NTC Thermistors (Disc Type) Disc Type NTC Thermistors Type: ERTD Disc type negative temperaturecoefficient thermistors. Resistance values from 8 W to 150 kW and B Values are from 3000 K to5000 K. n Features l Wide selection of temperature coefficients l Excellent electrical and thermal stability n Recommended Applications l Temperature detection l Temperature compensation for measuring instruments l Temperature compensation for deflection coil in TV n Explanation of Part Numbers E R T D Ω ± ± ± For the NTC Thermistor operated in ambient temperature above 25 ûC, power rating should be derated in accordance with the right figure. Rated Load (%) n Derating Curve for the NTC Thermistor Ambient Temperature (˚C) Rev.02/04 NTC Thermistors (Disc Type) n Ratings and Characteristics Part No. Zero-Power Resistance at 25 ¡C(W) B Value]] (K) Maximum Permissible Power(W) Heat Dissipation Constant (mW/¡C) Thermal Time Resistance Constant Ratio (s) R25/R50 Table A/B Curve No. ERTD2FEL]200S 20 3000 2.18 Ñ ERTD2FFL]400S 40 3200 2.30 Ñ ERTD2FGL]750S 75 3700 2.62 1 ] 100 3500 2.48 Ñ ] ERTD2FGL 101S 100 3700 2.62 2 ERTD2FGL]171S 170 3700 2.62 3 ] 250 3500 2.48 Ñ ] 250 3900 2.76 4 ] ERTD2FGL 301S 300 3900 2.76 Ñ ERTD2FFL]351S 350 3500 2.48 5 ] 600 4000 2.83 6 ] 800 3900 2.76 7 ] ERTD2FGL 102S 1000 3700 2.61 Ñ ERTD2FGL]142S 1400 3900 2.76 Ñ ] 2000 4000 2.83 8 ] 3300 4000 2.83 9 ] ERTD2FHL 462S 4600 4100 2.90 Ñ ERTD2FHL]802S 8000 4100 2.90 10 ERTD2FHL]103S ERTD2FFL 101S ERTD2FFL 251S ERTD2FGL 251S ERTD2FGL 601S ERTD2FGL 801S ERTD2FGL 202S ERTD2FGL 332S 0.4 4.5 20 10000 4100 2.90 Ñ ] 15000 4200 2.98 11 ] ERTD2FHL 333S 33000 4500 3.22 12 ERTD2FHL]503S 50000 4500 3.22 13 ERTD2FHL 153S 150000 4800 3.48 14 ] 8 3000 2.18 15 ] ERTD3FFL 130S 13 3200 2.30 16 ERTD3FFL]160S 16 3200 2.30 Ñ ] 20 3200 2.30 Ñ ] 30 3200 2.30 Ñ ] ERTD3FFL 400S 40 3200 ERTD3FGL]750S 75 3700 ERTD3FGL]800S 80 ] ERTD2FIL 154S ERTD3FEL 8R0S ERTD3FFL 200S ERTD3FFL 300S 2.30 Ñ 2.62 Ñ 3700 2.62 Ñ 130 3700 2.62 Ñ ERTD3FGL 501S 500 4000 2.83 Ñ ERTD3FHL]402S 4000 4100 2.90 Ñ 20000 4500 3.22 Ñ 80000 5000 3.70 17 ] ERTD3FGL 131S ] ] ERTD3FHL 203S ] ERTD3FIL 803S ] 0.6 Resistance Tolerance Code J K L ±5 % ±10 % ±15 % Tolerance of ÒB valueÓ: ±10 % kn (R25/R50) R25=Resistance at 25.0 ¡C B= R50=Resistance at 50.0 ¡C 1/298.15Ð1/323.15 ]] 7.0 27 l Operating Temperature Range: Ð30 to +125 ¡C NTC Thermistors (Disc Type) n Dimensions in mm (not to scale) Straight Lead Type F Type Crimped Lead Type Z Type F Type fD T k W fd D2 5.0±0.5 1.3±0.5 30.0 min. 2.5±1.0 0.4 D3 7.5±0.5 1.4±0.5 30.0 min. 5.0±1.0 0.5 Z Type fD D2 5.0±0.5 T u 1.3±0.5 3.0 max. (nom.2.5) h W fd 4.5±1.0 6.0 max. (nom.5.0) 5.0±1.0 0.5 n Voltage vs. Current (Table B) Ω Ω Ω Ω Ω Ω n Resistance vs. Temperature (Table A) e × NTC Thermistors (Disc Type) n Resistance Color Code Code 1(1st Digit) 2(2nd Digit) 3(Multiplier) Black 0 0 100 Brown 1 1 101 Red 2 2 102 Orange 3 3 103 Yellow 4 4 104 Green 5 5 105 Blue 6 6 106 Purple 7 7 107 Gray 8 8 108 White 9 9 109 Gold Ñ Ñ 10Ð1 Silver Ñ Ñ 10Ð2 Color n Taping Dimensions in mm (not to scale) Taping Type P P0 P1 P2 fd F Æh W W0 W1 W2 H H0 k fD0 t 12.7±1.0 12.7±0.3 3.85±0.70 6.35±1.30 0.50±0.05 5.0±1.0 0±5.0 18.0+1.0 Ð0.5 12.5 min. 9.00+0.75 Ð0.50 3.0 max 21.0±2.0 16.0±0.5 2.0 max. 4.0±0.3 0.5±0.2 NTC Thermistors (Disc Type) Disc Type NTC Thermistors Handling Precautions Safety Precautions The Disc Type NTC Thermisters (hereafter referred to as ÒThe NTC ThermistorsÓ) may fail in burnout, flaming or glowing in the worst case, when subjected to severe conditions of electrical, environmental and/or mechanical stresses. The following Ò Safety PrecautionsÓ and ÒApplication NotesÓ should be taken into consideration. For any questions regarding the ÒHandling PrecautionsÓ, please contact our engineering section or factory. 1. Precautions for Safety 1.1 Operating Power The NTC Thermistors should not be operated beyond their specified Maximum Permissible Power in the Catalog or the Individual Specifications, otherwise , burnout or damages due to the thermal run awa could result. (if operated in ambient temperature above 25 ¡C, power rating should be derated in accordance with the derating curve.) 1.2 Operating Temperature Range The NTC Thermistors should not be operated beyond their specified Operating Temperature Range of in the Catalog or the Individual Specifications. (Do not touch the heated part of the NTC Themistors by hand during operation) 1.3 Plastic Molding and Potting In case of plastic molding or potting, the NTC Thermistors may be damaged or deteriorated by extreme mechanical stresses such as expanding and shrinking forces caused by the heat treatment of the plastics applied (depending on curing conditions and types of plastics) 1.4 Environmental Conditions The NTC Thermistors should not be operated and/or stored under the following environmental conditions; a) Direct exposure to water or drops of water. b) Direct exposure to sunlight. c) Under conditions of high humidity or water condensation. d) Direct exposure to oil, gasoline or organic solvent and/or atomospheres of them. e) Under conditions of deoxidized or corrosive atomospheres such as chlorine, hydrogen sulfide, sulfur oxide or vinyl chloride. f) Under severe conditions of extreme vibration or shock. 1.5 Mounting Do not let other parts touch the Thermistors because other coating is not a generated insulator. 1.6 Fail-Safe Design for Equipment In application of the Termistors, equipment should be protected against deterioration and failures of the Thermistors. 2. Application Notes 2.1 Soldering Flux Rosin-based and non-activated type soldering flux is recommended. 2.2 Post Soldering Cleaning In case of solvent cleaning, outer coating material of the NTC Thermistors may acquire the solvent, depending on the cleaning condition and type of cleaning solvent. 2.3 Abnormal Mechanical Stresses The NTC Thermistors may be damaged or deteriorated, when dropped or exposed to a large impact. Excessive shock and impact should not be applied. 2.4 Soldering (1) When soldering the thermistor, solder for as short time as possible to minimize the exposure time of the element to the melting point of solder. Take into account the solder-heat resistance of the product before use. (2) In soldering the device, the body and outer coating section should not be touched by molten solder and/or heated iron tip. 2.5 Long Term Storage (1) NTC Thermistors should not be stored under severe conditions of high temperature and/or high humidity. (2) NTC Thermistors should not be stored under conditions of corrosive atomospheres such as hydrogen sulfide, sulfur oxide, chlorine, and ammonia etc. (3) NTC Thermistors should not be exposed to direct sunlight. (4) NTC Thermistors should not be stored under conditions of condensation. (5) Store them indoors under 40 ¡C max. and 75 %RH max. Use them within one year of manufacture and check the solderability before use.