[ /Title (CD54 HC405 1, CD74 HC405 1, CD74 HCT40 51, CD74 HC405 2, CD54/74HC4051, CD54/74HCT4051, CD54/74HC4052, CD74HCT4052, CD54/74HC4053, CD74HCT4053 Data sheet acquired from Harris Semiconductor SCHS122I High-Speed CMOS Logic Analog Multiplexers/Demultiplexers November 1997 - Revised July 2004 Features Ordering Information • Wide Analog Input Voltage Range . . . . . . . . . . ±5V Max PART NUMBER • Low “On” Resistance - 70Ω Typical (VCC - VEE = 4.5V) - 40Ω Typical (VCC - VEE = 9V) • Low Crosstalk between Switches TEMP. RANGE (oC) PACKAGE CD74HC4051E -55 to 125 16 Ld PDIP CD74HC4051M -55 to 125 16 Ld SOIC CD74HC4051MT -55 to 125 16 Ld SOIC CD74HC4051M96 -55 to 125 16 Ld SOIC • Fast Switching and Propagation Speeds CD74HC4051NSR -55 to 125 16 Ld SOP • “Break-Before-Make” Switching CD74HC4051PWR -55 to 125 16 Ld TSSOP • Wide Operating Temperature Range . . -55oC to 125oC CD74HC4051PWT -55 to 125 16 Ld TSSOP • CD54HC/CD74HC Types - Operation Control Voltage . . . . . . . . . . . . . . 2V to 6V - Switch Voltage . . . . . . . . . . . . . . . . . . . . . . . 0V to 10V - High Noise Immunity . . . NIL = 30%, NIH = 30% of VCC, VCC = 5V • CD54HCT/CD74HCT Types - Operation Control Voltage . . . . . . . . . . . 4.5V to 5.5V - Switch Voltage . . . . . . . . . . . . . . . . . . . . . . . 0V to 10V - Direct LSTTL Input Logic Compatibility . . . VIL = 0.8V Max, VIH = 2V Min - CMOS Input Compatibility . . . . . II ≤ 1µA at VOL, VOH CD74HC4052E -55 to 125 16 Ld PDIP CD74HC4052M -55 to 125 16 Ld SOIC CD74HC4052MT -55 to 125 16 Ld SOIC CD74HC4052M96 -55 to 125 16 Ld SOIC CD74HC4052NSR -55 to 125 16 Ld SOP CD74HC4052PW -55 to 125 16 Ld TSSOP CD74HC4052PWR -55 to 125 16 Ld TSSOP CD74HC4052PWT -55 to 125 16 Ld TSSOP CD74HC4053E -55 to 125 16 Ld PDIP CD74HC4053M -55 to 125 16 Ld SOIC CD74HC4053MT -55 to 125 16 Ld SOIC CD74HC4053M96 -55 to 125 16 Ld SOIC CD74HC4053NSR -55 to 125 16 Ld SOP CD74HC4053PW -55 to 125 16 Ld TSSOP These devices are digitally controlled analog switches which utilize silicon gate CMOS technology to achieve operating speeds similar to LSTTL with the low power consumption of standard CMOS integrated circuits. CD74HC4053PWR -55 to 125 16 Ld TSSOP CD74HC4053PWT -55 to 125 16 Ld TSSOP CD74HCT4051E -55 to 125 16 Ld PDIP CD74HCT4051M -55 to 125 16 Ld SOIC These analog multiplexers/demultiplexers control analog voltages that may vary across the voltage supply range (i.e. VCC to VEE). They are bidirectional switches thus allowing any analog input to be used as an output and vice-versa. The switches have low “on” resistance and low “off” leakages. In addition, all three devices have an enable control which, when high, disables all switches to their “off” state. CD74HCT4051MT -55 to 125 16 Ld SOIC CD74HCT4051M96 -55 to 125 16 Ld SOIC CD74HCT4052E -55 to 125 16 Ld PDIP CD74HCT4052M -55 to 125 16 Ld SOIC CD74HCT4052MT -55 to 125 16 Ld SOIC CD74HCT4052M96 -55 to 125 16 Ld SOIC CD74HCT4053E -55 to 125 16 Ld PDIP CD74HCT4053M -55 to 125 16 Ld SOIC CD74HCT4053MT -55 to 125 16 Ld SOIC CD74HCT4053M96 -55 to 125 16 Ld SOIC Description Ordering Information PART NUMBER CD54HC4051F3A TEMP. RANGE (oC) -55 to 125 PACKAGE 16 Ld CERDIP CD54HC4052F3A -55 to 125 16 Ld CERDIP CD54HC4053F3A -55 to 125 16 Ld CERDIP CD54HCT4051F3A -55 to 125 16 Ld CERDIP CD74HCT4053PWR -55 to 125 16 Ld TSSOP CD74HCT4053PWT -55 to 125 16 Ld TSSOP NOTE: When ordering, use the entire part number. The suffixes 96 and R denote tape and reel. The suffix T denotes a small-quantity reel of 250. CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright © 2004, Texas Instruments Incorporated 1 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Pinouts CD54HC4051, CD54HCT4051 (CERDIP) CD74HC4051 (PDIP, SOIC, SOP, TSSOP) CD74HCT4051 (PDIP, SOIC) TOP VIEW A4 1 16 VCC A6 2 15 A2 A 3 14 A1 A7 4 13 A0 A5 5 12 A3 E 6 11 S0 VEE 7 10 S1 GND 8 9 S2 CHANNEL IN/OUT COM OUT/IN CHANNEL IN/OUT CD54HC4052 (CERDIP) CD74HC4052 (PDIP, SOIC, SOP, TSSOP) CD74HCT4052 (PDIP, SOIC) TOP VIEW B0 1 16 VCC B2 2 15 A2 COM OUT/IN BN 3 14 A1 CHANNEL IN/OUT B3 4 13 AN COM OUT/IN B1 5 12 A0 E 6 11 A3 VEE 7 10 S0 GND 8 9 S1 CHANNEL IN/OUT CHANNEL IN/OUT CHANNEL IN/OUT ADDRESS SELECT CD54HC4053 (CERDIP) CD74HC4053 (PDIP, SOIC, SOP, TSSOP) CD74HCT4053 (PDIP, SOIC, TSSOP) TOP VIEW B1 1 16 VCC B0 2 15 BN COM OUT/IN C1 3 14 AN COM OUT/IN COM OUT/IN CN 4 13 A1 IN/OUT C0 5 12 A0 E 6 11 S0 VEE 7 10 S1 GND 8 9 S2 CHANNEL IN/OUT 2 CHANNEL IN/OUT CHANNEL IN/OUT ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Functional Diagram of HC/HCT4051 CHANNEL IN/OUT VCC A7 A6 A5 A4 A3 A2 A1 A0 16 4 2 5 1 12 15 14 13 TG TG S0 11 TG S1 TG 10 BINARY TO 1 OF 8 DECODER WITH ENABLE LOGIC LEVEL CONVERSION S2 3 TG 9 TG TG E 6 TG 8 7 GND VEE TRUTH TABLE HC/HCT4051 INPUT STATES ENABLE S2 S1 S0 “ON” CHANNELS L L L L A0 L L L H A1 L L H L A2 L L H H A3 L H L L A4 L H L H A5 L H H L A6 L H H H A7 H X X X None X = Don’t care 3 A COMMON OUT/IN ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Functional Diagram of ’HC4052, CD74HCT4052 A CHANNELS IN/OUT VCC A3 A2 A1 A0 11 15 14 12 16 TG TG TG S1 S0 BINARY TO 1 OF 4 DECODER WITH ENABLE LOGIC LEVEL CONVERSION 9 TG 13 COMMON A OUT/IN TG 3 COMMON B OUT/IN 10 TG E 6 TG TG 8 7 1 5 2 4 GND VEE B0 B1 B2 B3 B CHANNELS IN/OUT TRUTH TABLE ’HC4052, CD74HCT4052 INPUT STATES ENABLE S1 S0 “ON” CHANNELS L L L A0, B0 L L H A1, B1 L H L A2. B2 L H H A3, B3 H X X None X = Don’t care 4 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Functional Diagram of ’HC4053, CD74HCT4053 BINARY TO 1 OF 2 DECODERS WITH ENABLE VCC LOGIC LEVEL CONVERSION 16 IN/OUT C1 C0 B1 B0 A1 A0 3 5 1 2 13 12 TG S0 11 S1 10 14 A COMMON OUT/IN 15 B COMMON OUT/IN 4 C COMMON OUT/IN TG TG TG S2 TG 9 TG E 6 8 7 GND VEE TRUTH TABLE ’HC4053, CD74HCT4053 INPUT STATES ENABLE S0 S1 S2 “ON” CHANNELS L L L L C0, B0, A0 L H L L C0, B0, A1 L L H L C0, B1, A0 L H H L C0, B1, A1 L L L H C1, B0, A0 L H L H C1, B0, A1 L L H H C1, B1, A0 L H H H C1, B1, A1 H X X X None X = Don’t care 5 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Absolute Maximum Ratings Thermal Information (Note 2) Package Thermal Impedance, θJA (see Note 1): E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67oC/W M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73oC/W NS (SOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64oC/W PW (TSSOP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . 108oC/W Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC DC Supply Voltage, VCC - VEE . . . . . . . . . . . . . . . . . -0.5V to 10.5V DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7V DC Supply Voltage, VEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.5V to -7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA DC Switch Diode Current, IOK For VI < VEE -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . .±20mA DC Switch Current, (Note 2) For VI > VEE -0.5V or VI < VCC + 0.5V . . . . . . . . . . . . . . . . .±25mA DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .±50mA DC VEE Current, IEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20mA NOTE: 1. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions For maximum reliability, nominal operating conditions should be selected so that operation is always within the following ranges PARAMETER MIN MAX UNITS 2 6 V 4.5 5.5 V 2 10 V 0 -6 V DC Input Control Voltage, VI GND VCC V Analog Switch I/O Voltage, VIS VEE VCC V Operating Temperature, TA -55 125 oC 2V 0 1000 ns 4.5V 0 500 ns 6V 0 400 ns Supply Voltage Range (For TA = Full Package Temperature Range), VCC (Note 2) CD54/74HC Types CD54/74HCT Types Supply Voltage Range (For TA = Full Package Temperature Range), VCC - VEE CD54/74HC Types, CD54/74HCT Types (See Figure 1) Supply Voltage Range (For TA = Full Package Temperature Range), VEE (Note 3) CD54/74HC Types, CD54/74HCT Types (See Figure 2) Input Rise and Fall Times, tr, tf CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 2. All voltages referenced to GND unless otherwise specified.. 3. In certain applications, the external load resistor current may include both VCC and signal line components. To avoid drawing VCC current when switch current flows into the transmission gate inputs, the voltage drop across the bidirectional switch must not exceed 0.6V (calculated from rON values shown in Electrical Specifications table). No VCC current will flow through RL if the switch current flows into terminal 3 on the HC/HCT4051; terminals 3 and 13 on the HC/HCT4052; terminals 4, 14 and 15 on the HC/HCT4053. Recommended Operating Area as a Function of Supply Voltages 8 VCC - GND (V) VCC - GND (V) 8 6 HCT HC 4 2 0 0 2 4 6 8 10 6 HCT 2 0 12 VCC - VEE (V) HC 4 0 -2 -4 -6 -8 VEE - GND (V) FIGURE 1. FIGURE 2. 6 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 DC Electrical Specifications TEST CONDITIONS PARAMETER VIS (V) VI (V) AMBIENT TEMPERATURE, TA VEE (V) 25oC -40oC - 85oC -55oC - 125oC VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS 2 1.5 - - 1.5 - 1.5 - V 4.5 3.15 - - 3.15 - 3.15 0 V 6 4.2 - - 4.2 - 4.2 - V 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V 0 4.5 - 70 160 - 200 - 240 Ω 0 6 - 60 140 - 175 - 210 Ω -4.5 4.5 - 40 120 - 150 - 180 Ω 0 4.5 - 90 180 - 225 - 270 Ω 0 6 - 80 160 - 200 - 240 Ω -4.5 4.5 - 45 130 - 162 - 195 Ω 0 4.5 - 10 - - - - - Ω 0 6 - 8.5 - - - - - Ω -4.5 4.5 - 5 - - - - - Ω 0 6 - - ±0.1 - ±1 - ±1 µA -5 5 - - ±0.1 - ±1 - ±1 µA 0 6 - - ±0.1 - ±1 - ±1 µA -5 5 - - ±0.2 - ±2 - ±2 µA 0 6 - - ±0.2 - ±2 - ±2 µA -5 5 - - ±0.4 - ±4 - ±4 µA VCC or GND 0 6 - - ±0.1 - ±1 - ±1 µA VCC or GND 0 6 - - 8 - 80 - 160 µA -5 5 - - 16 - 160 - 320 µA HC TYPES High Level Input Voltage, VIH Low Level Input Voltage, VIL On Resistance, rON IO = 1mA, (Figure 11) VCC or VEE VIL or VIH VCC to VEE Maximum On Resistance Between any Two Channels, ∆rON Switch On/Off Leakage Current, IIZ 1 and 2 Channels 4053 4 Channels 4052 8 Channels For Switch Off: When VIS = VCC, VOS = VEE; When VIS = VEE, VOS = VCC For Switch On: All Applicable Combinations of VIS and VOS Voltage Levels VIL or VIH 4051 Control Input Leakage Current, IIL Quiescent Device Current, ICC IO = 0 When VIS = VEE, VOS = VCC When VIS = VCC, VOS = VEE 7 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 DC Electrical Specifications (Continued) TEST CONDITIONS VIS (V) PARAMETER VI (V) AMBIENT TEMPERATURE, TA VEE (V) VCC (V) 25oC -40oC - 85oC -55oC - 125oC MIN TYP MAX MIN MAX MIN MAX UNITS HCT TYPES High Level Input Voltage, VIH 4.5 to 5.5 2 - - 2 - 2 - V Low Level Input Voltage, VIL 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V 0 4.5 - 70 160 - 200 - 240 Ω - - - - - - - - - Ω -4.5 4.5 - 40 120 - 150 - 180 Ω 0 4.5 - 90 180 - 225 - 270 Ω - - - - - - - - - Ω -4.5 4.5 - 45 130 - 162 - 195 Ω 0 4.5 - 10 - - - - - Ω - - - - - - - - - Ω -4.5 4.5 - 5 - - - - - Ω 0 6 - - ±0.1 - ±1 - ±1 µA -5 5 - - ±0.1 - ±1 - ±1 µA 0 6 - - ±0.1 - ±1 - ±1 µA -5 5 - - ±0.2 - ±2 - ±2 µA 0 6 - - ±0.2 - ±2 - ±2 µA -5 5 - - ±0.4 - ±4 - ±4 µA On Resistance, rON IO = 1mA, (Figure 15) VCC or VEE VIL or VIH VCC to VEE Maximum On Resistance Between any Two Channels, ∆rON Switch On/Off Leakage Current, IIZ 1 and 2 Channels 4053 4 Channels 4052 8 Channels For Switch Off: When VIS = VCC, VOS = VEE; When VIS = VEE, VOS = VCC For Switch On: All Applicable Combinations of VIS and VOS Voltage Levels VIL or VIH 4051 Control Input Leakage Current, IIL - (Note 4) - 5.5 - - ±0.1 - ±1 - ±1 µA Quiescent Device Current, ICC IO = 0 When VIS = VEE, VOS = VCC VCC or GND 0 5.5 - - 8 - 80 - 160 µA -4.5 5.5 - - 16 - 160 - 320 µA 4.5 to 5.5 - 100 360 - 450 - 490 µA Additional Quiescent Device Current Per Input Pin: 1 Unit Load When VIS = VCC, VOS = VEE ∆ICC (Note 5) VCC 2.1 NOTES: 4. Any voltage between VCC and GND. 5. For dual supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table INPUT UNIT LOADS (NOTE) 4051, 4053 All 0.5 4052 All 0.4 TYPE NOTE: Unit load is ∆ICC limit specified in DC Specifications table, e.g., 360mA max. at 25oC. 8 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Switching Specifications VCC = 5V, TA = 25oC, Input tr, tr = 6ns TYPICAL 4051 4052 4053 CL (pF) HC HCT HC HCT HC HCT UNITS Switch IN to OUT, tPHL, tPLH 15 4 4 4 4 4 4 ns Switch Turn-Off (S or E), tPHZ, tPLZ 15 19 19 21 21 18 18 ns Switch Turn-On (S or E), tPZH, tPZL 15 19 23 27 29 18 20 ns - 50 52 74 76 38 42 pF PARAMETER Propagation Delay Power Dissipation Capacitance, CPD (Note 6) NOTE: 6. CPD is used to determine the dynamic power consumption, per package. PD = CPD VCC2 fI + ∑ (CL + CS) VCC2 fO fO = output frequency fI = input frequency CL = output load capacitance CS = switch capacitance VCC = supply voltage Switching Specifications CL = 50pF, Input tr, tr = 6ns AMBIENT TEMPERATURE, TA 25oC -40oC - 85oC HC PARAMETER Propagation Delay, Switch In to Out, tPLH, tPHL Maximum Switch Turn “Off” Delay from S or E to Switch Output tPHZ, tPLZ 4051 4052 4053 HCT HC -55oC - 125oC HCT HC HCT VEE (V) VCC (V) MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN 0 2 - 60 - - - 75 - - - 90 - - ns 0 4.5 - 12 - 12 - 15 - 15 - 18 - 18 ns 0 6 - 10 - - - 13 - - - 15 - - ns -4.5 4.5 - 8 - 8 - 10 - 10 - 12 - 12 ns 0 2 - 225 - - - 280 - - - 340 - - ns 0 4.5 - 45 - 45 - 56 - 56 - 68 - 68 ns 0 6 - 38 - - - 48 - - - 57 - - ns -4.5 4.5 - 32 - 32 - 40 - 40 - 48 - 48 ns 0 2 - 250 - - - 315 - - - 375 - - ns 0 4.5 - 50 - 50 - 63 - 63 - 75 - 75 ns 0 6 - 43 - - - 54 - - - 65 - - ns -4.5 4.5 - 38 - 38 - 48 - 48 - 57 - 57 ns 0 2 - 210 - - - 265 - - - 315 - - ns 0 4.5 - 42 - 44 - 53 - 55 - 63 - 66 ns 0 6 - 36 - - - 45 - - - 54 - - ns -4.5 4.5 - 29 - 31 - 36 - 39 - 44 - 47 ns 9 MAX UNITS ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Switching Specifications CL = 50pF, Input tr, tr = 6ns (Continued) AMBIENT TEMPERATURE, TA 25oC -40oC - 85oC HC PARAMETER Maximum Switch Turn “On” Delay from S or E to Switch Output tPZL, tPZH 4051 4052 4053 Input (Control) Capacitance, CI HCT HC -55oC - 125oC HCT HC HCT VEE (V) VCC (V) MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN 0 2 - 225 - - - 280 - - - 340 - - ns 0 4.5 - 45 - 55 - 56 - 69 - 68 - 83 ns 0 6 - 38 - - - 48 - - - 57 - - ns -4.5 4.5 - 32 - 39 - 40 - 49 - 48 - 59 ns 0 2 - 325 - - - 405 - - - 490 - - ns 0 4.5 - 65 - 70 - 81 - 68 - 98 - 105 ns 0 6 - 55 - - - 69 - - - 83 - - ns -4.5 4.5 - 46 - 48 - 58 - 60 - 69 - 72 ns 0 2 - 220 - - - 275 - - - 330 - - ns 0 4.5 - 44 - 48 - 55 - 60 - 66 - 72 ns 0 6 - 37 - - - 47 - - - 56 - - ns -4.5 4.5 - 31 - 34 - 39 - 43 - 47 - 51 ns - - - 10 - 10 - 10 - 10 - 10 - 10 pF Analog Channel Specifications MAX UNITS Typical Values at TA = 25oC PARAMETER TEST CONDITIONS Switch Input Capacitance, CI Common Output Capacitance, CCOM Minimum Switch Frequency Response at -3dB, fMAX (Figures 12, 14, 16) See Figure 3 (Notes 7, 8) HC/HCT TYPES VEE (V) VCC (V) HC/ HCT UNITS All - - 5 pF 4051 - - 25 pF 4052 - - 12 pF 4053 - - 8 pF 145 MHz 165 MHz 4053 200 MHz 4051 180 MHz 185 MHz 200 MHz 4051 4052 4052 4053 10 -2.25 -4.5 2.25 4.5 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Analog Channel Specifications Typical Values at TA = 25oC PARAMETER Crosstalk Between any Two Switches (Note 10) TEST CONDITIONS See Figure 4 (Notes 8, 9) HC/ HCT UNITS N/A dB (TBE) dB 4053 (TBE) dB 4051 N/A dB (TBE) dB (TBE) dB HC/HCT TYPES VEE (V) VCC (V) 4051 4052 4052 -2.25 -4.5 2.25 4.5 4053 Sinewave Distortion E or S to Switch Feedthrough Noise See Figure 5 See Figure 6 (Notes 8, 9) All -2.25 2.25 0.035 % All -4.5 4.5 0.018 % 4051 4052 mV -2.25 2.25 (TBE) 4053 mV 4051 mV 4052 -4.5 4.5 (TBE) 4053 Switch “OFF” Signal Feedthrough (Figures 13, 15, 17) See Figure 7 (Notes 8, 9) -73 dB -65 dB 4053 -64 dB 4051 -75 dB -67 dB -66 dB 4052 4053 7. Adjust input voltage to obtain 0dBm at VOS for fIN = 1MHz. 8. VIS is centered at (VCC - VEE)/2. 9. Adjust input for 0dBm. 10. Not applicable for HC/HCT4051. 11 mV mV 4051 4052 NOTES: mV -2.25 -4.5 2.25 4.5 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Test Circuits and Waveforms VCC VIS R 0.1µF INPUT SWITCH ON VOS1 C R fIS = 1MHz SINEWAVE R = 50Ω C = 10pF VCC VOS SWITCH ON VIS 0.1µF VCC /2 VCC 50Ω dB METER 10pF R VCC /2 SWITCH OFF VCC /2 VOS2 R dB METER C VCC /2 FIGURE 3. FREQUENCY RESPONSE TEST CIRCUIT FIGURE 4. CROSSTALK BETWEEN TWO SWITCHES TEST CIRCUIT E VCC VCC VI = VIH SINEWAVE VIS 10µF VIS SWITCH ON fIS = 1kHz TO 10kHz SWITCH ALTERNATING ON AND OFF tr, tf ≤ 6ns fCONT = 1MHz 50% DUTY CYCLE 600Ω VOS 10kΩ 50pF VCC /2 DISTORTION METER VCC /2 FIGURE 5. SINEWAVE DISTORTION TEST CIRCUIT fIS ≥ 1MHz SINEWAVE R = 50Ω C = 10pF VC = VIL VOS SWITCH OFF VIS VOS 600Ω 50pF SCOPE VCC /2 FIGURE 6. CONTROL TO SWITCH FEEDTHROUGH NOISE TEST CIRCUIT VCC 0.1µF VP-P VOS R R VCC /2 VCC /2 C dB METER FIGURE 7. SWITCH OFF SIGNAL FEEDTHROUGH 12 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Test Circuits and Waveforms (Continued) VCC tr = 6ns tf = 6ns 90% 50% 10% SWITCH INPUT tPLH tPHL VEE 90% 50% 10% SWITCH OUTPUT FIGURE 8A. 6ns 6ns 6ns 90% E OR Sn 50% E OR Sn 10% tPLZ tPLZ OUTPUT LOW TO OFF 10% tPZH SWITCH ON SWITCH OFF 50% 10% tPZH 90% OUTPUT HIGH TO OFF 50% 50% SWITCH ON SWITCH ON GND tPZL tPHZ 90% OUTPUT HIGH TO OFF 3V 0.3 GND 50% tPHZ 6ns 2.7 1.3 tPZL OUTPUT LOW TO OFF tf tr VCC FIGURE 8B. HC TYPES SWITCH OFF SWITCH ON FIGURE 8C. HCT TYPES FIGURE 8. SWITCH PROPAGATION DELAY, TURN-ON, TURN-OFF TIMES VEE FOR tPLZ AND tPZL VCC FOR tPHZ AND tPZH RL = 1kΩ VCC FOR tPLZ AND tPZL CL 50pF VEE FOR tPHZ AND tPZH TG IN OUT IN OUT TG 50pF FIGURE 9. SWITCH ON/OFF PROPAGATION DELAY TEST CIRCUIT FIGURE 10. SWITCH IN TO SWITCH OUT PROPAGATION DELAY TEST CIRCUIT 13 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Typical Performance Curves 120 ON RESISTANCE (Ω) 100 80 VCC - VEE = 4.5V 60 VCC - VEE = 6V 40 VCC - VEE = 9V 20 1 2 3 4 5 6 INPUT SIGNAL VOLTAGE (V) 7 8 9 FIGURE 11. TYPICAL ON RESISTANCE vs INPUT SIGNAL VOLTAGE 0 0 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50Ω PIN 12 TO 3 -2 -20 VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50Ω PIN 12 TO 3 -40 -4 -6 dB dB VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50Ω PIN 12 TO 3 -60 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50Ω PIN 12 TO 3 -80 -8 -10 10K 100K 1M FREQUENCY (Hz) 10M -100 10K 100M FIGURE 12. CHANNEL ON BANDWIDTH (HC/HCT4051) 100K 1M FREQUENCY (Hz) 10M 100M FIGURE 13. CHANNEL OFF FEEDTHROUGH (HC/HCT4051) 0 0 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50Ω PIN 4 TO 3 -2 -4 -40 dB dB VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50Ω PIN 4 TO 3 -6 VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50Ω PIN 4 TO 3 -20 -60 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50Ω PIN 4 TO 3 -80 -8 -10 10K 100K 1M FREQUENCY (Hz) 10M -100 10K 100M FIGURE 14. CHANNEL ON BANDWIDTH (HC/HCT4052) 100K 1M FREQUENCY (Hz) 10M 100M FIGURE 15. CHANNEL OFF FEEDTHROUGH (HC/HCT4052) 14 ’HC4051, ’HCT4051, ’HC4052, CD74HCT4052, ’HC4053, CD74HCT4053 Typical Performance Curves (Continued) 0 0 VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50Ω PIN 5 TO 4 -20 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50Ω PIN 5 TO 4 -2 -40 dB dB -1 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50Ω PIN 5 TO 4 -60 VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50Ω PIN 5 TO 4 -3 -4 10K 100K 1M FREQUENCY (Hz) 10M -80 -100 10K 100M FIGURE 16. CHANNEL ON BANDWIDTH (HC/HCT4053) 100K 1M FREQUENCY (Hz) 10M 100M FIGURE 17. CHANNEL OFF FEEDTHROUGH (HC/HCT4053) 15 PACKAGE OPTION ADDENDUM www.ti.com 5-Dec-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 5962-8775401EA ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC 5962-8855601EA ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC 5962-9065401MEA ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC CD54HC4051F ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC CD54HC4051F3A ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC Lead/Ball Finish MSL Peak Temp (3) CD54HC4052F ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC CD54HC4052F3A ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC CD54HC4053F ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC CD54HC4053F3A ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC CD54HCT4051F3A ACTIVE CDIP J 16 1 TBD Call TI Level-NC-NC-NC CD74HC4051E ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HC4051EE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HC4051M ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051M96 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051M96E4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051ME4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051MT ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051MTE4 ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051NSR ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051NSRE4 ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051PWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051PWRE4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051PWT ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4051PWTE4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4052E ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HC4052EE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HC4052M ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4052M96 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 5-Dec-2005 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty CD74HC4052M96E4 ACTIVE SOIC D 16 CD74HC4052ME4 ACTIVE SOIC D 16 40 CD74HC4052MT ACTIVE SOIC D 16 CD74HC4052MTE4 ACTIVE SOIC D CD74HC4052NSR ACTIVE SO CD74HC4052NSRE4 ACTIVE CD74HC4052PW 2500 Green (RoHS & no Sb/Br) Lead/Ball Finish MSL Peak Temp (3) CU NIPDAU Level-1-260C-UNLIM Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4052PWE4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4052PWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4052PWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4052PWRE4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4052PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4052PWT ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4052PWTE4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4052SM OBSOLETE SSOP DB 16 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053E ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HC4053EE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HC4053M ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053M96 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053M96E4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053ME4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053MT ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053MTE4 ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053NSR ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053NSRG4 ACTIVE SO NS 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053PW ACTIVE TSSOP PW 16 CU NIPDAU Level-1-260C-UNLIM 90 Addendum-Page 2 Green (RoHS & no Sb/Br) PACKAGE OPTION ADDENDUM www.ti.com 5-Dec-2005 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty CD74HC4053PWE4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053PWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053PWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053PWRE4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053PWT ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053PWTE4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4053PWTG4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4051E ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HCT4051EE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HCT4051M ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4051M96 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4051M96E4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4051M96G4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4051ME4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4051MG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4051MT ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4051MTE4 ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4052E ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HCT4052EE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HCT4052M ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4052M96 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4052M96E4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4052M96G4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4052ME4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4052MG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 3 Lead/Ball Finish MSL Peak Temp (3) PACKAGE OPTION ADDENDUM www.ti.com 5-Dec-2005 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty CD74HCT4052MT ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4052MTE4 ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053E ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HCT4053EE4 ACTIVE PDIP N 16 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HCT4053M ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053M96 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053M96E4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053ME4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053MT ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053MTE4 ACTIVE SOIC D 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053PWR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053PWRE4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053PWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053PWT ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053PWTE4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HCT4053PWTG4 ACTIVE TSSOP PW 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is Addendum-Page 4 PACKAGE OPTION ADDENDUM www.ti.com 5-Dec-2005 provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 5 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated