austriamicrosystems AG is now ams AG The technical content of this austriamicrosystems datasheet is still valid. Contact information: Headquarters: ams AG Tobelbaderstrasse 30 8141 Unterpremstaetten, Austria Tel: +43 (0) 3136 500 0 e-Mail: [email protected] Please visit our website at www.ams.com Datasheet AS13985 Micropower 150mA Low-Noise LDO 2 Key Features Stability is guaranteed with a ceramic output capacitor from 1 to 22µF. The low equivalent series resistance of these capacitors ensures low output impedance at high frequencies. Ultra-Low Dropout Voltage (typically 45mV @ 150mA, 0.3mV @ 1mA) ! Supply Range: 2.5V to 5.5V ! Output Voltage Range: 1.2V to 5.0V (in 25mV Steps) ! Output Current: 150mA (Guaranteed) ! Stable with Low-ESR Output Capacitor ! Integrated Over-Temperature/Over-Current Protection ! Low GND Pin Current (only 95µA) am lc s on A te G nt st il Automatic sleep mode requires less than 1µA quiescent current when pin EN is pulled low. ! al id The AS13985 is a high-performance low-dropout 150mA voltage regulator designed for use with very-low ESR output capacitors. The device can deliver superior performance in all specifications critical to battery-powered designs, and is perfectly suited for mobile phones, PDAs, MP3 players, and other battery powered devices. lv 1 General Description Regulation performance is excellent even under low dropout conditions, when the power transistor has to operate in linear mode. A 10nF bypass capacitor can be added to reduce output noise to 30µV. The low-noise performance allows direct connection of noise sensitive circuits without additional filtering networks. Multiple output voltage options are available as standard products. Contact austriamicrosystems AG for details. ! Output Voltage Accuracy: 1% ! Minimal External Components Required ! High Peak-Current Capability ! Low Shutdown Current: ≤1µA ! Operating Temperature Junction Range: -40 to +125°C ! Smallest Available Packages: - 5-bump WLP - 5-pin SOT23 The AS13985 is available in a 5-bump WLP package and a 5-pin SOT23 package. 3 Applications The AS13985 is ideal for powering cordless and mobile phones, MP3 players, CD and DVD players, PDAs, handheld computers, digital cameras, and any other hand-held battery-powered device. ni ca Figure 1. AS13985 - Block Diagram VIN Te ch EN VREF – + VOUT Over-Current/ Over-Temperature Protection BYPASS GND www.austriamicrosystems.com AS13985 Revision 1.13 1 - 12 AS13985 Datasheet - P i n o u t 4 Pinout 4.1 Pin Assignments Figure 2. Pin Assignments (Top View) 5 VOUT al id VIN 1 5 4 2 GND 2 AS13985 (SOT23) AS13985 (WLP; Top Through View) lv 3 1 4 EN am lc s on A te G nt st il BYPASS 3 4.2 Pin Descriptions Table 1. Pin Descriptions Name VIN GND BYPASS EN SOT23 Description 4 1 Input Voltage 2 2 Ground 5 3 Low-Noise Operation Bypass Capacitor 1 4 Logic-High Enable Input. VEN ≥ 1.2V: VOUT is enabled. VEN ≤ 0.4V: VOUT is disabled. 3 5 Regulated Output Voltage Te ch ni ca VOUT WLP www.austriamicrosystems.com Revision 1.13 2 - 12 AS13985 Datasheet - A b s o l u t e M a x i m u m R a t i n g s 5 Absolute Maximum Ratings Stresses beyond those listed in Table 2 may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in Section 6 Electrical Characteristics on page 4 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Min Max Units -0.3 +7 V Input Supply Voltage (Operating) +2.5 +5.5 V Shutdown Input Voltage (Survival) -0.3 +7 V Output Voltage (Survival) -0.3 +7 V Comments lv Parameter Input Supply Voltage (Survival) al id Table 2. Absolute Maximum Ratings IOUT (Survival) Short-circuit protected. Input/Output Voltage (Survival) 1 -0.3 +7 V 2 Internally limited. am lc s on A te G nt st il Power Dissipation Operating Junction Temperature -40 +125 ºC Storage Temperature Range -65 +150 ºC Package Body Temperature +260 ºC The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/ JEDEC J-STD-020D “Moisture/Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices”. The lead finish for Pb-free leaded packages is matte tin (100% Sn). 1. The output PNP structure contains a diode between pins VIN and VOUT that is normally reverse-biased. reversing the polarity of pins VIN and VOUT will activate this diode. 2. The maximum allowable power dissipation is a function of the maximum junction temperature (TJ(MAX), the junction-to-ambient thermal resistance (ΘJA), and the ambient temperature (TAMB). The maximum allowable power dissipation at any ambient temperature is calculated as: P(MAX) = (TJ(MAX) - (TAMB))/ΘJA Where: (EQ 1) ca The value of ΘJA for the SOT23 package is 220ºC/W in a typical PC-board mounting. The value of ΘJA for the WLP package is 225ºC/W. Te ch ni Note: Exceeding the maximum allowable dissipation will cause excessive device temperature and the regulator will go into thermal shutdown. www.austriamicrosystems.com Revision 1.13 3 - 12 AS13985 Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s 6 Electrical Characteristics TAMB = 25ºC, VIN = VOUT(NOM) +0.5V, COUT = CIN = 1µF, CBYPASS = 10nF, IOUT = 1mA, VEN = 1.4V (unless otherwise specified) Caution: Exposing the WLP package to direct light could cause device malfunction. Table 3. Electrical Characteristics VIN Operating Input Voltage VOUT(NOM) - VOUT Conditions Min IOUT = 1mA TAMB = -40 to 125ºC -75 75 IOUT = 1mA -1 1 TAMB= -40 to 125ºC -2 2 VIN = (VOUT(NOM) + 0.5V) to 4.5V, VOUT < 3V -0.15 VIN = (VOUT(NOM) + 0.5V) to 5.5V, VOUT < 3V -0.3 Output Voltage Accuracy < 2.5V VOUT Output Voltage Accuracy ≥ 2.5V VOUT Max Unit 2.5 5.5 V -50 50 ΔVOUT Load Regulation Output AC Line Regulation %/V 0.3 IOUT = 1 to 150mA, VOUT < 2.5V, TAMB = -40 to 125ºC 0.002 IOUT = 1 to 150mA, VOUT ≥ 2.5V, TAMB = -40 to 125ºC (for WLP) 0.0004 0.002 IOUT = 1 to 150mA, TAMB = -40 to 125ºC (for SOT23-5), VOUT ≥ 2.5V 0.0025 0.005 VIN = VOUT(NOM) + 1V, IOUT = 150mA, tR = tF = 30µs 1 On Mode: VEN = 1.2V, IOUT = 0mA 95 Quiescent Current 250 0.003 Off Mode: VEN = 0.4V, TAMB= -40 to 125ºC, IOUT = 0mA IOUT = 1mA ca ch ni 3 Te Short Circuit Current SVR IOUT(PK) VEN Supply Voltage Rejection Peak Output Current Enable Input Logic High www.austriamicrosystems.com 2 15 35 IOUT = 100mA mV 30 IOUT = 100mA, TAMB = -40 to 125ºC 70 IOUT = 150mA 45 IOUT = 150mA, TAMB = -40 to 125ºC 100 RLOAD = 0Ω 500 VIN = VOUT(NOM) + 1V, VRIPPLE = 50mV, IOUT = 50mA, f = 1kHz 60 VIN = VOUT(NOM) + 1V, VRIPPLE = 50mV, IOUT = 50mA, f= 10kHz 55 mA dB VOUT ≥ VOUT(NOM) - 5% Revision 1.13 µA 2 2 IOUT = 50mA, TAMB = -40 to 125ºC VIN = 2.5 to 5.5V, TAMB = -40 to 125ºC 2 0.3 IOUT = 50mA Enable Input Logic Low mVPP 1 IOUT = 1mA, TAMB = -40 to 125ºC Dropout Voltage %/mA 160 On Mode: VEN = 1.2V, IOUT = 0 to 150mA, TAMB = -40 to 125ºC Off Mode: VEN = 0.4V, IOUT = 0mA VDROP 0.008 130 On Mode: VEN = 1.2V, IOUT = 0 to 150mA ISC % of VOUT(NOM) 0.15 On Mode: VEN = 1.2V, IOUT = 0mA, TAMB = -40 to 125ºC IQ mV am lc s on A te G nt st il Line Regulation 1 Typ al id Parameter lv Symbol 300 500 mA 0.4 4 1.2 V 4 - 12 AS13985 Datasheet - E l e c t r i c a l C h a r a c t e r i s t i c s Table 3. Electrical Characteristics Conditions Parameter Min Typ IEN Enable Input Current VEN = 0.4V, VIN = 5.5V eN Output Noise Voltage BW = 10Hz to 100kHz, COUT = 1µF, IOUT = 0mA 30 CBYPASS = 10nF 150 tON Turn On Time 5 ±1 Thermal Shutdown 4, 6 Threshold Recommended Output Capacitor TSHDN 160 Output Capacitor Unit nA µVRMS 250 µs ºC 2 Capacitance 1 22 ESR 5 5000 µF mΩ lv COUT Max 2 al id Symbol am lc s on A te G nt st il 1. Temperature variations are included within the output voltage accuracy. 2. Guaranteed by design. 3. Dropout voltage is the input-to-output voltage difference at which the output voltage is 100mV below its nominal value (does not apply to input voltages below 2.5V). 4. EN must be driven with a tR = tF < 10ms. 5. Turn on time is time measured between the enable input just exceeding the VEN high value and the output voltage just reaching 95% of its nominal value. 6. Typical thermal protection hysteresis is 20ºC. Note: All limits are guaranteed. The parameters with min and max values are guaranteed with production tests or SQC (Statistical Quality Control) methods. Figure 3. AC Line Regulation Input Voltage Test Signal 30µs 30µs 600mV VIN = VOUT(NOM) + 1V ca 600µs 4.6ms Te ch ni Figure 4. SVR Input Voltage Test Signal www.austriamicrosystems.com VIN 50mV VOUT(NOM) + 1V Revision 1.13 5 - 12 AS13985 Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s 7 Typical Operating Characteristics TAMB = +25ºC (unless otherwise specified) Figure 5. Output Voltage vs. Temperature; VIN = 3.4V, VSHDN = 1.4V, IOUT = 1mA Figure 6. Shutdown Voltage vs. Temperature; VOUT = 2.9V, IOUT = 10mA 3 1 2.925 2.9 2.875 2.85 0.9 VIN = 5.5V 0.8 VIN = 3.8V 0.7 2.825 -20 5 0.6 -45 am lc s on A te G nt st il 2.8 -45 30 55 80 105 130 -20 Temperature (°C) 5 30 55 80 105 130 Temperature (°C) Figure 7. Load Regulation vs. Temperature; VIN = 3.4V, VSHDN = 1.4V, IOUT = 1 to 150mA Figure 8. Line Regulation vs. Temperature; VIN = 3.4 to 5.0V, VSHDN =1.4V, IOUT =1mA 0.5 0.0075 0.4 0.005 0.3 0.0025 Line (%/V) . Load (%/mA) . al id 2.95 lv Shutdown Voltage (V) . Output Voltage (V) . 2.975 0 -0.0025 0.2 0.1 0 -0.1 -0.005 -0.2 -0.0075 -45 -20 5 30 55 -0.3 -45 80 105 130 -20 ca Temperature (°C) Figure 9. SVR vs. Frequency; VIN = 3.9 to 3.95V, VOUT = 2.9V, IOUT = 50mA, VSHDN = 1.4V 90 80 105 130 300 70 200 IQ (µA) . 60 50 40 Te SVR (dB) . 55 250 ch 80 30 Figure 10. Quiescent Current vs. Temperature; VOUT = 2.9V, VSHDN = 1.4V ni 100 5 Temperature (°C) 150 VIN = 5.5V 100 30 VIN = 3.4V 20 50 10 0 0.1 2.1 4.1 6.1 8.1 10.1 0 -45 Frequency (kHz) www.austriamicrosystems.com -20 5 30 55 80 105 130 Temperature (°C) Revision 1.13 6 - 12 AS13985 Datasheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s 500mV/Div Figure 12. Turn On Time; VIN = 3.3V, CBYPASS = 10nF, CIN = COUT = 1µF (Ceramic), tR = 20ns, IOUT = 1mA, VOUT = 2.8V 50µs/Div Te ch ni ca am lc s on A te G nt st il 1ms/Div lv EN VOUT 2mV/Div 500mV/Div al id VOUT VIN 1V/Div Figure 11. Line Transient Response; VIN = 3.8 to 4.4V, TJ = 25ºC, IOUT = 150mA, CIN = COUT = 1µF, VOUT = 2.7V CBYPASS = 10nF, Rise Time/Fall Time = 1µs www.austriamicrosystems.com Revision 1.13 7 - 12 AS13985 Datasheet - Ty p i c a l A p p l i c a t i o n 8 Typical Application VIN VIN CIN 1µF EN 1.23V – + lv VREF al id Figure 13. Typical Application Diagram VOUT VOUT am lc s on A te G nt st il Over-Current/ Over-Temperature Protection BYPASS GND CBYPASS 0.01µF AS13985 COUT 1µF Te ch ni ca GND www.austriamicrosystems.com Revision 1.13 8 - 12 AS13985 Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s 9 Package Drawings and Markings The AS13985 is available in a 5-bump WLP package and a 5-pin SOT23 package. Te ch ni ca am lc s on A te G nt st il lv al id Figure 14. 5-bump WLP Package www.austriamicrosystems.com Revision 1.13 9 - 12 AS13985 Datasheet - P a c k a g e D r a w i n g s a n d M a r k i n g s am lc s on A te G nt st il lv al id Figure 15. 5-pin SOT23 Package Notes: 1. All dimensions are in millimeters. 2. Foot length is measured at the intercept point between datum A and lead surface. 3. Package outline exclusive of mold flash and metal burr. 4. Package outline inclusive of solder plating. 5. Complies with EIAJ SC74. Symbol A A1 A2 b C D E E1 L e e1 Te ch ni ca α Min Max 0.90 1.45 0.00 0.15 0.90 1.30 0.30 0.50 0.09 0.20 2.80 3.05 2.60 3.00 1.50 1.75 0.30 0.55 0.95 Ref 1.90 Ref 0º 8º www.austriamicrosystems.com Revision 1.13 10 - 12 AS13985 Datasheet - O r d e r i n g I n f o r m a t i o n 10 Ordering Information The AS13985 is available as the standard versions listed in Table 4. Other versions are available upon request. For more information and inquiries contact http://www.austriamicrosystems.com/contact Table 4. Ordering Information Marking Description Delivery Form Package AS13985F33-T ASKK 3.3V LDO, 150mA Tape and Reel 5-bump WLP AS13985F30-T ASKJ 3.0V LDO, 150mA Tape and Reel 5-bump WLP AS13985F29-T ASKI 2.9V LDO, 150mA Tape and Reel 5-bump WLP AS13985F28-T ASLE 2.8V LDO, 150mA Tape and Reel 5-bump WLP AS13985F27-T ASKL 2.7V LDO, 150mA Tape and Reel 5-bump WLP AS13985F18-T ASKM 1.8V LDO, 150mA Tape and Reel 5-bump WLP AS13985F12-T ASKN 1.2V LDO, 150mA Tape and Reel 5-bump WLP AS13985H33-T ASK0 3.3V LDO, 150mA Tape and Reel 5-pin SOT23 ASK1 3.0V LDO, 150mA Tape and Reel 5-pin SOT23 ASK2 2.9V LDO, 150mA Tape and Reel 5-pin SOT23 ASLF 2.8V LDO, 150mA Tape and Reel 5-pin SOT23 ASK3 2.7V LDO, 150mA Tape and Reel 5-pin SOT23 ASK4 1.8V LDO, 150mA Tape and Reel 5-pin SOT23 ASK5 1.2V LDO, 150mA Tape and Reel 5-pin SOT23 AS13985H29-T AS13985H28-T AS13985H27-T AS13985H18-T AS13985H12-T lv am lc s on A te G nt st il AS13985H30-T al id Ordering Code Note: All products are RoHS compliant and Pb-free. Buy our products or get free samples online at ICdirect: http://www.austriamicrosystems.com/ICdirect Te ch ni ca For further information and requests, please contact us mailto:[email protected] or find your local distributor at http://www.austriamicrosystems.com/distributor www.austriamicrosystems.com Revision 1.13 11 - 12 AS13985 Datasheet Copyrights Copyright © 1997-2009, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. al id Disclaimer am lc s on A te G nt st il lv Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. ca The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. ni Contact Information Headquarters ch austriamicrosystems AG Tobelbaderstrasse 30 A-8141 Unterpremstaetten, Austria Te Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com Revision 1.13 12 - 12