Chongqing ABF04 Single phase1.0amps. glass passivated bridge rectifier Datasheet

ABF02 THRU ABF10
SINGLE PHASE1.0AMPS. GLASS PASSIVATED BRIDGE RECTIFIERS
FEATURE
ABF
.165(4.2)
.150(3.8)
.Glass passivated junction.
.Ideal for printed circuit board.
.Reliable low cost construction utilizing
molded plastic technique.
.High surge current capability.
.High temperature soldering guaranteed:
260℃/10 seconds at terminals.
-
+
.260(6.60)
.248(6.30)
MECHANICAL DATA
.010(.25)
.006(.15)
.181(4.6)
.173(4.4)
.033(.75)
.022(.55)
.Case Material: “Green” Molding compound,
UL flammability classification rating 94V-0,
“Free halogen”
.Moisture sensitivity level:level 2a,per J-STD-020
.Polarity:Polarity as marked on the body
.Weight: 0.09g (approximately)
.201(5.1)
.193(4.9)
.028(.70)
.020(.50)
.006(.15)
.002(.05)
5°
5°
.030(.75)
.018(.45)
R .004(R .1)
.051(1.3)
M AX
+
~~
Dimensions in inches and (millimeters)
-
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25℃ ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz,resistive or inductive load.
For capacitive load, derate current by 20%
SYM
BOL
Type Number
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC blocking Voltage
Maximum Average Forward rectified Current
@ TA=40℃
ABF02
ABF04
ABF06
ABF08
ABF10
units
200
400
600
800
1000
V
140
280
420
560
700
V
200
400
600
800
1000
V
VRRM
VRMS
VDC
IF(AV)
1.0
IFSM
30
A
Peak Forward Surge Current 8.3ms single half
sine-wave superimposed on rate load (JEDEC
A
method)
Maximum Instantaneous
Forward Voltage
@ IF =1.0A DC
@ IF = 0.5A DC
Maximum DC Reverse Current
at rated DC blocking voltage
@TJ =25°C
@TJ =125°C
I2t Rating for Fusing (t﹤8.3ms)
Typical Junction Capacitance Per Leg (Note1)
Typical Thermal Resistance (Note2)
Storage Temperature
Operating Junction Temperature
1.1
VF
0.95
5.0
IR
100.0
I 2t
CJ
RJC
RJA
TSTG
TJ
μA
3.74
A2Sec
13
pF
22
80
°C /W
-55 to +150
°C
-55 to +150
°C
Note:
1. Measured at 1.0 MHz and applied reverse voltage of 4.0Vdc
2. Thermal resistance junction to case, lead and ambient in accordance with JESD-51.
Unit mounted on glass-epoxy substrate with 1oz/ft2_10x10 mm copper pad per pin with heatsink
-7-
V
RATING AND CHARACTERISTIC CURVES ( ABF02 THRU ABF10 )
10.0
TC
1.0
TA
0.5
Single Phase Half
Wave 60Hz
Resistive or
inductive Load
0
FIG.2-TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
INSTANEOUS FORWARD
CURRENT,(A)
AVERGE FORWARD RECTIFIED
CURRENT,(A)
FIG.1-TYPICAL FORWARD CURRENT DERATING
CURVE
0
AMBIENT,CASE TEMPERTURE,(℃)
1
100
NUMBER OF CYCLES AT 60Hz
TJ=100℃
10
1.0
.1
100
10
TJ=25℃
0
20
40
16
12
8
4
1
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE,(%)
FIG.5-TYPIAL JUNCTION CAPAOTANCE
0
1.4
FIG.4-TYPICAL REVERSE CHARACTERISTICS
INSTANEOUS REVERSE
CURRENT,(μA)
10
JUNCTION CAPACITANCE,(pF)
PEAK FORWARD SURGE
CURRENT,(A)
20
0
1.2
TJ=125℃
8.3ms Single Half
Sine-Wave (JEDEC
Method)
30
1.0
.8
.6
INSTANEOUS FORWARD VOLTAGE,(V)
FIG.3-MAXIMUN NON-REPETITIVE FORWARD
SURGE CURRENT
40
TJ=25℃
Pulse Width=300μs
1% Duty Cycle
.1
.01
200
150
100
50
1.0
10
REVERCE VOLTAGE,(V)
-8-
100
Similar pages