016 (Johnson Components)
MPMS 004 0005 PH (Building Fasteners)
GS03361
47 Ω
10 µF
0Ω
–12–
REV. 0
AD13465
J13
SMA
E68
AGNDA
J9
SMA
J6
SMA
E67
AGNDB
E66
J8
SMA
LIDA
J3
SMA
E50
E83
E81
E79
E78
62
61
AGNDB
AMP IN B 2
AMP OUT B
AMP IN B 1
63
64 E84
B+IN
65 E82
B–IN
66 E80
67
AGNDB
68
AGNDB
1
SHIELD
AGNDA
AGNDA
2
E76
E75
3
E73
AMP OUT A
A–IN
7
8
D12B
D11B
D3A
D10B
DRAOUT
DGNDB
DGNDB
–5VAB
C33
0.1␮F
AGNDB
+5VAB
C17
C38
0.1␮F
0.1␮F
AGNDB
59
58
57
56
55
54
AGNDB
ENCB
ENCB
AGNDB
AGNDB
OUT 3.3VDB
53
52
51
50
49
48
47
46
45
44
C18
0.1␮F
D13B
C37
0.1␮F
D12B
D11B
DGNDB
D10B
D9B
D8B
D7B
D6B
DGNDB
43
D5B
42
D6B
60
DGNDB
D4B
D5B
D3B
41
D3B
40
39
D2B
D1B
38
37
DRBOUT
D0B
DGNDA
36
DGNDA
35
D7A
D4B
D7B
D2B
D6A
D1B
D8B
D0B(LSBB)
D9B
D5A
SHIELD
D4A
DRAOUT
26
D1A
27
DGNDA
25
D13B(MSB)
D2A
D13A(MSBA)
D7A
24
AD13465
D0A(LSB)
34
D6A
23
+3.3VDB
D13A
D5A
22
U1
+3VDA
D12A
D4A
21
AGNDB
33
D3A
AGNDA
D12A
DGNDA
20
ENCB
D11A
D1A
D2A
19
–5.2VAB
ENCA
32
D0A
18
AGNDB
ENCBB
D11A
17
C10
0.1␮F
AGNDB
ENCAB
D9A
C36
0.1␮F
16
AGNDB
AGNDB
AGNDB
30
AGNDA
OUT 3.3VDA
15
E86
AGNDA
D9A
ENCA
AGNDA
AGNDB
E52
E85
+5VAB
D8A
ENCA
14
AGNDB
J7
SMA
E54
+5VAA
29
AGNDA
13
–5VAA
D8A
12
DGNDA
11
AGNDA
28
AGNDA
10
AMP IN A 1
AGNDA
–5VAA
C9
0.1␮F
AGNDA
+5VAA
C34
C35
0.1␮F
0.1␮F
AMP IN A 2
AGNDA
9
AGNDA
4 E77
6 E72
AGNDA
E70
A+IN
E49
E69
D10A
AGNDA
5 E74
E71
E53
E51
31
J4
SMA
D10A
AGNDA
J14
SMA
DRBOUT
E56
E55
LIDB
E65
E48
DGNDA
BJ10
1
C29
10␮F
L1
U7
C62
0.1␮F
DGNDB
+3VAA
47⍀
ⴞ20% @100MHz
BJ6
47⍀
ⴞ20%
@100MHz
+3VDA
E40
DUT 3.3VDA
1
C3
10␮F
–5VAA
47⍀
BJ2 ⴞ20%@100MHz
+5VAA
L3
U1
C20
0.1␮F
–5VAA
L5
U1
C32
0.1␮F
AGNDA
AGNDA
AGNDA
1
C11
10␮F
AGNDA
DGNDA
47⍀
ⴞ20%
@100MHz
+3VDB
BJ9
1
C30
10␮F
+5VAB
47⍀
ⴞ20%@100MHz
BJ5
DUT 3.3VDB
U8
C16
0.1␮F
DGNDB
L2
1
C4
10␮F
AGNDB
–5VAB
47⍀
ⴞ20%@100MHz
BJ1
+5VAB
L4
U1
C21
0.1␮F
AGNDB
Figure 10a. Evaluation Board
REV. 0
–13–
1
C19
10␮F
AGNDB
–5VAB
L6
U1
C31
0.1␮F
AGNDB
AD13465
U8
25
26
R48
0⍀
DGNDA
(LSB) D0A
DGNDA
D1A
DUT 3.3VDA
D2A
D3A
DGNDA
D4A
D5A
D6A
D7A
DGNDA
D8A
D9A
DUT 3.3VDA
D10A
D11A
DGNDA
D12A
(MSB) D13A
R7
50⍀
27
28
LE2
OE2
115
O15
114
O14
GND GND
113
29
112
30
VCC
31
111
32
110
33
GND
34
19
35
18
36
17
37
16
38
GND
39
15
40
14
41
VCC
42
13
43
12
44
GND
45
11
46
10
47
LE1
48
24
DGNDA
R17, DNI
23
22
21
O13
20
O12
19
VCC
18
O11
17
O10
16
GND
15
O9
14
O8
13
O7
12
O6
11
GND
10
O5
9
O4
8
VCC
7
O3
6
O2
5
GND
4
O1
3
O0
2
OE1
1
R18, DNI
H40DM
J1
F0A
F1A
R40, DNI
R44, DNI
DGNDA
B0A (LSB)
B1A
R14, 100⍀
R13, 100⍀
R12, 100⍀
DGNDA
B2A
B3A
R46, 100⍀
R15, 100⍀
R24, 100⍀
R23, 100⍀
B4A
B5A
B6A
B7A
B8A
B9A
DUT 3.3VDA
R22, 100⍀
40
39
38
37
36
35
7
8
9
R5
B6A
50⍀
E61
10
11
E59
E60
12
B5A
13
B4A
14
B3A
15
B2A
16
B1A
17
(LSB) B0A 18
F1A 19
F0A
20
DGNDA
34
33
32
31
30
29
(MSB) B13A
B12A
C15
10␮F
B11A
B10A
B9A
DGNDA
B8A
B7A
DUT 3.3VDA
R45, 100⍀
1
2
3
4
5
6
3.3VDA
DGNDA
BUFLATA
DRAOUT
R47
0⍀
B10A
B11A
28
27
26
25
24
23
22
21
R21, 100⍀
DGNDA
R20, 100⍀
R19, 100⍀
DGNDA
B12A
B13A (MSB)
DGNDA
LATCHA
74LCX16374
E58
U7
25
26
R50
0⍀
DGNDB
(LSB) D0B
DGNDB
D1B
DUT 3.3VDB
D2B
D3B
DGNDB
D4B
D5B
D6B
D7B
DGNDB
D8B
D9B
DUT 3.3VDB
D10B
D11B
DGNDB
D12B
(MSB) D13B
R8
50⍀
27
28
LE2
OE2
115
O15
114
O14
GND GND
113
29
112
30
VCC
31
111
32
110
33
GND
34
19
35
18
36
17
37
16
38
GND
39
15
40
14
41
VCC
42
13
43
12
44
GND
45
11
46
10
47
LE1
48
LATCHB
E57
24
DGNDB
R10, DNI
23
22
21
O13
20
O12
19
VCC
18
O11
17
O10
16
GND
15
O9
14
O8
13
O7
12
O6
11
GND
10
O5
9
O4
8
VCC
7
O3
6
O2
5
GND
4
O1
3
O0
2
OE1
1
H40DN
J2
R11, DNI
F0B
F1B
3.3VDB
DGNDB
R30, DNI
R29, DNI
B0B (LSB)
B1B
DUT 3.3VDB
R28, 100⍀
DGNDB
R27, 100⍀
R26, 100⍀
R12, 100⍀
R9, 100⍀
R25, 100⍀
DGNDB
R36, 100⍀
R35, 100⍀
B2B
B3B
B4B
B5B
B6B
B7B
B8B
B9B
DUT 3.3VDB
R34, 100⍀
R33, 100⍀
DGNDB
R32, 100⍀
R31, 100⍀
(MSB) B13B
B12B
C14
10␮F
B11B
B10B
B9B
DGNDB
B10B
B11B
B12B
R2
50⍀
E64
E63
B8B
B7B
B6B
E62
BUFLATB
DRAOUT
R49
0⍀
B5B
B4B
B3B
B2B
B1B
(LSB) B0B
F1B
F0B
DGNDB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
DGNDB
B13B (MSB)
DGNDB
74LCX16374
Figure 10b. Evaluation Board
–14–
REV. 0
AD13465
5
NR
3
ERR
1
OUT
U5
IN
+5VAA
5
ADP3330
SD
GND
4
AGNDA
J5
ENCODE
C1
SMA
0.1␮F
AGNDA
R1
50⍀
AGNDA
R42
100⍀
C13
0.47␮F
1
2
J12
SMA
R41
25⍀
AGNDA
D
3 DB
4
VBB
C2
0.1␮F
8
VCC
NC
Q
U2
C7
0.1␮F
3.3VA
7
BJ4
ENCA
5
VEE
AGNDB
1
ENCA
6
QB
BJ3
R43
100⍀
MC10EL16
NC = NO CONNECT AGNDA
AGNDA
1
C8
0.1␮F
BJ7
DGNDB
1
DGNDB
R56
33k⍀
DGNDA
R55
33k⍀
AGNDA
AGNDA
C6
0.47␮F
NC
8
VCC
R3
100⍀
3.3VDA
2
7
D
Q
U3
6
3 DB
QB
4
5
VBB
VEE
1
2
3
R4
100⍀
MC10EL16
NC = NO CONNECT DGNDA
4
DGNDA
NC
VCC
D
Q0
U4
Q1
DB
VBB
VEE
8
DGNDA
E15
E7
+3.3VDA
LATCHA
E23
7
6
E19
BUFLATA
5
DGNDA
NC = NO CONNECT
NR
ERR
OUT
5
DGNDA
1
GND
4
AGNDB
J10
ENCODE
SMA
AGNDB
C22
0.1␮F
R54
50⍀
AGNDB
2
J11
SMA
3
C23
0.1␮F
VCC
NC
D
U11
DB
QB
4 VBB
R53
25⍀
Q
VEE
8
R52
100⍀
C24
0.1␮F
3.3VB
7
ENCB
5
R51
100⍀
1
2
NC
D
3 DB
4
VBB
VCC
U9
Q
QB
VEE
8
7
DGNDB
C26
0.1␮F
R37
100⍀
6
1
2
R6
100⍀
3
4
MC10EL16
DGNDB
NC = NO CONNECT
DGNDB
NC
D
VCC
U10
DB
VBB
Q0
Q1
VEE
–15–
8
3.3VDA
7
6
5
MC100EPT23
NC = NO CONNECT DGNDB
Figure 10c. Evaluation Board
REV. 0
AGNDA
E38
E29
E1
E36
E14
E45
E3
E37
E30
E2
E35
E13
E46
E4
SO1
SO2
SO3
SO4
SO5
SO6
DGNDB
DGNDB
3.3VDB
5
C28
0.1␮F
AGNDA
R38
33k⍀
C25
0.47␮F
DGNDB
R39
33k⍀
DGNDA
ENCB
6
MC10EL16
NC = NO CONNECT AGNDB
AGNDB
E18
E28
E26
E20
E31
E43
E41
E9
E34
E5
AGNDB
C27
0.47␮F
1
DGNDB
E17
E27
E25
E21
E32
E44
E42
E10
E33
E6
U6
SD
E8
E47
DGNDA
ADP3330
IN
+5VAB
E16
E12
DGNDB
E11
E39
MC100EPT23
5
3
DGNDA
1
DGND
C5
0.47␮F
AGNDA
1
BJ8
LATCHB
E24
E22
BUFLATB
AGNDB
AD13465
Figure 11a. Top Silk
Figure 11b. Top Layer
–16–
REV. 0
AD13465
Figure 11c. GND1
Figure 11d. GND2
REV. 0
–17–
AD13465
Figure 11e. Bottom Silk
Figure 11f. Bottom Layer
–18–
REV. 0
AD13465
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
68-Lead Ceramic Leaded Chip Carrier
(ES-68C)
0.010 (0.25)
0.008 (0.20)
0.007 (0.18)
0.235 (5.97)
MAX
0.960 (24.38)
0.950 (24.13) SQ
0.940 (23.88)
60
44
61
1.070
(27.18)
MIN
43
PIN 1
0.800
(20.32)
BSC
1.190 (30.23)
1.180 (29.97) SQ
1.170 (29.72)
TOP VIEW
(PINS DOWN)
9
27
10
0.060 (1.52)
0.050 (1.27)
0.040 (1.02)
26
DETAIL A
0.055 (1.40)
0.050 (1.27)
0.045 (1.14)
0.175 (4.45)
MAX
0.020 (0.508)
0.017 (0.432)
0.014 (0.356)
0.010 (0.254)
30ⴗ
0.050 (1.27)
0.020 (0.508)
DETAIL A
ROTATED 90ⴗ CCW
REV. 0
–19–
TOE DOWN
ANGLE
0–8 DEGREES
AD13465
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
C01973–2.5–4/01(0)
68-Lead Ceramic Leaded Chip Carrier with Nonconductive Tie-Bar
(ES-68C)
0.960 (24.38)
0.950 (24.13) SQ
0.940 (23.88)
0.350
(8.89)
TYP
0.015 (0.3)
ⴛ 45ⴗ
3 PLS
PIN 1
2.000
(8.89)
TYP
0.055 (1.40)
0.050 (1.27)
0.045 (1.14)
TOP VIEW
(PINS DOWN)
0.020 (0.508)
0.017 (0.432)
0.014 (0.356)
0.040 (1.02)
ⴛ 45ⴗ
0.040 (1.02) R
TYP
0.800 (20.32)
BSC
0.175 (4.45)
MAX
0.235 (5.97)
MAX
DETAIL A
0.010 (0.25)
0.008 (0.20)
0.007 (0.18)
0.010 (0.254)
30ⴗ
0.050 (1.27)
0.020 (0.508)
PRINTED IN U.S.A.
DETAIL A
–20–
REV. 0
Similar pages