MORNSUN B1215YS-W2 Miniature sip package Datasheet

B_YS-W2 Series
FIXED INPUT ISOLATED & UNREGULATED
0.25W SINGLE OUTPUT
MINIATURE SIP PACKAGE
FEATURES
multi-country patent protection RoHS
PRODUCT PROGRAM
● Small Footprint
● Miniature SIP Package
● 1KVDC Isolation
● Temperature Range: -40°C to +85°C
● Internal SMD Construction
● Industry Standard Pinout
● No Heat sink Required
● No External Component Required
● PCB Mounting
● RoHS Compliance
Input
Part
Number
Output
Voltage (VDC)
Nominal
Range
3.3
2.97-3.63
B0303YS-W2
Max
Min
3.3
76
7.6
62
B0305YS-W2
5
50
5
65
B0503YS-W2
3.3
76
7.6
62
5
50
5
64
9
28
3
65
12
21
2.1
67
B0515YS-W2
15
17
1.7
65
B1203YS-W2
3.3
76
7.6
62
B1205YS-W2
5
50
5
65
B0505YS-W2
B0509YS-W2
5
4.5-5.5
B0512YS-W2
APPLICATIONS
The B_YS-W2 Series are specially designed
Efficiency
(%, Typ)
Current (mA)
Voltage
(VDC)
9
28
3
66
isolated from the input power supply in a
B1212YS-W2
12
21
2.1
67
distributed power supply system on a circuit
B1215YS-W2
15
17
1.7
66
board.
B2405YS-W2
5
50
5
63
These products apply to:
B2409YS-W2
9
28
3
63
12
21
2.1
65
15
17
1.7
65
for applications where a single power supply is
1)
Where the voltage of the input power supply
is fixed (voltage variation ≤ ±10%);
2)
Where isolation is necessary between input
B1209YS-W2
B2412YS-W2
12
24
10.8-13.2
21.6-26.4
B2415YS-W2
and output (isolation voltage≤1000VDC);
3)
Where the regulation of the output voltage
and the output ripple and noise are not
demanding.
Such as: purely digital circuits, ordinary low
frequency analog circuits and IGBT power device
ISOLATION SPECIFICATIONS
Item
Test Conditions
Isolation voltage
Tested for 1 minute and 1mA max
1000
Min
Typ.
Max
Units
VDC
Isolation resistance
Test at 500VDC
1000
MΩ
driven circuits, etc.
OUTPUT SPECIFICATIONS
Item
Line regulation
MODEL SELECTION
B0505Y S-W2
Test Conditions
Min
Load regulation
O utp ut Voltag e
I npu t Vo lt age
P rod uct S erie s
1.5
For Vin change of 1%(others )
1.2
15
20
10% to 100% load (5V output)
12.8
15
10% to 100% load (9V output)
8.3
10
10% to 100% load (12V output)
6.8
10
10% to 100% load (15V output)
6.3
10
Output voltage accuracy
Units
%
See tolerance envelope graph
Temperature drift
100% full load
MORNSUN Science& Technology co.,Ltd.
Ripple & Noise*
20MHz Bandwidth
50
Address: 2th floor 6th building, Huangzhou Industrial
District, Guangzhou, China
Tel: 86-20-38601850
Fax:86-20-38601272
Http://www.mornsun-power.com
Switching frequency
Full load, nominal input
100
MORNSUN reserves the copyright
Max
For Vin change of 1%(3.3V output)
10% to 100% load (3.3V output)
Rat e d P o wer
P ack age S ty le
Typ.
0.03 %/°C
75 mVp-p
KHz
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
Note:
1.All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load unless
otherwise specified.
2.See the recommended circuits for more details.
Specifications subject to change without notice.
B_YS-W2
A/0-2008
Page 1 of 2
COMMON SPECIFICATION
Item
APPLICATION NOTE
Test Conditions
Min
Typ
Max
Units
95
%
Storage humidity
Operating temperature
-40
85
Storage temperature
-55
125
Temp. rise at full load
15
Lead temperature
1.5mm from case for 10 seconds
Requirement on output load
To ensure this module can operate efficiently
and reliably, During operation, the minimum
output load is not less than 10% of the full load,
°C
and that this product should never be operated
25
under no load! If the actual output power is very
300
Short circuit protection*
small, please connect a resistor with proper
1
Cooling
S
resistance at the output end in parallel to increase
Free air convection
Case material
the load.
Plastic(UL94-V0)
MTBF
3500
Recommended circuit
K hours
Weight
1.6
g
If you want to further decrease the input/output
ripple, an “LC” filtering network may be connected
to the input and output ends of the DC/DC
*Supply voltage must be discontinued at the end of short circuit duration.
converter, see (Figure 1).
L
L
TYPICAL CHARACTERISTICS
+Vo
Vin
DC DC
C
C
GND
0V
(Figure 1)
It should also be noted that the inductance and the
frequency of the “LC” filtering network should be
staggered with the DC/DC frequency to avoid
mutual interference. However, the capacitance of
the output filter capacitor must be proper. If the
capacitance is too big, a startup problem might
arise. It’s not recommended to connect any
Operating Temp.(oC)
external capacitor in the application field .
Output Voltage Regulation and Over-voltage
Protection Circuit
OUTLINE DIMENSIONS & FOOTPRINT DETAILS
The
First Angle Projection
RECOMMENDED FOOTPRINT
Top view,grid:2.54mm(0.1inch),
diameter:1.00mm
simplest
regulation,
device
for
over-voltage
output
and
voltage
over-current
protection is a linear voltage regulator with
overheat protection that is connected to the input
or output end in series (Figure 2).
Vin
+Vout
REG
DC DC
GND
1
2
3
0V
4
REG
Vin
+Vout
DC DC
GND
0V
6.00
(Figure 2)
1
2
Overload Protection
3 4
FOOTPRINT DETAILS
Note:
Unit:mm(inch)
Pin section:0.50*0.30mm(0.020*0.012inch)
Pin toler ances: 0.10mm( 0.004inch)
General tolerances: 0.25mm( 0.010inch)
MORNSUN reserves the copyright
Under normal operating conditions, the output
Pin
Function
circuit of these products has no protection against
1
Vin
overload. The simplest method is to connect a
GN D
3
0V
4
+Vo
Specifications subject to change without notice.
self-recovery fuse in series at the input end or add
a circuit breaker to the circuit.
No parallel connection or plug and play.
B_YS-W2
A/0-2008
Page 2 of 2
Similar pages