TDK B4371A4228M000 Capacitors with screw terminal Datasheet

Aluminum electrolytic capacitors
Capacitors with screw terminals
Series/Type:
B43701, B43721
Date:
October 2015
© EPCOS AG 2015. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
EPCOS AG is a TDK Group Company.
Capacitors with screw terminals
B43701, B43721
Standard 85 °C
Long-life grade capacitors
Applications
Uninterruptible power supplies
Frequency converters
Features
All-welded construction ensures reliable electrical contact
RoHS-compatible
Construction
Charge-discharge proof, polar
Aluminum case with insulating sleeve
Poles with screw terminal connections
Mounting with ring clips, clamps or threaded stud
The bases of types with threaded stud are not insulated
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 17
B43701
B43721
B43701, B43721
Standard 85 °C
Specifications and characteristics in brief
Rated voltage VR
Surge voltage VS
Rated capacitance CR
Capacitance tolerance
350 ... 450 V DC
1.10 VR
1200 ... 12000 µF
±20% M
Dissipation factor tan δ
(20 °C, 120 Hz)
≤ 0.20
Leakage current Ileak
(20 °C, 5 min)
Self-inductance ESL
Useful life1)
85 °C; VR; IAC,R
d = 51.6 mm: approx. 15 nH
d ≥ 64.3 mm: approx. 20 nH
Requirements:
∆C/C ≤ 15% of initial value
tan δ
≤ 1.75 times initial specified limit
Ileak
≤ initial specified limit
Voltage endurance test
Post test requirements:
85 °C; VR
2000 h
∆C/C ≤ 10% of initial value
tan δ
≤ 1.3 times initial specified limit
Ileak
≤ initial specified limit
Vibration resistance test To IEC 60068-2-6, test Fc:
Frequency range 10 ... 55 Hz, displacement amplitude 0.75 mm,
acceleration max. 10 g, duration 3 × 2 h. Capacitor mounted by its
body which is rigidly clamped to the work surface.
Max. impedance
Characteristics at low
Z -25°C / Z 20°C
3
ratio at 100 Hz
temperature
Z -40°C / Z 20°C
17
> 5000 h
IEC climatic category
To IEC 60068-1:
25/085/56 (25 °C/+85 °C/56 days damp heat test)
Detail specification
Sectional specification
Similar to CECC 30301-810
IEC 60384-4
Ripple current capability
Due to the ripple current capability of the contact elements, the following current upper limits must
not be exceeded:
Capacitor diameter
51.6 mm
64.3 mm
76.9 mm
IAC,max
34 A
47 A
57 A
1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 17
B43701, B43721
Standard 85 °C
Dimensional drawings
B43701
Ring clip/clamp mounting
B43721
Threaded stud mounting
For types with threaded stud the base is not insulated. Also refer to the mounting instructions in
chapter "Capacitors with screw terminals Accessories".
Dimensions and weights (Standard capacitors, without heat sink)
Terminal
Dimensions (mm) with insulating sleeve
d
l ±1
l1 ±1
l2 +0/1 d1
d2 max. a +0.2/0.4
M5
M5
M5
M5
M5
51.6 +0.5/1 80.7
51.6 +0.5/1 96.7
51.6 +0.5/1 105.7
51.6 +0.5/1 118.2
51.6 +0.5/1 130.7
87.2
103.2
112.2
124.7
137.2
17
17
17
17
17
M12
M12
M12
M12
M12
10.2
10.2
10.2
10.2
10.2
22.2
22.2
22.2
22.2
22.2
220
250
280
320
350
M5
M5
M5
M5
M5
M5
64.3 +0.5/1
64.3 +0.5/1
64.3 +0.5/1
64.3 +0.5/1
64.3 +0.5/1
64.3 +0.5/1
80.7
96.7
105.7
118.2
130.7
143.2
87.2
103.2
112.2
124.7
137.2
149.7
17
17
17
17
17
17
M12
M12
M12
M12
M12
M12
13.2
13.2
13.2
13.2
13.2
13.2
28.5
28.5
28.5
28.5
28.5
28.5
370
400
440
510
600
630
M5
M5
M5
M5
M5
M5
76.9 +0.5/1
76.9 +0.5/1
76.9 +0.5/1
76.9 +0.5/1
76.9 +0.5/1
76.9 +0.5/1
96.7
105.7
130.7
156.2
168.7
190.7
103.2
112.2
137.2
162.7
175.2
197.2
17
17
17
17
17
17
M12
M12
M12
M12
M12
M12
13.2
13.2
13.2
13.2
13.2
13.2
31.7
31.7
31.7
31.7
31.7
31.7
570
620
800
920
1000
1150
Please read Cautions and warnings and
Important notes at the end of this document.
Page 4 of 17
Approx.
weight (g)
B43701, B43721
Standard 85 °C
Packing
Capacitor
diameter d (mm)
51.6
64.3
76.9
length l
(mm)
all
all
≤168.7
>168.7
Packing units
(pcs.)
36
25
16
12
For ecological reasons the packing is pure cardboard.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 5 of 17
B43701, B43721
Standard 85 °C
Accessories
The following items are included in the delivery package, but are not fastened to the capacitors:
For terminals
Thread Toothed
washers
Screws/nuts
Maximum
torque
M5
DIN 7985 / ISO 7045-M5 × 10-5.6-Z
2.5 Nm
thread depth
t ≥ 8 mm
For mounting M12
A 5.1 DIN 6797
J 12.5 DIN 6797 Hex nut BM 12 DIN 439
10 Nm
The following items must be ordered separately. For details, refer to chapter "Screw terminals Accessories".
Item
Ring clips
Clamps for capacitors with d ≥ 64.3 mm
Insulating parts
Please read Cautions and warnings and
Important notes at the end of this document.
Type
B44030
B44030
B44020
Page 6 of 17
B43701, B43721
Standard 85 °C
Overview of available types
VR (V DC)
350
400
450
Case dimensions d × l (mm)
CR (µF)
51.6 × 80.7
1200
1500
51.6 × 80.7
51.6 × 96.7
1800
51.6 × 80.7
51.6 × 96.7
51.6 × 96.7
2200
51.6 × 96.7
51.6 × 105.7
64.3 × 80.7
51.6 × 118.2
64.3 × 96.7
2700
51.6 × 105.7
51.6 × 118.2
64.3 × 96.7
51.6 × 130.7
64.3 × 96.7
3300
51.6 × 118.2
64.3 × 96.7
64.3 × 96.7
64.3 × 105.7
3900
51.6 × 130.7
64.3 × 96.7
64.3 × 105.7
64.3 × 118.2
76.9 × 96.7
4700
64.3 × 105.7
64.3 × 130.7
76.9 × 96.7
64.3 × 143.2
76.9 × 105.7
5600
64.3 × 118.2
76.9 × 96.7
64.3 × 143.2
76.9 × 105.7
76.9 × 130.7
6800
64.3 × 143.2
76.9 × 105.7
76.9 × 130.7
76.9 × 156.2
8200
76.9 × 130.7
76.9 × 156.2
76.9 × 190.7
10000
76.9 × 156.2
76.9 × 168.7
76.9 × 190.7
12000
76.9 × 168.7
76.9 × 190.7
The capacitance and voltage ratings listed above are available in different cases upon request.
Other voltage and capacitance ratings are also available upon request.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 17
B43701, B43721
Standard 85 °C
Technical data and ordering codes
CR
100 Hz
20 °C
µF
Case
dimensions
d×l
mm
VR = 350 V DC
1800
51.6 × 80.7
2200
51.6 × 96.7
2700
51.6 × 105.7
3300
51.6 × 118.2
3300
64.3 × 96.7
3900
51.6 × 130.7
3900
64.3 × 96.7
4700
64.3 × 105.7
5600
64.3 × 118.2
5600
76.9 × 96.7
6800
64.3 × 143.2
6800
76.9 × 105.7
8200
76.9 × 130.7
10000
76.9 × 156.2
12000
76.9 × 168.7
VR = 400 V DC
1500
51.6 × 80.7
1800
51.6 × 96.7
2200
51.6 × 105.7
2200
64.3 × 80.7
2700
51.6 × 118.2
2700
64.3 × 96.7
3300
64.3 × 96.7
3900
64.3 × 105.7
4700
64.3 × 130.7
4700
76.9 × 96.7
5600
64.3 × 143.2
5600
76.9 × 105.7
6800
76.9 × 130.7
8200
76.9 × 156.2
10000
76.9 × 168.7
12000
76.9 × 190.7
ESRtyp
100 Hz
20 °C
mΩ
ESRtyp
300 Hz
60 °C
mΩ
Zmax
10 kHz
20 °C
mΩ
IAC,max
100 Hz
60 °C
A
IAC,R
100 Hz
85 °C
A
Ordering code
(composition see
below)
75
60
50
40
45
36
38
32
28
26
22
22
18
15
13
22
18
15
13
15
11
14
13
11
9.7
9.1
8.6
6.8
5.7
5.2
120
100
80
70
70
60
65
55
50
45
38
38
30
26
22
11.7
13.5
15.3
17.5
16.4
19.6
17.5
19.3
21.5
23.8
24.8
26.2
30.1
34.3
37.9
6.98
8.01
9.10
10.3
9.72
11.5
10.3
11.4
12.6
14.0
14.6
15.5
17.8
20.3
22.9
B437*1A4188M000
B437*1A4228M000
B437*1A4278M000
B437*1A4338M000
B437*1B4338M000
B437*1A4398M000
B437*1B4398M000
B437*1A4478M000
B437*1A4568M000
B437*1B4568M000
B437*1A4688M000
B437*1B4688M000
B437*1A4828M000
B437*1A4109M000
B437*1A4129M000
80
65
55
60
45
45
40
34
28
28
24
24
20
16
14
12
24
19
16
20
14
16
15
13
11
10
9.4
9.0
7.1
5.9
5.3
4.7
130
110
90
95
75
80
70
60
50
50
40
40
32
28
24
20
11.3
12.8
14.6
13.7
16.7
15.8
17.1
18.8
21.8
23.1
24.2
25.4
29.3
33.3
37.2
41.8
6.59
7.49
8.50
8.00
9.73
9.18
9.93
10.9
12.6
13.4
14.0
14.7
17.0
19.3
22.1
24.8
B437*1A9158M000
B437*1A9188M000
B437*1A9228M000
B437*1B9228M000
B437*1A9278M000
B437*1B9278M000
B437*1A9338M000
B437*1A9398M000
B437*1A9478M000
B437*1B9478M000
B437*1A9568M000
B437*1B9568M000
B437*1A9688M000
B437*1A9828M000
B437*1A9109M000
B437*1A9129M000
Composition of ordering code
* = Mounting style
0 = for capacitors with ring clip/clamp mounting
2 = for capacitors with threaded stud
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 17
B43701, B43721
Standard 85 °C
Technical data and ordering codes
CR
100 Hz
20 °C
µF
Case
dimensions
d×l
mm
VR = 450 V DC
1200
51.6 × 80.7
1500
51.6 × 96.7
1800
51.6 × 96.7
2200
51.6 × 118.2
2200
64.3 × 96.7
2700
51.6 × 130.7
2700
64.3 × 96.7
3300
64.3 × 105.7
3900
64.3 × 118.2
3900
76.9 × 96.7
4700
64.3 × 143.2
4700
76.9 × 105.7
5600
76.9 × 130.7
6800
76.9 × 156.2
8200
76.9 × 190.7
10000
76.9 × 190.7
ESRtyp
100 Hz
20 °C
mΩ
ESRtyp
300 Hz
60 °C
mΩ
Zmax
10 kHz
20 °C
mΩ
IAC,max
100 Hz
60 °C
A
IAC,R
100 Hz
85 °C
A
Ordering code
(composition see
below)
95
75
65
50
55
45
45
38
32
32
26
26
22
18
15
13
26
22
19
15
17
13
16
14
12
11
9.9
9.4
7.6
6.3
5.2
4.9
150
120
100
85
85
70
75
65
55
50
45
45
36
30
26
22
9.82
11.3
12.6
14.6
14.0
16.8
15.4
17.2
19.1
20.9
22.0
23.1
26.3
29.9
34.1
37.8
5.36
6.22
6.91
8.00
7.66
9.18
8.38
9.37
10.4
11.3
11.9
12.6
14.3
16.3
19.1
21.0
B437*1A5128M000
B437*1A5158M000
B437*1A5188M000
B437*1A5228M000
B437*1B5228M000
B437*1A5278M000
B437*1B5278M000
B437*1A5338M000
B437*1A5398M000
B437*1B5398M000
B437*1A5478M000
B437*1B5478M000
B437*1A5568M000
B437*1A5688M000
B437*1A5828M000
B437*1A5109M000
Composition of ordering code
* = Mounting style
0 = for capacitors with ring clip/clamp mounting
2 = for capacitors with threaded stud
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 17
B43701, B43721
Standard 85 °C
Useful life1)
For useful life calculations, please use our web-based "AlCap Useful Life Calculation Tool", which
can be found on the Internet under the following link
http://www.epcos.com/designtools/alu_useful_life/Useful_life.swf.
The AlCap Useful Life Calculation Tool provides calculations of useful life as well as additional
data for selected capacitor types under operating conditions defined by the user.
Frequency characteristics of ESR
Typical behavior
Impedance Z versus frequency f
Typical behavior at 20 °C
1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 17
B43701, B43721
Standard 85 °C
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have been optimized both with a view to the intended
application and with regard to health and environmental compatibility. They do not contain any
solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, some of the high-voltage electrolytes used by EPCOS are self-extinguishing.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no alternative materials are currently
known. However, the amount of dangerous materials used in our products is limited to an
absolute minimum.
Materials and chemicals used in EPCOS aluminum electrolytic capacitors are continuously
adapted in compliance with the EPCOS Corporate Environmental Policy and the latest EU
regulations and guidelines such as RoHS, REACH/SVHC, GADSL, and ELV.
MDS (Material Data Sheets) are available on the EPCOS website for all types listed in the data
book. MDS for customer specific capacitors are available upon request.
MSDS (Material Safety Data Sheets) are available for all of our electrolytes upon request.
Nevertheless, the following rules should be observed when handling aluminum electrolytic
capacitors: No electrolyte should come into contact with eyes or skin. If electrolyte does come
into contact with the skin, wash the affected areas immediately with running water. If the eyes are
affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical
treatment. Avoid inhaling electrolyte vapor or mists. Workplaces and other affected areas should
be well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 17
B43701, B43721
Standard 85 °C
Product safety
The table below summarizes the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Polarity
Reverse voltage
Mounting
position of screwterminal capacitors
Robustness of
terminals
Mounting of
single-ended
capacitors
Soldering
Soldering,
cleaning agents
Upper category
temperature
Passive
flammability
Safety information
Reference
chapter "General
technical information"
Make sure that polar capacitors are connected
1
with the right polarity.
"Basic construction of
aluminum electrolytic
capacitors"
Voltages of opposite polarity should be prevented 3.1.6
by connecting a diode.
"Reverse voltage"
Screw terminal capacitors must not be mounted
11.1.
with terminals facing down unless otherwise
"Mounting positions of
specified.
capacitors with screw
terminals"
The following maximum tightening torques must
11.3
not be exceeded when connecting screw
"Mounting torques"
terminals:
M5: 2.5 Nm
M6: 4.0 Nm
The internal structure of single-ended capacitors 11.4
might be damaged if excessive force is applied to "Mounting
the lead wires.
considerations for
Avoid any compressive, tensile or flexural stress. single-ended capacitors"
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
Do not exceed the specified time or temperature 11.5
limits during soldering.
"Soldering"
Do not allow halogenated hydrocarbons to come 11.6
into contact with aluminum electrolytic capacitors. "Cleaning agents"
Do not exceed the upper category temperature.
7.2
"Maximum permissible
operating temperature"
Avoid external energy, e.g. fire.
8.1
"Passive flammability"
Please read Cautions and warnings and
Important notes at the end of this document.
Page 12 of 17
B43701, B43721
Standard 85 °C
Topic
Safety information
Active
flammability
Maintenance
Avoid overload of the capacitors.
Storage
Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply excessive mechanical stress to the
capacitor terminals when mounting.
Do not store capacitors at high temperatures or
high humidity. Capacitors should be stored at
+5 to +35 °C and a relative humidity of ≤ 75%.
Breakdown strength Do not damage the insulating sleeve, especially
of insulating
when ring clips are used for mounting.
sleeves
Reference
chapter "General
technical information"
8.2
"Active flammability"
10
"Maintenance"
7.3
"Shelf life and storage
conditions"
Reference
chapter "Capacitors with
screw terminals"
"Screw terminals accessories"
Display of ordering codes for EPCOS products
The ordering code for one and the same product can be represented differently in data sheets,
data books, other publications and the website of EPCOS, or in order-related documents such as
shipping notes, order confirmations and product labels. The varying representations of the
ordering codes are due to different processes employed and do not affect the specifications of the
respective products. Detailed information can be found on the Internet under
www.epcos.com/orderingcodes.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 17
B43701, B43721
Standard 85 °C
Symbols and terms
Symbol
English
German
C
CR
CS
CS,T
Cf
d
dmax
ESL
ESR
ESRf
Capacitance
Rated capacitance
Series capacitance
Series capacitance at temperature T
Capacitance at frequency f
Case diameter, nominal dimension
Maximum case diameter
Self-inductance
Equivalent series resistance
Equivalent series resistance at
frequency f
Equivalent series resistance at
temperature T
Frequency
Current
Alternating current (ripple current)
Root-mean-square value of alternating
current
Ripple current at frequency f
Maximum permissible ripple current
Rated ripple current
Leakage current
Operating leakage current
Case length, nominal dimension
Maximum case length (without
terminals and mounting stud)
Resistance
Insulation resistance
Balancing resistance
Temperature
Temperature difference
Ambient temperature
Case temperature
Capacitor base temperature
Time
Period
Service life (operating hours)
Kapazität
Nennkapazität
Serienkapazität
Serienkapazität bei Temperatur T
Kapazität bei Frequenz f
Gehäusedurchmesser, Nennmaß
Maximaler Gehäusedurchmesser
Eigeninduktivität
Ersatzserienwiderstand
Ersatzserienwiderstand bei Frequenz f
ESRT
f
I
IAC
IAC,RMS
IAC,f
IAC,max
IAC,R
Ileak
Ileak,op
l
lmax
R
Rins
Rsymm
T
∆T
TA
TC
TB
t
∆t
tb
Please read Cautions and warnings and
Important notes at the end of this document.
Ersatzserienwiderstand bei Temperatur T
Frequenz
Strom
Wechselstrom
Wechselstrom, Effektivwert
Wechselstrom bei Frequenz f
Maximal zulässiger Wechselstrom
Nennwechselstrom
Reststrom
Betriebsreststrom
Gehäuselänge, Nennmaß
Maximale Gehäuselänge (ohne Anschlüsse
und Gewindebolzen)
Widerstand
Isolationswiderstand
Symmetrierwiderstand
Temperatur
Temperaturdifferenz
Umgebungstemperatur
Gehäusetemperatur
Temperatur des Gehäusebodens
Zeit
Zeitraum
Brauchbarkeitsdauer (Betriebszeit)
Page 14 of 17
B43701, B43721
Standard 85 °C
Symbol
V
VF
Vop
VR
VS
XC
XL
Z
ZT
tan δ
λ
ε0
εr
ω
English
Voltage
Forming voltage
Operating voltage
Rated voltage, DC voltage
Surge voltage
Capacitive reactance
Inductive reactance
Impedance
Impedance at temperature T
Dissipation factor
Failure rate
Absolute permittivity
Relative permittivity
Angular velocity; 2 π f
German
Spannung
Formierspannung
Betriebsspannung
Nennspannung, Gleichspannung
Spitzenspannung
Kapazitiver Blindwiderstand
Induktiver Blindwiderstand
Scheinwiderstand
Scheinwiderstand bei Temperatur T
Verlustfaktor
Ausfallrate
Elektrische Feldkonstante
Dielektrizitätszahl
Kreisfrequenz; 2 π f
Note
All dimensions are given in mm.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 17
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association
(ZVEI).
Page 16 of 17
Important notes
7. The trade names EPCOS, Alu-X, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CSSP,
CTVS, DeltaCap, DigiSiMic, DSSP, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue,
MiniCell, MKD, MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PQSine,
SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D,
SIP5K, TFAP, ThermoFuse, WindCap are trademarks registered or pending in Europe and
in other countries. Further information will be found on the Internet at
www.epcos.com/trademarks.
Page 17 of 17
Similar pages