PRELIMINARY Am29LV116B 16 Megabit (2 M x 8-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory DISTINCTIVE CHARACTERISTICS ■ Single power supply operation — Full voltage range: 2.7 to 3.6 volt read and write operations for battery-powered applications ■ Top or bottom boot block configurations available ■ Embedded Algorithms — Regulated voltage range: 3.0 to 3.6 volt read and write operations and for compatibility with high performance 3.3 volt microprocessors — Embedded Erase algorithm automatically preprograms and erases the entire chip or any combination of designated sectors ■ Manufactured on 0.35 µm process technology — Embedded Program algorithm automatically writes and verifies data at specified addresses ■ High performance — Full voltage range: access times as fast as 90 ns — Regulated voltage range: access times as fast as 80 ns ■ Ultra low power consumption (typical values at 5 MHz) — 200 nA Automatic Sleep mode current — 200 nA standby mode current — 9 mA read current — 15 mA program/erase current ■ Flexible sector architecture — One 16 Kbyte, two 8 Kbyte, one 32 Kbyte, and thirty-one 64 Kbyte sectors — Supports full chip erase — Sector Protection features: A hardware method of locking a sector to prevent any program or erase operations within that sector Sectors can be locked in-system or via programming equipment Temporary Sector Unprotect feature allows code changes in previously locked sectors ■ Unlock Bypass Program Command — Reduces overall programming time when issuing multiple program command sequences ■ Minimum 1,000,000 write cycle guarantee per sector ■ Package option — 40-pin TSOP ■ CFI (Common Flash Interface) compliant — Provides device-specific information to the system, allowing host software to easily reconfigure for different Flash devices ■ Compatibility with JEDEC standards — Pinout and software compatible with singlepower supply Flash — Superior inadvertent write protection ■ Data# Polling and toggle bits — Provides a software method of detecting program or erase operation completion ■ Ready/Busy# pin (RY/BY#) — Provides a hardware method of detecting program or erase cycle completion ■ Erase Suspend/Erase Resume — Suspends an erase operation to read data from, or program data to, a sector that is not being erased, then resumes the erase operation ■ Hardware reset pin (RESET#) — Hardware method to reset the device to reading array data This document contains information on a product under development at Advanced Micro Devices. The information is intended to help you evaluate this product. AMD reserves the right to change or discontinue work on this proposed product without notice. Publication# 21359 Rev: C Amendment/+2 Issue Date: March 1998 PRELIMINARY GENERAL DESCRIPTION The Am29LV116B is a 16 Mbit, 3.0 Volt-only Flash memory organized as 2,097,152 bytes. The device is offered in a 40-pin TSOP package. The byte-wide (x8) data appears on DQ7–DQ0. All read, program, and erase operations are accomplished using only a single power supply. The device can also be programmed in standard EPROM programmers. The standard device offers access times of 80, 90, and 120 ns, allowing high speed microprocessors to operate without wait states. To eliminate bus contention the device has separate chip enable (CE#), write enable (WE#) and output enable (OE#) controls. The device requires only a single 3.0 volt power supply for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. The device is entirely command set compatible with the JEDEC single-power-supply Flash standard. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state-machine that controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from other Flash or EPROM devices. Device programming occurs by executing the program command sequence. This initiates the Embedded Program algorithm—an internal algorithm that automatically times the program pulse widths and verifies proper cell margin. The Unlock Bypass mode facilitates faster programming times by requiring only two write cycles to program data instead of four. Device erasure occurs by executing the erase command sequence. This initiates the Embedded Erase algorithm—an internal algorithm that automatically preprograms the array (if it is not already programmed) before executing the erase operation. During erase, the device automatically times the erase pulse widths and verifies proper cell margin. The host system can detect whether a program or erase operation is complete by observing the RY/BY# pin, or by reading the DQ7 (Data# Polling) and DQ6 (toggle) status bits. After a program or erase cycle has been completed, the device is ready to read array data or accept another command. The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is fully erased when shipped from the factory. Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions. The hardware sector protection feature disables both program and erase operations in any combination of the sectors of memory. This can be achieved in-system or via programming equipment. The Erase Suspend feature enables the user to put erase on hold for any period of time to read data from, or program data to, any sector that is not selected for erasure. True background erase can thus be achieved. The hardware RESET# pin terminates any operation in progress and resets the internal state machine to reading array data. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the device, enabling the system microprocessor to read the boot-up firmware from the Flash memory. The device offers two power-saving features. When addresses have been stable for a specified amount of time, the device enters the automatic sleep mode. The system can also place the device into the standby mode. Power consumption is greatly reduced in both these modes. AMD’s Flash technology combines years of Flash memory manufacturing experience to produce the highest levels of quality, reliability and cost effectiveness. The device electrically erases all bits within a sector simultaneously via Fowler-Nordheim tunneling. The data is programmed using hot electron injection. Am29LV116B 2 PRELIMINARY PRODUCT SELECTOR GUIDE Family Part Number Speed Options Am29LV116B Regulated Voltage Range: VCC =3.0–3.6 V 80R Full Voltage Range: VCC = 2.7–3.6 V 90 120 Max access time, ns (tACC) 80 90 120 Max CE# access time, ns (tCE) 80 90 120 Max OE# access time, ns (tOE) 30 35 50 Note: See “AC Characteristics” for full specifications. BLOCK DIAGRAM DQ0–DQ7 RY/BY# VCC Sector Switches VSS Erase Voltage Generator RESET# WE# Input/Output Buffers State Control Command Register PGM Voltage Generator Chip Enable Output Enable Logic CE# OE# VCC Detector Address Latch STB Timer A0–A20 STB Data Latch Y-Decoder Y-Gating X-Decoder Cell Matrix 21359C-1 3 Am29LV116B PRELIMINARY CONNECTION DIAGRAMS A16 A15 A14 A13 A12 A11 A9 A8 WE# RESET# NC RY/BY# A18 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 A17 VSS A20 A19 A10 DQ7 DQ6 DQ5 DQ4 VCC VCC NC DQ3 DQ2 DQ1 DQ0 OE# VSS CE# A0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40-Pin Standard TSOP 40-Pin Reverse TSOP 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 A17 VSS A20 A19 A10 DQ7 DQ6 DQ5 DQ4 VCC VCC NC DQ3 DQ2 DQ1 DQ0 OE# VSS CE# A0 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 A16 A15 A14 A13 A12 A11 A9 A8 WE# RESET# NC RY/BY# A18 A7 A6 A5 A4 A3 A2 A1 21359C-2 Am29LV116B 4 PRELIMINARY PIN CONFIGURATION A0–A20 LOGIC SYMBOL = 21 addresses 21 DQ0–DQ7 = 8 data inputs/outputs A0–A20 CE# = Chip enable OE# = Output enable WE# = Write enable CE# RESET# = Hardware reset pin, active low OE# RY/BY# = Ready/Busy output WE# VCC = 3.0 volt-only single power supply (see Product Selector Guide for speed options and voltage supply tolerances) RESET# VSS = Device ground NC = Pin not connected internally 5 8 DQ0–DQ7 RY/BY# 21359C-3 Am29LV116B PRELIMINARY ORDERING INFORMATION Standard Products AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of the elements below. Am29LV116B T 80R E C OPTIONAL PROCESSING Blank = Standard Processing B = Burn-in (Contact an AMD representative for more information) TEMPERATURE RANGE C = Commercial (0°C to +70°C) I = Industrial (–40°C to +85°C) E = Extended (–55°C to +125°C) PACKAGE TYPE E = 40-Pin Thin Small Outline Package (TSOP) Standard Pinout (TS 040) F = 40-Pin Thin Small Outline Package (TSOP) Reverse Pinout (TSR040) SPEED OPTION See Product Selector Guide and Valid Combinations BOOT CODE SECTOR ARCHITECTURE T = Top Sector B = Bottom Sector DEVICE NUMBER/DESCRIPTION Am29LV116B 16 Megabit (2 M x 8-Bit) CMOS Flash Memory 3.0 Volt-only Read, Program, and Erase Valid Combinations Valid Combinations Am29LV116BT80R, Am29LV116BB80R Am29LV116BT90, Am29LV116BB90 Am29LV116BT120, Am29LV116BB120 EC, FC Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combinations. EC, EI, EE, FC, FI, FE Am29LV116B 6 PRELIMINARY DEVICE BUS OPERATIONS This section describes the requirements and use of the device bus operations, which are initiated through the internal command register. The command register itself does not occupy any addressable memory location. The register is composed of latches that store the commands, along with the address and data information needed to execute the command. The contents of the Table 1. Operation Read Write register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. Table 1 lists the device bus operations, the inputs and control levels they require, and the resulting output. The following subsections describe each of these operations in further detail. Am29LV116B Device Bus Operations CE# OE# WE# RESET# Addresses DQ0–DQ7 L L H H AIN DOUT L H L H AIN DIN X High-Z VCC ± 0.3 V X X VCC ± 0.3 V Output Disable L H H H X High-Z Reset X X X L X High-Z Sector Protect (See Note) L H L VID Sector Addresses, A6 = L, A1 = H, A0 = L DIN, DOUT Sector Unprotect (See Note) L H L VID Sector Addresses A6 = H, A1 = H, A0 = L DIN, DOUT Temporary Sector Unprotect X X X VID AIN DIN Standby Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 12.0 ± 0.5 V, X = Don’t Care, AIN = Address In, DIN = Data In, DOUT = Data Out Note: The sector protect and sector unprotect functions may also be implemented via programming equipment. See the “Sector Protection/Unprotection” section. Requirements for Reading Array Data Writing Commands/Command Sequences To read array data from the outputs, the system must drive the CE# and OE# pins to VIL. CE# is the power control and selects the device. OE# is the output control and gates array data to the output pins. WE# should remain at VIH. To write a command or command sequence (which includes programming data to the device and erasing sectors of memory), the system must drive WE# and CE# to VIL, and OE# to VIH. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. See “Reading Array Data” for more information. Refer to the AC Read Operations table for timing specifications and to Figure 13 for the timing diagram. ICC1 in the DC Characteristics table represents the active current specification for reading array data. 7 The device features an Unlock Bypass mode to facilitate faster programming. Once the device enters the Unlock Bypass mode, only two write cycles are required to program a byte, instead of four. The “Byte Program Command Sequence” section has details on programming data to the device using both standard and Unlock Bypass command sequences. An erase operation can erase one sector, multiple sectors, or the entire device. Tables 2 and 3 indicate the address space that each sector occupies. A “sector address” consists of the address bits required to uniquely select a sector. The “Command Definitions” section has details on erasing a sector or the entire chip, or suspending/resuming the erase operation. After the system writes the autoselect command sequence, the device enters the autoselect mode. The system can then read autoselect codes from the internal register (which is separate from the memory array) on DQ7–DQ0. Standard read cycle timings apply in this Am29LV116B PRELIMINARY mode. Refer to the Autoselect Mode and Autoselect Command Sequence sections for more information. ICC2 in the DC Characteristics table represents the active current specification for the write mode. The “AC Characteristics” section contains timing specification tables and timing diagrams for write operations. signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. I CC5 in the DC Characteristics table r epresen ts th e au to matic sle ep mod e c urr ent specification. RESET#: Hardware Reset Pin Program and Erase Operation Status During an erase or program operation, the system may check the status of the operation by reading the status bits on DQ7–DQ0. Standard read cycle timings and ICC read specifications apply. Refer to “Write Operation Status” for more information, and to “AC Characteristics” for timing diagrams. Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# pins are both held at VCC ± 0.3 V. (Note that this is a more restricted voltage range than VIH.) If CE# and RESET# are held at VIH, but not within VCC ± 0.3 V, the device will be in the standby mode, but the standby current will be greater. The device requires standard access time (tCE) for read access when the device is in either of these standby modes, before it is ready to read data. The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity. Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS±0.3 V, the device draws CMOS standby current (ICC4). If RESET# is held at VIL but not within VSS±0.3 V, the standby current will be greater. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. ICC3 in the DC Characteristics table represents the standby current specification. If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a “0” (busy) until the internal reset operation is complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/BY# to determine whether the reset operation is complete. If RESET# is asserted when a program or erase operation is not executing (RY/BY# pin is “1”), the reset operation is completed within a time of tREADY (not during Embedded Algorithms). The system can read data tRH after the RESET# pin returns to VIH. Automatic Sleep Mode Refer to the AC Characteristics tables for RESET# parameters and to Figure 14 for the timing diagram. The device also enters the standby mode when the RESET# pin is driven low. Refer to the next section, “RESET#: Hardware Reset Pin”. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for t AC C + 3 0 ns. The autom atic sl eep m ode is independent of the CE#, WE#, and OE# control Output Disable Mode When the OE# input is at VIH, output from the device is disabled. The output pins are placed in the high impedance state. Am29LV116B 8 PRELIMINARY Table 2. 9 Am29LV116BT Top Boot Sector Address Table Sector A20 A19 A18 A17 A16 A15 A14 A13 Sector Size (Kbytes) Address Range (in hexadecimal) SA0 0 0 0 0 0 X X X 64 000000–00FFFF SA1 0 0 0 0 1 X X X 64 010000–01FFFF SA2 0 0 0 1 0 X X X 64 020000–02FFFF SA3 0 0 0 1 1 X X X 64 030000–03FFFF SA4 0 0 1 0 0 X X X 64 040000–04FFFF SA5 0 0 1 0 1 X X X 64 050000–05FFFF SA6 0 0 1 1 0 X X X 64 060000–06FFFF SA7 0 0 1 1 1 X X X 64 070000–07FFFF SA8 0 1 0 0 0 X X X 64 080000–08FFFF SA9 0 1 0 0 1 X X X 64 090000–09FFFF SA10 0 1 0 1 0 X X X 64 0A0000–0AFFFF SA11 0 1 0 1 1 X X X 64 0B0000–0BFFFF SA12 0 1 1 0 0 X X X 64 0C0000–0CFFFF SA13 0 1 1 0 1 X X X 64 0D0000–0DFFFF SA14 0 1 1 1 0 X X X 64 0E0000–0EFFFF SA15 0 1 1 1 1 X X X 64 0F0000–0FFFFF SA16 1 0 0 0 0 X X X 64 100000–10FFFF SA17 1 0 0 0 1 X X X 64 110000–11FFFF SA18 1 0 0 1 0 X X X 64 120000–12FFFF SA19 1 0 0 1 1 X X X 64 130000–13FFFF SA20 1 0 1 0 0 X X X 64 140000–14FFFF SA21 1 0 1 0 1 X X X 64 150000–15FFFF SA22 1 0 1 1 0 X X X 64 160000–16FFFF SA23 1 0 1 1 1 X X X 64 170000–17FFFF SA24 1 1 0 0 0 X X X 64 180000–18FFFF SA25 1 1 0 0 1 X X X 64 190000–19FFFF SA26 1 1 0 1 0 X X X 64 1A0000–1AFFFF SA27 1 1 0 1 1 X X X 64 1B0000–1BFFFF SA28 1 1 1 0 0 X X X 64 1C0000–1CFFFF SA29 1 1 1 0 1 X X X 64 1D0000–1DFFFF SA30 1 1 1 1 0 X X X 64 1E0000–1EFFFF SA31 1 1 1 1 1 0 X X 32 1F0000–1F7FFF SA32 1 1 1 1 1 1 0 0 8 1F8000–1F9FFF SA33 1 1 1 1 1 1 0 1 8 1FA000–1FBFFF SA34 1 1 1 1 1 1 1 X 16 1FC000–1FFFFF Am29LV116B PRELIMINARY Table 3. Am29LV116BB Bottom Boot Sector Address Table Sector A20 A19 A18 A17 A16 A15 A14 A13 Sector Size (Kbytes) Address Range (in hexadecimal) SA0 0 0 0 0 0 0 0 X 16 000000–003FFF SA1 0 0 0 0 0 0 1 0 8 004000–005FFF SA2 0 0 0 0 0 0 1 1 8 006000–007FFF SA3 0 0 0 0 0 1 X X 32 008000–00FFFF SA4 0 0 0 0 1 X X X 64 010000–01FFFF SA5 0 0 0 1 0 X X X 64 020000–02FFFF SA6 0 0 0 1 1 X X X 64 030000–03FFFF SA7 0 0 1 0 0 X X X 64 040000–04FFFF SA8 0 0 1 0 1 X X X 64 050000–05FFFF SA9 0 0 1 1 0 X X X 64 060000–06FFFF SA10 0 0 1 1 1 X X X 64 070000–07FFFF SA11 0 1 0 0 0 X X X 64 080000–08FFFF SA12 0 1 0 0 1 X X X 64 090000–09FFFF SA13 0 1 0 1 0 X X X 64 0A0000–0AFFFF SA14 0 1 0 1 1 X X X 64 0B0000–0BFFFF SA15 0 1 1 0 0 X X X 64 0C0000–0CFFFF SA16 0 1 1 0 1 X X X 64 0D0000–0DFFFF SA17 0 1 1 1 0 X X X 64 0E0000–0EFFFF SA18 0 1 1 1 1 X X X 64 0F0000–0FFFFF SA19 1 0 0 0 0 X X X 64 100000–10FFFF SA20 1 0 0 0 1 X X X 64 110000–11FFFF SA21 1 0 0 1 0 X X X 64 120000–12FFFF SA22 1 0 0 1 1 X X X 64 130000–13FFFF SA23 1 0 1 0 0 X X X 64 140000–14FFFF SA24 1 0 1 0 1 X X X 64 150000–15FFFF SA25 1 0 1 1 0 X X X 64 160000–16FFFF SA26 1 0 1 1 1 X X X 64 170000–17FFFF SA27 1 1 0 0 0 X X X 64 180000–18FFFF SA28 1 1 0 0 1 X X X 64 190000–19FFFF SA29 1 1 0 1 0 X X X 64 1A0000–1AFFFF SA30 1 1 0 1 1 X X X 64 1B0000–1BFFFF SA31 1 1 1 0 0 X X X 64 1C0000–1CFFFF SA32 1 1 1 0 1 X X X 64 1D0000–1DFFFF SA33 1 1 1 1 0 X X X 64 1E0000–1EFFFF SA34 1 1 1 1 1 X X X 64 1F0000–1FFFFF Am29LV116B 10 PRELIMINARY Autoselect Mode Table 4. In addition, when verifying sector protection, the sector address must appear on the appropriate highest order address bits (see Tables 2 and 3). Table 4 shows the remaining address bits that are don’t care. When all necessary bits have been set as required, the programming equipment may then read the corresponding identifier code on DQ7-DQ0. The autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes output on DQ7–DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm. However, the autoselect codes can also be accessed in-system through the command register. To access the autoselect codes in-system, the host system can issue the autoselect command via the command register, as shown in Table 9. This method does not require VID. See “Command Definitions” for details on using the autoselect mode. When using programming equipment, the autoselect mode requires VID (11.5 V to 12.5 V) on address pin A9. Address pins A6, A1, and A0 must be as shown in Table 4. Am29LV116B Autoselect Codes (High Voltage Method) CE# OE# WE# A20 to A13 Manufacturer ID: AMD L L H X X VID X L X L L 01h Device ID: Am29LV116B (Top Boot Block) L L H X X VID X L X L H C7h Device ID: Am29LV116B (Bottom Boot Block) L L H X X VID X L X L H 4Ch Description A12 to A10 A9 A8 to A7 A6 A5 to A2 A1 A0 DQ7 to DQ0 01h (protected) Sector Protection Verification L L H SA X VID X L X H L 00h (unprotected) L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care. Sector Protection/Unprotection The hardware sector protection feature disables both program and erase operations in any sector. The hardware sector unprotection feature re-enables both program and erase operations in previously protected sectors. Sector protection/unprotection can be implemented via two methods. The primary method requires VID on the RESET# pin only, and can be implemented either in-system or via programming equipment. Figure 1 shows the algorithms and Figure 21 shows the timing diagram. This method uses standard microprocessor bus cycle timing. For sector unprotect, all unprotected sectors must first be protected prior to the first sector unprotect write cycle. The alternate method intended only for programming equipment requires VID on address pin A9 and OE#. This method is compatible with programmer routines written for earlier 3.0 volt-only AMD flash devices. Pub- 11 lication number 21586 contains further details; contact an AMD representative to request a copy. The device is shipped with all sectors unprotected. AMD offers the option of programming and protecting sectors at its factory prior to shipping the device through AMD’s ExpressFlash™ Service. Contact an AMD representative for details. It is possible to determine whether a sector is protected or unprotected. See “Autoselect Mode” for details. Temporary Sector Unprotect This feature allows temporary unprotection of previously protected sectors to change data in-system. The Sector Unprotect mode is activated by setting the RESET# pin to VID. During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses. Once VID is removed from the RESET# pin, all the previously protected sectors are protected again. Figure 2 shows the algorithm, and Figure 20 shows the timing diagrams, for this feature. Am29LV116B PRELIMINARY START START Protect all sectors: The indicated portion of the sector protect algorithm must be performed for all unprotected sectors prior to issuing the first sector unprotect address PLSCNT = 1 RESET# = VID Wait 1 µs Temporary Sector Unprotect Mode No PLSCNT = 1 RESET# = VID Wait 1 µs No First Write Cycle = 60h? First Write Cycle = 60h? Yes Yes Set up sector address No All sectors protected? Sector Protect: Write 60h to sector address with A6 = 0, A1 = 1, A0 = 0 Yes Set up first sector address Sector Unprotect: Write 60h to sector address with A6 = 1, A1 = 1, A0 = 0 Wait 150 µs Increment PLSCNT Temporary Sector Unprotect Mode Verify Sector Protect: Write 40h to sector address with A6 = 0, A1 = 1, A0 = 0 Reset PLSCNT = 1 Wait 15 ms Read from sector address with A6 = 0, A1 = 1, A0 = 0 Verify Sector Unprotect: Write 40h to sector address with A6 = 1, A1 = 1, A0 = 0 Increment PLSCNT No No PLSCNT = 25? Yes Yes No Yes Device failed Read from sector address with A6 = 1, A1 = 1, A0 = 0 Data = 01h? PLSCNT = 1000? Protect another sector? No No Data = 00h? Yes Yes Remove VID from RESET# Device failed Last sector verified? Write reset command Sector Protect Algorithm Sector Protect complete Set up next sector address No Yes Sector Unprotect Algorithm Remove VID from RESET# Write reset command Sector Unprotect complete 21359C-4 Figure 1. In-System Sector Protect/Unprotect Algorithms Am29LV116B 12 PRELIMINARY against inadvertent writes (refer to Table 9 for command definitions). In addition, the following hardware data protection measures prevent accidental erasure or programming, which might otherwise be caused by spurious system level signals during VCC power-up and power-down transitions, or from system noise. START RESET# = VID (Note 1) Low VCC Write Inhibit When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional writes when VCC is greater than VLKO. Perform Erase or Program Operations RESET# = VIH Temporary Sector Unprotect Completed (Note 2) Write Pulse “Glitch” Protection Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle. 21359C-5 Notes: 1. All protected sectors unprotected. Logical Inhibit 2. All previously protected sectors are protected once again. Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a logical one. Figure 2. Power-Up Write Inhibit Temporary Sector Unprotect Operation Hardware Data Protection The command sequence requirement of unlock cycles for programming or erasing provides data protection 13 If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to reading array data on power-up. Am29LV116B PRELIMINARY COMMON FLASH MEMORY INTERFACE (CFI) The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h, any time the device is ready to read array Table 5. data. The system can read CFI information at the addresses given in Tables 5–8. To terminate reading CFI data, the system must write the reset command. The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode, and the system can read CFI data at the addresses given in Tables 5–8. The system must write the reset command to return the device to the autoselect mode. For further information, please refer to the CFI Specification and CFI Publication 100, available via the World Wide Web at http://www.amd.com/products/nvd/overview/cfi.html. Alternatively, contact an AMD representative for copies of these documents. CFI Query Identification String Addresses Data Description 10h 11h 12h 51h 52h 59h Query Unique ASCII string “QRY” 13h 14h 02h 00h Primary OEM Command Set 15h 16h 40h 00h Address for Primary Extended Table 17h 18h 00h 00h Alternate OEM Command Set (00h = none exists) 19h 1Ah 00h 00h Address for Alternate OEM Extended Table (00h = none exists) Table 6. System Interface String Addresses Data Description 1Bh 27h VCC Min. (write/erase) D7–D4: volt, D3–D0: 100 millivolt 1Ch 36h VCC Max. (write/erase) D7–D4: volt, D3–D0: 100 millivolt 1Dh 00h VPP Min. voltage (00h = no VPP pin present) 1Eh 00h VPP Max. voltage (00h = no VPP pin present) 1Fh 04h Typical timeout per single byte/word write 2N µs 20h 00h Typical timeout for Min. size buffer write 2N µs (00h = not supported) 21h 0Ah Typical timeout per individual block erase 2N ms 22h 00h Typical timeout for full chip erase 2N ms (00h = not supported) 23h 05h Max. timeout for byte/word write 2N times typical 24h 00h Max. timeout for buffer write 2N times typical 25h 04h Max. timeout per individual block erase 2N times typical 26h 00h Max. timeout for full chip erase 2N times typical (00h = not supported) Am29LV116B 14 PRELIMINARY Table 7. Addresses Data Description N 27h 15h Device Size = 2 byte 28h 29h 00h 00h Flash Device Interface description (refer to CFI publication 100) 2Ah 2Bh 00h 00h Max. number of byte in multi-byte write = 2N (00h = not supported) 2Ch 04h Number of Erase Block Regions within device 2Dh 2Eh 2Fh 30h 00h 00h 40h 00h Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100) 31h 32h 33h 34h 01h 00h 20h 00h Erase Block Region 2 Information 35h 36h 37h 38h 00h 00h 80h 00h Erase Block Region 3 Information 39h 3Ah 3Bh 3Ch 1Eh 00h 00h 01h Erase Block Region 4 Information Table 8. 15 Device Geometry Definition Primary Vendor-Specific Extended Query Addresses Data Description 40h 41h 42h 50h 52h 49h Query-unique ASCII string “PRI” 43h 31h Major version number, ASCII 44h 30h Minor version number, ASCII 45h 00h Address Sensitive Unlock 0 = Required, 1 = Not Required 46h 02h Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write 47h 01h Sector Protect 0 = Not Supported, X = Number of sectors in per group 48h 01h Sector Temporary Unprotect: 00 = Not Supported, 01 = Supported 49h 04h Sector Protect/Unprotect scheme 01 = 29F040 mode, 02 = 29F016 mode, 03 = 29F400 mode, 04 = 29LV800A mode 4Ah 00h Simultaneous Operation: 00 = Not Supported, 01 = Supported 4Bh 00h Burst Mode Type: 00 = Not Supported, 01 = Supported 4Ch 00h Page Mode Type: 00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page Am29LV116B PRELIMINARY COMMAND DEFINITIONS Writing specific address and data commands or sequences into the command register initiates device operations. Table 9 defines the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence resets the device to reading array data. All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on the rising edge of WE# or CE#, whichever happens first. Refer to the appropriate timing diagrams in the “AC Characteristics” section. Reading Array Data The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is also ready to read array data after completing an Embedded Program or Embedded Erase algorithm. After the device accepts an Erase Suspend command, the device enters the Erase Suspend mode. The system can read array data using the standard read timings, except that if it reads at an address within erasesuspended sectors, the device outputs status data. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See “Erase Suspend/Erase Resume Commands” for more information on this mode. The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode, the reset command must be written to return to reading array data (also applies to autoselect during Erase Suspend). If DQ5 goes high during a program or erase operation, writing the reset command returns the device to reading array data (also applies during Erase Suspend). Autoselect Command Sequence The autoselect command sequence allows the host system to access the manufacturer and devices codes, and determine whether or not a sector is protected. Table 9 shows the address and data requirements. This method is an alternative to that shown in Table 4, which is intended for PROM programmers and requires VID on address bit A9. The autoselect command sequence is initiated by writing two unlock cycles, followed by the autoselect command. The device then enters the autoselect mode, and the system may read at any address any number of times, without initiating another command sequence. A read cycle at address XX00h retrieves the manufacturer code. A read cycle at address XX01h returns the device code. A read cycle containing a sector address (SA) and the address 02h returns 01h if that sector is protected, or 00h if it is unprotected. Refer to Tables 2 and 3 for valid sector addresses. The system must issue the reset command to re-enable the device for reading array data if DQ5 goes high, or while in the autoselect mode. See the “Reset Command” section, next. The system must write the reset command to exit the autoselect mode and return to reading array data. See also “Requirements for Reading Array Data” in the “Device Bus Operations” section for more information. The Read Operations table provides the read parameters, and Figure 13 shows the timing diagram. The device programs one byte of data for each program operation. The command sequence requires four bus cycles, and is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically generates the program pulses and verifies the programmed cell margin. Table 9 shows the address and data requirements for the byte program command sequence. Reset Command Writing the reset command to the device resets the device to reading array data. Address bits are don’t care for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the device to reading array data. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the device to reading array data (also applies to programming in Erase Suspend mode). Once programming begins, however, the device ignores reset commands until the operation is complete. Byte Program Command Sequence When the Embedded Program algorithm is complete, the device then returns to reading array data and addresses are no longer latched. The system can determine the status of the program operation by using DQ7, DQ6, or RY/BY#. See “Write Operation Status” for information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardware reset immediately terminates the programming operation. The Byte Program command se- Am29LV116B 16 PRELIMINARY quence should be reinitiated once the device has reset to reading array data, to ensure data integrity. START Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from a “0” back to a “1”. Attempting to do so may halt the operation and set DQ5 to “1,” or cause the Data# Polling algorithm to indicate the operation was successful. However, a succeeding read will show that the data is still “0”. Only erase operations can convert a “0” to a “1”. Write Program Command Sequence Data Poll from System Unlock Bypass Command Sequence The unlock bypass feature allows the system to program bytes to the device faster than using the standard program command sequence. The unlock bypass command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. The device then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is required to program in this mode. The first cycle in this sequence contains the unlock bypass program command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. Table 9 shows the requirements for the command sequence. During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the data 90h; the second cycle the data 00h. Addresses are don’t cares for both cycles. The device then returns to reading array data. Embedded Program algorithm in progress Verify Data? Yes Increment Address No Last Address? Yes Programming Completed 21359C-6 Note: See Table 9 for program command sequence. Figure 3 illustrates the algorithm for the program operation. See the Erase/Program Operations table in “AC Characteristics” for parameters, and to Figure 15 for timing diagrams 17 No Am29LV116B Figure 3. Program Operation PRELIMINARY Chip Erase Command Sequence Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Table 9 shows the address and data requirements for the chip erase command sequence. ensure all commands are accepted. The interrupts can be re-enabled after the last Sector Erase command is written. If the time between additional sector erase commands can be assumed to be less than 50 µs, the system need not monitor DQ3. Any command other than Sector Erase or Erase Suspend during the time-out period resets the device to reading array data. The system must rewrite the command sequence and any additional sector addresses and commands. The system can monitor DQ3 to determine if the sector erase timer has timed out. (See the “DQ3: Sector Erase Timer” section.) The time-out begins from the rising edge of the final WE# pulse in the command sequence. Any commands written to the chip during the Embedded Erase algorithm are ignored. Note that a hardware reset during the chip erase operation immediately terminates the operation. The Chip Erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. Note that a hardware reset during the sector erase operation immediately terminates the operation. The Sector Erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/BY#. See “Write Operation Status” for information on these status bits. When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. When the Embedded Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, DQ2, or RY/BY#. (Refer to “Write Operation Status” for information on these status bits.) Figure 4 illustrates the algorithm for the erase operation. See the Erase/Program Operations tables in “AC Characteristics” for parameters, and to Figure 16 for timing diagrams. Figure 4 illustrates the algorithm for the erase operation. Refer to the Erase/Program Operations tables in the “AC Characteristics” section for parameters, and to Figure 16 for timing diagrams. Sector Erase Command Sequence Erase Suspend/Erase Resume Commands Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the address of the sector to be erased, and the sector erase command. Table 9 shows the address and data requirements for the sector erase command sequence. The Erase Suspend command allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. This command is valid only during the sector erase operation, including the time-out period 50 µs during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation or Embedded Program algorithm. Writing the Erase Suspend command during the Sector Erase time-out immediately terminates the time-out period and suspends the erase operation. Addresses are “don’t-cares” when writing the Erase Suspend command. The device does not require the system to preprogram the memory prior to erase. The Embedded Erase algorithm automatically programs and verifies the sector for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. After the command sequence is written, a sector erase time-out of 50 µs begins. During the time-out period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 µs, otherwise the last address and command might not be accepted, and erasure may begin. It is recommended that processor interrupts be disabled during this time to When the Erase Suspend command is written during a sector erase operation, the device requires a maximum of 20 µs to suspend the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. After the erase operation has been suspended, the system can read array data from or program data to any sector not selected for erasure. (The device “erase Am29LV116B 18 PRELIMINARY suspends” all sectors selected for erasure.) Normal read and write timings and command definitions apply. Reading at any address within erase-suspended sectors produces status data on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. See “Write Operation Status” for information on these status bits. START Write Erase Command Sequence After an erase-suspended program operation is complete, the system can once again read array data within non-suspended sectors. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. See “Write Operation Status” for more information. Data Poll from System The system may also write the autoselect command sequence when the device is in the Erase Suspend mode. The device allows reading autoselect codes even at addresses within erasing sectors, since the codes are not stored in the memory array. When the device exits the autoselect mode, the device reverts to the Erase Suspend mode, and is ready for another valid operation. See “Autoselect Command Sequence” for more information. The system must write the Erase Resume command (address bits are “don’t care”) to exit the erase suspend mode and continue the sector erase operation. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the device has resumed erasing. 19 No Embedded Erase algorithm in progress Data = FFh? Yes Erasure Completed 21359C-7 Notes: 1. See Table 9 for erase command sequence. 2. See “DQ3: Sector Erase Timer” for more information. Am29LV116B Figure 4. Erase Operation PRELIMINARY Table 9. Cycles Bus Cycles (Notes 2–4) Addr Data Read (Note 5) 1 RA RD Reset (Note 6) 1 XXX F0 4 555 4 555 Autoselect (Note 7) Command Sequence (Note 1) Manufacturer ID Device ID, Top Boot Block Device ID, Bottom Boot Block Am29LV116B Command Definitions First Second Third Fourth Addr Data Addr Data Addr Data AA 2AA 55 555 90 X00 01 AA 2AA 55 555 90 X01 Fifth Sixth Addr Data Addr Data C7 4C 4 555 AA 2AA 55 555 90 SA X02 00 Byte Program 4 555 AA 2AA 55 555 A0 PA PD Unlock Bypass 3 555 AA 2AA 55 555 20 Unlock Bypass Program (Note 9) 2 XXX A0 PA PD Unlock Bypass Reset (Note 10) 2 XXX 90 XXX 00 Chip Erase 6 555 AA 2AA 55 555 80 555 AA 2AA 55 555 10 2AA 55 555 80 555 AA 2AA 55 SA 30 Sector Protect Verify (Note 8) Sector Erase 6 555 AA Erase Suspend (Note 11) 1 XXX B0 Erase Resume (Note 12) 1 XXX 30 01 Legend: X = Don’t care PD = Data to be programmed at location PA. Data is latched on the rising edge of WE# or CE# pulse. RA = Address of the memory location to be read. RD = Data read from location RA during read operation. PA = Address of the memory location to be programmed. Addresses are latched on the falling edge of the WE# or CE# pulse. Notes: 1. See Table 1 for descriptions of bus operations. SA = Address of the sector to be erased or verified. Address bits A20–A13 uniquely select any sector. 2. All values are in hexadecimal. 8. The data is 00h for an unprotected sector and 01h for a protected sector. 3. Except when reading array or autoselect data, all bus cycles are write operations. 9. The Unlock Bypass command is required prior to the Unlock Bypass Program command. 4. Address bits A20–A11 are don’t care for unlock and command cycles, except when PA or SA is required. 10. The Unlock Bypass Reset command is required to return to reading array data when the device is in the Unlock Bypass mode. 5. No unlock or command cycles required when device is in read mode. 6. The Reset command is required to return to the read mode when the device is in the autoselect mode or if DQ5 goes high. 7. The fourth cycle of the autoselect command sequence is a read cycle. 11. The system may read and program functions in nonerasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 12. The Erase Resume command is valid only during the Erase Suspend mode. Am29LV116B 20 PRELIMINARY WRITE OPERATION STATUS The device provides several bits to determine the status of a write operation: DQ2, DQ3, DQ5, DQ6, DQ7, and RY/BY#. Table 10 and the following subsections describe the functions of these bits. DQ7, RY/BY#, and DQ6 each offer a method for determining whether a program or erase operation is complete or in progress. These three bits are discussed first. START Read DQ7–DQ0 Addr = VA DQ7: Data# Polling The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Algorithm is in progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the program or erase command sequence. During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then the device returns to reading array data. During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7. This is analogous to the complement/true datum output described for the Embedded Program algorithm: the erase function changes all the bits in a sector to “1”; prior to this, the device outputs the “complement,” or “0.” The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 µs, then the device returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. DQ7 = Data? No No DQ5 = 1? Yes Read DQ7–DQ0 Addr = VA DQ7 = Data? Yes No FAIL PASS Notes: 1. VA = Valid address for programming. During a sector erase operation, a valid address is an address within any sector selected for erasure. During chip erase, a valid address is any non-protected sector address. 2. DQ7 should be rechecked even if DQ5 = “1” because DQ7 may change simultaneously with DQ5. When the system detects DQ7 has changed from the complement to true data, it can read valid data at DQ7– DQ0 on the following read cycles. This is because DQ7 may change asynchronously with DQ0–DQ6 while Output Enable (OE#) is asserted low. Figure 17, Data# Polling Timings (During Embedded Algorithms), in the “AC Characteristics” section illustrates this. Table 10 shows the outputs for Data# Polling on DQ7. Figure 5 shows the Data# Polling algorithm. 21 Yes Am29LV116B 21359C-8 Figure 5. Data# Polling Algorithm PRELIMINARY RY/BY#: Ready/Busy# The RY/BY# is a dedicated, open-drain output pin that indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC. (The RY/BY# pin is not available on the 44-pin SO package.) If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is ready to read array data (including during the Erase Suspend mode), or is in the standby mode. Table 10 shows the outputs for RY/BY#. Figures 13, 15 and 16 shows RY/BY# for reset, program, and erase operations, respectively. DQ6: Toggle Bit I Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle (The system may use either OE# or CE# to control the read cycles). When the operation is complete, DQ6 stops toggling. After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100 µs, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erasesuspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see the subsection on DQ7: Data# Polling). If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the program command sequence is written, then returns to reading array data. DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program algorithm is complete. Table 10 shows the outputs for Toggle Bit I on DQ6. Figure 6 shows the toggle bit algorithm in flowchart form, and the section “Reading Toggle Bits DQ6/DQ2” explains the algorithm. Figure 18 in the “AC Characteristics” section shows the toggle bit timing diagrams. Figure 19 shows the differences between DQ2 and DQ6 in graphical form. See also the subsection on DQ2: Toggle Bit II. DQ2: Toggle Bit II The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 10 to compare outputs for DQ2 and DQ6. Figure 6 shows the toggle bit algorithm in flowchart form, and the section “Reading Toggle Bits DQ6/DQ2” explains the algorithm. See also the DQ6: Toggle Bit I subsection. Figure 18 shows the toggle bit timing diagram. Figure 19 shows the differences between DQ2 and DQ6 in graphical form. Reading Toggle Bits DQ6/DQ2 Refer to Figure 6 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erase operation. The system can read array data on DQ7–DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erase operation. If it is still toggling, the device did not completed the operation successfully, and the system Am29LV116B 22 PRELIMINARY must write the reset command to return to reading array data. START The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 6). Read DQ7–DQ0 (Note 1) Read DQ7–DQ0 Table 10 shows the outputs for Toggle Bit I on DQ6. Figure 6 shows the toggle bit algorithm. Figure 18 in the “AC Characteristics” section shows the toggle bit timing diagrams. Figure 19 shows the differences between DQ2 and DQ6 in graphical form. See also the subsection on DQ2: Toggle Bit II. Toggle Bit = Toggle? No Yes No DQ5 = 1? Yes Read DQ7–DQ0 Twice Toggle Bit = Toggle? (Notes 1, 2) No Yes Program/Erase Operation Not Complete, Write Reset Command Program/Erase Operation Complete Notes: 1. Read toggle bit twice to determine whether or not it is toggling. See text. 2. Recheck toggle bit because it may stop toggling as DQ5 changes to “1”. See text. 21359C-9 Figure 6. 23 Am29LV116B Toggle Bit Algorithm PRELIMINARY DQ5: Exceeded Timing Limits DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit. Under these conditions DQ5 produces a “1.” This is a failure condition that indicates the program or erase cycle was not successfully completed. The DQ5 failure condition may appear if the system tries to program a “1” to a location that is previously programmed to “0.” Only an erase operation can change a “0” back to a “1.” Under this condition, the device halts the operation, and when the operation has exceeded the timing limits, DQ5 produces a “1.” Under both these conditions, the system must issue the reset command to return the device to reading array data. DQ3: Sector Erase Timer After writing a sector erase command sequence, the system may read DQ3 to determine whether or not an erase operation has begun. (The sector erase timer does not apply to the chip erase command.) If addi- Table 10. Erase Suspend Mode After the sector erase command sequence is written, the system should read the status on DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure the device has accepted the command sequence, and then read DQ3. If DQ3 is “1”, the internally controlled erase cycle has begun; all further commands (other than Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0”, the device will accept additional sector erase commands. To ensure the command has been accepted, the system software should check the status of DQ3 prior to and following each subsequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 10 shows the outputs for DQ3. Write Operation Status DQ7 (Note 2) DQ6 DQ5 (Note 1) DQ3 DQ2 (Note 2) DQ7# Toggle 0 N/A No toggle 0 Embedded Erase Algorithm 0 Toggle 0 1 Toggle 0 Reading within Erase Suspended Sector 1 No toggle 0 N/A Toggle 1 Reading within Non-Erase Suspended Sector Data Data Data Data Data 1 Erase-Suspend-Program DQ7# Toggle 0 N/A N/A 0 Operation Standard Mode tional sectors are selected for erasure, the entire timeout also applies after each additional sector erase command. When the time-out is complete, DQ3 switches from “0” to “1.” If the time between additional sector erase commands from the system can be assumed to be less than 50 µs, the system need not monitor DQ3. See also the “Sector Erase Command Sequence” section. Embedded Program Algorithm RY/BY# Notes: 1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. See “DQ5: Exceeded Timing Limits” for more information. 2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. Am29LV116B 24 PRELIMINARY ABSOLUTE MAXIMUM RATINGS Storage Temperature Plastic Packages . . . . . . . . . . . . . . . –65°C to +150°C Ambient Temperature with Power Applied. . . . . . . . . . . . . . –65°C to +125°C Voltage with Respect to Ground VCC (Note 1) . . . . . . . . . . . . . . . . .–0.5 V to +4.0 V A9, OE#, and RESET# (Note 2) . . . . . . . . . . . .–0.5 V to +12.5 V 20 ns 20 ns +0.8 V –0.5 V –2.0 V 20 ns All other pins (Note 1) . . . . . . –0.5 V to VCC+0.5 V Output Short Circuit Current (Note 3) . . . . . . 200 mA Notes: 1. Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input or I/O pins may undershoot VSS to –2.0 V for periods of up to 20 ns. See Figure 7. Maximum DC voltage on input or I/O pins is VCC +0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 8. 2. Minimum DC input voltage on pins A9, OE#, and RESET# is –0.5 V. During voltage transitions, A9, OE#, and RESET# may undershoot VSS to –2.0 V for periods of up to 20 ns. See Figure 7. Maximum DC input voltage on pin A9 is +12.5 V which may overshoot to 14.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. 21359C-10 Figure 7. 20 ns VCC +2.0 V VCC +0.5 V 2.0 V 20 ns 20 ns 21359C-11 Figure 8. OPERATING RANGES Commercial (C) Devices Ambient Temperature (TA) . . . . . . . . . . . 0°C to +70°C Industrial (I) Devices Ambient Temperature (TA) . . . . . . . . . –40°C to +85°C Extended (E) Devices Ambient Temperature (TA) . . . . . . . . –55°C to +125°C VCC Supply Voltages VCC for regulated voltage range. . . . . .+3.0 V to 3.6 V VCC for full voltage range . . . . . . . . . . .+2.7 V to 3.6 V Operating ranges define those limits between which the functionality of the device is guaranteed. 25 Maximum Negative Overshoot Waveform Am29LV116B Maximum Positive Overshoot Waveform PRELIMINARY DC CHARACTERISTICS CMOS Compatible Parameter Description Test Conditions Min ILI Input Load Current VIN = VSS to VCC, VCC = VCC max ILIT A9 Input Load Current VCC = VCC max; A9 = 12.5 V ILO Output Leakage Current VOUT = VSS to VCC, VCC = VCC max ICC1 VCC Active Read Current (Note 1) VCC = VCC max; CE# = VIL, OE# = VIH ICC2 VCC Active Write Current (Notes 2 and 4) ICC3 Typ Max Unit ±1.0 µA 35 µA ±1.0 µA 5 MHz 9 16 1 MHz 2 4 VCC = VCC max; CE# = VIL, OE# = VIH 15 30 mA VCC Standby Current VCC = VCC max; CE#, RESET# = VCC±0.3 V 0.2 5 µA ICC4 VCC Reset Current VCC = VCC max; RESET# = VSS ± 0.3 V 0.2 5 µA ICC5 Automatic Sleep Mode (Note 3) VCC = VCC max; VIH = VCC ± 0.3 V; VIL = VSS ± 0.3 V 0.2 5 µA VIL Input Low Voltage –0.5 0.8 V VIH Input High Voltage 0.7 x VCC VCC + 0.3 V VID Voltage for Autoselect and Temporary Sector Unprotect VCC = 3.3 V 11.5 12.5 V VOL Output Low Voltage IOL = 4.0 mA, VCC = VCC min 0.45 V VOH1 Output High Voltage VOH2 VLKO mA IOH = –2.0 mA, VCC = VCC min 0.85 VCC IOH = –100 µA, VCC = VCC min VCC–0.4 Low VCC Lock-Out Voltage (Note 4) 2.3 V 2.5 V Notes: 1. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH. Typical specifications are for VCC = 3.0 V. 2. ICC active while Embedded Erase or Embedded Program is in progress. 3. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. 4. Not 100% tested. Am29LV116B 26 PRELIMINARY DC CHARACTERISTICS (Continued) Zero Power Flash Supply Current in mA 25 20 15 10 5 0 0 500 1000 1500 2000 2500 3000 3500 4000 Time in ns Note: Addresses are switching at 1 MHz 21359C-12 Figure 9. ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents) 10 3.6 V Supply Current in mA 8 2.7 V 6 4 2 0 1 2 3 4 5 Frequency in MHz Note: T = 25 °C 21359C-13 Figure 10. 27 Typical ICC1 vs. Frequency Am29LV116B PRELIMINARY TEST CONDITIONS Table 11. Test Specifications 3.3 V Test Condition Output Load 2.7 kΩ Device Under Test 80R 30 Input Rise and Fall Times 6.2 kΩ 100 pF 5 ns 0.0–3.0 V Input timing measurement reference levels 1.5 V Output timing measurement reference levels 1.5 V Input Pulse Levels Note: Diodes are IN3064 or equivalent Unit 1 TTL gate Output Load Capacitance, CL (including jig capacitance) CL 90, 120 21359C-14 Figure 11. Test Setup KEY TO SWITCHING WAVEFORMS WAVEFORM INPUTS OUTPUTS Steady Changing from H to L Changing from L to H Don’t Care, Any Change Permitted Changing, State Unknown Does Not Apply Center Line is High Impedance State (High Z) KS000010-PAL 3.0 V Input 1.5 V Measurement Level 1.5 V Output 0.0 V 21359C-15 Figure 12. Input Waveforms and Measurement Levels Am29LV116B 28 PRELIMINARY AC CHARACTERISTICS Read Operations Parameter Speed Option JEDEC Std Description tAVAV tRC Read Cycle Time (Note 1) tAVQV tACC Address to Output Delay tELQV tCE Chip Enable to Output Delay tGLQV tOE tEHQZ tGHQZ tAXQX Test Setup 80R 90 120 Unit Min 80 90 120 ns CE# = VIL OE# = VIL Max 80 90 120 ns OE# = VIL Max 80 90 120 ns Output Enable to Output Delay Max 30 35 50 ns tDF Chip Enable to Output High Z (Note 1) Max 25 30 30 ns tDF Output Enable to Output High Z (Note 1) Max 25 30 30 ns Read Min 0 ns Toggle and Data# Polling Min 10 ns Min 0 ns tOEH Output Enable Hold Time (Note 1) tOH Output Hold Time From Addresses, CE# or OE#, Whichever Occurs First (Note 1) Notes: 1. Not 100% tested. 2. See Figure 11 and Table 11 for test specifications. tRC Addresses Stable Addresses tACC CE# tDF tOE OE# tOEH WE# tCE tOH HIGH Z HIGH Z Output Valid Outputs RESET# RY/BY# 0V 21359C-16 Figure 13. 29 Read Operations Timings Am29LV116B PRELIMINARY AC CHARACTERISTICS Hardware Reset (RESET#) Parameter JEDEC Std Description Test Setup All Speed Options Unit tREADY RESET# Pin Low (During Embedded Algorithms) to Read or Write (See Note) Max 20 µs tREADY RESET# Pin Low (NOT During Embedded Algorithms) to Read or Write (See Note) Max 500 ns tRP RESET# Pulse Width Min 500 ns tRH RESET# High Time Before Read (See Note) Min 50 ns tRPD RESET# Low to Standby Mode Min 20 µs tRB RY/BY# Recovery Time Min 0 ns Note: Not 100% tested. RY/BY# CE#, OE# tRH RESET# tRP tReady Reset Timings NOT during Embedded Algorithms Reset Timings during Embedded Algorithms tReady RY/BY# tRB CE#, OE# RESET# tRP 21359C-17 Figure 14. RESET# Timings Am29LV116B 30 PRELIMINARY AC CHARACTERISTICS Erase/Program Operations Parameter JEDEC Std. Description tAVAV tWC Write Cycle Time (Note 1) Min tAVWL tAS Address Setup Time Min tWLAX tAH Address Hold Time Min 45 45 50 ns tDVWH tDS Data Setup Time Min 35 45 50 ns tWHDX tDH Data Hold Time Min 0 ns tOES Output Enable Setup Time (Note 1) Min 0 ns tGHWL tGHWL Read Recovery Time Before Write (OE# High to WE# Low) Min 0 ns tELWL tCS CE# Setup Time Min 0 ns tWHEH tCH CE# Hold Time Min 0 ns tWLWH tWP Write Pulse Width Min tWHWL tWPH Write Pulse Width High Min 30 ns tWHWH1 tWHWH1 Programming Operation (Note 2) Typ 9 µs tWHWH2 tWHWH2 Sector Erase Operation (Note 2) Typ 0.7 sec tVCS VCC Setup Time (Note 1) Min 50 µs tRB Recovery Time from RY/BY# Min 0 ns Program/Erase Valid to RY/BY# Delay Min 90 ns tBUSY Notes: 1. Not 100% tested. 2. See the “Erase and Programming Performance” section for more information. 31 Am29LV116B 80R 90 120 Unit 80 90 120 ns 0 35 35 ns 50 ns PRELIMINARY AC CHARACTERISTICS Read Status Data (last two cycles) Program Command Sequence (last two cycles) tAS tWC Addresses 555h PA PA PA tAH CE# tCH tGHWL OE# tWHWH1 tWP WE# tWPH tCS tDS tDH PD A0h Data Status DOUT tBUSY tRB RY/BY# tVCS VCC 21359C-18 Notes: 1. PA = program address, PD = program data, DOUT is the true data at the program address. Figure 15. Program Operation Timings Erase Command Sequence (last two cycles) tAS tWC 2AAh Addresses Read Status Data VA SA VA 555h for chip erase tAH CE# tGHWL tCH OE# tWP WE# tWPH tCS tWHWH2 tDS tDH Data 55h In Progress 30h Complete 10 for Chip Erase tBUSY tRB RY/BY# tVCS VCC 21359C-19 Notes: 1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”). Figure 16. Chip/Sector Erase Operation Timings Am29LV116B 32 PRELIMINARY AC CHARACTERISTICS tRC Addresses VA VA VA tACC tCE CE# tCH tOE OE# tOEH tDF WE# tOH High Z DQ7 Complement Complement DQ0–DQ6 Status Data Status Data Valid Data True High Z Valid Data True tBUSY RY/BY# Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle. 21359C-20 Figure 17. Data# Polling Timings (During Embedded Algorithms) tRC Addresses VA VA VA VA tACC tCE CE# tCH tOE OE# tOEH tDF WE# tOH High Z DQ6/DQ2 tBUSY Valid Status Valid Status (first read) (second read) Valid Status Valid Data (stops toggling) RY/BY# Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle. 21359C-21 Figure 18. 33 Toggle Bit Timings (During Embedded Algorithms) Am29LV116B PRELIMINARY AC CHARACTERISTICS Enter Embedded Erasing Erase Suspend Erase WE# Enter Erase Suspend Program Erase Suspend Program Erase Suspend Read Erase Resume Erase Erase Suspend Read Erase Complete DQ6 DQ2 Note: The system can use OE# or CE# to toggle DQ2/DQ6. DQ2 toggles only when read at an address within an erase-suspended sector. 21359C-22 Figure 19. DQ2 vs. DQ6 Temporary Sector Unprotect Parameter JEDEC Std. Description tVIDR VID Rise and Fall Time (See Note) tRSP RESET# Setup Time for Temporary Sector Unprotect All Speed Options Unit Min 500 ns Min 4 µs Note: Not 100% tested. 12 V RESET# 0 or 3 V tVIDR tVIDR Program or Erase Command Sequence CE# WE# tRSP RY/BY# 21359C-23 Figure 20. Temporary Sector Unprotect Timing Diagram Am29LV116B 34 PRELIMINARY AC CHARACTERISTICS VID VIH RESET# SA, A6, A1, A0 Valid* Valid* Sector Protect/Unprotect Data 60h Valid* Verify 60h 40h Status Sector Protect: 100 µs Sector Unprotect: 10 ms 1 µs CE# WE# OE# Note: For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0. 21359C-24 Figure 21. 35 Sector Protect/Unprotect Timing Diagram Am29LV116B PRELIMINARY AC CHARACTERISTICS Alternate CE# Controlled Erase/Program Operations Parameter JEDEC Std. Description 80R 90 120 Unit tAVAV tWC Write Cycle Time (Note 1) Min 80 90 120 ns tAVEL tAS Address Setup Time Min tELAX tAH Address Hold Time Min 45 45 50 ns tDVEH tDS Data Setup Time Min 35 45 50 ns tEHDX tDH Data Hold Time Min 0 ns tOES Output Enable Setup Time Min 0 ns tGHEL tGHEL Read Recovery Time Before Write (OE# High to WE# Low) Min 0 ns tWLEL tWS WE# Setup Time Min 0 ns tEHWH tWH WE# Hold Time Min 0 ns tELEH tCP CE# Pulse Width Min tEHEL tCPH CE# Pulse Width High Min 30 ns tWHWH1 tWHWH1 Programming Operation (Note 2) Typ 9 µs tWHWH2 tWHWH2 Sector Erase Operation (Note 2) Typ 0.7 sec 0 35 35 ns 50 ns 1. Not 100% tested. 2. See the “Erase and Programming Performance” section for more information. Am29LV116B 36 PRELIMINARY AC CHARACTERISTICS 555 for program 2AA for erase PA for program SA for sector erase 555 for chip erase Data# Polling Addresses PA tWC tAS tAH tWH WE# tGHEL OE# tWHWH1 or 2 tCP CE# tWS tCPH tBUSY tDS tDH DQ7# Data tRH A0 for program 55 for erase DOUT PD for program 30 for sector erase 10 for chip erase RESET# RY/BY# Note: PA = program address, PD = program data, DQ7# = complement of the data written to the device, DOUT = data written to the device. Figure indicates the last two bus cycles of the command sequence. 21359C-25 Figure 22. 37 Alternate CE# Controlled Write Operation Timings Am29LV116B PRELIMINARY ERASE AND PROGRAMMING PERFORMANCE Parameter Typ (Note 1) Max (Note 2) Unit Sector Erase Time 0.7 15 s Chip Erase Time 25 Byte Programming Time 9 300 µs Chip Programming Time (Note 3) 18 54 s s Comments Excludes 00h programming prior to erasure (Note 4) Excludes system level overhead (Note 5) Notes: 1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC, 1,000,000 cycles. Additionally, programming typicals assume checkerboard pattern. 2. Under worst case conditions of 90°C, VCC = 2.7 V, 1,000,000 cycles. 3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes program faster than the maximum program times listed. 4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure. 5. System-level overhead is the time required to execute the four- or two-bus-cycle sequence for the program command. See Table 9 for further information on command definitions. 6. The device has a guaranteed minimum erase and program cycle endurance of 1,000,000 cycles per sector. LATCHUP CHARACTERISTICS Description Min Max Input voltage with respect to VSS on all pins except I/O pins (including A9, OE#, and RESET#) –1.0 V 12.5 V Input voltage with respect to VSS on all I/O pins –1.0 V VCC + 1.0 V –100 mA +100 mA VCC Current Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time. TSOP PIN CAPACITANCE Parameter Symbol Parameter Description Test Setup Typ Max Unit CIN Input Capacitance VIN = 0 6 7.5 pF COUT Output Capacitance VOUT = 0 8.5 12 pF CIN2 Control Pin Capacitance VIN = 0 7.5 9 pF Notes: 1. Sampled, not 100% tested. 2. Test conditions TA = 25°C, f = 1.0 MHz. DATA RETENTION Parameter Test Conditions Min Unit 150°C 10 Years 125°C 20 Years Minimum Pattern Data Retention Time Am29LV116B 38 PRELIMINARY PHYSICAL DIMENSIONS* TS 040—40-Pin Standard TSOP (measured in millimeters) 0.95 1.05 Pin 1 I.D. 1 40 9.90 10.10 0.50 BSC 20 21 0.05 0.15 18.30 18.50 19.80 20.20 0.08 0.20 0.10 0.21 1.20 MAX 0˚ 5˚ 0.25MM (0.0098") BSC 16-038-TSOP-1_AC TS 040 4-25-96 lv 0.50 0.70 * For reference only. BSC is an ANSI standard for Basic Space Centering. TSR040—40-Pin Reverse TSOP (measured in millimeters) 1.05 Pin 1 I.D. 1 40 9.90 10.10 0.50 BSC 20 21 0.05 0.15 18.30 18.50 19.80 20.20 0.08 0.20 0.10 0.21 1.20 MAX 0.25MM (0.0098") BSC 0˚ 5˚ 0.50 0.70 * For reference only. BSC is an ANSI standard for Basic Space Centering. 39 Am29LV116B 16-038-TSOP-1_AC TSR040 4-25-96 lv PRELIMINARY REVISION SUMMARY Revision B AC Characteristics Global Erase/Program Operations; Alternate CE# Controlled Erase/Program Operations: Corrected the notes reference for tWHWH1 and tWHWH2. These parameters are 100% tested. Corrected the note reference for tVCS. This parameter is not 100% tested. Deleted SO package from data sheet. Revision C Alternate CE# Controlled Erase/Program Operations Temporary Sector Unprotect Table Changed tCP from 45 to 35 ns on 80R and 90 speed options. Added note reference for tVIDR. This parameter is not 100% tested. Revision C+1 Figure 21, Sector Protect/Unprotect Timing Diagram Global Changed data sheet status to Preliminary. A valid address is not required for the first write cycle; only the data 60h. Reset Command Erase and Programming Performance Deleted the last paragraph in this section. In Note 2, the worst case endurance is now 1 million cycles. Revision C+2 Figure 1, In-System Sector Protect/Unprotect Algorithms In the sector protect algorithm, added a “Reset PLSCNT=1” box in the path from “Protect another sector?” back to setting up the next sector address. Trademarks Copyright © 1998 Advanced Micro Devices, Inc. All rights reserved. AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc. ExpressFlash is a trademark of Advanced Micro Devices, Inc. Product names used in this publication are for identification purposes only and may be trademarks of their respective companies. Am29LV116B 40