HiPerDynFREDTM Epitaxial Diode IFAV VRRM trr ISOPLUS220TM Electrically Isolated Back Surface Preliminary Data Sheet VRSM VRRM V V 600 600 600 600 DSEA ISOPLUS 220TM Type 1 DSEC 2 3 DSEA 16-06AC DSEC 16-06AC 1 1 Symbol 2 Conditions 3 TC = 120°C; rectangular, d = 0.5 A A IFSM TVJ = 45°C; tp = 10 ms (50 Hz), sine 50 A EAS TVJ = 25°C; non-repetitive IAS = 0.9 A; L = 180 µH 0.1 mJ IAR VA = 1.5·VR typ.; f = 10 kHz; repetitive 0.1 A -55...+175 175 -55...+150 °C °C °C 260 °C 50 W 2500 V~ 11...65 / 2.5...15 N / lb 2 g TL 1.6 mm (0.063 in) from case for 10 s Ptot TC = 25°C VISOL 50/60 Hz RMS; IISOL ≤ 1 mA FC mounting force with clip Weight typical z z z z z z z z z Symbol Conditions IR TVJ = 25°C VR = VRRM TVJ = 150°C VR = VRRM 60 0.25 µA mA Characteristic Values typ. max. IF = 10 A; 1.42 2.10 V V z z TVJ = 150°C TVJ = 25°C RthJC RthCH trr IRM Isolated back surface* 3 0.6 Silicon chip on Direct-Copper-Bond substrate - High power dissipation - Isolated mounting surface - 2500V electrical isolation Low cathode to tab capacitance (<15pF) Planar passivated chips Very short recovery time Extremely low switching losses Low IRM-values Soft recovery behaviour Epoxy meets UL 94V-0 Applications z VF d 3 Features z TVJ TVJM Tstg c 2 Maximum Ratings 35 8 IFRMS IFAVM DSEA 16-06AC DSEC 16-06AC = 2x8 A = 600 V = 35 ns z z z Antiparallel diode for high frequency switching devices Antisaturation diode Snubber diode Free wheeling diode in converters and motor control circuits Rectifiers in switch mode power supplies (SMPS) Inductive heating Uninterruptible power supplies (UPS) Ultrasonic cleaners and welders K/W Advantages K/W Avalanche voltage rated for reliable ns operation Soft reverse recovery for low EMI/RFI Low IRM reduces: A - Power dissipation within the diode - Turn-on loss in the commutating switch z IF = 1 A; -di/dt = 50 A/µs; VR = 30 V; TVJ = 25°C 35 VR = 100 V; IF = 12 A; -diF/dt = 100 A/µs TVJ = 100°C 3.5 z 4.4 Notes: Data given for TVJ = 25OC and per diode unless otherwise specified c Pulse test: pulse Width = 5 ms, Duty Cycle < 2.0 % d Pulse test: pulse Width = 300 µs, Duty Cycle < 2.0 % IXYS reserves the right to change limits, test conditions and dimensions. z See DSEC 16-06A data sheet for characteristic curves. DS98831(9/03) © 2003 IXYS All rights reserved DSEA 16-06AC DSEC 16-06AC ISOPLUS220 Outline Note: All terminals are solder plated. DSEA: 1 - Cathode 2 - Anode 3 - Cathode DSEC: 1 -Anode 2 - Cathode 3 - Anode