1.6x0.8mm SMD CHIP LED LAMP Part Number: APHK1608SEC SUPER BRIGHT ORANGE Features Description ●1.6mmx0.8mm SMT LED, 0.7mm THICKNESS. The Super Bright Orange device is made with DH ●LOW POWER CONSUMPTION. InGaAlP (on GaAs substrate) light emitting diode chip. ●WIDE VIEWING ANGLE. ●IDEAL FOR BACK LIGHT AND INDICATOR. ●VARIOUS COLORS AND LENS TYPES AVAILABLE. ●MOISTURE SENSITIVITY LEVEL : LEVEL 4. ●PACKAGE : 2000PCS / REEL. ●RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3.Specifications are subject to change without notice. SPEC NO: DSAD1113 REV NO: V.4 DATE: NOV/06/2006 PAGE: 1 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000046 Selection Guide Dice Part No. APHK1608SEC Iv (mcd) [2] @ 20mA Lens Type SUPER BRIGHT ORANGE (InGaAlP) WATER CLEAR Viewing Angle [1] Min. Typ. 2 θ 1/2 110 280 90° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Super Bright Orange λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 610 nm IF=20mA Super Bright Orange 601 nm IF=20mA Spectral Line Half-width Super Bright Orange 29 nm IF=20mA C Capacitance Super Bright Orange 30 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Orange 2.0 2.5 V IF=20mA IR Reverse Current Super Bright Orange 10 uA VR= 5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Super Bright Orange Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 195 mA Reverse Voltage 5 V Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1113 REV NO: V.4 DATE: NOV/06/2006 PAGE: 2 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000046 Super Bright Orange APHK1608SEC SPEC NO: DSAD1113 REV NO: V.4 DATE: NOV/06/2006 PAGE: 3 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000046 APHK1608SEC Recommended Soldering Pattern (Units: mm ; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAD1113 REV NO: V.4 DATE: NOV/06/2006 PAGE: 4 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000046 PACKING & LABEL SPECIFICATIONS APHK1608SEC SPEC NO: DSAD1113 REV NO: V.4 DATE: NOV/06/2006 PAGE: 5 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000046