0603 CHIP INDUCTOR Chip Inductors for Critical Applications CP312RAB ■ Higher inductance values than other 0603 inductors ■ Ferrite construction for high current handling ■ Inductance values: 47 nH – 22 µH; 5% and 2% tolerance Typical L vs Frequency Core material Ceramic/Ferrite Terminations RoHS compliant silver-palladium-platinum-glass frit. Weight 4.8 – 6.2 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +100°C with derated current Storage temperature Component: –55°C to +100°C. Tape and reel packaging: –55°C to +80°C 100000 Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +50 to +150 ppm/°C Inductance (nH) 10000 Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) 8200 nH Packaging 2000 per 7″ reel. Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.1 mm pocket depth 3300 nH PCB washing Only pure water or alcohol recommended 1000 nH 1000 330 nH Irms Derating 100 nH 100 120 110 100 10 100 1000 Frequency (MHz) Typical Q vs Frequency 35 30 80 70 60 50 40 30 20 10 8200 nH 25 Q factor 90 25°C 1 Percent of rated Irms 10 0 -40 1000 nH 20 -20 0 20 40 60 80 100 120 Ambient temperature (°C) 100 nH 3300 nH 330 nH 15 10 5 0 0.1 1 10 100 Frequency (MHz) ® Specifications subject to change without notice. Please check our website for latest information. 1102 Silver Lake Road Cary IL 60013 © Coilcraft, Inc. 2012 Document CP264-1 Phone 800-981-0363 Fax 847-639-1508 Revised 07/11/12 E-mail [email protected] Web www.coilcraft-cps.com 0603 CHIP INDUCTOR CP312RAB Series (0603) Part number1 CP312RAB47N_LZ CP312RAB51N_LZ CP312RAB72N_LZ CP312RAB101_LZ CP312RAB121_LZ CP312RAB151_LZ CP312RAB181_LZ CP312RAB241_LZ CP312RAB271_LZ CP312RAB331_LZ CP312RAB391_LZ CP312RAB471_LZ CP312RAB561_LZ CP312RAB681_LZ CP312RAB781_LZ CP312RAB821_LZ CP312RAB102_LZ CP312RAB122_LZ CP312RAB152_LZ CP312RAB182_LZ CP312RAB222_LZ CP312RAB272_LZ CP312RAB332_LZ CP312RAB392_LZ CP312RAB472_LZ CP312RAB562_LZ CP312RAB682_LZ CP312RAB782_LZ CP312RAB822_LZ CP312RAB103_LZ CP312RAB153_LZ CP312RAB183_LZ CP312RAB223_LZ Inductance2 (nH) PercentSRF min4 DCR max5 tolerance Q min3 (MHz) (Ohms) 47 @ 7.9 MHz 51 @ 7.9 MHz 72 @ 7.9 MHz 100 @ 7.9 MHz 120 @ 7.9 MHz 150 @ 7.9 MHz 180 @ 7.9 MHz 240 @ 7.9 MHz 270 @ 7.9 MHz 330 @ 7.9 MHz 390 @ 7.9 MHz 470 @ 7.9 MHz 560 @ 7.9 MHz 680 @ 7.9 MHz 780 @ 7.9 MHz 820 @ 7.9 MHz 1000 @ 7.9 MHz 1200 @ 7.9 MHz 1500 @ 7.9 MHz 1800 @ 7.9 MHz 2200 @ 7.9 MHz 2700 @ 7.9 MHz 3300 @ 7.9 MHz 3900 @ 7.9 MHz 4700 @ 7.9 MHz 5600 @ 7.9 MHz 6800 @ 7.9 MHz 7800 @ 7.9 MHz 8200 @ 7.9 MHz 10,000 @ 2.5 MHz 15,000 @ 2.5 MHz 18,000 @ 2.5 MHz 22,000 @ 2.5 MHz 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 5,2 12 @ 7.9 MHz 12 @ 7.9 MHz 12 @ 7.9 MHz 12 @ 7.9 MHz 12 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 15 @ 7.9 MHz 12 @ 2.5 MHz 20 @ 2.5 MHz 20 @ 2.5 MHz 22 @ 2.5 MHz 1. When ordering, please specify tolerance, termination and testing codes: CP312RAB822JLZ Tolerance: G = 2% J = 5% Termination: L = RoHS compliant silver-palladium-platinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Testing: Z = COTS H = Screening per Coilcraft CP-SA-10001 2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/HP 4286A impedance analyzer or equivalent with Coilcraft-provided correlation pieces. 3. Q measured using an Agilent/HP 4291A with an Agilent/HP 16197A test fixture or equivalents. 4. SRF measured using an Agilent/HP 8753ES network analyzer or equivalent and a Coilcraft SMD-D test fixture. 5. DCR measured on a Keithley 580 micro-ohmmeter or equivalent and a Coilcraft CCF1010 test fixture. 6. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. ® 0.075 0.075 0.12 0.13 0.15 0.15 0.15 0.16 0.30 0.46 0.51 0.62 0.44 0.52 0.83 0.69 0.81 0.87 0.96 1.1 1.2 1.5 1.5 1.6 2.1 2.6 3.1 3.5 3.6 4.8 7.1 7.6 8.81 D F A E terminal Color code Overall width 1.40 1.00 1.40 1.40 1.40 1.30 1.30 0.95 0.71 0.56 0.50 0.42 0.55 0.47 0.39 0.40 0.40 0.37 0.35 0.35 0.32 0.28 0.28 0.28 0.26 0.24 0.20 0.20 0.19 0.18 0.17 0.16 0.13 Black Violet Brown Red Orange Yellow Green Violet Gray White Black Brown Red Orange Yellow Green Blue Violet Gray White Black Brown Red Orange Yellow Green Black Blue Violet Gray White Brown Black B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B1 B2 B1 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 B2 C B overall H Pick and place material I G J F I Terminal wraparound: approx 0.008/0,20 both ends Suggested Recommended Land Pattern Pattern Land AC D max B max ref E F G H I J See 0.044 0.015 0.030 0.013 0.034 0.040 0.025 0.025 inches 0.071 note 2 1,12 0,38 0,76 0,33 0,86 1,02 0,64 0,64 mm 1,80 Notes: 1. Dimensions are before optional solder application. For maximum overall dimensions including solder, add 0.0025 in / 0,064 mm to B and 0.006 in / 0,15 mm to A and C. 2. B1 = 0.040 ±0.004 in / 1,016 ±0,102 mm B2 = 0.046 ±0.004 in / 1,169 ±0,102 mm Specifications subject to change without notice. Please check our website for latest information. 1102 Silver Lake Road Cary IL 60013 © Coilcraft, Inc. 2012 1500 1400 1400 1150 1100 1050 950 800 775 725 620 540 525 260 460 410 190 160 100 80 68 60 42 40 34 32 31 28 26 25 23 22 19 Imax (A) Document CP264-2 Phone 800-981-0363 Fax 847-639-1508 Revised 07/11/12 E-mail [email protected] Web www.coilcraft-cps.com