Panasonic AN7511 Btl audio power ic Datasheet

New
BTL Audio Power IC AN7510/7520 Series
■ Overview
The AN7510/7520 series is a 0.5W to 3W BTL audio power amplifier IC. Equipped with a standby function and mute or DC
volume circuit, the series includes a lineup of single and dual output models. With simplified set design due to minimum
external components, this IC has a wide variety of applications.
■ Features
• Operating power sourcs voltage: 3.0V to 13.5V.
• Built-in standby function.
• Built-in mute or DC volume circuit.
■ Specifications
Parameters
Product
name
Output
power
Vcc
Load
resistance
AN7510S
0.5W×2ch
5V
16Ω
SOP-16pin
AN7511S
0.5W×1ch
5V
16Ω
SOP-8pin
AN7512S
0.5W×2ch
5V
16Ω
SOP-16pin
AN7513S
0.5W×1ch
5V
16Ω
SOP-8pin
AN7510
1.0W×2ch
5V
8Ω
HDIP-16pin
AN7511
1.0W×1ch
5V
8Ω
DIP-8pin
AN7512
1.0W×2ch
5V
8Ω
HDIP-16pin
AN7513
1.0W×1ch
5V
8Ω
DIP-8pin
*
AN7520
3.0W×2ch
8V
8Ω
HSIP-12pin
*
AN7521
3.0W×1ch
8V
8Ω
HSIP-9pin
AN7522
3.0W×2ch
8V
8Ω
HSIP-12pin
AN7523
3.0W×1ch
8V
8Ω
HSIP-9pin
Standby
Mute
Volume
Package
* : Planned
■ Applications
● TVs ● Audio equipment ● Personal computers ● Active speakers
¶ The products and specifications are subject to change without any notice. Please ask for the latest product standards to guarantee the satisfaction of your product requirements.
Matsushita Electronics Corporation
1 Kotari Yakemachi, Nagaokakyo, Kyoto, 617-8520 Japan
Tel. (075) 951-8151
http://www.mec.panasonic.co.jp
New publication, effective from Jan. 13 1999.
Unit : mm
6.35±0.3
Dual 0.5,1W BTL Audio Power Amplifier Circuit
4.7±0.25
3.05
±0.25
21.6±0.3
27.4±0.3
1.06±0.25
■ Features
1
2
3
4
5
6
7
8
1.7
1.5±0.1
17
• AN7510: Vcc=5V,Output=1W(8Ω)
• AN7510S:Vcc=5V,Output=0.5W(16Ω)
• Built-in Standby function.
• Built-in Mute circuits.
0.5±0.1
16
15
14
13
12
11
10
9
3.80±0.3
φ2.1
0.5±0.1
1.2±0.25
AN7510
5.08±0.1
2.54±2.54
AN7510, AN7510S
0.45+0.1
–0.05
0 to 6
7.62±0.25
HDIP016-P-0300
■ Applications
Unit : mm
AN7510S
• TVs, Audio equipment, Personal computers,Active speakers
2
3
4
5
6
7
8
0.9±0.25
1
■ Block Diagram
N.C.
16
N.C.
9
N.C.
7
1
N.C.
SOP016-P-0300
Ripple
Rejection
Circuit
VCC 12
2 Standby
Attenuator
ch.1 Output
5.5±0.3
7.6±0.3
Attenuator
13
11
ch.2 Output
Thermal
Shutdown
28dB
15
28dB
6
ch.2 Input
5
Mute
GND
4
28dB
3
GND 14
(ch.1 Output)
8
Attenuator
control
ch.1 Input
ch.1 Output
28dB
ch.2 Output
10 GND
(ch.2 Output)
+0.1
(0.4)
10.09±0.3
0.2 –0.05
0.9±0.25
0.1±0.1
(0.4) 0.4±0.25 1.27
2.05±0.2
16 15 14 13 12 11 10 9
AN7510,7510S
■ Pin Descriptions
Pin No.
Function
Pin No.
Function
1
N.C
9
N.C
2
Standby
10
GND(Output ch2)
3
ch1 Input
11
ch2 Output(+)
4
GND(Input)
12
Vcc
5
Mute
13
ch1 Output(+)
6
ch2 Input
14
GND(Output ch1)
7
N.C
15
ch1 Output(-)
8
ch2 Output(-)
16
N.C
■ Absolute Maximum Ratings
Parameter
Symbol
Ratio
Unit
Note
ºC
1
Storage temperature
Tstg
AN7510
-55 to +150
AN7510S -55 to +125
Operating ambient temperature
Topr
-25 to +70
ºC
1
Supply voltage
Vcc
14
V
2
Supply current
Icc
2.0
A
Power dissipation
PD
1127
236
mW
AN7510
AN7510S
Note1) Ta=25ºC except storage temperature and operating ambient temperature.
Note2) At no-signal.
■ Operating Supply Voltage Range
Operating supply voltage range
Vcc
3.5V to 13.5V
Ta=70ºC
AN7510,7510S
■ Electrical Characteristics (Vcc=5.0V,RL=8Ω,freq=1kHz,Ta=25ºC ±2 ºC)
Parameter
Symbol
Condition
min.
typ.
max.
Unit
Quiescent current
ICQ
VIN=0mV
–
50
100
mA
Standby current
ISTB
VIN=0mV
–
1
10
µA
Output noise voltage
VNO
Rg=10kΩ
–
0.14
0.4
mVrms
Voltage gain
GV
PO=0.25W
32
34
36
dB
Total harmonic distortion
THD
PO=0.25W
–
0.05
0.5
%
Maximum power output
PO
THD=10%
0.8
1.1
–
W
Ripple rejection ratio
RR
Rg=10kΩ
Vr=1Vrms,fr=120Hz
30
50
–
dB
Output offset voltage
Voff
Rg=10kΩ
-300
0
300
mV
Muting effect
MT
PO=0.25W
70
86
–
dB
Channel balance
CB
PO=0.25W
-1
0
1
dB
Channel crosstalk
CT
PO=0.25W
55
65
–
dB
Note1) For this measurement,use the filter <Bandwidth:15Hz to 30kHz(12dB/octave)>
■ Application Circuit
10kΩ
VIN2
10
9
7
8
11
Mute
100kΩ
6
12
47kΩ
5
13
1.0µF
10kΩ
VIN1
Out2
8Ω
VCC
4
14
Standby
270kΩ
3
15
2
68kΩ
10µF
1
16
Out1
8Ω
Note
1
1
1
AN7510,7510S
■ Characteristic Curve(AN7510)
PO - VCC
PO,THD - VIN
8
10
100
7
Output Power PO (W)
Output Power PO (W)
6
5
ch.2
ch.1
4
freq=1kHz
THD=10%
RL=8Ω
400Hz HPF
30kHz LPF
2-ch Input
Rg=10kΩ
VSTB=5V
VMUTE=0V
3
2
1
2
4
6
8
10
12
10
0.1
VCC=5V
freq=1kHz
RL=8Ω
400Hz HPF
30kHz LPF
2-ch Input
Rg=10kΩ
VSTB=5V
VMUTE=0V
THD(10kHz)
0.01
THD(1kHz)
0.001
0
0
1
1
14
10
1
0.1
0.01
1000
100
Input Voltage VIN (mVrms)
Supply Voltage VCC (V)
■ Package Power Dissipation
■ Printed Board Circuit Layout
2000
1
1800
ch.2 Out−
Power Dissipation PD (mW)
1600
ch.2 Out+
1400
ch.1 Out+
1200
ch.1 Out−
1000
VCC
2
800
16
15
14
13
12
11
10
9
TAB
1
2
3
4
5
6
7
8
TAB
GND
600
3
400
200
0
0
25
50
75
100
125
150
Ambient Temperature Ta (°C)
1) AN7510:Rthj-a=71°C/W,PD=1761mW(25°C)
2) AN7510S:Rthj-a=127°C/W,PD=787mW(25°C)
Glass epoxy PCB(75mm×75mm×t0.8mm)
3) AN7510S:Rthj-a=233°C/W,PD=429mW(25°C)
GND(Input)
VIN(ch.2)
Mute/Volume
VIN(ch.1)
Standby
Total Harmonic Distortion THD (%)
PO(ch.1),PO(ch.2)
Unit : mm
AN7511
0.9
0.5,1W BTL Audio Power Amplifier Circuit
8
4
5
■ Features
0.3±0.26
3.89±0.2
6.4±0.2
• AN7511: Vcc=5V,Output=1W(8Ω)
• AN7511S:Vcc=5V,Output=0.5W(16Ω)
• Built-in Standby function.
• Built-in Mute circuits.
7.62±0.3
0.5
2.54 1.3
1.5
9.2±0.2
1
1.0
AN7511, AN7511S
3.35±0.2
+0.1
0.3 –0.05
0˚ to 15˚
DIP008-P-0300
■ Applications
Unit : mm
AN7511S
• TVs, Audio equipment, Personal computers,Active speakers
5.01±0.20
8
5
+0.10
0.15 –0.05
4.30±0.20
6.40±0.20
(1.05)
0 to 10
0.50±0.20
(0.60)
+0.10
1.27
0.40 –0.05
1.75max.
4
0.10±0.10 1.45±0.10
1
0.10
SEATING PLANE
■ Block Diagram
SOP008-P-0225C
Ripple
Rejection
Circuit
VCC 5
Attenuator
Output
6
Thermal
Shutdown
28dB
8
4
Mute
GND
3
28dB
2
GND Output 7
Attenuator
control
Input
Output
1 Standby
AN7511,7511S
■ Pin Descriptions
Pin No.
Function
1
Standby
2
ch1 Input
3
GND(Input)
4
Mute
5
Vcc
6
ch1 Output(+)
7
GND(Output1)
8
ch1 Output(-)
■ Absolute Maximum Ratings
Parameter
Symbol
Ratio
Unit
Note
Storage temperature
Tstg
-55 to +150
ºC
1
Operating ambient temperature
Topr
-25 to +70
ºC
1
Supply voltage
Vcc
14
V
2
Supply current
Icc
1.0
A
Power dissipation
PD
541
245
mW
AN7511
AN7511S
Note1) Ta=25ºC except storage temperature and operating ambient temperature.
Note2) At no-signal.
■ Operating Supply Voltage Range
Operating supply voltage range
Vcc
3.5V to 13.5V
Ta=70ºC
AN7511,7511S
■ Electrical Characteristics (Vcc=5.0V,RL=8Ω,freq=1kHz,Ta=25ºC ±2 ºC)
Parameter
Symbol
Condition
min.
typ.
max.
Unit
Quiescent current
ICQ
VIN=0mV
–
30
60
mA
Standby current
ISTB
VIN=0mV
–
1
10
µA
Output noise voltage
VNO
Rg=10kΩ
–
0.14
0.4
mVrms
Voltage gain
GV
PO=0.25W
32
34
36
dB
Total harmonic distortion
THD
PO=0.25W
–
0.05
0.5
%
Maximum power output
PO
THD=10%
0.8
1.1
–
W
Ripple rejection ratio
RR
Rg=10kΩ
Vr=1Vrms,fr=120Hz
30
50
–
dB
Output offset voltage
Voff
Rg=10kΩ
-300
0
300
mV
Muting effect
MT
PO=0.25W
70
86
–
dB
Note1) For this measurement,use the filter <Bandwidth:15Hz to 30kHz(12dB/octave)>
■ Application Circuit
5
6
VCC
VIN1
Mute
100kΩ
47kΩ
1.0µF
4
3
7
10kΩ
2
Standby
270kΩ
68kΩ
10µF
1
8
Out1
8Ω
Note
1
1
1
AN7511,7511S
■ Characteristic Curve(AN7511)
PO,THD - VIN
PO - VCC
8
10
100
7
THD(10kHz)
Output Power PO (W)
Output Power PO (W)
6
5
PO(8Ω)
4
freq=1kHz
THD=10%
RL=8Ω
400Hz HPF
30kHz LPF
2-ch Input
Rg=10kΩ
VSTB=5V
VMUTE=0V
3
2
1
2
4
6
8
10
12
10
0.1
VCC=5V
freq=1kHz
RL=8Ω
400Hz HPF
30kHz LPF
2-ch Input
Rg=10kΩ
VSTB=5V
VMUTE=0V
THD(100kHz)
0.01
THD(1kHz)
0
0
1
14
0.001
1
Supply Voltage VCC (V)
10
1
0.1
Total Harmonic Distortion THD (%)
PO
0.01
1000
100
Input Voltage VIN (mVrms)
■ Package Power Dissipation
■ Printed Board Circuit Layout
1000
Power Dissipation PD (mW)
900
1
800
ch.1 Out+
700
ch.1 Out−
2
600
VCC
8
7
6
5
1
2
3
4
500
3
400
GND
300
200
100
GND(Input)
0
0
25
50
70
75
100
125
150
Ambient Temperature Ta (°C)
1) AN7511:Rthj-a=148°C/W,PD=845mW(25°C)
2) AN7511S:Rthj-a=209.3°C/W,PD=597mW(25°C)
Glass epoxy PCB(50mm×50mm×t0.8mm)
3) AN7511S:Rthj-a=326.6°C/W,PD=383mW(25°C)
Mute/Volume
VIN(ch.1)
Standby
Unit : mm
6.35±0.3
Dual 0.5,1W BTL Audio Power Amplifier Circuit
4.7±0.25
3.05
±0.25
21.6±0.3
27.4±0.3
1.06±0.25
■ Features
1
2
3
4
5
6
7
8
1.7
1.5±0.1
17
• AN7512: Vcc=5V,Output=1W(8Ω)
• AN7512S:Vcc=5V,Output=0.5W(16Ω)
• Built-in Standby function.
• Built-in DC volume circuits.
0.5±0.1
16
15
14
13
12
11
10
9
3.80±0.3
φ2.1
0.5±0.1
1.2±0.25
AN7512
5.08±0.1
2.54±2.54
AN7512, AN7512S
0.45+0.1
–0.05
0 to 6
7.62±0.25
HDIP016-P-0300
■ Applications
Unit : mm
AN7512S
• TVs, Audio equipment, Personal computers,Active speakers
2
3
4
5
6
7
8
0.9±0.25
1
■ Block Diagram
N.C.
16
N.C.
9
N.C.
7
1
N.C.
SOP016-P-0300
Ripple
Rejection
Circuit
VCC 12
2 Standby
Attenuator
ch.1 Output
5.5±0.3
7.6±0.3
Attenuator
13
11
ch.2 Output
Thermal
Shutdown
28dB
15
28dB
6
ch.2 Input
5
Volume
GND
4
28dB
3
GND 14
(ch.1 Output)
8
Attenuator
control
ch.1 Input
ch.1 Output
28dB
ch.2 Output
10 GND
(ch.2 Output)
+0.1
(0.4)
10.09±0.3
0.2 –0.05
0.9±0.25
0.1±0.1
(0.4) 0.4±0.25 1.27
2.05±0.2
16 15 14 13 12 11 10 9
AN7512,7512S
■ Pin Descriptions
Pin No.
Function
Pin No.
Function
1
N.C
9
N.C
2
Standby
10
GND(Output ch2)
3
ch1 Input
11
ch2 Output(+)
4
GND(Input)
12
Vcc
5
DC volume
13
ch1 Output(+)
6
ch2 Input
14
GND(Output ch1)
7
N.C
15
ch1 Output(-)
8
ch2 Output(-)
16
N.C
■ Absolute Maximum Ratings
Parameter
Symbol
Ratio
Unit
Note
ºC
1
Storage temperature
Tstg
AN7512
-55 to +150
AN7512S -55 to +125
Operating ambient temperature
Topr
-25 to +70
ºC
1
Supply voltage
Vcc
14
V
2
Supply current
Icc
2.0
A
Power dissipation
PD
1127
236
mW
AN7512
AN7512S
Note1) Ta=25ºC except storage temperature and operating ambient temperature.
Note2) At no-signal.
■ Operating Supply Voltage Range
Operating supply voltage range
Vcc
3.5V to 13.5V
Ta=70ºC
AN7512,7512S
■ Electrical Characteristics (Vcc=5.0V,RL=8Ω,freq=1kHz,Ta=25ºC ±2 ºC)
Parameter
Symbol
Condition
min.
typ.
max.
Unit
Quiescent current
ICQ
VIN=0mV,Vol.=0V
–
35
100
mA
Standby current
ISTB
VIN=0mV,Vol.=0V
–
1
10
µA
Output noise voltage
VNO
Rg=10kΩ,Vol.=0V
–
0.10
0.4
mVrms
Voltage gain
GV
PO=0.25W,Vol.=1.25V
32
34
36
dB
Total harmonic distortion
THD
PO=0.25W,Vol.=1.25V
–
0.10
0.5
%
Maximum power output
PO
THD=10%,Vol.=1.25V
0.8
1.1
–
W
Ripple rejection ratio
RR
Rg=10kΩ,Vol.=0V
Vr=0.5Vrms,fr=120Hz
30
50
–
dB
Output offset voltage
Voff
Rg=10kΩ,Vol.=0V
-250
0
250
mV
Maximum attenuation
Att
PO=0.25W,Vol=0V
70
90
–
dB
Input impedance
ZI
VIN=±0.3VDC
24
30
36
kΩ
Channel balance1
CB1
PO=0.25W,Vol=1.25V
-1
0
1
dB
Channel balance2
CB2
PO=0.25W,Vol=0.6V
-3
0
3
dB
Center voltage gain
GVM
PO=0.25W,Vol=0.6V
22
25
28
dB
Channel crosstalk
CT
PO=0.25W,Vol=1.25V
40
55
–
dB
Note1) For this measurement,use the filter <Bandwidth:15Hz to 30kHz(12dB/octave)>
■ Application Circuit
Volume
VIN2
10
9
8
11
6
10kΩ
1.0µF
10kΩ
270kΩ
VIN1
1.0µF
7
12
5
14
3
13
15
2
68kΩ
10µF
1.0µF
Standby
Out2
8Ω
VCC
4
16
1
Out1
8Ω
Note
1
1
1
AN7512,7512S
■ Package Power Dissipation
2000
1
1800
Power Dissipation PD (mW)
1600
1400
1200
1000
2
800
600
3
400
200
0
0
25
50
75
100
125
150
Ambient Temperature Ta (°C)
1) AN7512:Rthj-a=71°C/W,PD=1761mW(25°C)
2) AN7512S:Rthj-a=127°C/W,PD=787mW(25°C)
Glass epoxy PCB(75mm×75mm×t0.8mm)
3) AN7512S:Rthj-a=233°C/W,PD=429mW(25°C)
■ Printed Board Circuit Layout
ch.2 Out−
ch.2 Out+
ch.1 Out+
ch.1 Out−
VCC
16
15
14
13
12
11
10
9
TAB
1
2
3
4
5
6
7
8
TAB
GND
GND(Input)
VIN(ch.2)
Mute/Volume
VIN(ch.1)
Standby
Unit : mm
AN7513
8
2
7
3
6
4
5
0.51 min.
6.3±0.3
■ Features
• AN7513: Vcc=5V,Output=1W(8Ω)
• AN7513S:Vcc=5V,Output=0.5W(16Ω)
• Built-in Standby function.
• Built-in DC volume circuits.
0.5±0.1
1
2.54
9.4±0.3
0.5,1W BTL Audio Power Amplifier Circuit
1.2±0.25
AN7513, AN7513S
3.8±0.25
(3.45)
+0.1
7.62±0.25
3 to 15°
0.15–0.05
DIP008-P-0300B
Unit : mm
8
2
7
3
6
4
5
0.3
4.2±0.3
6.5±0.3
■ Block Diagram
5.0±0.3
1
0.15
0.65
0.1±0.1
1.27
0.6±0.3
• TVs, Audio equipment, Personal computers
0.4±0.25
AN7513S
SOP008-P-0225A
Ripple
Rejection
Circuit
VCC 5
Attenuator
Output
6
Thermal
Shutdown
28dB
8
4
Volume
GND
3
28dB
2
GND Output 7
Attenuator
control
Input
Output
1 Standby
1.5±0.2
■ Applications
AN7513,7513S
■ Pin Descriptions
Pin No.
Function
1
Standby
2
ch1 Input
3
GND(Input)
4
DC volume
5
Vcc
6
ch1 Output(+)
7
GND(Output1)
8
ch1 Output(-)
■ Absolute Maximum Ratings
Parameter
Symbol
Ratio
Unit
Note
Storage temperature
Tstg
-55 to +150
ºC
1
Operating ambient temperature
Topr
-25 to +70
ºC
1
Supply voltage
Vcc
14
V
2
Supply current
Icc
1.0
A
541
245
mW
Power dissipation
AN7513
AN7513S
PD
Note1) Ta=25ºC except storage temperature and operating ambient temperature.
Note2) At no-signal.
■ Operating Supply Voltage Range
Operating supply voltage range
Vcc
3.5V to 13.5V
Ta=70ºC
AN7513,7513S
■ Electrical Characteristics (Vcc=5.0V,RL=8Ω,freq=1kHz,Ta=25ºC ±2 ºC)
Parameter
Symbol
Condition
min.
typ.
max.
Unit
Quiescent current
ICQ
VIN=0mV,Vol.=0V
–
20
60
mA
Standby current
ISTB
VIN=0mV,Vol.=0V
–
1
10
µA
Output noise voltage
VNO
Rg=10kΩ,Vol.=0V
–
0.10
0.4
mVrms
Voltage gain
GV
PO=0.25W,Vol.=2.5V
31
33
35
dB
Total harmonic distortion
THD
PO=0.25W,Vol.=2.5V
–
0.10
0.5
%
Maximum power output
PO
THD=10%,Vol.=2.5V
0.7
1.0
–
W
Ripple rejection ratio
RR
Rg=10kΩ,Vol.=0V
Vr=1.0Vrms,fr=120Hz
30
50
–
dB
Output offset voltage
Voff
Rg=10kΩ,Vol.=0V
-250
0
250
mV
Maximum attenuation
Att
PO=0.25W,Vol=0V
70
85
–
dB
Center voltage gain
GVM
PO=0.25W,Vol=0.1.25V
20.5
23.5
26.5
dB
Note1) For this measurement,use the filter <Bandwidth:15Hz to 30kHz(12dB/octave)>
■ Application Circuit
5
4
6
7
2
VCC
3
8
1
Out1
8Ω
Standby
10kΩ
270kΩ
68kΩ
10µF
1.0µF
VIN1
Volume
Note
1
1
1
AN7513,7513S
■ Package Power Dissipation
1000
Power Dissipation PD (mW)
900
1
800
700
2
600
500
3
400
300
200
100
0
0
25
50
70
75
100
125
150
Ambient Temperature Ta (°C)
1) AN7513:Rthj-a=148°C/W,PD=845mW(25°C)
2) AN7513S:Rthj-a=209.3°C/W,PD=597mW(25°C)
Glass epoxy PCB(50mm×50mm×t0.8mm)
3) AN7513S:Rthj-a=326.6°C/W,PD=383mW(25°C)
■ Printed Board Circuit Layout
ch.2 Out−
ch.2 Out+
ch.1 Out+
ch.1 Out−
VCC
16
15
14
13
12
11
10
9
TAB
1
2
3
4
5
6
7
8
TAB
GND
GND(Input)
VIN(ch.2)
Mute/Volume
VIN(ch.1)
Standby
AN7522
Unit : mm
7.7±0.3
(1.27)
0.6 +0.15
–0.05
(1.27)
R1.8
■ Applications
(1.2)
19.1±0.3
21.9±0.3
HSIP012-P-0000A
• TVs, Audio equipment, Personal computers,Active speakers
12
ch.2 Output
GND 11
(ch.2 Output)
10
ch.2 Output
9
Volume
8
ch.2 Input
7
GND
6
ch.1 Input
5
Standby
4
ch.1 Output
GND 3
(ch.1 Output)
ch1. Output 2
VCC 1
■ Block Diagram
1.45±0.15
3.5±0.3
1.2±0.1
(12.5)
1.80±0.15
• Vcc=8V,Output=3W(8Ω)
• Built-in Standby function.
• Built-in DC volume circuits.
1
0.25+0.10
–0.05 2.54
0.6
■ Features
φ3.6
29.6±0.3
29.75±0.30
28.0±0.3
20.0±0.3
(10.0)
(10.0)
(1.3)
12
Dual 3W BTL Audio Power Amplifier Circuit
AN7522
■ Pin Descriptions
Pin No.
Function
Pin No.
Function
1
Vcc
7
GND(Intput)
2
ch1 Output(+)
8
ch2 Input
3
GND(Output ch1)
9
DC Volume
4
ch1 Output(-)
10
ch2 Output(-)
5
Standby
11
GND(Output ch2)
6
ch1 Input
12
ch2 Output(+)
■ Absolute Maximum Ratings
Parameter
Symbol
Ratio
Unit
Note
Storage temperature
Tstg
-55 to +150
ºC
1
Operating ambient temperature
Topr
-25 to +70
ºC
1
Supply voltage
Vcc
14
V
2
Supply current
Icc
2.0
A
Power dissipation
PD
1920
mW
Note1) Ta=25ºC except storage temperature and operating ambient temperature.
Note2) At no-signal.
■ Operating Supply Voltage Range
Operating supply voltage range
Vcc
3.5V to 13.5V
Ta=70ºC
AN7522
■ Electrical Characteristics (Vcc=5.0V,RL=8Ω,freq=1kHz,Ta=25ºC ±2 ºC)
Parameter
Symbol
Condition
min.
typ.
max.
Unit
Quiescent current
ICQ
VIN=0mV,Vol.=0V
–
45
100
mA
Standby current
ISTB
VIN=0mV,Vol.=0V
–
1
10
µA
Output noise voltage
VNO
Rg=10kΩ,Vol.=0V
–
0.10
0.4
mVrms
Voltage gain
GV
PO=0.25W,Vol.=1.25V
32
34
36
dB
Total harmonic distortion
THD
PO=0.25W,Vol.=1.25V
–
0.10
0.5
%
Maximum power output
PO
THD=10%,Vol.=1.25V
2.4
3.0
–
W
Ripple rejection ratio
RR
Rg=10kΩ,Vol.=0V
Vr=0.5Vrms,fr=120Hz
30
50
–
dB
Output offset voltage
Voff
Rg=10kΩ,Vol.=0V
-250
0
250
mV
Maximum attenuation
Att
PO=0.25W,Vol=0V
70
90
–
dB
Input impedance
ZI
VIN=±0.3VDC
24
30
36
kΩ
Channel balance1
CB1
PO=0.25W,Vol=1.25V
-1
0
1
dB
Channel balance2
CB2
PO=0.25W,Vol=0.6V
-3
0
3
dB
Center voltage gain
GVM
PO=0.25W,Vol=0.6V
21
24
27
dB
Channel crosstalk
CT
PO=0.25W,Vol=1.25V
44
55
–
dB
Note1) For this measurement,use the filter <Bandwidth:15Hz to 30kHz(12dB/octave)>
VCC
Standby VIN1
VIN2 Volume
8Ω
Out2
12
11
10
9
8
1.0µF
10kΩ
7
6
10kΩ
270kΩ
68kΩ
8Ω
Out1
10µF
470µF
1.0µF
5
4
3
2
1
■ Application Circuit
Note
1
1
1
AN7522
■ Characteristic Curve
PO - VCC
PO,THD - VIN
6
5
Output Power PO (W)
7
Output Power PO (W)
10
freq=1kHz
THD=10%
RL=8Ω,16Ω
400Hz HPF
30kHz LPF
2-ch Input
Rg=10kW
VSTB=5V
Vol.=1.25V
ch.2(8Ω)
4
3
2
VCC=8V
freq=1kHz
RL=8Ω
400Hz HPF
30kHz LPF
1
10
THD
(ch.2,100kHz)
THD
(ch.1,100kHz)
1
0.1
THD(ch.2,10kHz)
THD(ch.1,10kHz)
0.01
0.1
PO(ch.1)
ch.1, ch.2(16Ω)
THD
(ch.1,1kHz)
ch.1(8Ω)
1
100
2-ch Input
Rg=10kΩ
VSTB=5V
Vol.=1.25V
Total Harmonic Distortion THD (%)
8
THD(ch.2,1kHz)
PO(ch.2)
0
0.001
0
2
4
6
8
10
12
14
1
10
Supply Voltage VCC (V)
■ Package Power Dissipation
0.01
1000
100
Input Voltage VIN (mVrms)
■ Printed Board Circuit Layout
13
Without heat sink
Rthj-a=41.7°C/W
Power Dissipation PD (mW)
12 5°C/W Heat sink
11
10
9
8
GND
7 10°C/W Heat sink
VCC
1
2
3
4
5
6
7
8
9
10
11
12
6
ch.1 Out+
5
4 20°C/W Heat sink
ch.1 Out−
3
ch.2 Out+
2
ch.2 Out−
1
0
0
25
50
70
75
100
125
150
Ambient Temperature Ta (°C)
GND(Input)
VIN(ch.2)
Mute/Volume
VIN(ch.1)
Standby
AN7523
Unit : mm
AN7523
φ2.65±0.10
8.4±0.25
5.8±0.25
6.3±0.3
7.1±0.25
3.75±0.25
1.5±0.25
15.0
22.3±0.3
φ3.3±0.1
2.54
■ Features
18.3±0.25
19.9±0.10
9
0.50±0.10
1.20±0.25
3W BTL Audio Power Amplifier Circuit
• Vcc=8V,Output=3W(8Ω)
• Built-in Standby function.
• Built-in DC volume circuits.
1
1.7±0.25
■ Applications
HSIP099-P-0000
• TVs, Audio equipment
Volume
9
8
N.C.
7
GND
6
Input
5
Standby
4
Output
3
GND Output
2
Output
VCC 1
■ Block Diagram
+0.10
0.45 –0.05
5.6±0.25
1.7±0.25
0.1±0.05
AN7523
■ Pin Descriptions
Pin No.
Function
1
Vcc
2
ch1 Output(+)
3
GND(Output1)
4
ch1 Output(-)
5
Standby
6
ch1 Input
7
GND
8
N.C
9
DC volume
■ Absolute Maximum Ratings
Parameter
Symbol
Ratio
Unit
Note
Storage temperature
Tstg
-55 to +150
ºC
1
Operating ambient temperature
Topr
-25 to +70
ºC
1
Supply voltage
Vcc
14
V
2
Supply current
Icc
1.0
A
Power dissipation
PD
1220
mW
Note1) Ta=25ºC except storage temperature and operating ambient temperature.
Note2) At no-signal.
■ Operating Supply Voltage Range
Operating supply voltage range
Vcc
3.5V to 13.5V
Ta=70ºC
AN7523
■ Electrical Characteristics (Vcc=5.0V,RL=8Ω,freq=1kHz,Ta=25ºC ±2 ºC)
Parameter
Symbol
Condition
min.
typ.
max.
Unit
Quiescent current
ICQ
VIN=0mV,Vol.=0V
–
25
60
mA
Standby current
ISTB
VIN=0mV,Vol.=0V
–
1
10
µA
Output noise voltage
VNO
Rg=10kΩ,Vol.=0V
–
0.10
0.4
mVrms
Voltage gain
GV
PO=0.25W,Vol.=1.25V
31
33
35
dB
Total harmonic distortion
THD
PO=0.25W,Vol.=1.25V
–
0.10
0.5
%
Maximum power output
PO
THD=10%,Vol.=1.25V
2.4
3.0
–
W
Ripple rejection ratio
RR
Rg=10kΩ,Vol.=0V
Vr=0.5Vrms,fr=120Hz
30
50
–
dB
Output offset voltage
Voff
Rg=10kΩ,Vol.=0V
-250
0
250
mV
Maximum attenuation
Att
PO=0.5W,Vol=0V
70
85
–
dB
Center voltage gain
GVM
PO=0.5W,Vol=0.6V
20.5
23.5
26.5
dB
Standby terminal current
ISTB
VIN=0mV,VSTB=3V
–
–
25
µA
Volume terminal current
Ivol
VIN=0mV,Vol=0V
-12
–
–
µA
Note1) For this measurement,use the filter <Bandwidth:15Hz to 30kHz(12dB/octave)>
VCC
9
8
7
6
10kΩ
270kΩ
68kΩ
8Ω
Out1
10µF
470µF
1.0µF
5
4
3
2
1
■ Application Circuit
Standby VIN1
Volume
Note
1
1
1
AN7523
■ Characterristic Curve
PO - VCC
PO,THD - VIN
10
7
Output Power PO (W)
6
5
Output Power PO (W)
freq=1kHz
THD=10%
RL=8Ω,16Ω
400Hz HPF
30kHz LPF
2-ch Input
Rg=10kΩ
VSTB=5V
Vol.=1.25V
4
8Ω
3
VCC=8V
freq=1kHz
RL=8Ω
400Hz HPF
30kHz LPF
100
2-ch Input
Rg=10kΩ
VSTB=5V
Vol.=1.25V
1
10
THD(10kHz)
1
0.1
THD(100kHz)
0.1
0.01
2
PO
16Ω
THD(1kHz)
1
0.001
0
0
2
4
6
8
10
12
1
14
10
Supply Voltage VCC (V)
■ Package Power Dissipation
Total Harmonic Distortion THD (%)
8
0.01
1000
100
Input Voltage VIN (mVrms)
■ Printed Board Circuit Layout
2000
Power Dissipation PD (mW)
1800
Without heat sink
Rthj-a=65.5°C/W
PD=1880mW(25°C)
1600
GND
1400
VCC
1200
ch.1 Out+
1000
ch.1 Out−
1
2
3
4
5
6
7
8
9
GND(Input)
800
Mute/Volume
VIN(ch.1)
Standby
600
400
200
0
0
25
50
75
100
125
Ambient Temperature Ta (°C)
150
Similar pages