Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] ACT part : ACTF410A/410.0/F11 This specification covers the characteristics of the 410.000MHz SAW Filter. ( For Mobile Radio – FRS & PMR ) 1. Package Dimension (F-11) Pin Configuration 1 Input / Output 4 Output / Input 2/3 Case Ground Dimensions Data (unit: mm) A 11.0±0.3 B 4.5±0.3 C 3.2±0.3 D 0.45±0.1 E 5.0±0.5 F 2.54±0.2 3. Test Circuit In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered - Registration number 6830/2 For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue : 1 C1 Date : SEPT 04 Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] 4. Typical Frequency Response 5. Performance 5-1.Maximum Ratings Rating RF Power Dissipation Value P 0dBm DC Voltage VDC 10V AC Voltage VAC 10V50Hz/60Hz Operation Temperature Topr -20 to +60°C Storage Temperature Tstg -40 to +85°C In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered - Registration number 6830/2 For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue : 1 C1 Date : SEPT 04 Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] 5-2.Electronic Characteristics Characteristics Minimum Typical Maximum Units Center Frequency fC -- 410.000 -- MHz Usable Pass Band BW -- ±3.0 -- MHz Insertion Loss IL -- 3.0 4.5 dB 36 42 42 50 -- dB -- -- 2.0 dB within fC±3.0MHz Absolute Attenuation out of fC -20.0MHz out of fC -25.0MHz α Pass Band Ripple within fC±3.0MHz Δα Input and Output Impedance (Nominal) 50Ω//0pF iCAUTION: Electrostatic Sensitive Device. Observe precautions for handling! 1. 2. 3. 4. 5. 6. The frequency f C is defined as the midpoint between the 3dB frequencies. Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture that is connected to a 50Ω test system with VSWR≤1.2:1. The test fixture L and C are adjusted for minimum insertion loss at the filter center frequency, f C. Note that insertion loss, bandwidth, and passband shape are dependent on the impedance matching component values and quality. Unless noted otherwise, specifications apply over the entire specified operating temperature range. The specifications of this device are based on the test circuit shown above and subject to change or obsolescence without notice. All equipment designs utilizing this product must be approved by the appropriate government agency prior to manufacture or sale. Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications, processes and circuits implemented within components or assemblies. In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered - Registration number 6830/2 For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com Issue : 1 C1 Date : SEPT 04