E200I Series High Isolation, 2W Ultra-Miniature, SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: Input Parameter Conditions 5 VDC Input Min. 4.5 Typ. 5.0 Max. 5.5 12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 48 VDC Input 44.0 48.0 52.0 • 2W Output Power • Ultra-Miniature SIP Case Input Voltage Range • 3,000 VDC Isolation • >2 MHour MTBF • 18 Standard Models • Industry Standard Pin-Out Reverse Polarity Input Current Input Filter VDC 0.3 A Max. ±3.0 Units % Internal Capacitor Output Parameter Output Voltage Accuracy Line Regulation Load Regulation (Note 1) Conditions Min. Typ. For Vin Change of 1% ±1.2 % See Model Selection Guide Ripple & Noise (20 MHz) (Note 2) Output Power Protection 100 mV P - P ±0.02 %/ºC Max. Units VDC 120 Temperature Coefficient RoHS Compliant Units % ±0.01 Output Short Circuit Momentary (0.5 Sec.) General Parameter Isolation Voltage Conditions Isolation Resistance Isolation Capacitance 60 Seconds Min. 3,000 1,000 VDC 1,000 100 kHz, 1V Switching Frequency Typ. MΩ 60 pF 125 kHz Environmental Parameter Operating Temperature Range Conditions Ambient Operating Temperature Range -55 Cooling MicroPower Direct Physical 292 Page Street Suite D Stoughton, MA 02072 USA Case Size Case Material T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter MTBF Typ. +25 Case Storage Temperature Range Humidity Min. -40 Max. +85 Units ºC +90 ºC +125 ºC 95 % Free Air Convection RH, Non-condensing 0.46 x 0.29 x 0.40 Inches (11.68 x 7.5 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) Weight 0.06 Oz (1.8g) Reliability Specifications Conditions MIL HDBK 217F, 25ºC, Gnd Benign Min. 2.0 Typ. Max. Units MHours Conditions Min. -0.7 Typ. Max. 9.0 Units 5 VDC Input 12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 48 VDC Input -0.7 55.0 Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation VDC 1.5 mm From Case For 10 Sec 260 ºC All Models 650 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number E201I Input Output Load Voltage (VDC) Current (mA) Voltage Current Current Regulation Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (% Max) 5 4.5 - 5.5 372 38 3.3 400.0 40.0 12 Efficiency (%, Typ) 71 Fuse Rating Slow-Blow (mA) 1,000 E202I 5 4.5 - 5.5 533 38 5.0 400.0 40.0 12 75 1,000 E203I 5 4.5 - 5.5 500 38 9.0 222.0 22.0 8 79 1,000 E204I 5 4.5 - 5.5 500 38 12.0 167.0 16.0 8 80 1,000 E205I 5 4.5 - 5.5 500 38 15.0 133.0 13.0 8 80 1,000 E211I 12 10.8 - 13.2 150 30 3.3 400.0 40.0 8 73 500 E212I 12 10.8 - 13.2 200 30 5.0 400.0 40.0 8 77 500 E213I 12 10.8 - 13.2 211 30 9.0 222.0 22.0 8 79 500 E214I 12 10.8 - 13.2 199 25 12.0 167.0 16.0 8 84 500 E215I 12 10.8 - 13.2 208 25 15.0 133.0 13.0 8 80 500 E222I 24 21.6 - 26.4 107 12 5.0 400.0 40.0 8 78 200 E223I 24 21.6 - 26.4 102 12 9.0 222.0 22.0 8 82 200 E224I 24 21.6 - 26.4 104 12 12.0 167.0 16.0 8 80 200 E225I 24 21.6 - 26.4 102 12 15.0 133.0 13.0 8 82 200 E232I 48 44.0 - 52.0 53 6 5.0 400.0 40.0 8 78 100 E233I 48 44.0 - 52.0 52 6 9.0 222.0 22.0 8 80 100 E234I 48 44.0 - 52.0 53 6 12.0 167.0 16.0 8 78 100 E235I 48 44.0 - 52.0 52 6 15.0 133.0 13.0 8 80 100 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external 0.33 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin. 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. The 5V, 12V and 24V input units do not require external components to operate, but the use of a low ESR capacitor (approximately 10 µF, ESR <1.0Ω at 100 kHz) mounted close to the converter input pins is recommended. For 48 VDC input units, an input capacitor should always be used. Dependent upon the application, a value between 4.7 µF and 47 µF should be sufficient. 5. Out put capacitive load capability of these units is 33 µF max. Exceeding this may cause start up problems. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Pin Connections Pin Description 1 -Vin 2 +Vin 3 -Vout 4 +Vout Derating Curve Mechanical Dimensions Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]