RoHS BR1505W-1510W SINGLE-PHASE BRIDGE RECTIFIER FEATURES Low cost This series is UL recognized under component index, file number E127707 High forward surge current capability Intergrally molded heatsink provide very low thermal resistance. High isolation voltage from case to leads. High temperature soldering guaranteed: 260/10 second, at 5 lbs. (2.3kg) tension. MECHANICAL DATA Case: Molded plastic body, suffic "N" for thinner type Terminal: Plated lead 0.040" (1.02mm) diameter. Polarity: Polarity symbols marked on case. Mounting: Thru hole for #10 screw, 20 in,- lbs. Torqute Max. Weight: 0.61 ounce, 17.4 gram (BR15W) O MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load derate current by 20% C E L Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Output Current, at TC = 55 (Note 1, 2) Peak Forward Surge Current 8.3ms single half sine - wave superimposed on rated load (JEDEC method ) Rating for Fusing (t<8.3ms) Maximum Instantaneous Forward Voltage Drop per bridge element at 7.5A Maximum DC Reverse Current at rate TA = 25 DC blocking voltage per element TA Isolation Voltage from case to leads Typical Thermal Resistance (Note 1,2) Operating Temperature Range Storage Temperature Range J E R T IC C D T ,. L O N SYMBOLSBR1505WBR151W BR152W BR154W BR156W BR158W BR1510W VRRM Volts VRMS Volts VDC Volts E W I(AV) Amps IFSM Amps 2 2 It VF IR VISO R TJ TSTG As Volts 2.0 (-65 to +150) (-65 to +150) A mA VAC /W 1. Unit mounted on 5" X 4" X 3" (12.8cm X 10.2cm X 7.3cm)Al. finned Plate. 2. Bolt down on heat-sink with silicon thermal compound between bridge and mounting sutfae for maximum heat transfer efficiency with # 10 screw. WEJ ELECTRONIC CO. Http:// www.wej.cn E-mail:[email protected] RoHS BR1505W-1510W FIG.1-DERATING CURVE FOR FIG.2-MAXIMUM NON-REPETITIVE PEAK OUTPUT RECTIFIED CURRENT FORWARD SURGE CURRENT PER ELEMENT Heat Sink Mounting AL.Finned Plate Single Phase Half Wave 60Hz 5.0 Inductive or Resistive Load CURRENT, (A) (12.8 X 10.2 X 7.3cm) 10 300 PEAK FORWARD SURGE 5" X 4" X 3" Thick CURRENT,(A) AVERAGE FORWARD OUTPUT 15 200 100 1 Cycle 0 0 50 55 25 75 125 100 150 175 0 1 NUMBER OF CYCLES AT 60 Hz PER BRIDGE ELEMENT 1.0 R T Tj =25 ° C Pulse Width=300uS 1%Duty Cycle 0.1 C E L 1.0 0.8 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE,(V) N O 10 (uA) INSTANTANEOUS REVERSE CURRENT, 10 (A) IC 100 0.6 CHARACTERISTICS PER BRIDGE ELEMENT 100 INSTANTANEOUS FORWARD CURRENT, C FIG.4-TYPICAL REVERSE FIG.3-TYPICAL FORWARD CHARACTERISTICS 0.4 j max 100 10 CASE TEMPERATURE, ( ° C) 0.01 D T ,. L O 8.3ms Single Half Sine-Wave Tj (JEDEC Method) =T Tj =100 ° C 1.0 Tj =25 ° C 0.1 0.01 1.8 60 40 20 0 120 100 80 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE E FIG.6-MAXIMUM POWER DISSIPATION PER BRIDGE ELEMENT W T j=25 ° C f=1MHz V sig =50mV p-p 10 0.1 1.0 10 100 REVRESE VOLTAGE,(V) WEJ ELECTRONIC CO. Http:// www.wej.cn 80 (W) JUNCTION CAPACITANCE,(pF) J E 100 100 AVERAGE POWER DISSIPATION OF BRIDGE, 1000 Tj =T j max 60 Capacitive Load 40 Resistive or Inductive 20 Load 0 0 5 10 15 20 25 30 35 AVERAGE OUTPUT CURRENT, (A) E-mail:[email protected]