AM5TW-N Series DC-DC CONVERTERS Picture Available Soon 5 watt dc-dc converters • 24 PIN DIP PACKAGE • INPUT/OUTPUT ISOLATION OF 1500VDC • WIDE 4:1 INPUT RANGE • OPERATING TEMPERATURE: -40°C ... +71°C • HIGH EFFICIENCY UP TO 85% • CONTINUOUS SHORT CIRCUIT PROTECTION • SHIELDED METAL PACKAGE • PIN-COMPATIBLE WITH MULTIPLE MANUFACTURERS GENERAL DESCRIPTION Our AM5TW-N series is a family of cost effective 5W single and dual output DC/DC converters. These converters combine a shielded metal package in a 24-pin DIP compatible case and includes high performance features such as a 1500VDC input/output isolation voltage, continuous short circuit protection and a tight line / load regulation. Wide range devices operate over a 4:1 input voltage range continuously providing a stable output voltage. 18 models operate from input voltages of 24 and 48VDC with output voltages of 3.3, 5, 12, 15, 24, ±5, ±12, ±15 & ±24VDC. High performance features include high efficiency operation up to 85% and output voltage accuracy of ±1%. All models are packaged in a low profile 31.75 x 20.32 x 10.16mm case. Operation is specified over the full operating temperature range of -40°C to +71°C with no derating required. Cooling is by free-air convection. ELECTRICAL SPECIFICATIONS All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. Input Specifications: Voltage range Filter Isolation Specifications: Rated voltage (60 sec) Resistance Capacitance 24VDC, 9~36VDC 48VDC, 18~72VDC p (Pi) Network 1500VDC > 1000MOhm 80pF, typ. Environmental Specifications: Operating temperature (ambient) -40°C ... +71°C Storage temperature -55°C ... +125°C Case Temperature +100°C, max. Derating None required Humidity (non-condensing) Up to 95% Cooling Free-air Convection General Specifications: Efficiency Switching frequency (Single) Switching frequency (Dual) Output Specifications: Voltage accuracy (Single) Voltage accuracy (Dual) Ripple Noise (at 20MHz BW) Short circuit protection Line voltage regulation Load voltage regulation Temperature coefficient Physical Specifications: Dimensions Weight Case material 75% to 85% 300KHz, typ., 100% load 250KHz, typ., 100% load ±1%, typ. ±1% p. & ±3% n., typ. 30m Vp-p, typ. 100mVp-p, typ. Continuous ±0.2%, max. ±0.5%, max. ±0.02%/°C, typ. 31.75x20.32x10.16mm 1.25x0.80x0.40inches 26g Metal MTBF: > 1,000,000 hrs (MIL-HDBK-217F, Ground Benign, t=+25°C) Specifications are subject to change without notification. Continued on next page TO ORDER CALL 1-888-9-AIMTEC AM5TW-N Series MODELS Single Output AM5TW-2403S-N AM5TW-2405S-N AM5TW-2412S-N AM5TW-2415S-N AM5TW-2424S-N AM5TW-4803S-N AM5TW-4805S-N AM5TW-4812S-N AM5TW-4815S-N AM5TW-4824S-N Input Voltage 9 - 36VDC 18 - 72VDC Output Voltage Max. Output Current 3.3VDC 5VDC 12VDC 15VDC 24VDC 3.3VDC 5VDC 12VDC 15VDC 24VDC 1200mA 1000mA 420mA 330mA 200mA 1200mA 1000mA 420mA 330mA 200mA MODELS Dual Output Models AM5TW-2405D-N AM5TW-2412D-N AM5TW-2415D-N AM5TW-2424D-N AM5TW-4805D-N AM5TW-4812D-N AM5TW-4815D-N AM5TW-4824D-N Input Voltage 9 - 36VDC 18 - 72VDC Output Voltage Max. Output Current ±5VDC ±12VDC ±15VDC ±24VDC ±5VDC ±12VDC ±15VDC ±24VDC ±500mA ±210mA ±165mA ±100mA ±500mA ±210mA ±165mA ±100mA OUTLINE DIMENSIONS & PIN CONNECTIONS Note: All Pins on a 2.54mm pitch; All Pin diameters are 0.50 mm (Tolerance:±0.25); All dimensions in mm. Pin Single Dual 1 2 3 9 10 11 12/13 14 15 16 22 23 24 Omitted -V Input -V Input Omitted Omitted N.C. Omitted +V Output Omitted -V Output +V Input +V Input Omitted Omitted -V Input -V Input Common Omitted -V Output Omitted +V Output Omitted Common +V Input +V Input Omitted Continued on next page TO ORDER CALL 1-888-9-AIMTEC DC-DC CONVERTERS Models AM5TW-N Series DC-DC CONVERTERS TYPICAL CHARACTERISTICS APPLICATION NOTE Recommended Circuit All of our AM5TW-N Series have been tested according to the following recommended testing circuit before leaving our factory. This series should be tested under load & never be tested under no load (See Figure 1). Figure 1 - Single Output If you want to further decrease the input/output ripple, you can increase capacitance properly or choose capacitors with a low ESR. However, the capacitance should not be too high.(See table 1). Input Current When it is used in an unregulated power supply, be sure that the fluctuating range of the power supply and the rippled voltage do not exceed the module standard. Input current of power supply should afford the startup current of this kind of DC/DC module. (See figure 2) Figure 1 - Dual Output External Capacitor Although this series of DC/DC converters can work without an external capacitor, it is highly recommended to use one in order to keep an optimum performance. (See Table 1) Requirement on Output Load To ensure this module operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load (namely full load). During operation, make sure the specified range of input voltage is not exceeded, the minimum out put load is not less than 10% Of the full load, and that this product should never be operated under no load!!! If the actual load is less below the specified minimum load, the output ripple of this type of DC/DC converter will increase drastically and at the same time efficiency & reliability of the circuit will decrease deeply .If the actual output power from the load in your circuit is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, or use our company’s other products with a lower rated output power. Figure 2 - Single & Dual Outputs External Capacitor Table Single & Dual Outputs Vin Cin Vout 24V 100uF 5V 48V 100uF 12V - - 15V - - 24V Cout 100uF each 1A Current TO ORDER CALL 1-888-9-AIMTEC