AZ AZ2510 100 AMP LATCHING POWER RELAY FEATURES • • • • • 100 Amp switching Heavy loads to 24000 VA 4 kV dielectric Meets 8 mm creepage Mechanical position indicator which may be also used for manual operation or to actuate a micro-switch • UL, CUR pending CONTACTS GENERAL DATA Arrangement SPST (1 Form A) Ratings Resistive load: Life Expectancy Mechanical Electrical Minimum operations 1 x 106 1 x 104 at 100 A 240 VAC Res. Max. switched power: 3000 W, 24000 VA Max. switched current: 100 A Max. switched voltage: 30 VDC, 400 VAC Set and Reset Pulse Duration 36 ms minimum Set Time (typical) 12 ms at nominal coil voltage Reset Time (typical) 6 ms at nominal coil voltage Rated Load UL, CUR 100 A at 240 VAC, 10k cycles, Resistive Material Silver tin oxide Resistance < 2 milliohms initially (24 V, 1 A voltage drop method) COIL Dielectric Strength 4000 Vrms coil to contact (at sea level for 1 min.) 2000 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Creepage Distance 8 mm Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 70°C (158°F) -40°C (-40°F) to 105°C (221°F) Vibration 0.062" DA at 10–55 Hz Power At Pickup Voltage (typical) Temperature 1.44 W single coil 2.88 W dual coil Shock Operating 10 g, 11 ms, 1/2 sine (no false operation) Non-Operating 100 g, 11 ms, 1/2 sine (no damage) Max. 105°C (2221°F) NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. Enclosure P.B.T. polyester Terminals Tinned copper alloy P. C. (coil), heavy tabs (power) Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Weight 82 grams 3. Specifications subject to change without notice. 4. Allow suitable slack on leads when wiring, and do not subject the terminals to excessive force. 1/21/09W AZ AZ2510 RELAY ORDERING DATA COIL SPECIFICATIONS - Standard Single Coil Nominal Coil VDC 6 12 24 48 Must Operate VDC 4.8 9.6 19.2 38.4 Max. Continuous VDC [1] 10 20 40 80 Coil Resistance ± 10% 16 64 260 1024 ORDER NUMBER Coil Resistance ± 10% 8 32 130 512 ORDER NUMBER AZ2510P1–1A–6D AZ2510P1–1A–12D AZ2510P1–1A–24D AZ2510P1–1A–24D COIL SPECIFICATIONS - Standard Dual Coil Nominal Coil VDC 6 12 24 48 Must Operate VDC 4.8 9.6 19.2 38.4 Max. Continuous VDC [1] 10 20 40 80 AZ2510P2–1A–6D AZ2510P2–1A–12D AZ2510P2–1A–24D AZ2510P2–1A–48D [1] max. continuous voltage should not be applied for more than 30 seconds. MECHANICAL DATA Wiring Diagram 2.372MAX [60.25] 1.782MAX [45.25] 1.421 [36.10] .756 [19.20] 3 4 .512 [13.00] 1.585MAX [40.25] .059 [1.50] 3X.039 [1.00] .197 [5.00] 2.372MAX [60.25] 1.746 [44.35] .876MAX [22.25] 1(-) 1.880MAX [47.75] Set 2(+) Reset 3(-) Dual Coil 2 .243 [6.16] .197 [5.00] .571 [14.50] .197 [5.00] .016 [0.40] 3X.039 [1.00] 3X.028 [0.70] .197 [5.00] 0.329 [8.36] 3X.028 [0.70] 0.571 [14.50] .433 [11.00] 1(-) 2 (+) 3(+) Set (-) Reset Single Coil 2xM6 TOP VIEW BOTTOM VIEW Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 1/21/09W