AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Description Pin Assignments NEW PRODUCT The AH5795 is a single chip solution for driving single-coil brushless direct current (BLDC) fans and motors. The integrated full-bridge driver output stage uses soft switching to minimize audible switching noise and electromagnetic interference (EMI) providing a low noise solution. (Top View) Motor speed can be controlled by either changing the duty ratio of the PWM signal at the PWM pin or by varying the supply voltage at Vdd pin. FG 1 6 PWM Vss 2 5 Vdd O2 3 4 O1 To help protect the motor coil, the AH5795 provides Rotor Lock Protection which shuts down the output drive if rotor lock is detected. The device automatically re-starts when the rotor lock is removed. Over temperature shutdown provides thermal protection for the device. TSOT23-6 (Top View) A Tachometer output is provided by open-drain Frequency Generator (FG) Pin which allows external interface to monitor motor rotation or speed. The FG output is the magnetic change frequency. PWM 1 6 FG Vdd 2 5 O2 O1 3 4 Vss The AH5795 is available in space saving and low profile TSOT23-6 and DFN2020C-6 packages. DFN2020C-6 Features • • • • • • • • • • • • Supports single-coil full-wave BLDC fan drivers Built-in Hall sensor and input amplifier Operating voltage: 1.8V to 6V Speed control methods o Vdd voltage speed control (PWM pin tied to Vdd) o PWM signal speed control via PWM pin Soft switching for low noise DC fan motor applications Rotor Lock Protection (Lock detection, output shutdown and automatic re-start) Toff clear when PWM is low for greater than 65ms Thermal protection Tachometer (FG) output No external timing capacitor - Reduces the numbers of external components required Low profile package: TSOT23-6 and DFN2020C-6 “Green” Molding Compound (No Br, Sb) (Note 1) Notes: Applications • • • • 3.3V / 5V BLDC Cooling Fans Netbook/ Notebook BLDC fans Instruments cooling fans Low Voltage/ Low Power BLDC Motors 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. AH5795 Document number: DS35277 Rev. 1 - 2 1 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Typical Application Circuit SYSTEM POWER D1 C1 10Kohm Dz NEW PRODUCT Vdd PWM PWM signal for speed control FG AH5795 FG O1 O2 Vss Pin Descriptions Pin Name Vdd VSS O1 O2 PWM FG Notes: Description Power supply pin Ground pin Output driving & sinking pin Output driving & sinking pin PWM signal input pin for speed control Frequency Generator (Note 2) 2. The FG output is the same as the magnetic change frequency. AH5795 Document number: DS35277 Rev. 1 - 2 2 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Functional Block Diagram (Note 3) NEW PRODUCT Vdd Power Lock Detect, Shutdown and Automatic Re-Start FG Frequency Generator O1 PWM Hall Sensor AMP Logic Block Vss Notes: Soft Switching Control Full Bridge Driver O2 3. The AH5795 has an open-drain tachometer FG output that follows the magnetic change frequency. Typically a pull-up resistor of 10KΩ is recommended from FG pin to the supply voltage. AH5795 Document number: DS35277 Rev. 1 - 2 3 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Absolute Maximum Ratings (TA = 25°C, unless otherwise noted, Note 4) Symbol Vdd IO(PEAK) Characteristics Supply voltage Maximum Output Current (Peak) NEW PRODUCT TSOT23-6 PD TST Notes: Unit 7 V 1000mA mA 650 Power Dissipation mW DFN2020C-6 780 (Note 5) Storage Temperature Range ESD HBM Values o -65 ~ 150 Human Body Model (HBM) ESD Protection 4 C kV 4. Stresses greater than the 'Absolute Maximum Ratings' specified above, may cause permanent damage to the device. These are stress ratings only; functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be affected by exposure to absolute maximum rating conditions for extended periods of time 5. DFN2020C-6 exposed pad soldered to minimum recommended landing pads (see Package Outline Dimension section) on a two-layer 2oz. copper FR4 PCB (1.6mm thickness) with no thermal vias in exposed PADs or any copper flood connecting to the landing pattern of the exposed pad. Recommended Operating Conditions (TA = 25°C) Symbol VDD TA Parameter Supply Voltage Operating Ambient Temperature Range Conditions Operating Operating Min 1.8 -40 Max 6.0 105 Unit V o C Electrical Characteristics (TA = 25°C, VDD = 5V) Symbol IDD Characteristics Supply Current VOH Output Voltage High VOL Output Voltage Low Voh+Vol TSW ILEAK VFGOL TON RDR VPWMH VPWML IPWMH IPWMH FPWM DPWM_MIN Tj_SDN_TH Tj_SDN_HYST Output voltage of N- and PMOS combined Output Switching Slope Duration FG Output Leakage Current FG Output Voltage Low On Time Duty Ratio PWM Input H Level PWM Input L Level PWM Input current H Level PWM Input current L Level PWM Input Frequency Output minimum duty ratio IC junction temperature thermal shutdown threshold IC junction temperature thermal shutdown hysteresis AH5795 Document number: DS35277 Rev. 1 - 2 Conditions No Load IOUT = 300mA IOUT = 500mA IOUT = 300mA IOUT = 500mA IOUT = 300mA IOUT = 500mA 17Ω load on out1/out2 IFG = 5mA TOFF / TON PWM=Vdd PWM=GND Motor rotating; 4 of 13 www.diodes.com Min 4.70 4.5 - 350 0.5 Vdd 0 0.02 10% Typ. 2.2 4.88 4.8 0.12 0.2 0.3 0.5 200 500 10 0 -10 - Max 0.3 0.5 0.6 5 0.4 650 Vdd 0.14 Vdd 50 100 Unit mA V V V V V V μs μA V ms V V uA uA KHz % 175 o C 25 o C August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Magnetic Characteristics (TA = 25°C, Vdd = 1.8V~6V, Note 6) (1mT = 10 G) Parameter Min Typ. Max Bop Operate Point 10 25 50 Brp Release Point -50 -25 -10 Bhy Hysteresis - 50 - Notes: Unit Gauss 6. Magnetic characteristics may vary with supply voltage, operating temperature and after soldering. Operating Characteristics O1 O2 VOH VOH RP OFF ON OP Output Voltage in Volts Output Voltage in Volts NEW PRODUCT Symbol VOL Brp 0 OFF OP RP ON VOL Bop Brp Magnetic Flux Density in Gauss 0 Magnetic Flux Density in Gauss S N Marking side Marking side N S (DFN2020C-6) (TSOT23-6) AH5795 Document number: DS35277 Rev. 1 - 2 Bop 5 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Operating Characteristics (cont. Note 7, 8, 9 and 10) NEW PRODUCT Magentic S N O2 O1 Ton FG Toff Mechanical lock Normal spinning motor locked detected “Re-start spinning” motor locked cleared Truth Table O1 L H L Notes: O2 H L L PWM H H L FG L H X (Note 10) 7. In “Normal spinning, the FG changes its state at each edge of O1. 8. When the motor locks with South pole at the Hall element, O2 is kept on “L” and O1 is a clock with Ton/Toff ratio. When motor locks with North pole at the Hall element, O1 is kept on “L”, O2 is a clock with Ton/Toff ratio. 9. When “Re-start spinning” occurs, the motor speed ramps up to the “Normal Spinning” speed from zero. Speed ramp-up profile depends on motor characteristics. 10. X: H or L depends on magnetic pole north or South AH5795 Document number: DS35277 Rev. 1 - 2 6 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Application Note DC Supply voltage speed control Motor speed can be controlled by varying the Vdd supply voltage while PWM pin is tied to Vdd pin. NEW PRODUCT For example, with 5V nominal motor, changing supply voltage between 5V to 1.8V, speed can be reduced from 100% to 36% typically. PWM speed control Motor speed can also be adjusted by applying a PWM speed control signal into the PWM pin while keeping the Vdd pin at nominal motor voltage. The motor speed is proportional to the PWM signal duty. For example, with 5V nominal motor, Vdd pin is maintained at 5V typical while varying the PWM control signal duty to adjust the motor speed linearly. Figure below shows the output O1 and O2 in relation to PWM speed control signal at PWM pin. Frequency of PWM speed control signal can be between 15Hz to 50kHz. Recommended typical PWM signal frequency is 25kHz to keep switching frequency away from audible band. If PWM signal level at PWM pin stays low for longer than 65ms typical, the outputs are disabled. Depending on the motor design and its inertia, minimum start-up PWM duty required can be typically between 30% - 40% while minimum running PWM duty can be down to 20%-25% typical. If voltage at Vdd is lower than the nominal motor voltage, both start-up PWM duty and minimum running PWM duty required will be higher. AH5795 Document number: DS35277 Rev. 1 - 2 7 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Application Note (cont.) Rotor lock Toff and PWM signal NEW PRODUCT When PWM signal input at PWM pin is low for longer than 65ms, internal rotor lock protection Toff is cleared. This allows the device to enter motor start Ton time on the next PWM high signal PWM 65ms (max) Rotor lock protection (internal signal) Enabled Disabled (Toff cleared) Enabled Soft Switching AH5795 uses soft switching of the motor coil current during commutation for to minimize audible switching noise and electromagnetic interference (EMI) to provide a low noise solution. Vdd Vout 1 Vout 2 Vss 200µs typ. AH5795 Document number: DS35277 Rev. 1 - 2 8 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Thermal Performance Characteristics (1) TSOT23-6 NEW PRODUCT TA (°C) 25 50 60 70 75 80 PD (mW) 651 521 469 417 391 365 339 313 286 260 TA (°C) 105 110 115 120 125 130 135 140 145 150 PD (mW) 234 208 182 156 130 104 78 52 26 0 PD (mW) 85 90 95 100 Power Dissipation Curve 700 650 600 500 400 300 200 100 0 0 -40 25 50 75 100 105 125 150 TA (°C) (2) DFN2020C-6 (Note 11) TA (°C) 25 50 60 70 75 80 85 90 95 100 PD (mW) 781 625 563 500 469 438 406 375 344 313 TA (°C) 105 110 115 120 125 130 135 140 145 150 PD (mW) 281 250 219 188 156 125 94 63 31 0 PD (mW) Power Dissipation Curve 900 800 700 600 500 400 300 200 100 0 0 -40 25 50 75 100 105 125 150 TA (°C) Notes: 11. DFN2020C-6 exposed pad soldered to minimum recommended landing pads (see Package Outline Dimension section) on a two-layer 2oz. copper FR4 PCB (1.6mm thickness) with no thermal vias in exposed PADs or any copper flood connecting to the landing pattern of the exposed pad. AH5795 Document number: DS35277 Rev. 1 - 2 9 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Ordering information Device Packing WU : TSOT23-6 FDC : DFN2020C-6 7 : Tape & Reel 7” Tape and Reel Part Number Suffix Package Code Packaging (Note 12 & 13) Quantity WU FDC TSOT23-6 DFN2020C-6 3000/Tape & Reel 3000/Tape & Reel AH5795-WU-7 AH5795-FDC-7 Notes: Package -7 -7 12. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at http://www.diodes.com/datasheets/ap02001.pdf 13. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html Marking Information (1) TSOT23-6 (Top View) 5 6 4 7 NEW PRODUCT AH 5795 - XXX - 7 XX : Identification code Y : Year 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : Internal code XX Y W X 1 2 3 Part Number Package Identification Code AH5795-WU-7 TSOT23-6 J5 (2) DFN2020C-6 ( Top View ) XX YWX XX : Identification Code Y : Year : 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : Internal code Part Number Package Identification Code AH5795-FDC-7 DFN2020C-6 J5 AH5795 Document number: DS35277 Rev. 1 - 2 10 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Package Outline Dimensions (All Dimensions in mm) NEW PRODUCT (1) Package type: TSOT23-6 (2) Package Type: DFN2020C-6 0.6±0.1 0.43mon. 1.0±0.1 Pin#1 0.15max. 0.10 C B 2x- Seating plane 6x-0.37 C A Hall Sensor 0.25/0.35 15 0.86/1.06 1.95/2.075 R 0. 1.95/2.075 1.55/1.75 (Active area depth) 6x-0.45 0.25 A Pin#1 ID 2x 0/0.05 0.08 C 0.9 0.57/0.63 Hall Sensor locator 0.65 1 R0 . 1.59 0.25 B 0.65nom. 0.25/0.35 0.10 M C A B Land Pattern Recommendation (Unit:mm) Top View Bottom View AH5795 Document number: DS35277 Rev. 1 - 2 11 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER Taping Orientation NEW PRODUCT For DFN2020C-6 Notes: 14. The taping orientation of the other package type can be found on our website at http://www.diodes.com/datasheets/ap02007.pdf. AH5795 Document number: DS35277 Rev. 1 - 2 12 of 13 www.diodes.com August 2011 © Diodes Incorporated AH5795 SINGLE PHASE HALL EFFECT LATCH SMART FAN MOTOR CONTROLLER IMPORTANT NOTICE NEW PRODUCT DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2011, Diodes Incorporated www.diodes.com AH5795 Document number: DS35277 Rev. 1 - 2 13 of 13 www.diodes.com August 2011 © Diodes Incorporated