ZETTLER AT-240160BFIQY-52H-A Specifications for lcd module Datasheet

A MP I R E
SPECIFICATIONS FOR
LCD MODULE
CUSTOMER
CUSTOMER PART NO.
AMPIRE PART NO.
APPROVED
AT-240160BFIQY-52H-A
BY
DATE
† Approved For Specifications
† Approved For Specifications & Sample
APPROVED BY
Date : 2005/1/26
CHECKED BY
ORGANIZED BY
AMPIRE CO., LTD.
1
RECORD
OF REVISION
Revision Date
Section
Contents
Editor
2005/1/26
-
New Release
Kokai
Date : 2005/1/26
AMPIRE CO., LTD.
2
1
FEATURES
(1) Display format : 240 × 160 dot-matrix
(2) Construction : LCD , TAB IC, Yellow-green edge LED backlight, Bazel and PCB.
(3) Display type : FSTN, Transflective , 6 o’clock view.
(4) Controller : SED1335F0B ; 32K SRAM.
(5) 5V single power input. Built-in DC/DC converter for LCD driving.
(6) Built-in Temperature compensation circuit.
(7) Extended temperature type.
(8) Landscape or Portrait Display Type Selectable by Jumper Setting (Default : Landscape)
(9) 80 or 68 Family MPU Selectable by Jumper Setting
2
3
MECHANICAL DATA
Parameter
Stand Value
Unit
Dot size
0.225(W) × 0.225(H)
mm
Dot pitch
0.24(W) × 0.24(H)
mm
Viewing area
67.6(W) × 47.5(H)
mm
Module size
74.6(W) × 55.9(H) × 8.7 max (T)
mm
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Min
Max
Unit
Logic Circuit Supply Voltage
VDD-VSS
-0.3
7.0
V
LCD Driving Voltage
VADJ-VSS
-0.3
26.0
V
Input Voltage
VI
-0.3
VDD+0.3
V
Operating Temp.
TOP
-20
70
°C
Storage Temp.
TSTG
-30
80
°C
Extended temp. type
Date : 2005/1/26
AMPIRE CO., LTD.
3
4
ELECTRO-OPTICAL CHARACTERISTICS
Parameter
Symbol
Condition
Min
Typ
Max
Unit
V
Note
----- Electronic Characteristics ----Logic Circuit
Supply Voltage
--
4.5
5
5.5
-20°C
20.0
21.1
22.3
25°C
17.81
18.8
19.8
70°C
14.9
15.7
16.6
VIH
--
0.8 VDD
--
VDD
V
VIL
--
VSS
--
0.2 VDD
V
Logic Supply
Current
IDD
VDD = 5V
--
40
--
mA
Supply Current for
LED backlight
ILED
LEDA = 5V
--
100
--
mA
LCD Driving
Voltage
Input Voltage
VDD-VSS
V5-VSS
V
----- Optical Characteristics ----Contrast
CR
25°C
2
5
Rise Time
Tr
25°C
--
160
240
ms
Fall Time
Tf
25°C
--
320
480
ms
θf
25°C &
25
--
--
θb
CR≥2
40
--
--
θl
35
--
--
θr
25
--
--
--
64
--
Viewing Angle
Range
Frame Frequency
fF
25°C
Note 1
Deg.
Note 2
Note 3
Hz
----- LED Back-light Characteristics ----Forward Voltage
VF
--
--
3.9
4.0
V
Forward Current
IF
VF=3.9V
--
50
--
mA
VF=3.9V
--
8
--
cd/m2
LCM Luminous intensity
Date : 2005/1/26
Supply Voltage
between A&K
AMPIRE CO., LTD.
4
A
K
* LED Dice number = 2x5=10
240160BL Yellow-green LED
LED Driving Circuit:
(NOTE 1) Contrast ratio :
CR = (Brightness in OFF state) / (Brightness in ON state)
Date : 2005/1/26
AMPIRE CO., LTD.
5
( NOTE 2 ) Response time :
(NOTE 3) Viewing angle
Date : 2005/1/26
AMPIRE CO., LTD.
6
5
BLOCK DIAGRAM
From
MPU
/RESET
/RD
/WR Controller
/CS SED1335
A0
DB0~7
FLM
LP, M, /DISPOFF
LCD Panel
COM.
Driver
160
240 x 160 Dots
240
SRAM
LED_ON
6
SEG.
Driver
CP,D0~D3
LED Backlight
POWER SUPPLY CIRCUIT
21.4V
VDD
VLCD
VADJ
DC/DC
Converter
Bias &
LCD Bias
Temperature
Circuit
compensation
circuit
VSS
Date : 2005/1/26
AMPIRE CO., LTD.
7
7
INTERFACE DEFINITION
CN1: Interface of pure driver ( * No Use in this LCM)
PIN NO.
SIGNAL
LEVEL
1~20
NC
-
FUNCTION
No Connection
CN2: LCM with Built-In Controller
PIN NO.
SIGNAL
LEVEL
FUNCTION
1
/RESET
H/L
2
/RD
H/L
3
/WR
H/L
4
/CS
H/L
Reset Signal
80 Series: Read Signal
68 Series: Enable Signal(E)
80 Series: Write Signal
68 Series: R/W Signal
Chip Select Signal
5
A0
H/L
Data Type Selection
6 ~ 13
DB0~DB7
H/L
Data Input(8 bits)
14
VDD
-
Power Supply for Logic(+5.0V)
15
VSS
-
Power Supply(Ground : 0V)
16
VLCD
-
17
VADJ
18
LED_ON
H/L
Positive voltage output (+21.4V)
Contrast Adjustment Input
( VADJ-VSS = LCD driving voltage )
LED On/Off Signal; H: LED On L: LED Off
19
NC
--
No connection
20
NC
--
No connection
CN3:Inter-connection of Touch Panel
PIN NO.
SIGNAL
LEVEL
1~4
NC
-
Date : 2005/1/26
FUNCTION
No Connection
AMPIRE CO., LTD.
8
8
TIMING CHARACTERISTICS
8.1
8080 Family Interface Timing
Parameter
Condition
Symbol
Min Max
Address Hold Time
tAH8
10
Address Setup Time
tAW8
0
System Cycle Time
tCYC
Note
Strobe Pulse Width
CL=100 pF
tOC
150
VDD=2.7~4.5
Data Setup Time
tDS8
120
Data Hold Time
tDH8
5
/RD Access Time
tACC8
80
Output Disable Time
tOH8
10
55
Note: For memory control and system control commands:
tCYC8=2tC+tOC+tCEA+75 > tACV +245
For all other commands:
tCYC8=4tC+tOC+30
Unit
ns
ns
ns
ns
ns
ns
ns
ns
Remark
A0,/CS
/WR,/RD
DB0~DB7
A0,/CS
/WR,/RD
DB0~DB7
(Write)
DB0~DB7
(Read)
Date : 2005/1/26
AMPIRE CO., LTD.
9
8.2
6800 Family Interface Timing
Parameter
Condition
Symbol
Min Max
System Cycle Time
tCYC6
Note
Address Setup Time
tAW6
10
Address Hold Time
tAH6
0
Data Setup Time
CL=100 pF
tDS6
120
VDD=2.7~4.5
Data Hold Time
tDH6
0
Output Disable Time
tOH6
10
75
Access Time
tACC6
130
Enable Pulsewidth
tEW
150
Note: For memory control and system control commands:
tCYC6=2tC+tEW+tCEA+75 > tACV +245
For all other commands:
tCYC6=4tC+tEW+30
Unit
ns
ns
ns
ns
ns
ns
ns
ns
Remark
A0,/CS,
R/W
DB0~DB7
E
E
R/W
A0, /CS
DB0~DB7
(Write)
DB0~DB7
(Read)
AC Electrical Characteristics
Date : 2005/1/26
AMPIRE CO., LTD.
10
9
INSTRUCTION SET
Code
Class
Command
Hex
/RD /WR A0
SYSTEM
System SET
Control
SLEEP IN
D7
D6
D5
D4
D3
D2
D1
D0
1
0
1
0
1
0
0
0
0
0
0
40 Initialized Device and display
8
8.2.1
1
0
1
0
1
0
1
0
0
1
1
53 Enter Standby mode
0
8.2.2
DISP
ON/OFF
1
0
1
0
1
0
1
1
0
0
D
1
8.3.1
SCROLL
1
0
1
0
1
0
0
0
1
0
0
10
8.3.2
CSRFORM
1
0
1
0
1
0
1
1
1
0
1
2
8.3.3
2
8.3.6
0
8.3.4
CGRAM
Display
ADDR.
Control
1
0
1
0
1
0
1
1
1
CSRDIR
1
0
1
0
1
0
0
1
1
HDOT SCR
1
0
1
0
1
0
1
1
OVLAY
1
0
1
0
1
0
1
1
CSRW
1
0
1
0
1
0
0
CSRR
1
0
1
0
1
0
MWRITE
1
0
1
0
1
MREAD
1
0
1
0
1
Drawing
Control
Memory
Control
Command Description
Command read
parameters
Number of
Section
byters
0
0
CD CD
1
0
58, Enable and disable display and
59 display flashing
set Display start address and
44
display regions
5D Set cursor byte
Set start address of character
5C
generator RAM
4C
Set direction of cursor
to
movement
4F
1
0
5A set horizontal scroll position
1
8.3.7
0
1
1
5B set display overlay format
1
8.3.5
0
1
1
0
46 set cursor address
2
8.4.1
0
0
1
1
1
47 read cursor address
2
8.4.2
0
0
0
0
1
0
42 write to display memory
-
8.5.1
0
0
0
0
1
1
43 read from display memory
-
8.5.2
Note:
1. In general, the internal registers of the SED1335F are modified as each command
parameter is input. However, the microprocessor does not have to set all the parameters of
a command and may send a new command before all parameters have been input. The
internal registers for the parameters that have been input will have been changed but the
remaining parameter registers are unchanged.
2 bytes parameters( where two bytes are treated as 1 data item) are handled as following:
a. CSRW, CSRR: Each byte is processed individually. The microprocessor may read or
write just the low byte of the cursor address.
b. SYSTEM SET, SCROLL, CGRAM ADR. : Both parameter bytes are processed together.
If the command is changed after half of the parameter has been input, the single byte is
ignored.
2. APL and APH are 2-byte parameters, but are treated as two 1-byte parameters.
3. Please refer to SED1335F LCD Controller Data Book for detail.
Date : 2005/1/26
AMPIRE CO., LTD.
1
1
10 INNER DATA FORMAT
SEG1
SEG240
#1
D7 D6 D5 D4 D3 D2 D1 D0
-
D7 D6 D5 D4 D3 D2 D1 D0
#2
D7 D6 D5 D4 D3 D2 D1 D0
-
D7 D6 D5 D4 D3 D2 D1 D0
#160 D7 D6 D5 D4 D3 D2 D1 D0
-
D7 D6 D5 D4 D3 D2 D1 D0
Landscape Display Type(Top View)
COM1
#1
#2
#240
COM160
D7
D7
D7
D6
D6
D6
D5
D5
D5
D4
D4
D4
D3
D3
D3
D2
D2
D2
D1
D1
D1
D0
D0
D0
D2
D2
D2
D1
D1
D1
D0
D0
D0
Portrait Display Type (Top View)
Date : 2005/1/26
AMPIRE CO., LTD.
12
11 JUMPER SETTING
Item
Option
Jumper Setting
Display Type
Landscape (default)
Pin 1,2 short on JP1&JP2
Portrait
Pin 2,3 short on JP1&JP2
80 family (default)
Pin 1,2 short on JP3
68 family
Pin 2,3 short on JP3
MPU
Remark
12 QUALITY AND RELIABILITY
12.1 TEST CONDITIONS
Tests should be conducted under the following conditions:
Ambient temperature : 25±5°C
Humidity
: 60±25% RH.
12.2
SAMPLING PLAN
Sampling method shall be in accordance with MIL-STD-105E , level II, normal
single sampling plan .
12.3 ACCEPTABLE QUALITY LEVEL
A major defect is defined as one that could cause failure to or materially reduce the
usability of the unit for its intended purpose. A minor defect is one that does not materially
reduce the usability of the unit for its intended purpose or is an infringement from established
standards and has no significant bearing on its effective use or operation.
12.4 APPEARANCE
An appearance test should be conducted by human sight at approximately 30 cm
distance from the LCD module under flourescent light. The inspection area of LCD panel
shall be within the range of following limits.
Date : 2005/1/26
AMPIRE CO., LTD.
13
12.5 INSPECTION QUALITY CRITERIA
Item
Function
Dimension
Black spots
Black lines
Bubbles in
polarizer
Color
uniformity
Glass
Scratches
Viewing
angle
Contrast
ratio
Response
time
Description
of
defects
Class of
Defects
Major
Major
Minor
Acceptable level
(%)
0.65
1.5
2.5
Minor
2.5
Minor
2.5
Minor
2.5
Obvious visible damage.
Minor
2.5
See note 3
Minor
2.5
See note 1
Minor
2.5
See note 2
Minor
2.5
Short circuit or Pattern cut
Deviation from drawings
Ave . dia . D
area A
area B
Disregard
D≦0.2
3
4
0.2<D≦0.3
2
3
0.3<D≦0.4
0.4<D
0
1
Width W, Length L
A
B
disregard
W≦0.03
3
4
0.03<W≦0.05
1
1
0.05<W≦0.07 , L≦3.0
See line criteria
Average diameter D 0.2 < D < 0.5 mm
for N = 4 , D > 0.5 for N = 1
Rainbow color or newton ring.
ZONE A active area
ZONE B viewing area
Date : 2005/1/26
AMPIRE CO., LTD.
14
12.6 RELIABILITY
Test Item
Test Conditions
Normal Temp. type
Extended Temp. type
High Temperature Operation
50±3°C , t=96 hrs
70±3°C , t=96 hrs
Low Temperature Operation
0±3°C , t=96 hrs
-20±3°C , t=96 hrs
High Temperature Storage
70±3°C , t=96 hrs
80±3°C , t=96 hrs
Low Temperature Storage
Temperature Cycle
Note
1,2
1,2
-20±3°C , t=96 hrs
-30±3°C , t=96 hrs
-20°C ~ 25°C ~ 70°C
-30°C ~ 25°C ~ 80°C
30 m in.
5 min. 30 min. 30 min.
5 min. 30 min.
1,2
( 1 cycle )
( 1 cycle )
Total 5 cycle
Total 5 cycle
40 °C, Humidity 90%, 96 hrs
Humidity Test
1,2
Sweep frequency : 10 ~ 55 ~ 10 Hz/1min
Amplitude : 0.75mm
Vibration Test (Packing)
2
Test direction : X.Y.Z/3 axis
Duration : 30min/each axis
Note 1 : Condensation of water is not permitted on the module.
Note 2 : The module should be inspected after 1 hour storage in normal conditions
(15-35°C , 45-65%RH).
Definitions of life end point :
z
Current drain should be smaller than the specific value.
z
Function of the module should be maintained.
z
Appearance and display quality should not have degraded noticeably.
z
Contrast ratio should be greater than 50% of the initial value.
MTBF=100,000 Hours
LCD Life is 300,000 Hours.
LED Life is 100,000 Hours.
IC, R & C Life are 100,000 Hours.
PCB and Bezel are 1,000,000 Hours.
Date : 2005/1/26
AMPIRE CO., LTD.
15
13 HANDLING PRECAUTIONS
(1) An LCD module is a fragile item and should not be subjected to strong mechanical
shocks.
(2) Avoid applying pressure to the module surface. This will distort the glass and cause a
change in colour.
(3) Under no circumstances should the position of the bezel tabs or their shape be modified.
(4) Do not modify the display PCB in either shape or positioning of components.
(5) Do not modify or move location of the zebra or heat seal connectors.
(6) The device should only be soldered to during interfacing. Modification to other areas of
the board should not be carried out.
(7) In the event of LCD breakage and resultant leakage of fluid do not inhale, ingest or make
contact with the skin. If contact is made rinse immediately.
(8) When cleaning the module use a soft damp cloth with a mild solvent, such as Isopropyl or
Ethyl alcohol. The use of water, ketone or aromatic is not permitted.
(9) Prior to initial power up input signals should not be applied.
(10) Protect the module against static electricity and observe appropriate anti-static
precautions.
Date : 2005/1/26
AMPIRE CO., LTD.
16
14 OUTLINE DIMENSION
Date : 2005/1/26
AMPIRE CO., LTD.
17
晶采 光 電 科技
Date : 2005/1/26
AMPIRE CO., LTD.
18
Similar pages