STATEK CX1HSM Miniature surface mount quartz crystal for series oscillator Datasheet

CX1HSM CRYSTAL
10 kHz to 600 kHz
Miniature Surface Mount
Quartz Crystal for Series Oscillators
DESCRIPTION
The CX1HSM quartz crystal is a high quality tuning fork
resonator for use in Series (two cascaded inverters)
oscillators. The CX1HSM is hermetically sealed in a rugged,
miniature ceramic package. The CX1HSM crystal is
manufactured using the STATEK-developed photolithographic process, and was designed utilizing the
experience acquired by producing millions of crystals for
industrial, commercial, military and medical applications.
Maximum process temperature should not exceed 260OC.
Actual size
Side view
Glass Lid Shown
PACKAGE DIMENSIONS
FEATURES
Miniature tuning fork design
High shock resistance
Designed for low power applications
Compatible with hybrid or PC board packaging
Low aging
Full military testing available
Designed and manufactured in the USA
EQUIVALENT CIRCUIT
TYP.
MAX.
DIM
inches
mm
inches
mm
A
0.315
8.00
0.330
8.38
B
0.140
3.56
0.155
3.94
C
-
-
D
0.045
1.14
0.055
1.40
E
0.060
1.52
0.070
1.78
DIM “C”
see below
GLASS LID
CERAMIC LID
MAX
inches
mm
inches
mm
SM1
0.065
1.65
0.070
1.78
SM2/SM4
0.067
1.70
0.072
1.83
SM3/SM5
0.070
1.78
0.075
1.90
CONVENTIONAL SERIES
OSCILLATOR CIRCUIT
SUGGESTED LAND PATTERN
10122 - Rev E
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
FIGURE 1
CX1H TYPICAL MOTIONAL RESISTANCE (R1)
SPECIFICATIONS
Specifications are typical at 25OC unless otherwise noted.
Specifications are subject to change without notice.
Frequency Range
10 kHz to 600 kHz
Standard Calibration Tolerance1 (see table below)
Motional Resistance (R1)
Figure 1
MAX.: 10-169.9 kHz, 2x Typ.
170-600 kHz, 2.5x Typ.
Motional Capacitance (C1) Figure 2
Quality Factor (Q)
Figure 3
Min. is 0.25x Typ.
Shunt Capacitance (C0)
2.0 pF MAX
Drive Level
10-24.9 kHz 1.5 µW MAX
25-600 kHz 3.0 µW MAX
2
Turning Point (T0)
Figure 4
Temperature Coefficient (k) -0.035 ppm/OC2
Aging, first year
5 ppm MAX
3
Shock, survival
1,000 g, 1ms, 1/2 sine
3
Vibration, survival
20 g RMS, 10-2,000 Hz
Operating Temp. Range
-10OC to +70OC (Commercial)
-40OC to +85OC (Industrial)
-55OC to +125OC (Military)
Storage Temp. Range
-55OC to +125OC
Max Process Temperature 260O C for 20 sec.
FIGURE 2
CX1H TYPICAL MOTIONAL CAPACITANCE (C1)
FIGURE 3
CX1H TYPICAL QUALITY FACTOR (Q)
1. Tighter frequency calibration available.
2. Other turning point available.
3. Higher shock and vibration available.
CX1HSM Standard Calibration Tolerance at 25OC
Frequency Range (kHz)
10-74.9
75-169.9
170-249.9
250-600
30 ppm
(0.003%)
50 ppm
(0.005%)
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_
100 ppm
(0.01%)
+
_
100 ppm
(0.01%)
100 ppm
(0.01%)
+
_
1000 ppm
(0.1%)
1000 ppm
(0.1%)
200 ppm
(0.02%)
200 ppm
(0.02%)
+
_
500 ppm
(0.05%)
FIGURE 4
CX1H TYPICAL TURNING POINT TEMP. (T0)
+
_
2000 ppm
(0.2%)
5000 ppm
(0.5%)
HOW TO ORDER CX1HSM CRYSTALS
CX1H
S
“S” if special or
custom design.
Blank if Std.
Blank= Glass Lid
C=Ceramic Lid
C
SM1
32.768K
,
Frequency
K = kHz
SM1 = Gold Plated (Lead Free)
SM2 = Solder Plated
SM3 = Solder Dipped
SM4 = Solder Plated (Lead Free)
SM5 = Solder Dipped (Lead Free)
30
Calibration
Tolerance
@ 25OC
(in ppm)
TERMINATIONS
Designation
SM1
SM2
SM3
SM4
SM5
Termination
Gold Plated (Lead Free)
Solder Plated
Solder Dipped
Solder Plated (Lead Free)
Solder Dipped (Lead Free)
/
I
Operating Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
Note: Frequency f at temperature T is related to frequency f0 at
turning point temperature T0 by: f-f
2
0
= k(T-T0)
f0
PACKAGING
CX1HSM
- Tray Pack
- 16mm tape, 7” or 13” reels
(Reference tape and reel data sheet 10109)
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
10122 - Rev E
Similar pages