CAT28C512/513 512K-Bit CMOS PARALLEL EEPROM FEATURES ■ Fast Read Access Times: 120/150 ns ■ Automatic Page Write Operation: –1 to 128 Bytes in 5ms –Page Load Timer ■ Low Power CMOS Dissipation: –Active: 50 mA Max. –Standby: 200 µA Max. ■ End of Write Detection: –Toggle Bit DATA Polling –DATA ■ Simple Write Operation: –On-Chip Address and Data Latches –Self-Timed Write Cycle with Auto-Clear ■ Hardware and Software Write Protection ■ Fast Write Cycle Time: ■ 100,000 Program/Erase Cycles –5ms Max ■ 100 Year Data Retention ■ CMOS and TTL Compatible I/O ■ Commercial, Industrial and Automotive Temperature Ranges DESCRIPTION The CAT28C512/513 is manufactured using Catalyst’s advanced CMOS floating gate technology. It is designed to endure 100,000 program/erase cycles and has a data retention of 100 years. The device is available in JEDEC approved 32-pin DIP, PLCC and TSOP packages. The CAT28C512/513 is a fast,low power, 5V-only CMOS parallel EEPROM organized as 64K x 8-bits. It requires a simple interface for in-system programming. On-chip address and data latches, self-timed write cycle with auto-clear and VCC power up/down write protection eliminate additional timing and protection hardware. DATA Polling and Toggle status bits signal the start and end of the self-timed write cycle. Additionally, the CAT28C512/513 features hardware and software write protection. BLOCK DIAGRAM A7–A15 ADDR. BUFFER & LATCHES ROW DECODER VCC INADVERTENT WRITE PROTECTION HIGH VOLTAGE GENERATOR CE OE WE CONTROL 128 BYTE PAGE REGISTER I/O BUFFERS TIMER A0–A6 65,536 x 8 EEPROM ARRAY DATA POLLING AND TOGGLE BIT ADDR. BUFFER & LATCHES © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice I/O0–I/O7 COLUMN DECODER 1 Doc. No. MD-1007, Rev. I CAT28C512/513 PIN CONFIGURATION 15 16 A13 A8 A9 A11 OE A10 CE I/O7 A2 A1 A0 I/O0 I/O6 I/O5 I/O4 I/O3 A13 VCC WE A15 A7 A12 NC NC VCC WE A12 A15 NC 4 3 2 1 32 31 30 5 29 6 28 7 27 8 26 CAT28C512 9 25 TOP VIEW 10 24 11 23 12 22 13 21 14 15 16 17 18 19 20 A7 A6 A5 A4 A3 4 3 2 1 32 31 30 A14 A13 A6 A5 5 6 29 28 A8 A9 A4 A3 A11 OE A10 A2 A1 A0 7 8 9 10 27 26 25 24 CE I/O7 NC I/O0 CAT28C513 TOP VIEW 11 23 12 22 13 21 14 15 16 17 18 19 20 A8 A9 A11 NC OE A10 CE I/O7 I/O6 NC I/O3 I/O4 I/O5 I/O1 I/O2 VSS 30 29 28 27 26 25 24 23 22 21 20 19 18 17 VCC WE NC A14 I/O1 I/O2 VSS A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 32 31 I/O6 A15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 I/O1 I/O2 VSS I/O3 I/O4 I/O5 NC NC PLCC Package (N, G) PLCC Package (N, G) A14 DIP Package (L) TSOP Package (8mmx20mm) (T, H) A11 A9 A8 A13 A14 NC WE VCC NC NC A15 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 CAT28C512 TOP VIEW OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 Vss I/O2 I/O1 I/O0 A0 A1 A2 A3 PIN FUNCTIONS Pin Name Function Pin Name Function A0–A15 Address Inputs WE Write Enable I/O0–I/O7 Data Inputs/Outputs VCC 5V Supply CE Chip Enable VSS Ground OE Output Enable NC No Connect Doc. No. MD-1007, Rev. I 2 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT28C512/513 ABSOLUTE MAXIMUM RATINGS* *COMMENT Temperature Under Bias ................. –55°C to +125°C Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions outside of those listed in the operational sections of this specification is not implied. Exposure to any absolute maximum rating for extended periods may affect device performance and reliability. Storage Temperature ....................... –65°C to +150°C Voltage on Any Pin with Respect to Ground(2) ........... –2.0V to +VCC + 2.0V VCC with Respect to Ground ............... –2.0V to +7.0V Package Power Dissipation Capability (Ta = 25°C) ................................... 1.0W Lead Soldering Temperature (10 secs) ............ 300°C Output Short Circuit Current(3) ........................ 100 mA RELIABILITY CHARACTERISTICS Symbol Parameter Min Max. Units Test Method 100,000 Cycles/Byte MIL-STD-883, Test Method 1033 NEND(1) Endurance TDR(1) Data Retention 100 Years MIL-STD-883, Test Method 1008 VZAP(1) ESD Susceptibility 2000 Volts MIL-STD-883, Test Method 3015 ILTH(1)(4) Latch-Up 100 mA JEDEC Standard 17 D.C. OPERATING CHARACTERISTICS VCC = 5V ±10%, unless otherwise specified. Limits Symbol Parameter Min Typ Max. Units Test Conditions ICC VCC Current (Operating, TTL) 50 mA CE = OE = VIL, f=6MHz All I/O’s Open ICCC(5) VCC Current (Operating, CMOS) 25 mA CE = OE = VILC, f=6MHz All I/O’s Open ISB VCC Current (Standby, TTL) 3 mA CE = VIH, All I/O’s Open ISBC(6) VCC Current (Standby, CMOS) 200 µA CE = VIHC, All I/O’s Open ILI Input Leakage Current -10 10 µA VIN = GND to VCC ILO Output Leakage Current -10 10 µA VOUT = GND to VCC, CE = VIH VIH(6) High Level Input Voltage 2 VCC +0.3 V VIL(5) Low Level Input Voltage -1 0.8 V VOH High Level Output Voltage 2.4 VOL Low Level Output Voltage VWI Write Inhibit Voltage 0.4 3.5 V IOH = –400µA V IOL = 2.1mA V Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns. (3) Output shorted for no more than one second. No more than one output shorted at a time. (4) Latch-up protection is provided for stresses up to 100mA on address and data pins from –1V to VCC +1V. (5) VILC = –0.3V to +0.3V. (6) VIHC = VCC –0.3V to VCC +0.3V. © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice 3 Doc. No. MD-1007, Rev . I CAT28C512/513 MODE SELECTION Mode CE WE OE Read L H Byte Write (WE Controlled) L Byte Write (CE Controlled) I/O Power L DOUT ACTIVE H DIN ACTIVE L H DIN ACTIVE Standby, and Write Inhibit H X X High-Z STANDBY Read and Write Inhibit X H H High-Z ACTIVE Test Max. Units Conditions Input/Output Capacitance 10 pF VI/O = 0V Input Capacitance 6 pF VIN = 0V CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5V Symbol CI/O (1) CIN(1) A.C. CHARACTERISTICS, Read Cycle VCC=5V + 10%, Unless otherwise specified 28C512/513-12 28C512/513-15 Symbol Parameter Min. Max. Min. Max. tRC Read Cycle Time 120 tCE CE Access Time 120 150 ns tAA Address Access Time 120 150 ns tOE OE Access Time 50 70 ns tLZ(1) CE Low to Active Output 0 0 ns tOLZ(1) OE Low to Active Output 0 0 ns tHZ(1)(2) CE High to High-Z Output 50 50 ns tOHZ(1)(2) OE High to High-Z Output 50 50 ns tOH(1) Output Hold from Address Change 150 0 Units ns 0 ns Power-Up Timing Symbol Parameter tPUR (1) Power-up to Read Operation tPUW (2) Power-up to Write Operation Min. 5 Max Units 100 µs 10 ms Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) Output floating (High-Z) is defined as the state when the external data line is no longer driven by the output buffer. Doc. No. MD-1007, Rev. I 4 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT28C512/513 A.C. CHARACTERISTICS, Write Cycle VCC=5V+10%, unless otherwise specified 28C512/513-12 28C512/513-15 Min. Max. Min. Max. Units Symbol Parameter tWC Write Cycle Time tAS Address Setup Time 0 0 ns tAH Address Hold Time 50 50 ns tCS CE Setup Time 0 0 ns CE Hold Time 0 0 ns CE Pulse Time 100 100 ns tOES OE Setup Time 0 0 ns tOEH OE Hold Time 0 0 ns tWP(3) WE Pulse Width 100 100 ns tDS Data Setup Time 50 50 ns tDH Data Hold Time 0 0 ns tINIT(1) Write Inhibit Period After Power-up 5 10 5 10 ms 0.1 100 0.1 100 µs tCH tCW (3) 5 tBLC(1)(4) Byte Load Cycle Time 5 ms Figure 1. A.C. Testing Input/Output Waveform(2) VCC - 0.3V 2.0 V INPUT PULSE LEVELS REFERENCE POINTS 0.8 V 0.0 V Figure 2. A.C. Testing Load Circuit (example) 1.3V 1N914 3.3K DEVICE UNDER TEST OUT CL = 100 pF CL INCLUDES JIG CAPACITANCE Note: (1) This parameter is tested initially and after a design or process change that affects the parameter. (2) Input rise and fall times (10% and 90%) < 10 ns. (3) A write pulse of less than 20ns duration will not initiate a write cycle. (4) A timer of duration tBLC max. begins with every LOW to HIGH transition of WE. If allowed to time out, a page or byte write will begin; however a transition from HIGH to LOW within tBLC max. stops the timer. © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice 5 Doc. No. MD-1007, Rev . I CAT28C512/513 Byte Write DEVICE OPERATION A write cycle is executed when both CE and WE are low, and OE is high. Write cycles can be initiated using either WE or CE, with the address input being latched on the falling edge of WE or CE, whichever occurs last. Data, conversely, is latched on the rising edge of WE or CE, whichever occurs first. Once initiated, a byte write cycle automatically erases the addressed byte and the new data is written within 5 ms. Read Data stored in the CAT28C512/513 is transferred to the data bus when WE is held high, and both OE and CE are held low. The data bus is set to a high impedance state when either CE or OE goes high. This 2-line control architecture can be used to eliminate bus contention in a system environment. Figure 3. Read Cycle tRC ADDRESS tCE CE tOE OE VIH tLZ WE tOHZ DATA OUT tHZ tOH tOLZ HIGH-Z DATA VALID DATA VALID tAA Figure 4. Byte Write Cycle [WE Controlled] tWC ADDRESS tAS tAH tCH tCS CE OE tOES tWP tOEH WE tBLC DATA OUT DATA IN HIGH-Z DATA VALID tDS Doc. No. MD-1007, Rev. I tDH 6 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT28C512/513 Page Write to A6 (which can be loaded in any order) during the first and subsequent write cycles. Each successive byte load cycle must begin within tBLC MAX of the rising edge of the preceding WE pulse. There is no page write window limitation as long as WE is pulsed low within tBLC MAX. The page write mode of the CAT28C512/513 (essentially an extended BYTE WRITE mode) allows from 1 to 128 bytes of data to be programmed within a single EEPROM write cycle. This effectively reduces the bytewrite time by a factor of 128. Upon completion of the page write sequence, WE must stay high a minimum of tBLC MAX for the internal automatic program cycle to commence. This programming cycle consists of an erase cycle, which erases any data that existed in each addressed cell, and a write cycle, which writes new data back into the cell. A page write will only write data to the locations that were addressed and will not rewrite the entire page. Following an initial WRITE operation (WE pulsed low, for tWP, and then high) the page write mode can begin by issuing sequential WE pulses, which load the address and data bytes into a 128 byte temporary buffer. The page address where data is to be written, specified by bits A7 to A15, is latched on the last falling edge of WE. Each byte within the page is defined by address bits A0 CE Controlled] Figure 5. Byte Write Cycle [CE tWC ADDRESS tAS tAH tBLC tCW CE tOEH OE tCS tOES tCH WE HIGH-Z DATA OUT DATA IN DATA VALID tDS tDH Figure 6. Page Mode Write Cycle OE CE t BLC t WP WE ADDRESS t WC I/O LAST BYTE BYTE 0 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice BYTE 1 BYTE 2 7 BYTE n BYTE n+1 BYTE n+2 Doc. No. MD-1007, Rev . I CAT28C512/513 DATA Polling Toggle Bit DATA polling is provided to indicate the completion of write cycle. Once a byte write or page write cycle is initiated, attempting to read the last byte written will output the complement of that data on I/O7 (I/O0–I/O6 are indeterminate) until the programming cycle is complete. Upon completion of the self-timed write cycle, all I/O’s will output true data during a read cycle. In addition to the DATA Polling feature of the CAT28C512/ 513, the device offers an additional method for determining the completion of a write cycle. While a write cycle is in progress, reading data from the device will result in I/ O6 toggling between one and zero. However, once the write is complete, I/O6 stops toggling and valid data can be read from the device. Figure 7. DATA Polling ADDRESS CE WE tOEH tOES tOE OE tWC I/O7 DIN = X DOUT = X D OUT = X Figure 8. Toggle Bit WE CE tOEH tOES tOE OE I/O6 (1) (1) tWC Note: (1) Beginning and ending state of I/O6 is indeterminate. Doc. No. MD-1007, Rev. I 8 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT28C512/513 HARDWARE DATA PROTECTION The following is a list of hardware data protection features that are incorporated into the CAT28C512/513. (4) Noise pulses of less than 20 ns on the WE or CE inputs will not result in a write cycle. (1) VCC sense provides for write protection when VCC falls below 3.5V min. SOFTWARE DATA PROTECTION The CAT28C512/513 features a software controlled data protection scheme which, once enabled, requires a data algorithm to be issued to the device before a write can be performed. The device is shipped from Catalyst with the software protection NOT ENABLED (the CAT28C512/513 is in the standard operating mode). (2) A power on delay mechanism, tINIT (see AC characteristics), provides a 5 to 10 ms delay before a write sequence, after VCC has reached 3.5V min. (3) Write inhibit is activated by holding any one of OE low, CE high or WE high. Figure 9. Write Sequence for Activating Software Data Protection WRITE DATA: ADDRESS: WRITE DATA: ADDRESS: WRITE DATA: ADDRESS: Figure 10. Write Sequence for Deactivating Software Data Protection WRITE DATA: AA ADDRESS: 5555 WRITE DATA: 55 ADDRESS: 2AAA WRITE DATA: A0 ADDRESS: 5555 (1) SOFTWARE DATA (12) PROTECTION ACTIVATED WRITE DATA: WRITE DATA: XX WRITE DATA: TO ANY ADDRESS ADDRESS: WRITE LAST BYTE TO LAST ADDRESS W R I T E DATA : ADDRESS: ADDRESS: AA 5555 55 2AAA 80 5555 AA 5555 55 2AAA 20 5555 Note: (1) Write protection is activated at this point whether or not any more writes are completed. Writing to addresses must occur within tBLC Max., after SDP activation. © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice 9 Doc. No. MD-1007, Rev . I CAT28C512/513 To activate the software data protection, the device must be sent three write commands to specific addresses with specific data (Figure 9). This sequence of commands (along with subsequent writes) must adhere to the page write timing specifications (Figure 11). Once this is done, all subsequent byte or page writes to the device must be preceded by this same set of write commands. The data protection mechanism is activated until a deactivate sequence is issued regardless of power on/off transitions. This gives the user added inadvertent write protection on power-up in addition to the hardware protection provided. To allow the user the ability to program the device with an EEPROM programmer (or for testing purposes) there is a software command sequence for deactivating the data protection. The six step algorithm (Figure 10) will reset the internal protection circuitry, and the device will return to standard operating mode (Figure 12 provides reset timing). After the sixth byte of this reset sequence has been issued, standard byte or page writing can commence. Figure 11. Software Data Protection Timing DATA ADDRESS AA 5555 55 2AAA tWC A0 5555 BYTE OR PAGE CE tWP tBLC WRITES ENABLED WE Figure 12. Resetting Software Data Protection Timing DATA ADDRESS AA 5555 55 2AAA 80 5555 AA 5555 55 2AAA 20 5555 tWC SDP RESET CE DEVICE UNPROTECTED WE Doc. No. MD-1007, Rev. I 10 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice CAT28C512/513 (1) EXAMPLE OF ORDERING INFORMATION Prefix Device # CAT 28C512 Optional Company ID Suffix N -15 I Temperature Range Blank = Commercial (0°C to +70°C) I = Industrial (-40°C to +85°C) (4) A = Automotive (-40°C to +105°C) Product Number 28C512 28C513 Package N: PLCC(2) T: TSOP (8mmx20mm)(2) L: PDIP (Lead free, Halogen free) (3) G: PLCC (Lead free, Halogen free) H: TSOP (8mmx20mm) (Lead free, Halogen free) T Tape & Reel Speed 12: 120ns 15: 150ns ORDERING INFORMATION Orderable Part Numbers (for Pb-Free Devices) CAT28C512G-12T CAT28C513G-12T CAT28C512G-15T CAT28C513G-15T CAT28C512GA-12T CAT28C513GA-12T CAT28C512GA-15T CAT28C513GA-15T CAT28C512GI-12T CAT28C513GI-12T CAT28C512GI-15T CAT28C513GI-15T CAT28C512H-12T CAT28C512H-15T CAT28C512HA-12T CAT28C512HA-15T CAT28C512HI-12T CAT28C512HI-15T CAT28C512L12 CAT28C512L15 CAT28C512LA12 CAT28C512LA15 CAT28C512LI12 CAT28C512LI15 Notes: (1) The device used in the above example is a CAT28C512NI-15T (PLCC, Industrial temperature, 150 ns Access Time, Tape & Reel). (2) Solder-plate (tin-lead) packages, contact Factory for availability. (3) 28C513 is offered only in PLCC package. (4) -40°C to +125°C is available upon request. © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice 11 Doc. No. MD-1007, Rev . I CAT28C512/513 REVISION HISTORY Date Revision Description 19-Apr-04 E Delete data sheet designation Update Block Diagram Update Ordering Information Add Revision History Update Rev Number 17-Nov-04 F Delete T14 and H14 package codes 15-Oct-08 G Eliminate PDIP SnPb package 20-Nov-08 H Change logo and fine print to ON Semiconductor I Update Example of Ordering Information Update Ordering Information table 28-Jul-09 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] Doc. No. MD-1007, Rev. I N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center: Phone: 81-3-5773-3850 12 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice