CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead Upgrade! @Super low ESR, high ripple current capability @ESR 5mO max. (2 & 2.5Vdc) @Longer life (5,000 hours at 105C) @ESR after endurance is specified within the initial spec (2 & 2.5Vdc) @Rated voltage range : 2 to 16Vdc @RoHS Compliant @Halogen Free PSF Lower ESR PSE ?SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current -55 to +105C *Note 2 to 16Vdc P20% (M) Rated voltage(V)B1.15 I=0.2CV or 500MA, whichever is greater Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V) Dissipation Factor (tane) 0.10 max. Low Temperature Characteristics (Max.Impedance Ratio) Z(-25C)/Z(+20C)[1.15 Z(-55C)/Z(+20C)[1.25 Endurance Bias Humidity Test Surge Voltage Test Failure Rate (at 20C, 120Hz) (at 105C) (at 20C after 2 minutes) (at 20C, 120Hz) (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 5,000 hours at 105C. Appearance No significant damage Capacitance change [P20% of the initial value D.F. (tanE) [The initial specified value ESR 2 & 2.5Vdc : [The initial specified value 16Vdc : [150% of the initial specified value Leakage current [The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to DC voltage at 60C, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change [P20% of the initial value D.F. (tanE) [The initial specified value ESR 2 & 2.5Vdc : [The initial specified value 16Vdc : [150% of the initial specified value Leakage current [The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change [P20% of the initial value D.F. (tanE) [The initial specified value ESR 2 & 2.5Vdc : [The initial specified value 16Vdc : [150% of the initial specified value Leakage current [The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105C) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105C. ?DIMENSIONS [mm] Coated Case Size code F05 F08 fD 6.3 fd 0.45 0.6 F 2.5 fD' L' L+1.0max. FD' Fd F05, F08, H08 FP0.5 @Terminal Code : E (F05, F08, H08) FP0.5 Coated Case FD' (FA5) L' 15min. H08 HB5 8.0 JB5 10.0 0.6 0.5 3.5 FD+0.5max. L+0.3max. L+1.0max. 5.0 L+1.5max. 4min. Fd FA5, HB5, JB5 15min. FP0.5 L' FA5 (HB5, JB5) ?MARKING EX) 2.5V560MF F 6D6 560 2.5V 4min. (1/2) CAT. No. E1001K CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead Upgrade! ?PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A PS F 2 R 5 E AA 5 6 1 M F 0 8 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 560MF:561) Lead forming·Taping code Terminal code Voltage code (ex. 2.5V:2R5, 16V:160) Series code Category Please refer to "Product code guide (conductive polymer type)" ?STANDARD RATINGS WV(Vdc) Cap(mF) 2 1,000 330 470 560 820 1,600 100 100 270 270 330 470 470 2.5 16 Case size fDbL(mm) ESR (mo max./20c, 100k to 300kHz) 6.3B8 6.3B8 6.3B8 6.3B8 6.3B8 8B8 6.3B5 6.3B10.5 8B8 8B11.5 8B8 8B11.5 10B11.5 5 5 5 5 5 5 24 25 10 11 13 11 10 Rated ripple current (mArms/105c, 100kHz) 5,900 5,900 5,900 5,900 5,900 6,100 2,490 2,820 5,000 5,080 4,700 5,400 6,100 Part No. APSF2R0ESS102MF08S APSF2R5ESS331MF08S APSF2R5ESS471MF08S APSF2R5ESS561MF08S APSF2R5ESS821MF08S APSF2R5ESS162MH08S APSF160ESS101MF05S APSF160ESS101MFA5S APSF160ESS271MH08S APSF160ESS271MHB5S APSF160ESS331MH08S APSF160ESS471MHB5S APSF160ESS471MJB5S SS : Enter the appropriate lead forming or taping code. (2/2) CAT. No. E1001K