Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ ■ ■ ■ ■ Änderungen vorbehalten / subject to change without notice Ordering information Unit type ADA600F 2 F 3 -24 4 Recommended Noise Filter NAC-20-472 R ADA ADA 600 1 High voltage pulse noise type : NAP series Low leakage current type : NAM series *The Noise Filter is recommended *to connect with several devices. -O 5 1Series name 2Output wattage 3Universal input 4Output voltage 5Optional G :Low leakage current E :Low leakage current and EMI class A F :with Fan unit(only -24) T :Vertical terminal block J :Connector type C :with Coating R :Remote ON/OFF N1:DIN rail W:Alarms and Redundant operation Specification is changed at option,refer to Instruction Manual. Please refer to derating curve, because the rated load current depends on cooling method that is convention cooling or forced air. SPECIFICATIONS MODEL VOLTAGE[V] FREQUENCY[Hz] ACIN 100V ACIN 200V ACIN 100V INPUT POWER FACTOR ACIN 200V ACIN 100V *1 INRUSH CURRENT[A] ACIN 200V *1 LEAKAGE CURRENT[mA] VOLTAGE[V] ACIN 100V *2 ACIN 100V *2 CURRENT[A] ACIN 200V *2 ACIN 200V *2 LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +50C *3 RIPPLE[mVp-p] OUTPUT -10 - 0C *3 0 to +50C *3 RIPPLE NOISE[mVp-p] -10 - 0C *3 TEMPERATURE REGULATION[mV] 0 to +50C *4 DRIFT[mV] START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION PROTECTION OVERVOLTAGE PROTECTION[V] CIRCUIT AND OPERATING INDICATION OTHERS ALARM OUTPUT REMOTE ON/OFF(RC) EFFICIENCY[%] *5 INPUT-OUTPUT -RC ISOLATION INPUT-FG *5 OUTPUT-RC-FG OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE ENVIRONMENT VIBRATION IMPACT AGENCY APPROVALS SAFETY AND CONDUCTED NOISE NOISE REGULATIONS CE MARKING HARMONIC ATTENUATOR CASE SIZE/WEIGHT OTHERS COOLING METHOD ADA600F-24 ADA600F-30 ADA600F-36 ADA600F-48 AC85 - 264 1f or DC 120 - 350 (AC64 or DC90 optionally available *6) 50/60 (47 - 63) or DC 84typ (Io=100%) 86typ (Io=100%) 86typ (Io=100%) 86typ (Io=100%) 86typ (Io=100%) 87typ (Io=100%) 87typ (Io=100%) 89typ (Io=100%) 0.99typ (Io=100%) 0.98typ (Io=100%) 20typ (Io=100%) (More than 3sec.to re-start) 40typ (Io=100%) (More than 3sec.to re-start) 0.75max (60Hz, According to IEC60950 and DEN-AN) (Io=100%) 24 30 36 48 14 (Peak 25) convection 11 (Peak 20) convection 9 (Peak 16.5) convection 6.5 (Peak 12.5) convection 21 (Peak 25) forced air 16.5 (Peak 20) forced air 14 (Peak 16.5) forced air 10.5 (Peak 12.5) forced air 15 (Peak 31) convection 12 (Peak 24.5) convection 10 (Peak 20.5) convection 7 (Peak 15.5) convection 25 (Peak 31) forced air 20 (Peak 24.5) forced air 16.5 (Peak 20.5) forced air 12.5 (Peak 15.5) forced air 96max 120max 144max 192max 150max 180max 240max 300max 120max 160max 200max 200max 160max 230max 260max 300max 150max 190max 230max 250max 180max 250max 280max 400max 240max 300max 360max 480max 96max 120max 144max 192max 500max (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 21.6 - 27.0 27.0 - 33.0 33.0 - 41.0 41.0 - 52.8 23.5 - 24.5 29.0 - 31.0 35.0 - 37.0 47.0 - 49.0 Works over 101% of peak current and recovers automatically 31 - 34.5 40 - 48 51 - 60 64 - 76 LED (Green) Detecting low input voltage(PF), detecting low output voltage(LV). (Optional : -W, refer to Instruction Manual 5) Requirement for external source (Option : -R, refer to Instruction Manual 5) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature) -10 to +71C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN and IEC60950-1 (At only AC input) Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B Low Voltage Directive, EMC Directive Complies with IEC61000-3-2 65X127X195mm (WXHXD) (without terminal block) /1.5kg max Convection/Forced air *1 The value is primary surge.The current of input surge to a built-in noise filter (0.2ms or less) is excluded. *2 Peak loading for 10sec.And Duty 35% max.Refer to Instruction Manual 4.Forced air is shown in Instruction Manual 2.3. *3 This is the value that measured on measuring board with capacitor of 22mF within 150mm from output terminal.Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to A-120 KEISOKU-GIKEN: RM101). *4 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *5 Applicable when remote control (optional) is added. *6 Derating is required.Consult us for details. * A sound may occur from power supply at pulse loading. ADA600F Block diagram Fuse 250V12A ADA Booster inductor Noise filter AC IN 85 - 264V Inrush current limitting Detecting current Rectifier Rectifier & Smooth FG Inverter Option Alarm circuit PF alarm (-W) Detecting current Control Option RC (-R) N+1 Redundancy Control External source (-W) Control Current Balance (CB) Master-Slave circuit Over voltage protection Voltage Balance (VB) Inverter Option Detecting output voltage LV alarm (-W) Rectifier & Smooth DC OUT External view 18.1 13 (22.6) 16.2 Voltage adjust CN3(Option) (19) LED 4-M4 Mounting hole (Bottom) 195 6.6 Name plate TB1 29 105 ±0.5 127 9 8 8.6 10 M3.5 FG hole 2-M4 Mounting hole 130.5 ±0.5 48 130.5 ±0.5 48 9 29±0.5 26.5 65 2-M4 Mounting hole Terminal cover 20 35 ±0.5 18 11 9 27.5 114.5 VB CB +V +V -V -V FG N L 8-M4 Mounting hole (Both sides) ¶ Pin assign Symbol VB CB +V +V -V -V FG N L CN3(Option) Function Voltage balance Current balance Output terminal(+) Output terminal(+) Output terminal(-) Output terminal(-) Frame ground AC(N) AC(L) Screw type Pin No. M3 2 1 4 3 6 5 8 7 10 9 12 11 14 13 M4 Average 21A max per pin for TB1 1 RC+ Function : Remote ON/OFF+(-R) 2 RC- : Remote ON/OFF-(-R) 3-8 NC : N.C. 9 LV+ : LV Alarm(-W) 10 LV- : LV Alarm ground(-W) 11-12 NC : N.C. 13 PF+ : PF Alarm(-W) 14 PF- : PF Alarm ground(-W) Connector Mating connector Terminal Chain:SPHD-002T-P0.5 PHDR-14VS Loose:BPHD-001T-P0.5 BPHD-002T-P0.5 *1 *1 Ratchet Hand is nothing CN3 S14B-PHDSS Mfr. J.S.T ¶ Tolerance : ±1 ¶ Weight : 1.5kg max ¶ PCB material / thickness : FR-4 / 1.6mm ¶ Chassis and cover material : aluminium ¶ Dimensions in mm ¶ Mounting torque : 1.2N • m(12.8kgf • cm) max ¶ Screw tighting torque M4 : 1.6N • m(16.9kgf • cm) max , M3 : 0.8N • m(8.5kgf • cm) max ¶ I/0 terminal for option-J and -T is shown in Instruction Manual 5. Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ ■ Änderungen vorbehalten / subject to change without notice ■ ■ ■ A-121