Film Capacitors – Power Factor Correction Power Factor Controller Series/Type: Ordering code: BR7000-I B44066R7012E230/B44066R7112E230 Date: Version: March 2013 4 Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the table and then change the color to "white". This ensures that the table disappears (invisible) for the customer PDF. Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it! Identification/Classification 1 (header 1 + top left bar): Film Capacitors – Power Factor Correction Identification/Classification 2 (header 2 + bottom left header bar): Power Factor Controller Ordering code: (top right header bar) B44066R7012E230/B44066R7112E230 Series/Type: (top right header bar) BR7000-I Preliminary data (optional): (if necessary) Department: FILM P PM LMP Date: March 2013 Version: 4 EPCOS AG 2013. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Film Capacitors – Power Factor Correction Power Factor Controller B44066R7012E230/B44066R7112E230 BR7000-I Characteristics 12 – 13 switching outputs 20 pre-programmed control series Control series editor Full graphic display 128 x 64 dots Plain language menu 4-quadrant-operation Automatic initialization Display of multiple grid parameters Display of harmonics Display of distortion factor THD-V/THD-I Display and control of temperature Monitoring of capacitor current Storage of maximum values Storage of switching operations and times Manual and automatic operation Zero voltage cut-off Various error messages/alarm rely Error storage Test run of system with error analysis Interface RS485 optional Panel mounting 144 x 144 x 55 mm Inputs Operation voltage: 110 … 230 V ~ +/- 15% Measuring voltage: 30 … 440 V ~ (L-N) / 50 … 760 V ~ (L-L) Current: X:1A / X:5A Additional external input (110…230V) - optional Outputs 12 relay outputs for capacitor 1 relay output (message/alarm/fan) 1 message relay (free programmable) - optional FILM P PM LMP Please read Cautions and warnings and Important notes at the end of this document. March 2013 Page 2 of 6 Film Capacitors – Power Factor Correction Power Factor Controller B44066R7012E230/B44066R7112E230 BR7000-I Measuring and display of following grid parameters Voltage, current, frequency Active, reactive and apparent power Power factor, missing reactive power Energy Harmonics of voltage (up to 19th) Harmonic of current (up to 19th) TDH-V, THD-I Temperature Well-arranged display of power factor and actual status of switching outputs Display and storage of maximum values, switching operations and operation time Display of harmonics as bar chart Operation Graphic display 164 x 64 dots with 8 lines maximum Plain language menu in ten languages Optimum navigation in the menus via return (ESCAPE) button HELP-button for interactive help text Connection FILM P PM LMP Please read Cautions and warnings and Important notes at the end of this document. March 2013 Page 3 of 6 Film Capacitors – Power Factor Correction Power Factor Controller B44066R7012E230/B44066R7112E230 BR7000-I Technical data and specifications Operating voltage 110 … 230 V ~ +/- 15 %, 50 and 60 Hz Measuring voltage 30 … 440 V ~ (L-N); 50 … 760 V ~ (L-L); 50/60 Hz Measuring current X: 5 A / X: 1 A, selectable Power consumption < 5 VA Sensitivity 50 mA/10 mA Switching outputs Relay outputs for capacitor branches 12 Alarm relay 1 Switching power of relays 250 V AC, 1000 W Number of active outputs Programmable Version BR7000-I/S485 Interface RS485, for usage with evaluation software BR7000SOFT, included in the delivery One freely programmable external input, e.g. for 2nd parameter set Additional freely programmable message relay Operation and display Display Illuminated full graphic display 128 x 64 dots Menu languages CZ/EN/ES/FR/GER/NL/PL/PT/RU/TR Freely editable control series 1 via Editor Control Control principle Sequential switching, circle switching, intelligent switching behavior, 4-quadrant operation Automatic initialization/test run Possible Target cos-φ 0.3 inductive up to 0.3 capacitive adjustable Switch on time Selectable from 1 sec. to 20 min. Switch off time Selectable from 1 sec. to 20 min. Discharge time Selectable from 1 sec. to 20 min. Manual operation Yes Fixed steps/skip steps Programmable Zero voltage release Standard Display/display functions Display of grid parameters Cos-φ, V, I , F, W, Q, P, S, ΔQ, THD-V, THD-I Display of harmonics 3rd to 19th harmonics of V and I Accuracy Current/voltage: 1% Active, apparent and reactive power: 2% Integrated help function Context dependent FILM P PM LMP Please read Cautions and warnings and Important notes at the end of this document. March 2013 Page 4 of 6 Film Capacitors – Power Factor Correction Power Factor Controller B44066R7012E230/B44066R7112E230 BR7000-I Storage function Storage of maximum values Voltage, current, active/reactive/apparent power, temperature, THD-V, THD-I Storage of switching operations Each output can be reset separately Storage of operation time Each capacitor can be reset separately Error storage Error register in plain language Temperature monitoring Monitoring Automatic step switch off Temperature measuring range -30 … +100 °C Casing Panel mounted instrument DIN 43700, 144 x 144 x 55 mm Weight 1 kg Ambient operating temperature -20 °C … +60 °C Protection class accord. DIN 40050 Front: IP54, rear: IP 20 Safety regulations IEC 601010-1:2001, EN61010-1:2001 Interference resistance EN50082-1:1995 EMC-interference IEC61000-4-2: 8 kV IEC61000-4-4: 4 kV Ordering codes BR7000-I (without interface) BR7000-I/S485 (with interface RS485) B44066R7012E230 B44066R7112E230 Cautions and Warnings Controller hunting: When putting the capacitor bank into operation, it is required to avoid needless switching cycles (means permanent switching on and off of steps without significant change of consumer load). This so called “controller hunting“ would increase the number of switching operations of the connected contactors and capacitors and decrease the expected life cycle (wear out) and, in worst case, capacitor bursting and fire, etc . This can be avoided by a proper programming of the BR7000-I with the actual system parameters (current transformer prim. and sec., first kvar step, control series, switching time). U Please read cautions information about PFC capacitors and cautions as well as installation and maintenance instructions in the actual version of the Product Profile Power Factor Correction to ensure optimum performance and prevent products from failing, and in worst case, bursting and fire, etc. The actual Product Profile is available at www.epcos.com/publications. Information given in the PFC-product profile and values given in the data sheet reflect typical specifications. You are kindly requested to approve our product specifications or request our approval for your specification before ordering. Note For detailed information about PFC capacitors and cautions, refer to the latest version of EPCOS PFC Product Profile. FILM P PM LMP Please read Cautions and warnings and Important notes at the end of this document. March 2013 Page 5 of 6 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 6 of 6