November 1, 2011 SMD INDUCTOR DR354-2 SERIES Features SMD Chip Inductor, Low Profile Suitable for High Frequency Application Inductance Range from 2.2nH to 820nH Operating Temp. -40°C to +125°C Tinned Leads with Leaded Solder is Available (note 6) ELECTRICAL SPECIFICATIONS AT 25ºC PART NO. DR354-2-222-T DR354-2-332-T DR354-2-682-T DR354-2-872-T DR354-2-103-T DR354-2-123-T DR354-2-153-T DR354-2-183-T DR354-2-223-T DR354-2-273-T DR354-2-333-T DR354-2-393-T DR354-2-473-T DR354-2-563-T DR354-2-683-T DR354-2-823-T DR354-2-104-T DR354-2-124-T DR354-2-154-T DR354-2-184-T DR354-2-224-T DR354-2-274-T DR354-2-334-T DR354-2-394-T DR354-2-474-T DR354-2-564-T DR354-2-684-T DR354-2-824-T PERCENT TOLERANCE, T 20, 10 20, 10 20, 10, 5 20, 10 20, 10, 5 10, 5, 2 20, 10, 5 10, 5, 2 10, 5, 2 10, 5, 2 10, 5, 2 10, 5, 2 10, 5, 2 10, 5, 2 10, 5, 2 10, 5, 2 10, 5, 2 10, 5, 2 10, 5, 2 20, 10, 5 20, 10, 5 20, 10, 5 20, 10, 5 20, 10, 5 20, 10, 5 20, 10, 5 20, 10, 5 20, 10, 5 INDUCTANCE (nH) 2.2 @250MHz 3.3 @250MHz 6.8 @250MHz 8.2 @250MHz 10 @250MHz 12 @250MHz 15 @250MHz 18 @250MHz 22 @250MHz 27 @250MHz 33 @250MHz 39 @250MHz 47 @200MHz 56 @200MHz 68 @200MHz 82 @150MHz 100 @150MHz 120 @150MHz 150 @100MHz 180 @100MHz 220 @100MHz 270 @100MHz 330 @100MHz 390 @100MHz 470 @50MHz 560 @50MHz 680 @50MHz 820 @50MHz DCR () MAX. 0.08 0.08 0.11 0.12 0.14 0.15 0.17 0.20 0.22 0.25 0.27 0.29 0.31 0.34 0.38 0.42 0.46 0.51 0.56 0.64 0.70 1.10 1.40 1.50 1.76 1.90 2.20 2.35 MAX. RATED CURRENT (A) 0.600 0.600 0.600 0.600 0.600 0.600 0.600 0.600 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.400 0.400 0.400 0.400 0.400 0.400 0.350 0.310 0.290 0.250 0.230 0.190 0.180 INDUCTANCE TOLERANCE: WHEN ORDERING, PLEASE SPECIFY THE TOLERANCE. -T (M=±20%, K=±10%, J=±5%, G=±2%) DATATRONIC: 28151 Highway 74, Romoland, CA 92585 Tel: 951-928-7700 Fax: 951-928-7701 Email: [email protected] 499 King’s Road, Hong KongTel: (852) 2562 3858, (852) 2564 8477 Fax: (852) 2565 7214, (852) 2563 1290 All specifications are subject to change without notice Page 1 of 2 November 1, 2011 MECHANICAL OUTLINES Q VS FREQUENCY RESPONSE Ls VS FREQUENCY RESPONSE Notes: 1. All dimensions are shown in millimeter “mm” 2. General tolerance 0.1mm, unless other specified 3. Tape and reel quantity, 3000 pcs/reel 4. Terminal finish is compliant to RoHS requirements and is gold plated 5. Solder in accordance with J-STD-002 Rev. D 6. Non-RoHS series parts 42-354-2-XXX are finished with leaded solder Sn60Pb40 or equivalent DATATRONIC: 28151 Highway 74, Romoland, CA 92585 Tel: 951-928-7700 Fax: 951-928-7701 Email: [email protected] 499 King’s Road, Hong KongTel: (852) 2562 3858, (852) 2564 8477 Fax: (852) 2565 7214, (852) 2563 1290 All specifications are subject to change without notice Page 2 of 2