AP1694AS-13 OFFLINE, HIGH PF, HIGH EFFICIENCY DIMMABLE LED DRIVER CONTROLLER Description Pin Assignments NEW PRODUCT The AP1694AS-13 is a high performance AC-DC power factor corrector for mains dimmable LED driver applications. The device uses Pulse Frequency Modulation (PFM) technology to regulate output current while achieving high power factor and low THD. It operates as a BCM (Boundary Conduction Mode) controller which is good for EMI. (Top View) The AP1694AS-13 provides accurate constant current (CC) regulation while removing the opto-coupler and secondary control circuitry. It also eliminates the need for loop compensation circuitry while maintaining stability. It can meet the requirement of IEC6100-3-2 harmonic standard. The AP1694AS-13 features low start-up current and low operation current. It adopts valley on switching mode to achieve high efficiency. It also has rich protection features including overvoltage, short circuit, and over-temperature protection. The AP1694AS-13 provides the dimmable LED driver with a wide dimmer compatibility including leading edge and trailing edge dimmer. The AP1694AS-13 can achieve deep dimming down to 1%, while the dimming curve is compliant with the standard of NEMA SSL6. The AP1694AS-13 is available in SO-8 package. Applications Mains Dimmable LED Lighting 1 8 VCC RI 2 7 OUT SGND 3 6 GND CS 4 5 FB SO-8 Features Notes: NC Primary Side Control for Output Current Regulation without Optocoupler Boundary Conduction Mode (BCM) Operation to Achieve Highefficiency High PF and Low THD (PF > 0.9, THD < 30%) High Efficiency without Dimmer Wide Range of Dimmer Compatibility Dimming Curve Compliant with NEMA SSL6 Low Start-Up Current Tight LED Current Tight LED Open Voltage Valley-Mode Switching to Minimize the Transition Loss Mosfet Driver up to 25W Easy EMI Internal Protections: Under Voltage Lock Out(UVLO) Leading-Edge Blanking (LEB) Output Short Protection Output Open Protection Over Temperature Protection Flexible for Design with Small Form Factor and Very Low BOM Cost Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. “Green” Device (Note 3) 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds. AP1694AS-13 Document number: DS37789 Rev. 1 - 2 1 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Typical Applications Circuit L1 L RF BD1 R9 R3 R2 C1 F1 C4 OUT Q2 C2 TVS1 NEW PRODUCT N + D2 T1 D1 Z1 R4 C3 R5 VCC R1 FB Q1 RI OUT SGND GND R6 CS R7 R8 U1 AP1694AS-13 Typical Buck Application L1 L RF BD1 R9 R3 R2 C1 N F1 TVS1 Q2 C4 C2 D1 + OUT R4 T1 Z1 R5 C3 D2 R6 VCC FB R1 RI SGND GND Q1 OUT CS R7 R8 U1 AP1694AS-13 Typical Buck-Boost Application AP1694AS-13 Document number: DS37789 Rev. 1 - 2 2 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Typical Applications Circuit (continued) L1 L RF R9 F1 R2 + D3 Q2 C2 NEW PRODUCT TVS1 C5 R3 C1 N D2 R10 BD1 D1 C4 OUT R4 Z1 T1 R5 C3 R6 VCC FB R1 RI Q1 OUT SGND CS GND R7 R8 U1 AP1694AS-13 Typical Fly-Back Application Pin Descriptions Pin Number Pin Name 1 NC No connection. 2 RI The initial on time setting resistor. 3 SGND 4 CS Primary current sensing. 5 FB The feedback voltage from auxiliary winding. 6 GND Ground. 7 OUT Gate driver output. 8 VCC Supply voltage of gate driver and control circuits of the IC. AP1694AS-13 Document number: DS37789 Rev. 1 - 2 Function Must connect to GND. 3 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Functional Block Diagram VCC 8 Vdd CS_OCP Power_EN Vref 5 NEW PRODUCT FB Tons Detector 2 RI Regulator& Bias FB_CV PRO Protection & Latch FB_OVP VCC_OVP Tons Set Initial Tonp CC_CTRL S PFM Logic Q TONP_CTRL 7 Driver OUT R 3 SGND Vcs_valley 4 CS Vcsmax Constant Turn-on Time Generation 6 GND Absolute Maximum Ratings (Note 4) (@TA = +25°C, unless otherwise specified.) Symbol Rating Unit VCC Power Supply Voltage -0.3 to 35 V IOUT Driver Output Current 150 mA VCS Voltage at CS to GND -0.3 to 7 V VFB FB Input Voltage -40 to 10 V Operating Junction Temperature -40 to +150 °C TSTG Storage Temperature -65 to +150 °C TLEAD Lead Temperature (Soldering, 10 sec) +300 °C PD Power Dissipation (TA = +50C) 0.65 W θJA Thermal Resistance (Junction to Ambient) 160 °C/W ±2,000 V ±200 V TJ Note 4: Parameter – ESD (Human Body Model) – ESD (Machine Model) Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute Maximum Ratings” for extended periods may affect device reliability. AP1694AS-13 Document number: DS37789 Rev. 1 - 2 4 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Recommended Operating Conditions Symbol Parameter Max Unit VCC Power Supply Voltage 7 25 V TA Ambient Temperature -40 +105 °C Electrical Characteristics (@TA = +25°C, unless otherwise specified.) Symbol NEW PRODUCT Min Parameter Conditions Min Typ Max Unit UVLO Section Start-up Threshold – 13 14.5 16 V Minimum Operating Voltage After turn on 5.5 6.5 7.5 V VCC OVP Voltage – 27 29 31 V VCC Delatch Voltage (Note 5) – 3 4 5 V Start-up Current VCC = VTH (ST) -0.5V, Before start up – – 20 µA Operating Current Static – 900 1,300 µA Gate Voltage – 11 12 14 V ISOURCE_L Low Driver Source Current – 35 40 45 mA ISOURCE_H High Driver Source Current – 90 100 120 mA Sink Resistance – 6 7 8 Ω Current Sense Reference – – 1 – V Current Sense Reference Clamp – 1.2 1.4 – V Minimum tONP – 700 – 1,000 ns Delay to Output (Note 5) – 50 150 250 ns Feedback Pin Input Leakage Current VFB = 2V – – 4 µA VFB_CV FB CV Threshold – 3.8 4 4.2 V VFB_OVP FB OVP Threshold – 4.5 6 7.5 V System Output Current On Final Test Board – – – ±2 % VTH (ST) VOPR (Min) VCC_OVP – Standby Current Section IST ICC (OPR) Drive Output Section VGATE RDS(on) Current Sense Section VCS_REF VCS_CLAMP tONP_MIN tD(H-L) Feedback Input Section IFB Output Current – Over Temperature Protection Section Note 5: – Shutdown Temperature (Note 5) – +150 – – °C – Temperature Hysteresis (Note 5) – – +20 – °C These parameters, although guaranteed by design, are not 100% tested in production. AP1694AS-13 Document number: DS37789 Rev. 1 - 2 5 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Performance Characteristics CV Threshold vs. Supply Voltage Start-up Voltage vs. Ambient Temperature 4.2 16.0 15.5 4.1 Start-up Voltage (V) CV Threshold (V) 3.9 3.8 14.5 14.0 13.5 13.0 3.7 12.5 3.6 6 8 10 12 14 16 18 20 22 24 26 12.0 -40 28 -20 0 Supply Voltage (V) 20 40 60 80 100 120 o Ambient Temperature ( C) Minimal Operating Voltage vs. Ambient Temperature Start-up Current vs. Ambient Temperature 7.2 2.0 7.1 7.0 6.9 Start-up Current (A) Minimal Operating Voltage (V) 1.8 6.8 6.7 6.6 6.5 1.6 1.4 1.2 1.0 6.4 0.8 6.3 6.2 -40 -20 0 20 40 60 80 100 0.6 -40 120 -20 0 o 20 40 60 80 100 120 o Ambient Temperature ( C) Ambient Temperature ( C) Operating Current vs. Ambient Temperature CV Threshold vs. Ambient Temperature 1000 4.50 4.25 CV Threshold (V) 900 Operating Current (A) NEW PRODUCT 15.0 4.0 800 700 4.00 3.75 3.50 600 3.25 500 -40 -20 0 20 40 60 80 100 120 3.00 -40 o AP1694AS-13 Document number: DS37789 Rev. 1 - 2 -20 0 20 40 60 80 100 120 o Ambient Temperature ( C) Ambient Temperature ( C) 6 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Performance Characteristics (continued) FB Leakage Current vs. Ambient Temperature Supply Current vs. Supply Voltage 2.25 1200 1000 Supply Current (A) FB Leakage Current (A) NEW PRODUCT 2.00 1.75 1.50 1.25 1.00 -40 800 600 400 200 -20 0 20 40 60 80 100 0 0 120 Ambient Temperature ( C) AP1694AS-13 Document number: DS37789 Rev. 1 - 2 4 8 12 16 20 24 28 Supply Voltage (V) o 7 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Application Information Based on Buck Structure The AP1694AS-13 uses constant on time control method within one AC cycle to achieve the high power factor. When the dimmer is connected to the driver, although a part of input voltage is cut off by the dimmer, the system still operates in constant on time mode. In this way, good dimmer compatibility can be realized. L1 RF L BD1 NEW PRODUCT R9 R3 R2 C1 F1 N TVS1 + D2 C4 OUT Q2 C2 T1 D1 Z1 R4 C3 R5 VCC R1 FB Q1 RI OUT SGND GND R6 CS R7 R8 U1 AP1694AS-13 Figure 1. Typical Buck Application Circuit When the dimmer is connected, and the conduction angle of the dimmer is can be determined as: ; according to the control principle of the IC, the output current 1 Vcs _ ref sin( ) if（ ） 1 I o ( , ) I pk ( , ) 2 R8 2 0 else In consideration of the dead zone of the buck structure, the output current DC value can be calculated as below: I o _ mean k 1 0 I o ( , )d Where, Vcs _ ref is the reference of the current sense, and the typical value is 1V. is the cutoff angle of dimmer. is the phase of the input voltage. k is the current modification coefficient , and the value is approximate to be 0.7. When no dimmer is connected with the driver ( 0 ), the output current DC value can be calculated by: 1 V I o _ mean k cs_ref R8 AP1694AS-13 Document number: DS37789 Rev. 1 - 2 8 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Application Information Based on Buck Structure (continued) Design Parameters Setting the Current Sense Resistor R8 According to the equation of the output current, the current sense resistor R8 is determined: NEW PRODUCT R8 k Vcs _ ref I o _ mean Transformer Selection The typical non-isolated buck circuit in Figure 1 is usually selected, and the system is operating at boundary conduction mode. The switching frequency at the crest is set as fmin, the inductance can be calculated as below: L ( 2 Vin _ rms Vo ) R8 Vo Vcs _ ref 2 Vin _ rms f min Where, Vo is the output voltage. Vin _ rms is the RMS value of the input voltage. According to Ferrari's law of electromagnetic induction, the winding turns number of the buck inductance N L is: L i pk NL Ae Bm L Vcs _ ref Ae Bm R8 Where, Ae is the core effective area. Bm is the maximum magnetic flux density. The auxiliary winding is the power supply for VCC, the winding turns number Naux is: N aux N L Vcc Vo Vd Where, VCC is the power supply voltage for IC from auxiliary winding. Vd is the voltage drop of the freewheel diode. Setting the Initial On Time As the AP1694AS-13 adopts the constant on time control method, the AP1694AS-13 will generate an initial on time to start a working cycle. If the initial on time is longer than the rated on time, overshoot will happen. The initial on time is determined by resister R1 shown in Figure 1. According to the initial on time generation mechanism, the ton_initial is: t on _ initial 80 R1 10 12 s To guarantee the system with no overshoot phenomenon, the resistor R1 is selected: R1 1.25 L 1010 R8 2U in _ rms _ max AP1694AS-13 Document number: DS37789 Rev. 1 - 2 9 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Application Information Based on Buck Structure (cont.) In dimmable application, on the condition of the acceptable line regulation, the smaller R1 is selected, as it will be better for dimming performance. Valley On Control Method The valley on function can provide low turn-on switching losses for buck converter. The voltage across the power-switch is reflected by the auxiliary winding of the buck transformer. The voltage is sensed by FB pin. NEW PRODUCT FB 0.1V Valley 1µs Figure 2.Valley On-Control According to Figure 2, when the falling edge of 0.1V is sensed by FB pin, the AP1694AS-13 will see the toff time is over and delay 1µs to start a new operating cycle. By this way we can realize valley on function. Passive Damping and Bleeder Design The passive bleeder is designed to supply latching and holding current to eliminate misfire and flicker. L RF Passive Bleeding L1 Damping DB1 R9 C1 N F1 C2 Figure 3. LED Driver Schematic with Passive Bleeder A passive bleeder is composed of a resister (R9) and a capacitor (C2). C1 is input filter capacitor and RF is damper resistor. The passive bleeder includes a capacitor (C2, hundreds of nF) to provide latching current. To remove the voltage and current spike, a resistor (R9) is necessary to dampen the spike. In dimmable application, because a large C2 will affect the PF, THD and efficiency, the value of the capacitor (C2) selected should be suitable. Generally, 100nF/400V to 330nF/400V is recommended. RF is the damper for reducing the spike current caused by quick charging of C2 at firing. RF is selected from 20Ω to 100Ω for low-line application, and 51Ω to 200Ω for high-line application. If R9 is too small, R9 can’t fully dampen the spike current and ringing current will occur. The ringing current will cause the TRIAC misfire which will cause LED flicking. Another consideration in R9 selection is power loss; an R9 that is too large will make more power dissipation. Generally, a 200Ω to 2KΩ resistor is selected for R9. AP1694AS-13 Document number: DS37789 Rev. 1 - 2 10 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Application Information Based on Buck Structure (cont.) Fault Protection Over Voltage Protection and Output Open Protection VCC NEW PRODUCT RFB1 FB RFB2 AP1694A Figure 4. OVP Circuit The output voltage is sensed by the auxiliary winding voltage of the Buck transformer. The VCC pin and FB pin provide over voltage protection function. When the output is open or large transient happens, the output voltage will exceed the rated value. When the voltage of Vcc cap exceeds VCC_OVP or VFB_CV, the over voltage is triggered and the IC will discharge VCC. When the VCC is below the UVLO threshold voltage, IC will start a new work cycle and the Vcc cap is charged again by start resistance. If the over voltage condition still exists, the system will work in hiccup mode. Attention: If the external fast startup circuit is adding in the application and the over voltage protection and output open protection happen, the IC will trigger latch. Output Short Protection When the output is shorted, the output voltage will be clamped at zero. At this condition, VCC will drop down without auxiliary winding for power supply, and the VCC will drop to UVLO threshold voltage. The IC will shut down and restart a new operating cycle, and the V CC is charged by startup resistance. When VCC is higher than Vcc_start voltage, IC will output a bunch of pulses to control power switch on and off. When still no FB signal detected, the device will not output more pulses. The VCC will again drop to VCC UVLO threshold. If output short condition still exists, the system will operate in hiccup mode. Attention: If the external fast startup circuit is adding in the application, the device will not work at UVLO mode, and the device will work at minimum toff mode. Over Temperature Protection AP1694AS-13 has two kinds of over-temperature protection processes. First, if the system is operating normally, the ambient temperature is changed to +170°C, and suddenly the IC will trigger over-temperature protection which leads to a latch work mode. Second, if the system starts when the ambient temperature is higher than +150°C, over temperature protection will be triggered. So, the AP1694AS-13 can startup successfully when the ambient temperature is less than +150°C. Components Selection Guide If the system’s spec is changed, please refer to the design sheet of the AP1694AS-13 and select the compatible system parameter. When the system needs to be adjusted slightly, please refer to the table below and adjust the value of the related component. Item Description Related Components IO Output current R8 Output Current Ripple Small current ripple is good for LED life C4 ton_initial System initial on time, used to startup the system R1 Output Open Voltage Setting the output voltage when the LED is open R5, R6 Dimming Performance Improve the dimming performance EMI Pass EN 55022 class B with 6DB margin Line Compensation To get a good line regulation AP1694AS-13 Document number: DS37789 Rev. 1 - 2 11 of 14 www.diodes.com R1, RF, R9, C2, C4 L1, C1 R7 July 2015 © Diodes Incorporated AP1694AS-13 Ordering Information NEW PRODUCT AP1694A X - 13 Package Packing S: SO-8 13 : 13" Tape & Reel 13” Tape and Reel Part Number Package Code AP1694AS-13 Packaging S SO-8 Quantity Part Number Suffix 4,000/Tape & Reel -13 Marking Information (Top View) 8 7 6 5 Logo Part Number YY : Year : 15,16,17 ~ WW : Week : 01~52; 52 represents 52 and 53 week X X : Internal Code 1694AS-13 YY WW X X 1 AP1694AS-13 Document number: DS37789 Rev. 1 - 2 2 3 4 12 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 Package Outline Dimensions (All dimensions in mm (inch).) 0.254 Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for the latest version. E1 E A1 NEW PRODUCT L SO-8 Dim Min Max A 1.75 A1 0.10 0.20 A2 1.30 1.50 A3 0.15 0.25 b 0.3 0.5 D 4.85 4.95 E 5.90 6.10 E1 3.85 3.95 e 1.27 Typ h 0.35 L 0.62 0.82 0 8 All Dimensions in mm Gauge Plane Seating Plane Detail ‘A’ 7°~9° h 45° Detail ‘A’ A2 A A3 b e D Suggested Pad Layout Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version X Dimensions X Y C1 C2 C1 Value (in mm) 0.60 1.55 5.4 1.27 C2 Y AP1694AS-13 Document number: DS37789 Rev. 1 - 2 13 of 14 www.diodes.com July 2015 © Diodes Incorporated AP1694AS-13 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). NEW PRODUCT Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2015, Diodes Incorporated www.diodes.com AP1694AS-13 Document number: DS37789 Rev. 1 - 2 14 of 14 www.diodes.com July 2015 © Diodes Incorporated