AD ADG1404 1.5 on resistance Datasheet

1.5 Ω On Resistance,
±15 V/12 V/±5 V, 4:1, iCMOS Multiplexer
ADG1404
FEATURES
FUNCTIONAL BLOCK DIAGRAM
1.5 Ω on resistance
0.3 Ω on-resistance flatness
0.1 Ω on-resistance match between channels
Up to 400 mA continuous current
Fully specified at +12 V, ±15 V, and ±5 V
No VL supply required
3 V logic-compatible inputs
Rail-to-rail operation
14-lead TSSOP and 4 mm × 4 mm, 16-lead LFCSP
ADG1404
S1
S2
D
S3
S4
A0
A1
EN
06816-001
1 OF 4
DECODER
Figure 1.
APPLICATIONS
Automatic test equipment
Data acquisition systems
Battery-powered systems
Sample-and-hold systems
Audio signal routing
Communication systems
Relay replacement
GENERAL DESCRIPTION
The ADG1404 is a complementary metal-oxide semiconductor
(CMOS) analog multiplexer, comprising four single channels
designed on an iCMOS® process. iCMOS (industrial CMOS) is
a modular manufacturing process that combines high voltage
CMOS and bipolar technologies. It enables the development of
a wide range of high performance analog ICs capable of 33 V
operation in a footprint that no previous generation of high
voltage parts has been able to achieve. Unlike analog ICs using
conventional CMOS processes, iCMOS components can
tolerate high supply voltages while providing increased
performance, dramatically lower power consumption, and
reduced package size.
The on-resistance profile is very flat over the full analog input
range, ensuring excellent linearity and low distortion when
switching audio signals.
The ADG1404 switches one of four inputs to a common output,
D, as determined by the 3-bit binary address lines, A0, A1, and
EN. Logic 0 on the EN pin disables the device. Each switch
conducts equally well in both directions when on and has an
input signal range that extends to the supplies. In the off condition, signal levels up to the supplies are blocked. All switches
exhibit break-before-make switching action. Inherent in the
design is low charge injection for minimum transients when
switching the digital inputs.
PRODUCT HIGHLIGHTS
1.
2.
3.
4.
2.6 Ω maximum on resistance over temperature.
Minimum distortion.
Ultralow power dissipation: <0.03 μW.
14-lead TSSOP and 16-lead, 4 mm × 4 mm LFCSP package.
iCMOS construction ensures ultralow power dissipation,
making the parts ideally suited for portable and batterypowered instruments.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2008–2009 Analog Devices, Inc. All rights reserved.
ADG1404
TABLE OF CONTENTS
Features .............................................................................................. 1
Continuous Current, S or D.........................................................6
Applications ....................................................................................... 1
Absolute Maximum Ratings ............................................................7
Functional Block Diagram .............................................................. 1
ESD Caution...................................................................................7
General Description ......................................................................... 1
Pin Configurations and Function Descriptions ............................8
Product Highlights ........................................................................... 1
Truth Table .....................................................................................8
Revision History ............................................................................... 2
Typical Performance Characteristics ..............................................9
Specifications..................................................................................... 3
Terminology .................................................................................... 12
15 V Dual Supply .......................................................................... 3
Test Circuits ..................................................................................... 13
12 V Single Supply ........................................................................ 4
Outline Dimensions ....................................................................... 16
5 V Dual Supply ............................................................................ 5
Ordering Guide .......................................................................... 16
REVISION HISTORY
3/09—Rev. 0 to Rev. A
Changes to Power Requirements, IDD, Digital Inputs = 5 V
Parameter, Table 1............................................................................. 3
Changes to Power Requirements, IDD, Digital Inputs = 5 V
Parameter, Table 2............................................................................. 4
Updated Outline Dimensions ....................................................... 16
7/08—Revision 0: Initial Version
Rev. A | Page 2 of 16
ADG1404
SPECIFICATIONS
15 V DUAL SUPPLY
VDD = 15 V ± 10%, VSS = −15 V± 10%, GND = 0 V, unless otherwise noted.
Table 1.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On-Resistance Match
Between Channels (ΔRON)
On-Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage, IS (Off)
25°C
−40°C to +85°C
−40°C to +125°C
Unit
VDD to VSS
V
Ω typ
1.5
1.8
0.1
2.3
2.6
Ω max
Ω typ
0.18
0.3
0.36
0.19
0.21
0.4
0.45
Ω max
Ω typ
Ω max
nA typ
±2
±12.5
Drain Off Leakage, ID (Off)
nA max
nA typ
±4
±30
Channel On Leakage, ID, IS (On)
±0.55
±0.1
nA max
nA typ
±2
±4
±30
nA max
2.0
0.8
V min
V max
μA typ
μA max
pF typ
0.005
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION
tON (EN)
tOFF (EN)
Break-Before-Make Time Delay, tBBM
VS = ±10 V, IS = −10 mA; see Figure 22
VDD = +13.5 V, VSS = −13.5 V
VS = ±10 V, IS = −10 mA
VS = ±10 V, IS = −10 mA
VDD = +16.5 V, VSS = −16.5 V
±0.03
±0.55
±0.04
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINLor INH
Test Conditions/Comments
3.5
VS = ±10 V, Vs = ∓10 V; see Figure 23
VS = ±10 V, Vs = ∓10 V; see Figure 23
VS = VD = ±10 V; see Figure 24
VIN = VGND or VDD
150
180
220
250
ns typ
ns max
100
120
145
165
ns typ
ns max
110
135
165
185
ns typ
ns max
10
ns typ
ns min
RL = 300 Ω, CL = 35 pF
VS = +10 V; see Figure 29
RL = 300 Ω, CL = 35 pF
VS = +10 V; see Figure 31
RL = 300 Ω, CL = 35 pF
VS = +10 V; see Figure 31
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 10 V; see Figure 30
VS = 0 V, RS = 0 Ω, CL = 1 nF; see Figure 32
35
Charge Injection
−20
pC typ
Off Isolation
70
dB typ
RL = 50 Ω, CL = 5 pF, f = 100 kHz; see Figure 25
Channel-to-Channel Crosstalk
82
dB typ
Total Harmonic Distortion + Noise
0.011
% typ
RL = 50 Ω, CL = 5 pF, f = 100 kHz; see Figure 27
RL = 110 Ω, 10 V p-p, f = 20 Hz to 20 kHz; see
−3 dB Bandwidth
55
MHz typ
RL = 50 Ω, CL = 5 pF; see Figure 26
Insertion Loss
−0.17
dB typ
23
90
170
pF typ
pF typ
pF typ
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 26
f = 1 MHz, VS = 0 V
f = 1 MHz, VS = 0 V
f = 1 MHz, VS = 0 V
VDD = +16.5 V, VSS = −16.5 V
Digital inputs = 0 V or VDD
Figure 28
CS (Off)
CD (Off)
CD, CS (On)
POWER REQUIREMENTS
IDD
0.001
1
IDD
170
285
ISS
0.001
VDD/VSS
1
1
±4.5/±16.5
Guaranteed by design, not subject to production test.
Rev. A | Page 3 of 16
μA typ
μA max
μA typ
μA max
μA typ
μA max
V min/max
Digital inputs = 5 V
Digital inputs = 0 V or VDD
GND = 0 V
ADG1404
12 V SINGLE SUPPLY
VDD = 12 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 2.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On-Resistance Match
Between Channels (ΔRON)
On-Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage, IS (Off)
Drain Off Leakage, ID (Off)
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
25°C
2.8
3.5
0.13
0.21
0.6
1.1
±0.02
±0.55
±0.03
±0.55
±0.1
±1.5
−40°C to +85°C
−40°C to +125°C
Unit
Test Conditions/Comments
0 V to VDD
V
Ω typ
Ω max
Ω typ
VS = 0 V to 10 V, IS = −10 mA; see Figure 22
VDD = 10.8 V, VSS = 0 V
VS = 0 V to 10 V, IS = −10 mA
4.3
4.8
0.23
0.25
1.2
1.3
±2
±12.5
±4
±30
±4
±30
2.0
0.8
0.001
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION
tON (EN)
tOFF (EN)
Break-Before-Make Time Delay, tBBM
3.5
230
300
180
240
115
160
100
375
430
295
335
190
220
10
Charge Injection
Off Isolation
Channel-to-Channel Crosstalk
−3 dB Bandwidth
Insertion Loss
CS (Off)
CD (Off)
CD, CS (On)
POWER REQUIREMENTS
IDD
30
80
82
35
−0.3
39
150
217
0.001
1
IDD
170
VDD
1
285
5/16.5
Guaranteed by design, not subject to production test.
Rev. A | Page 4 of 16
Ω max
Ω typ
Ω max
nA typ
nA max
nA typ
nA max
nA typ
nA max
V min
V max
μA typ
μA max
pF typ
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
dB typ
MHz typ
dB typ
pF typ
pF typ
pF typ
μA typ
μA max
μA typ
μA max
V min/max
VS = 0V to 10 V, IS = −10 mA
VDD = 13.2 V, VSS = 0 V
VS = 1 V/10 V, VD = 10 V/1 V; see Figure 23
VS = 1 V/10 V, VD = 10 V/1 V; see Figure 23
VS = VD = 1 V or 10 V; see Figure 24
VIN = VGND or VDD
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 29
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 31
RL = 300 Ω, CL = 35 pF
VS = 8 V; see Figure 31
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 8 V; see Figure 30
VS = 6 V, RS = 0 Ω, CL = 1 nF; see Figure 32
RL = 50 Ω, CL = 5 pF, f = 100 kHz; see Figure 25
RL = 50 Ω, CL = 5 pF, f = 100 kHz; see Figure 27
RL = 50 Ω, CL = 5 pF; see Figure 26
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 26
f = 1 MHz, VS = 6 V
f = 1 MHz, VS = 6 V
f = 1 MHz, VS = 6 V
VDD = 13.2 V
Digital inputs = 0 V or VDD
Digital inputs = 5 V
GND = 0 V, VSS = 0 V
ADG1404
5 V DUAL SUPPLY
VDD = 5 V ± 10%, VSS = −5 V ± 10%, GND = 0 V, unless otherwise noted.
Table 3.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On-Resistance Match
Between Channels (∆RON)
On-Resistance Flatness (RFLAT(ON))
LEAKAGE CURRENTS
Source Off Leakage, IS (Off)
Drain Off Leakage, ID (Off)
Channel On Leakage, ID, IS (On)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IINL or IINH
25°C
3.3
4
0.13
0.22
0.9
1.1
−40°C to +85°C
−40°C to +125°C
Unit
Test Conditions/Comments
VDD to VSS
V
Ω typ
Ω max
Ω typ
VS = ±4.5 V, IS = −10 mA; see Figure 22
VDD = +4.5 V, VSS = −4.5 V
VS = ±4.5 V, IS = −10 mA
4.9
5.4
0.23
0.25
1.24
1.31
VS = ±4.5 V, VD = ∓4.5 V; see Figure 23
VS = ±4.5 V, VD = ∓4.5 V; see Figure 23
±0.2
±0.02
±1
±12.5
nA max
nA typ
±0.25
±0.05
±0.25
±1.2
±15
VS = VD = ±4.5 V; see Figure 24
±1.5
±20
nA max
nA typ
nA max
V min
V max
μA typ
μA max
pF typ
VIN = VGND or VDD
2.0
0.8
0.001
35
Break-Before-Make Time Delay, tBBM
Charge Injection
Off Isolation
30
80
ns typ
ns max
ns typ
ns max
ns typ
ns max
ns typ
ns min
pC typ
dB typ
Channel-to-Channel Crosstalk
82
dB typ
−3 dB Bandwidth
Insertion Loss
Total Harmonic Distortion + Noise
40
0.27
0.03
MHz typ
dB typ
% typ
33
128
210
pF typ
pF typ
pF typ
tOFF (EN)
560
615
430
480
365
400
50
CS (Off)
CD (Off)
CD, CS (On)
POWER REQUIREMENTS
IDD
ISS
0.001
RL = 300 Ω, CL = 35 pF
VS = 3 V; Figure 29
RL = 300 Ω, CL = 35 pF
VS = 3 V; Figure 31
RL = 300 Ω, CL = 35 pF
VS = 3 V; Figure 31
RL = 300 Ω, CL = 35 pF
VS1 = VS2 = 3 V; see Figure 30
VS = 0 V, RS = 0 Ω, CL = 1 nF; see Figure 32
RL = 50 Ω, CL = 5 pF, f = 100 kHz;
see Figure 25
RL = 50 Ω, CL = 5 pF, f = 100 kHz;
see Figure 27
RL = 50 Ω, CL = 5 pF; see Figure 26
RL = 50 Ω, CL = 5 pF, f = 1 MHz; see Figure 26
RL = 110 Ω, 2.5 V p-p, f = 20 Hz to 20 kHz;
see Figure 28
VS = 0 V, f = 1 MHz
VS = 0 V, f = 1 MHz
VS = 0 V, f = 1 MHz
VDD = 5.5 V, VSS = −5.5 V
Digital inputs = 0 V, 5 V, or VDD
1
μA typ
μA max
μA typ
μA max
Digital inputs = 0 V or VDD
1
±4.5/±16.5
V min/max
GND = 0 V
0.001
VDD/VSS
1
nA typ
340
470
260
355
220
315
100
tON (EN)
VS = ±4.5 V, IS = −10 mA
VDD = +5.5 V, VSS = −5.5 V
±0.02
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS1
Transition Time, tTRANSITION
Ω max
Ω typ
Ω max
Guaranteed by design, not subject to production test.
Rev. A | Page 5 of 16
ADG1404
CONTINUOUS CURRENT, S OR D
Table 4.
Parameter
CONTINUOUS CURRENT, S or D1
15 V Dual Supply
ADG1404 TSSOP
ADG1404 LFCSP
12 V Single Supply
ADG1404 TSSOP
ADG1404 LFCSP
5 V Dual Supply
ADG1404 TSSOP
ADG1404 LFCSP
1
25°C
85°C
125°C
Unit
350
450
220
300
100
140
mA max
mA max
300
400
220
300
100
140
mA max
mA max
300
400
220
300
100
140
mA max
mA max
Test Conditions/Comments
VDD = +13.5 V, VSS = −13.5 V
VDD = 10.8 V, VSS = 0 V
VDD = +4.5 V, VSS = −4.5 V
Guaranteed by design, not subject to production test.
Rev. A | Page 6 of 16
ADG1404
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 5.
Parameter
VDD to VSS
VDD to GND
VSS to GND
Analog Inputs1
Digital Inputs
Peak Current, S or D
Continuous Current, S or D2
Operating Temperature Range
Automotive (Y Version)
Storage Temperature Range
Junction Temperature
14-Lead TSSOP, θJA Thermal
Impedance (4-layer board)
16-Lead LFCSP, θJA Thermal
Impedance
Reflow Soldering Peak
Temperature, Pb free
1
2
Rating
35 V
−0.3 V to +25 V
+0.3 V to −25 V
VSS − 0.3 V to VDD + 0.3 V or 30
mA, whichever occurs first
GND − 0.3 V to VDD + 0.3 V or
30 mA, whichever occurs first
600 mA (pulsed at 1 ms,
10% duty cycle maximum)
Data + 15%
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Only one absolute maximum rating may be applied at any
one time.
ESD CAUTION
−40°C to +125°C
−65°C to +150°C
150°C
112°C/W
30.4°C/W
260(+0/−5)°C
Overvoltages at IN, S, and D are clamped by internal diodes. Current should
be limited to the maximum ratings given.
See data given in Table 4.
Rev. A | Page 7 of 16
ADG1404
12
VDD
VSS 3
ADG1404
NC 2
S1 3
TOP VIEW
11 S3
(Not to Scale)
10 S4
D 6
9
NC
NC 7
8
NC
NC = NO CONNECT
14 A1
13 NC
12 GND
ADG1404
11 VDD
TOP VIEW
(Not to Scale)
9 S4
NC 5
S2 5
S2 4
10 S3
NOTES
1. EXPOSED PAD TIED TO SUBSTRATE, VSS.
2. NC = NO CONNECT.
06816-002
S1 4
PIN 1
INDICATOR
VSS 1
06816-003
GND
NC 8
A1
NC 7
14
13
D 6
A0 1
EN 2
15 A0
16 EN
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Figure 3. LFCSP Pin Configuration
Figure 2. TSSOP Pin Configuration
Table 6. Pin Function Descriptions
TSSOP
1
2
3
4
5
6
7 to 9
10
11
12
13
14
Pin No.
LFCSP
15
16
1
3
4
6
2, 5, 7, 8, 13
9
10
11
12
14
Mnemonic
A0
EN
VSS
S1
S2
D
NC
S4
S3
VDD
GND
A1
Description
Logic Control Input.
Active High Digital Input. When this pin is low, the device is disabled and all switches are off.
When this pin is high, the Ax logic inputs determine the on switches.
Most Negative Power Supply Potential.
Source Terminal. Can be an input or an output.
Source Terminal. Can be an input or an output.
Drain Terminal. Can be an input or an output.
No Connection.
Source Terminal. Can be an input or an output.
Source Terminal. Can be an input or an output.
Most Positive Power Supply Potential.
Ground (0 V) Reference.
Logic Control Input.
TRUTH TABLE
Table 7.
EN
0
1
1
1
1
A1
X
0
0
1
1
A0
X
0
1
0
1
S1
Off
On
Off
Off
Off
Rev. A | Page 8 of 16
S2
Off
Off
On
Off
Off
S3
Off
Off
Off
On
Off
S4
Off
Off
Off
Off
On
ADG1404
TYPICAL PERFORMANCE CHARACTERISTICS
2.5
3.0
VDD = +10V,
VSS = –10V
2.5
1.5
VDD = +13.5V,
VSS = –13.5V
1.0
VDD = +16.5V,
VSS = –16.5V
VDD = +15V,
VSS = –15V
0.5
TA = +85°C
1.5
TA = +25°C
TA = –40°C
1.0
0.5
TA = 25°C
IS = –10mA
–12.5
–8.5
–4.5
–0.5
3.5
11.5
7.5
15.5
VS OR VD (V)
Figure 4. On Resistance as a Function of VD (VS), Dual Supply
4.0
5
10
15
4.5
ON RESISTANCE (Ω)
4.0
VDD = +7V,
VSS = –7V
VDD = +5.5V,
VSS = –5.5V
1.5
0
5.0
2.5
2.0
–5
Figure 7. On Resistance as a Function of VD (VS) for Different Temperatures,
15 V Dual Supply
VDD = +5V,
VSS = –5V
3.0
–10
VS OR VD (V)
VDD = +4.5V,
VSS = –4.5V
3.5
VDD = +15V
VSS = –15V
IS = –10mA
0
–15
06816-004
0
–16.5
ON RESISTANCE (Ω)
TA = +125°C
2.0
06816-007
VDD = +12V,
VSS = –12V
ON RESISTANCE (Ω)
ON RESISTANCE (Ω)
2.0
TA = +125°C
3.5
TA = +85°C
3.0
TA = +25°C
2.5
2.0
TA = –40°C
1.5
1.0
1.0
–6
–5
–4
–3
–2
–1
0
1
2
3
4
5
6
7
VS OR VD (V)
0
–5
Figure 5. On Resistance as a Function of VD (VS), Dual Supply
–4
–3
–2
–1
0
1
2
3
4
5
VS OR VD (V)
Figure 8. On Resistance as a Function of VD (VS) for Different Temperatures,
5 V Dual Supply
7
4.5
VDD = 5V,
VSS = 0V
4.0
VDD = 10.8V,
VSS = 0V
VDD = 8V,
VSS = 0V
4
ON RESISTANCE (Ω)
5
VDD = 12V,
VSS = 0V
3
2
VDD = 13.2V,
VSS = 0V
TA = 25°C
IS = –10mA
0
0
2
4
6
8
10
12
14
VS OR VD (V)
Figure 6. On Resistance as a Function of VD (VS), Single Supply
TA = +125°C
3.0
TA = +85°C
2.5
TA = +25°C
2.0
TA = –40°C
1.5
1.0
VDD = 15V,
VSS = 0V
VDD = 12V
VSS = 0V
IS = –10mA
0.5
0
06816-006
1
3.5
0
2
4
6
VS OR VD (V)
8
10
12
06815-109
6
ON RESISTANCE (Ω)
VDD = +5V
VSS = –5V
IS = –10mA
06815-108
0
–7
0.5
TA = 25°C
IS = –10mA
06816-005
0.5
Figure 9. On Resistance as a Function of VD (VS) for Different Temperatures,
Single Supply
Rev. A | Page 9 of 16
ADG1404
6
80
4
TA = 25°C
IDD PER LOGIC INPUT
70
2
60
IS (OFF) + –
ID (OFF) + –
IS (OFF) – +
ID (OFF) – +
ID, IS (ON) + +
ID, IS (ON) – –
–2
–4
–6
50
IDD (µA)
LEAKAGE (nA)
0
40
VDD = +15V
VSS = –15V
VDD = +12V
VSS = 0V
30
–8
20
–10
VDD = +15V
VSS = –15V
VBIAS = +10V/–10V
40
60
80
100
120
TEMPERATURE (°C)
0
0
2
4
LEAKAGE (nA)
2
1
0
–1
–2
0
20
40
60
80
100
120
TA = 25°C
VDD = +15V, VSS = –15V
200
VDD = +5V, VSS = –5V
0
VDD = +12V, VSS = 0V
–200
TEMPERATURE (°C)
–600
–15
06816-112
–4
8
0
350
2
300
VDD = +12V, VSS = 0V
250
200
150
0
VDD = +15V, VSS = –15V
100
VDD = 12V
VSS = 0V
VBIAS = 1V/10V
20
50
40
60
80
TEMPERATURE (°C)
100
120
06816-113
0
15
VDD = +5V, VSS = –5V
400
4
–4
10
450
6
–2
5
500
TIME (ns)
LEAKAGE (nA)
10
–5
Figure 14. Charge Injection vs. Source Voltage
IS (OFF) + –
ID (OFF) + –
IS (OFF) – +
ID (OFF) – +
ID, IS (ON) + +
ID, IS (ON) – –
12
–10
VS (V)
Figure 11. Leakage Currents as a Function of Temperature, 5 V Dual Supply
14
14
–400
VDD = +5V
VSS = –5V
VBIAS = +4.5V/–4.5V
–3
12
400
CHARGE INJECTION (pC)
3
10
Figure 13. IDD vs. Logic Level
600
IS (OFF) + –
ID (OFF) + –
IS (OFF) – +
ID (OFF) – +
ID, IS (ON) + +
ID, IS (ON) – –
8
LOGIC, Ax (V)
Figure 10. Leakage Currents as a Function of Temperature,15 V Dual Supply
4
6
06815-008
20
06816-012
0
VDD = +5V
VSS = –5V
Figure 12. Leakage Currents as a Function of Temperature, 12 V Single Supply
Rev. A | Page 10 of 16
0
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 15. Transition Times vs. Temperature
120
06816-013
–14
10
06816-111
–12
0.024
0.022
0.020
0.016
0.014
0.010
VS = 10V p-p
0.006
100k
1M
10M
100M
0.002
10
100
1k
10k
100k
FREQUENCY (Hz)
06816-017
0.004
Figure 16. Off Isolation vs. Frequency
0
VS = 15V p-p
0.012
0.008
FREQUENCY (Hz)
–10
VS = 20V p-p
VDD = +15V
VSS = –15V
TA = 25°C
0.018
THD + N (%)
0
–5 TA = 25°C
–10
–15
–20
–25
–30
–35
–40
–45
–50
–55
–60
–65
–70
–75
–80
–85
–90
–95
–100
1k
10k
06816-014
OFF ISOLATION (dB)
ADG1404
Figure 19. THD + N vs. Frequency at ±15 V
1
TA = 25°C
–20
VDD = +5V
VSS = –5V
TA = 25°C
VS = 10V p-p
0.1
–40
THD + N (%)
CROSSTALK (dB)
–30
–50
–60
–70
VS = 5V p-p
0.01
VS = 2.5V p-p
–80
–90
10k
100k
1M
10M
100M
FREQUENCY (Hz)
0.001
10
06816-015
–110
1k
10k
100k
Figure 20. THD + N vs. Frequency at ±5 V
0
0
–10
VDD = +15V
VSS = –15V
TA = 25°C
–20
–2
VDD = +15V
VSS = –15V
V p-p = 0.63V
TA = 25°C
ACPSRR (dB)
–30
–3
–4
–40
NO DECOUPLING
CAPACITORS
–50
–60
DECOUPLING
CAPACITORS
ON SUPPLIES
–70
–5
–80
–6
–90
10k
100k
1M
10M
FREQUENCY (Hz)
100M
Figure 18. On Response vs. Frequency
–100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 21. ACPSRR vs. Frequency
Rev. A | Page 11 of 16
10M
06815-017
–7
1k
06816-016
INSERTION LOSS (dB)
1k
FREQUENCY (Hz)
Figure 17. Crosstalk vs. Frequency
–1
100
06816-018
–100
ADG1404
TERMINOLOGY
IDD
The positive supply current.
CIN
The digital input capacitance.
ISS
The negative supply current.
tTRANSITION
The delay time between the 50% and 90% points of the digital
input and switch on condition when switching from one
address state to another.
VD (VS)
The analog voltage on Terminal D and Terminal S.
RON
The ohmic resistance between Terminal D and Terminal S.
RFLAT(ON)
Flatness that is defined as the difference between the maximum
and minimum value of on resistance measured over the
specified analog signal range.
tON (EN)
The delay between applying the digital control input and the
output switching on. See Figure 29, Test Circuit 4.
tOFF (EN)
The delay between applying the digital control input and the
output switching off.
Charge Injection
A measure of the glitch impulse transferred from the digital
input to the analog output during switching.
IS (Off)
The source leakage current with the switch off.
ID (Off)
The drain leakage current with the switch off.
Off Isolation
A measure of unwanted signal coupling through an off switch.
ID, IS (On)
The channel leakage current with the switch on.
Crosstalk
A measure of unwanted signal that is coupled through from one
channel to another as a result of parasitic capacitance.
VINL
The maximum input voltage for Logic 0.
Bandwidth
The frequency at which the output is attenuated by 3 dB.
VINH
The minimum input voltage for Logic 1.
On Response
The frequency response of the on switch.
IINL (IINH)
The input current of the digital input.
Insertion Loss
The loss due to the on resistance of the switch.
CS (Off)
The off switch source capacitance, which is measured with
reference to ground.
THD + N
The ratio of the harmonic amplitude plus noise of the signal to
the fundamental.
CD (Off)
The off switch drain capacitance, which is measured with
reference to ground.
CD, CS (On)
The on switch capacitance, which is measured with reference to
ground.
ACPSRR (AC Power Supply Rejection Ratio)
The ratio of the amplitude of signal on the output to the
amplitude of the modulation. This is a measure of the part’s
ability to avoid coupling noise and spurious signals that appear
on the supply voltage pin to the output of the switch. The dc voltage
on the device is modulated by a sine wave of 0.62 V p-p.
Rev. A | Page 12 of 16
ADG1404
TEST CIRCUITS
VDD
VSS
0.1µF
0.1µF
VDD
NETWORK
ANALYZER
VSS
50Ω
Sx
50Ω
VS
V
Sx
D
RL
50Ω
GND
D
VOUT
06816-020
06816-027
IDS
VS
VOUT
VS
OFF ISOLATION = 20 log
Figure 25. Off Isolation
Figure 22. On Resistance
VDD
VSS
0.1µF
0.1µF
VDD
NETWORK
ANALYZER
VSS
50Ω
Sx
VS
D
Sx
D
GND
A
VD
06816-021
VS
VOUT WITH SWITCH
VOUT WITHOUT SWITCH
INSERTION LOSS = 20 log
Figure 23. Off Leakage
VOUT
Figure 26. Bandwidth
VDD
VSS
0.1µF
0.1µF
NETWORK
ANALYZER
VOUT
VDD
S1
VSS
RL
50Ω
D
S2
VS
NC = NO CONNECT
A
VD
06816-022
NC
D
RL
50Ω
GND
ID (ON)
Sx
06816-028
A
RL
50Ω
ID (OFF)
CHANNEL-TO-CHANNEL CROSSTALK = 20 log
VOUT
VS
Figure 27. Channel-to-Channel Crosstalk
Figure 24. On Leakage
Rev. A | Page 13 of 16
06816-029
IS (OFF)
ADG1404
VDD
VSS
0.1µF
0.1µF
AUDIO PRECISION
VDD
VSS
RS
Sx
IN
VS
V p-p
D
VIN
VOUT
RL
110Ω
06816-030
GND
Figure 28. THD + Noise
VDD VSS
0.1µF
VDD VSS
S1
A1
S2
A0
S3
S4
VIN
2.4V
EN
GND
ADDRESS
DRIVE (VIN)
VS1
VS4
3V
50%
VOUT
tTRANSITION
CL
35pF
RL
300Ω
90%
90%
VOUT
D
50%
0V
tTRANSITION
06816-023
0.1µF
Figure 29. Address to Output Switching Times
VIN
300Ω
2.4V
VDD VSS
0.1µF
VDD VSS
S1
A1
S2
A0
S3
S4
EN
GND
ADDRESS
DRIVE (VIN)
VS1
VOUT
D
RL
300Ω
CL
35pF
0V
VOUT
Figure 30. Break-Before-Make Time Delay
Rev. A | Page 14 of 16
3V
80%
80%
tBBM
06816-024
0.1µF
ADG1404
VDD VSS
0.1µF
VDD VSS
S1
A1
S2
A0
S3
S4
EN
GND
VS
3V
50%
VOUT
0.9VOUT
OUTPUT
D
RL
300Ω
300Ω
CL
35pF
VOUT
50%
0V
0.9VOUT
0V
tON (EN)
tOFF (EN)
Figure 31. Enable-to-Output Switching Delay
VDD
VSS
VDD
VSS
Sx
D
VOUT
RS
VS
DECODER
ΔVOUT
QINJ = CL × ΔVOUT
VOUT
VIN
CL
1nF
SW OFF
SW OFF
SW ON
GND
VIN
A1 A2
SW OFF
SW OFF
06816-026
VIN
ENABLE
DRIVE (VIN)
06816-025
0.1µF
EN
Figure 32. Charge Injection
Rev. A | Page 15 of 16
ADG1404
OUTLINE DIMENSIONS
5.10
5.00
4.90
14
8
4.50
4.40
4.30
6.40
BSC
1
7
PIN 1
0.65 BSC
1.20
MAX
0.15
0.05
COPLANARITY
0.10
0.30
0.19
0.20
0.09
0.75
0.60
0.45
8°
0°
SEATING
PLANE
061908-A
1.05
1.00
0.80
COMPLIANT TO JEDEC STANDARDS MO-153-AB-1
Figure 33. 14-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-14)
Dimension shown in millimeters
4.00
BSC SQ
0.60 MAX
12 13
3.75
BSC SQ
TOP VIEW
12° MAX
1.00
0.85
0.80
SEATING
0.30
PLANE
0.23
0.18
1
16
EXPOSED
PAD
0.65
BSC
4
8
9
PIN 1
INDICATOR
2.65
2.50 SQ
2.35
5
0.25 MIN
1.95 BCS
0.80 MAX
0.65 TYP
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.20 REF
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VGGC.
031006-A
PIN 1
INDICATOR
0.50
0.40
0.30
Figure 34. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad
(CP-16-13)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADG1404YRUZ1
ADG1404YRUZ-REEL71
ADG1404YCPZ-REEL1
ADG1404YCPZ-REEL71
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
14-Lead Thin Shrink Small Outline Package (TSSOP)
14-Lead Thin Shrink Small Outline Package (TSSOP)
16-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
16-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
Z = RoHS Compliant Part.
©2008–2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06841-0-3/09(A)
Rev. A | Page 16 of 16
Package Option
RU-14
RU-14
CP-16-13
CP-16-13