AH202 The Communications Edge TM Product Information 1W High Linearity Amplifier Product Features Product Description x 50 – 2200 MHz The AH202 is a 1-Watt driver amplifier that offers excellent dynamic range in a low-cost, lead-free/RoHScompliant 6x6 mm 28-pin QFN surface-mount package. This device provides its optimum P1dB and OIP3 performance when biased at + 11 V; It can also be biased as low as +9 V for lower power applications. x +30 dBm P1dB x +47 dBm Output IP3 x 17 dB Gain @ 900 MHz x MTTF >100 Years x Single Positive Supply x Internally Matched x Lead-free/RoHS-compliant 6x6mm QFN SMT package Applications x Mobile Infrastructure x CATV / DBS x Optimal for VHF / UHF broadband applications x Defense / Homeland Security The backside metalization provides excellent thermal dissipation while allowing visible evidence of solder reflow across the bottom of the package on a SMT board. Superior thermal design allows the product an MTTF of over 100 years at a mounting temperature of +85º C. All devices are 100% RF & DC tested. The product is targeted for use as a driver amplifier for wireless infrastructure or CATV applications where high linearity and medium power is required. 27 26 25 24 23 22 21 2 20 RF IN 3 19 RF OUT 4 18 5 17 6 16 N/C 7 15 8 9 10 Function Input No Connect Output/Bias No Connect or Ground 11 12 13 14 Pin No. 3 7 19 All other pins Backside Paddle Typical Performance (4) Units Min Operational Bandwidth Test Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 (2) Noise Figure IS-95 Channel Power (3) MHz MHz dB dB dB dBm dBm dB 50 Operating Current Range Supply Voltage mA V @ -45dBc ACPR 28 1 Ground Specifications (1) Parameters Functional Diagram Typ 14 +29 +45 dBm Max Parameters 2200 800 17 20 18 +30 +47 2.5 Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 Noise Figure IS-95 Channel Power (3) +24 WCDMA Channel Power(5) 330 +11 390 1. Test conditions unless otherwise noted: 25ºC, Vdd = 11 V in a 502. 3OIP measured with two tones at an output power of +10 dBm/tone separated by 10 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. IS-95, 9 Channels Forward, Pk/Avg Ratio = 11.5 dB at a .001% probability, ±885 kHz offset, 30 kHz bandwidth, Channel BW = 1.23 MHz. Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature DC Voltage RF Input Power (continuous) Maximum Junction Temperature Units Typical MHz dB dB dB dBm dBm dB 900 17 20 18 +30 +47 2.8 1900 15 17 10 +29.7 +46 3.8 2140 15 8 13 +29.4 +45.5 4.8 @ -45dBc ACPR dBm +24 +23 - @ -45dBc ACLR dBm - - +20.5 Supply Bias +11 V @ 330 mA 4. Data reflects performance of a typical AH202 in an application circuit including associated circuit board and passive component losses. 5. 3GPP W-CDMA, Test Model 1, +32 DPCH, Pk/Avg Ratio = 8.5 dB at a 0.01% probability, ±5 MHz offset, Integrated Channel BW = 3.84 MHz. Ordering Information Rating -40 to +85 qC -55 to +125 qC +13 V +16 dBm +220 qC Part No. Description AH202-F 1W High Linearity Amplifier AH202-PCB900 AH202-PCB1900 AH202-PCB2140 900 MHz Evaluation Board 1900 MHz Evaluation Board 2140 MHz Evaluation Board (lead-free/RoHS-compliant 6x6mm QFN package) Operation of this device above any of these parameters may cause permanent damage. Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com Page 1 of 9 August 2005 Rev 2 AH202 The Communications Edge TM Product Information 1W High Linearity Amplifier Typical Device Data S-parameters (VDS = +11 V, IDS P$XQPDWFKHGGHYLFHLQD V\VWHP x Measurements are shown for an unmatched packaged device with the data being de-embedded to the device leads. Gain 20 Return Losses 0 19 -5 18 S11 -10 16 (dB) S21 (dB) 17 15 14 S22 -15 -20 13 12 -25 11 -30 10 0 0.5 1 1.5 Frequency (GHz) 2 0 2.5 0.5 1 1.5 Frequency (GHz) 2 2.5 S-Parameters (VDS = +11.0V, IDS = 330mA, T = +25qC, unmatched device in a 50 : system) Freq (MHz) S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 50 -17.78 -137.86 18.26 169.32 -21.43 1.41 -15.33 -170.64 100 -18.60 -153.83 18.06 166.20 -21.34 -4.54 -15.51 177.37 200 -17.34 -150.80 18.03 156.86 -21.46 -12.16 -16.27 161.24 400 -14.70 -149.17 17.87 135.75 -21.84 -25.03 -18.57 135.96 600 -11.92 -159.61 17.43 115.76 -22.34 -37.49 -21.38 93.89 800 -10.29 -171.08 16.93 96.20 -22.96 -48.84 -26.07 25.81 1000 -9.20 174.71 16.36 77.49 -23.72 -61.29 -21.37 -47.34 1200 -8.23 160.52 15.90 58.22 -24.54 -73.36 -16.16 -78.06 1400 -7.74 145.06 15.43 40.52 -25.32 -85.56 -12.76 -98.55 1600 -7.43 127.89 15.04 23.04 -26.07 -99.09 -10.27 -114.42 1800 -7.73 108.79 14.82 4.23 -26.69 -115.15 -8.39 -129.46 2000 -8.76 84.28 14.72 -15.48 -26.94 -132.95 -7.17 -144.14 2200 -10.40 43.69 14.59 -38.77 -26.60 -155.57 -6.37 -158.61 2400 -10.57 -24.74 14.42 -65.43 -25.80 176.52 -6.14 -172.06 2600 -6.72 -90.87 13.29 -97.06 -25.02 143.13 -6.69 176.96 2800 -3.60 -136.82 10.89 -128.44 -24.82 111.82 -7.11 173.14 3000 -1.91 -167.99 7.61 -154.46 -25.13 87.68 -6.73 174.58 Application Circuit PC Board Layout Circuit Board Material: .014” Getek ( r=4.2), four layer, 1 oz copper Microstrip line details: width = .026”, spacing = .026” Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com Page 2 of 9 August 2005 Rev 2 AH202 The Communications Edge TM Product Information 1W High Linearity Amplifier Reference Design: 50-800 MHz The AH202 is suitable for applications between 50 – 800 MHz without any requirements for input or output matching. Only bypass and blocking capacitors and an RF bias choke are needed for operation. A user can simply request an AH202-PCB900 Evaluation Board and replace components C1, C2, C3, C6, L1, and L2 to the values shown below to evaluate the device. Frequency S21 – Gain S11 – Input Return Loss S22 – Output Return Loss Output P1dB Output IP3 MHz dB dB dB dBm (+10 dBm / tone, 10 MHz spacing) Supply Bias 50 18 -13 -13 200 17.9 -17 -15 400 600 800 17.5 17.0 16.3 -15 -12.4 -10.3 -17 -22 -28 +30 dBm +47 dB +11 V @ 330 mA + 11V CAP ID=C5 C=1e5 pF CAP ID=C4 (0805) C=1000 pF CAP ID=C1 C=1000 pF PORT P=1 Z=50 Ohm IND ID=L1 L=470 nH RES ID=L2 R=0 Ohm SUBCKT ID=S1 NET="AH202_F" PORT P=2 Z=50 Ohm CAP ID=C2 C=1000 pF Measured Performance 20 15 Magnitude (dB) 10 5 0 -5 -10 -15 -20 -25 DB(|S[1,1]|) DB(|S[2,1]|) DB(|S[2,2]|) -30 0 Notes: 0.2 0.4 0.6 Frequency (GHz) 0.8 1 !" #!$&%('*)+ -,"./02143 5/264#3 7$-8 #!$+9 8 8 7$ 7*:1*143 5/7 #;<5/ $ 5," =?> :57A@4 R=0 removed from the circuit without any effect to the performance. The microstrip line is weakly co-planar. Ground planes around it are not necessary for operation of the AH202. Adequate heat sinking is required for the device. Further mounting instructions are shown in the AH202 datasheet. The RF choke should be a wirewound ceramic type to insure sufficient current carrying capacity. Coilcraft’s 1008 CS series is recommended (part #1008CS-471X_B_). Specifications and information are subject to change without notice WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 e-mail: [email protected] Web site: www.wj.com Page 3 of 9 August 2005 Rev 2 AH202 The Communications Edge TM Product Information 1W High Linearity Amplifier Application Circuit: 900 MHz (AH202-PCB900) + 11V Typical RF Performance at 25qC Frequency S21 - Gain S11 S22 Output P1dB Output IP3 IS-95A Ch. Power 900 MHz 17 dB - 20 dB - 18 dB + 47 dBm + 30 dBm Noise Figure Supply Voltage Supply Current Notes: 1. CAP ID=C4 (0805) C=1000 pF PORT P=1 Z=50 Ohm + 24 dBm @ -45 dBc ACPR CAP ID=C1 C=100 pF 2.8 dB +11 V 330 mA SUBCKT ID=S1 NET="AH202_F" IND ID=L2 L=3.3 nH CAP ID=C3 C=100 pF IND ID=L1 (1008) L=33 nH CAP ID=C2 C=100 pF CAP ID=C6 C=2.7 pF PORT P=2 Z=50 Ohm The amplifier should be connected directly to a +11 V regulator; no dropping resistor is required. If no DC signal is present at the input (pin 1), C1 can be removed. The gate (input pin) is internally grounded in the amplifier. Component sizes are 0603 unless otherwise noted. RF choke L1 should be wirewound ceramic type to insure sufficient current carrying capacity. Coilcraft’s 1008 CS series (part # 1008CS-330X_B) is recommended. C6 is located at silk screen marker “C” on the WJ evaluation board. 2. 3. 4. S-Parameters Noise Figure vs. Frequency Vd = +11.0V, Temp = +25°C 0 5 -5 4 -10 -15 S22 -20 S11 Noise Figure (dB) 20 19 18 S21 17 16 15 14 13 12 11 10 700 S11 & S22 (dB) S21 (dB) CAP ID=C5 (1206) C=100000 pF -25 1100 800 900 1000 Frequency (MHz) 3 2 1 0 700 800 900 1000 Frequency (MHz) OIP3 vs. Pout ACPR vs. Channel Power Vd = +11.0V, Temp = +25°C 900 MHz, IS-95 Ch. Fwd. ± 885KHz offset, 30 KHz Meas. BW -40 55 1100 -45 50 ACPR (dBc) OIP3 (dBm) Vd = 11.0V, Temp = 25°C 45 40 -50 -55 -60 -65 -70 -75 35 5 7 9 11 13 Pout (dBm) 15 15 17 17 19 21 23 Output Channel Power (dBm) 25 Specifications and information are subject to change without notice WJ Communications, Inc B Phone 1-800-WJ1-4401 B FAX: 408-577-6621 B e-mail: [email protected] B Web site: www.wj.com Page 4 of 9 August 2005 Rev 2 AH202 The Communications Edge TM Product Information 1W High Linearity Amplifier Application Circuit: 1900 MHz (AH202-PCB1900) Typical RF Performance at 25qC Frequency S21 - Gain S11 S22 Output P1dB Output IP3 IS-95A Ch. Power 1900 MHz 15 dB - 17 dB - 10 dB + 29.7 dBm + 46 dBm Noise Figure Supply Voltage Supply Current 2. 3. POR T P=1 Z=50 O hm TLIN ID = TL1 Z0=50 O hm EL =31 D eg F0=19 00 M H z C AP ID=L 2 C =2.4 pF 3.8 dB +11 V 330 mA C AP ID= C 2 C =56 pF CAP ID =C 7 C=1 .0 pF POR T P= 2 Z=50 Ohm The amplifier should be connected directly to a +11 V regulator; no dropping resistor is required. Component sizes are 0603 unless otherwise noted. RF choke L1 should be wirewound ceramic type to insure sufficient current carrying capacity. Coilcraft’s 1008 CS series (part # 1008CS-220X_B) is recommended. C7 is located between silk screen markers “6” and “7” on the WJ evaluation board. Noise Figure S-Parameters -5 -10 S22 -15 S11 1800 1900 -20 2000 -25 2200 2100 5 4 3 2 1 0 1700 Frequency (MHz) 55 Vd = +11.0 V, Temp = +25°C 6 0 S21 Noise Figure (dB) 16 15 14 13 12 11 10 9 8 7 6 1700 S11 & S22 (dB) S21 (dB) C AP ID =C3 C = 56 pF IND ID=L 1 (1 008 ) L=2 2 nH SUBC KT ID=S1 N ET ="AH20 2_F" Vd = +11.0V, Temp = +25C 1800 1900 Frequency (MHz) 2000 OIP3 vs. Pout ACPR vs. Channel Power Vd = +11.0 V, Temp = +25°C 1900 MHz., IS-95 Ch. Fwd, ± 885 KHz offset, 30 KHz Meas. BW -40 -45 50 ACPR (dBc) OIP3 (dBm) CAP ID =C5 (12 06 ) C= 1e 5 pF CAP ID=C 4 (0 80 5) C=1 000 pF + 23 dBm @ -45 dBc ACPR Notes: 1. + 1 1V 45 40 -50 -55 -60 -65 -70 35 5 7 9 11 13 15 -75 17 14 Pout (dBm) 16 18 20 22 Output Channel Power (dBm) 24 Specifications and information are subject to change without notice WJ Communications, Inc B Phone 1-800-WJ1-4401 B FAX: 408-577-6621 B e-mail: [email protected] B Web site: www.wj.com Page 5 of 9 August 2005 Rev 2 AH202 The Communications Edge TM Product Information 1W High Linearity Amplifier Reference Design: 1900 MHz using the AH202 in the previously recommended circuit configuration with the AH201 (AH201-PCB1900) Typical RF Performance at 25qC Frequency S21 - Gain S11 S22 Output P1dB Output IP3 IS-95A Ch. Power + 11V 1900 MHz 15 dB - 8 dB - 8 dB + 29.7 dBm + 46 dBm CAP ID=C4 (0805) C=1000 pF CAP ID=C1 C=56 pF PORT P=1 Z=50 Ohm + 23 dBm @ -45 dBc ACPR Noise Figure Supply Voltage Supply Current CAP ID=C5 (1206) C=1e5 pF RES ID=L2 R=0 Ohm SUBCKT ID=S1 NET="AH202_F" TLIN ID=TL1 Z0=50 Ohm EL=31 Deg F0=1900 MHz CAP ID=C6 C=0.5 pF 3.8 dB +11 V 330 mA CAP ID=C3 C=56 pF IND ID=L1 (1008) L=22 nH CAP ID=C2 C=56 pF CAP ID=C7 C=1.0 pF PORT P=2 Z=50 Ohm Notes: 1. The amplifier should be connected directly to a +11 V regulator; no dropping resistor is required. 2. If no DC signal is present at the input (pin 1), C1 can be removed. The gate (input pin) is internally grounded in the amplifier. 3. Component sizes are 0603 unless otherwise noted. RF choke L1 should be wirewound ceramic type to insure sufficient current carrying capacity. Coilcraft’s 1008 CS series (part # 1008CS-220X_B) is recommended. 4. 7 !47 #!$H%('I J,"KLL143 5/:64#3 7$J8 #!$M&* 8 8 7$ 7*(1*143 5 #;I5/ $ 5," =+> (5K@4:$ 7NO#!P4K8 $ #!NQ 64&5 $ 5," SR+ 64#;,**TK/8 8 57S # CEDGF the performance. C6 is located at silk screen marker “ C” and C7 is located between silk screen markers “ 6” and “ 7” on the WJ evaluation board. 5. Noise Figure S-Parameters Vd = +11.0V, Temp = +25C 16 6 0 S21 (dB) S22 14 -10 S11 13 -15 12 1700 1800 1900 Frequency (MHz) S11 & S22 (dB) -5 Noise Figure (dB) S21 15 Vd = 11.0V, Temp = 25°C -20 2000 5 4 3 2 1 0 1700 1800 1900 Frequency (MHz) OIP3 vs. Pout 2000 ACPR vs. Channel Power Vd = +11V, Temp = 25°C 1900 MHz., IS-95 Ch. Fwd, ± 885 KHz offset, 30 KHz Meas. BW -40 55 -45 OIP3 (dBm) ACPR (dBc) 50 45 40 -50 -55 -60 -65 -70 35 -75 5 7 9 11 13 Pout (dBm) 15 17 14 16 18 20 22 Output Channel Power (dBm) 24 Specifications and information are subject to change without notice WJ Communications, Inc B Phone 1-800-WJ1-4401 B FAX: 408-577-6621 B e-mail: [email protected] B Web site: www.wj.com Page 6 of 9 August 2005 Rev 2 AH202 The Communications Edge TM Product Information 1W High Linearity Amplifier Application Circuit: 2140 MHz (AH202-PCB2140) Typical RF Performance at 25qC Frequency S21 - Gain S11 S22 Output P1dB Output IP3 W-CDMA Ch. Power POR T P=1 Z=50 O hm C AP ID =L2 C =2.2 p F C AP ID =C3 C =56 pF IND ID=L 1 (1 008 ) L=2 2 nH SUB C KT ID=S1 N ET ="A H 202_F" TLIN ID =TL1 Z0=50 O hm EL=28 D eg F0=21 40 M H z 4.8 dB +11 V 330 mA Noise Figure Supply Voltage Supply Current Notes: 1. 2. CAP ID=C 4 (0 80 5) C=1 000 pF + 20.5 dBm @ -45 dBc ACLR CA P ID =C5 (12 06 ) C=1e 5 pF + 1 1V 2140 MHz 15 dB - 8 dB - 13 dB + 29.4 dBm + 45.5 dBm C AP ID=C 2 C =56 pF CAP ID =C 7 C=1 .0 pF POR T P=2 Z=50 Ohm The amplifier should be connected directly to a +11 V regulator; no dropping resistor is required. If no DC signal is present at the input (pin 1), C1 can be removed. The gate (input pin) is internally grounded in the amplifier. Component sizes are 0603 unless otherwise noted. RF choke L1 should be wirewound ceramic type to insure sufficient current carrying capacity. Coilcraft’s 1008 CS series (part # 1008CS-220X_B) is recommended. C7 is located between silk screen markers “ 5” and “ 6” on the WJ evaluation board. 3. 4. S-Parameters Noise Figure Vd = +11.0V, Temp = +25°C 16 0 6 -5 5 Vd = + 11V, Temp = 25°C -10 10 -15 S22 8 -20 6 2000 S11 & S22 (dB) S21 (dB) S11 12 Noise Figure (dB) S21 14 3 2 1 0 2000 -25 2300 2100 2200 Frequency (MHz) 4 2100 2200 Frequency (MHz) OIP3 vs. Pout f = 2140MHz, 3GPP W-CDMA, Test Model 1, +32 DPCH, ±5 MHz offset -40 50 ACLR (dBc) OIP3 (dBm) ACLR vs. Channel Power Vd = +11.0 V, Temp = +25°C 55 2300 45 40 35 -45 -50 -55 -60 5 7 9 11 13 15 17 15 16 17 18 19 20 21 Output Channel Power (dBm) Pout (dBm) 22 Specifications and information are subject to change without notice WJ Communications, Inc B Phone 1-800-WJ1-4401 B FAX: 408-577-6621 B e-mail: [email protected] B Web site: www.wj.com Page 7 of 9 August 2005 Rev 2 AH202 The Communications Edge TM Product Information 1W High Linearity Amplifier Reference Design: 2140 MHz using the AH202 in the previously recommended circuit configuration with the AH201 (AH201-PCB2140) Typical RF Performance at 25qC Frequency S21 - Gain S11 S22 Output P1dB Output IP3 W-CDMA Ch. Power PORT P=1 Z=5 0 Ohm CAP ID=C1 C=56 pF RES ID=L2 R=0 Ohm CAP ID=C3 C=56 pF IND ID=L 1 (1008) L=18 nH SUBCKT ID=S1 NET="AH202_F" TLIN ID=TL1 Z0=50 Ohm EL=28 Deg F0=2140 MHz 4.2 dB +11 V 330 mA Supply Current 4. 5. CAP ID=C7 C=1.1 pF PORT P=2 Z=50 Ohm Noise Figure S-parameters Vd = +11V, Temp = +25C -5 S11 -10 14 S22 13 -15 -20 12 11 2000 2100 Noise Figure (dB) S21 15 -25 2300 2200 Vd = + 11V, Temp = 25°C 6 0 S11 & S22 (dB) 16 S21 (dB) CAP ID=C2 C=56 pF The amplifier should be connected directly to a +11 V regulator; no dropping resistor is required. If no DC signal is present at the input (pin 1), C1 can be removed. The gate (input pin) is internally grounded in the amplifier. Component sizes are 0603 unless otherwise noted. RF choke L1 should be wirewound ceramic type to insure sufficient current carrying capacity. Coilcraft’s 1008 CS series (part # 1008CS-180X_B) is recommended. R = 0 VWXYZ[ \!]4V7W ^!_H`(aI[ ZJb"ZY/X2VZcVLd4e Vf/Yg4^e XY7_Jh ^!_MV-X[ h h Y7_ Y7]*W(Vd*d4e [ fVW [ ^;]Of[ _ fb"[ W i-j W(fV7]0k4Y:_ Y7lO^!m*YXKh _ ^!lQW g4Y&f[ _ fb"[ WSn+[ W g4^!b*WV]*oKY/h h Yf7W to the performance. C7 is located between silk screen markers “ 5” and “ 6” on the WJ evaluation board. 3. 5 4 3 2 1 0 2000 Frequency (MHz) 2100 2200 Frequency (MHz) OIP3 vs. Pout 2300 ACLR vs. Channel Power Vd = + 11V, Temp = 25°C 55 f = 2140MHz, 3GPP W-CDMA, Test Model 1, +32 DPCH, ±5 MHz offset -40 50 ACLR (dBc) OIP3 (dBm) CAP ID=C5 (1206) C=1e5 pF CAP ID=C4 (0 805) C=1000 p F + 20.5 dBm @ -45 dBc ACLR Noise Figure Supply Voltage Notes: 1. 2. + 11V 2140 MHz 14.6 dB -7 dB - 7 dB + 29.4 dBm + 45.5 dBm 45 40 -45 -50 -55 -60 35 5 7 9 11 13 Pout (dBm) 15 15 17 16 17 18 19 20 21 Output Channel Power (dBm) 22 Specifications and information are subject to change without notice WJ Communications, Inc U Phone 1-800-WJ1-4401 U FAX: 408-577-6621 U e-mail: [email protected] U Web site: www.wj.com Page 8 of 9 August 2005 Rev 2 AH202 The Communications Edge TM Product Information 1W High Linearity Amplifier AH202 Mechanical Information This package is lead-free/RoHS-compliant. It is compatible with both lead-free (maximum 260qC reflow temperature) and leaded (maximum 245qC reflow temperature) soldering processes. The plating material on the pins is annealed matte tin over copper. Outline Drawing Product Marking The component will be lasermarked with a “ AH202F” product label with an alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part will be located on the website in the “ Application Notes” section. ESD / MSL Information ESD Rating: Value: Test: Standard: Class 1B Passes between 500 and 1000V Human Body Model (HBM) JEDEC Standard JESD22-A114 ESD Rating: Value: Test: Standard: Class III Passes between 500 and 1000V Charged Device Model (CDM) JEDEC Standard JESD22-C101 MSL Rating: Level 2 at +260 p C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Configuration / Land Pattern Functional Pin Layout Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Thermal Specifications Parameter Rating Operating Case Temperature Thermal Resistance, Rth (1) Junction Temperature, Tjc (2) -40 to +85 qC 17.5 qC / W 152 qC Pin 15 16 17 18 19 20 21 22 23 24 25 26 27 28 FUNCTION GND or N/C GND or N/C GND or N/C GND or N/C RF Output GND or N/C GND or N/C GND or N/C GND or N/C GND or N/C GND or N/C GND or N/C GND or N/C GND or N/C Backside paddle is RF and DC ground. Pin 7 is required to be not connected or grounded for the AH202 to be functional. MTTF vs. GND Tab Temperature 100 FUNCTION GND or N/C GND or N/C RF Input GND or N/C GND or N/C GND or N/C No Connect GND or N/C GND or N/C GND or N/C GND or N/C GND or N/C GND or N/C GND or N/C 10 1. The thermal resistance is referenced from the hottest part of the junction to the backside copper paddle. 2. This corresponds to the typical biasing condition of +11V, 350 mA at an 85p C case temperature. A minimum MTTF of 1 million hours is achieved for junction temperatures below 160 p C. 1 0 60 70 80 90 100 Tab Temperature (°C) 110 Specifications and information are subject to change without notice WJ Communications, Inc U Phone 1-800-WJ1-4401 U FAX: 408-577-6621 U e-mail: [email protected] U Web site: www.wj.com Page 9 of 9 August 2005 Rev 2